Quantifying the Effects of Near-Surface Viscosity on Seismic Acquisition Geometry: A case study from Chepaizi Exploration Area, Junggar Basin (NW China)

The Chepaizi Exploration Area,Junggar Basin(NW China)holds substantial importance for seismic exploration endeavors,yet it poses notable challenges due to the intricate nature of its subsurface and near-surface conditions.To address these challenges,we introduce a novel and comprehensive workflow tailored to evaluate and optimize seismic acquisition geometries while considering the impacts of near-surface viscosity.By integrating geological knowledge,historical seismic data,and subsurface modeling,we conduct simulations employing the visco-acoustic wave equation and reverse-time migration to produce detailed subsurface images.The quality of these images is quantitatively evaluated using a local similarity metric,a pivotal tool for evaluating the accuracy of seismic imaging.The culmination of this workflow results in an automated optimization strategy for acquisition geometries that enhances subsurface exploration.Our proposed methodology underscores the importance of incorporating near-surface viscosity effects in seismic imaging,offering a robust framework for improving the accuracy of subsurface imaging.Herein,we aim to contribute to the advancement of seismic imaging methodologies by providing valuable insights for achieving high-quality seismic exploration outcomes in regions characterized by complex subsurface and near-surface conditions.

A new type of fiber Bragg grating based seismic geophone

Aimed at the poor performance of conventional geophones in exploration for deeper and complex targets, we present the principle and theoretical design of a new geophone based on the optical fiber Bragg grating （FBG） sensing technology. The important parameters such as response functions are calculated theoretically. Because of the advantages of FBG sensing technology, the new FBG geophone has a high dynamic range of 94dB at （10-200 Hz）. This new generation of geophones will have wide use in seismic prospecting due to its higher sensitivity, lighter weight, and lower cost.

Research on seismic survey design for doubly complex areas

The complex geological conditions in doubly complex areas tend to result in difficult surface survey operations and poor target layer imaging in the subsurface which has a great impact on seismic data quality. In this paper, we propose an optimal crooked line survey method for decreasing the surface survey operational difficulties and improving the sub-layer event continuity. The method concentrates on the surface shooting conditions, first, selecting the proper shot positions based on the specific surface topographic features to reduce the shot difficulties and then optimizing the receiver positioning to meet the prerequisite that the subsurface reflection points remain in a straight line. Using this method cannot only lower the shooting difficulty of rough surface condition areas but also overcome the subsurface reflection point bending problem appearing in the traditional crooked line survey method. On the other hand, we use local infill shooting rather than conventional overall infill shooting to improve sublayer event continuity and uniformity with lower survey operation cost. A model has been calculated and processed with the proposed optimal crooked line survey and local infill shooting design method workflow and the results show that this new method can work for seismic surveys in double complex areas.

Controlled illumination and seismic acquisition geometry for target-oriented imaging

The conventional method of seismic data acquisition geometry design is based on the assumption of horizontal subsurface reflectors, which often is not suitable for complex structure. We start from a controlled illumination analysis and put forward a method of seismic survey geometry design for target-oriented imaging. The method needs a velocity model obtained by a preliminary seismic interpretation. The one-way Fourier finite-difference wave propagator is used to extrapolate plane wave sources on the target layer to the surface. By analyzing the wave energy distribution at the surface extrapolated from the target layer, the shot or receiver locations needed for target layer imaging can be determined. Numerical tests using the SEG-EAGE salt model suggest that this method is useful for confirming the special seismic acquisition geometry layout for target-oriented imaging.

Research of CRP-based irregular 2D seismic acquisition

Seismic exploration in the mountainous areas of western Chinese is extremely difficult because of the complexity of the surface and subsurface, which results in shooting difficulties, seismic data with low signal-to-noise ratio, and strong interference. The complexity of the subsurface structure leads to strong scattering of the refl ection points; thus, the curved-line acquisition method has been used. However, the actual subsurface structural characteristics have been rarely considered. We propose a design method for irregular acquisition based on common refl ection points（CRP） to avoid difficult-to-shoot areas, while considering the structural characteristics and CRP positions and optimizing the surfacereceiving line position. We arrange the positions of the receiving points to ensure as little dispersion of subsurface CRP as possible to improve the signal-to-noise ratio of the seismic data. We verify the applicability of the method using actual data from a site in Sichuan Basin. The proposed method apparently solves the problem of seismic data acquisition and facilitates seismic exploration in structurally complex areas.

Full wave seismic exploration technology

Reflected wave seismology has the following defects:the acquisition design is based on the assumption of layered media,the signal processing suppresses weak signals such as diffracted wave and scattered wave,and the seismic wave band after the image processing is narrow.They limit the full utilization of broadband raw data.The concept of full wave seismic exploration is redefined based on the idea of balanced utilization of reflected wave,diffracted wave and scattered wave information,its characteristics and adaptive conditions are clarified.A set of key technologies suitable for full wave seismic exploration are put forward.During seismic acquisition period,it is necessary to adopt multi geometry,i.e.embed small bin,small offset and small channel interval data in conventional geometry.By discretizing of common midpoint(CMP)gathers,small offset with high coverage,the weak signals such as diffracted wave and scattered wave in the raw seismic data can be enhanced.During seismic processing,the signal and noise in the original seismic data need to be redefined at first.The effective signals of seismic data are enhanced through merging of multi-geometry data.By means of differential application of data with different bin sizes and different arrangement modes,different regimes of seismic waves can be effectively decomposed and imaged separately.During seismic interpretation stage,making the most of the full wave seismic data,and adopting well-seismic calibration on multi-scale and multi-dimension,the seismic attributes in multi-regimes and multi-domains are interpreted to reveal interior information of complex lithology bodies and improve the lateral resolution of non-layered reservoirs.

High-resolution data acquisition technique in broadband seismic observation systems

The dynamic range of the currently most widely used 24-bit seismic data acquisition devices is 10–20 d B lower than that of broadband seismometers, and this can affect the completeness of seismic waveform recordings under certain conditions. However, this problem is not easy to solve because of the lack of analog to digital converter(ADC) chips with more than 24 bits in the market. In this paper, we propose a method in which an adder, an integrator, a digital to analog converter chip, a field-programmable gate array, and an existing low-resolution ADC chip are used to build a third-order 16-bit oversampling delta-sigma modulator. This modulator is equipped with a digital decimation filter, thus facilitating higher resolution and larger dynamic range seismic data acquisition. Experimental results show that, within the 0.1–40 Hz frequency range, the circuit board's dynamic range reaches 158.2 d B, its resolution reaches 25.99 bits, and its linearity error is below 2.5 ppm, which is better than what is achieved by the commercial 24-bit ADC chips ADS1281 and CS5371. This demonstrates that the proposed method may alleviate or even completely resolve the amplitude-limitation problem that so commonly occurs with broadband observation instruments during strong earthquakes.