The Yinchuan basin, located on the western margin of the Ordos block, has the characteristics of an active continental rift. A NW-striking deep seismic reflection profile across the center of Yinchuan basin precisely ...The Yinchuan basin, located on the western margin of the Ordos block, has the characteristics of an active continental rift. A NW-striking deep seismic reflection profile across the center of Yinchuan basin precisely revealed the fine structure of the crust. The images showed that the crust in the Yinchuan basin was characterized by vertical stratifications along a detachment located at a two-way travel time（TWT） of 8.0 s.The most outstanding feature of this seismic profile was the almost flat Mohorovicˇic′ discontinuity（Moho） and a high-reflection zone in the lower crust. This sub-horizontal Moho conflicts with the general assumption of an uplifted Moho under sedimentary basins and continental rifts, and may indicate the action of different processes at depth during the evolution of sedimentary basins or rifts.We present a possible interpretation of these deep processes and the sub-horizontal Moho. The high-reflection zone, which consists of sheets of high-density, mantlederived materials, may have compensated for crustal thinning in the Yinchuan basin, leading to the formation of a sub-horizontal Moho. These high-density materials may have been emplaced by underplating with mantlesourced magma.展开更多
To investigate the seismic behavior of I-section columns made of 460 MPa high strength steel （HSS）, six specimens were tested under constant axial load and cyclic horizontal load. The specimens were designed with di...To investigate the seismic behavior of I-section columns made of 460 MPa high strength steel （HSS）, six specimens were tested under constant axial load and cyclic horizontal load. The specimens were designed with different width-to-thickness ratios and loaded under different axial load ratios. For each specimen, the failure mode was observed and hysteretic curve was measured. Comparison of different specimens on hysteretic characteristic, energy dissipation capacity and deformation capacity were further investigated. Test results showed that the degradation of bearing capacity was due to local buckling of flange and web. Under the same axial load ratio, as width-to-thickness ratio increased, the deformation area of local buckling became smaller. And also, displacement level at both peak load and failure load became smaller. In addition, the full extent of hysteretic curve, energy dissipation capacity, ultimate story drift angle decreased, and capacity degradation occurred more rapidly with the increase of width-to-thickness ratio or axial load ratio. Based on the capacity of story drift angle, limiting values which shall not be exceeded are suggested respectively for flange and web plate of 460 MPa HSS I-section columns when used in SMFs and in IMFs in the case of axial load ratio no more than 0.2. Such values should be smaller when the axial load ratio increases.展开更多
The high-resolution shallow seismic technique can be used for more accurately prospecting the position and property of faults and for the preliminary study of fault activity.The author obtains many high quality stack ...The high-resolution shallow seismic technique can be used for more accurately prospecting the position and property of faults and for the preliminary study of fault activity.The author obtains many high quality stack time sections through the prospecting methods of different seismic sources,different group intervals and different observation systems on the Xiadian fault.These sections clearly display the stratum structure and the structure characteristics from several meters to several hundred meters of the Xiadian fault.The resolutions of the different seismic sources,different group intervals and different observing systems are obtained.The prospecting methods and work parameters applicable for goal stratum of different depths and different accuracy requirements are proposed through the analysis of the stack time sections.This lays a good foundation for raising the prospecting resolution of the fault position and the latest active time of the fault.展开更多
基金This study was financed jointly by the Sino Probe Project of China(Sinoprobe-02-01)the National Natural Science Foundation of China(Nos.41430213,41274097,and 41404072)+1 种基金Geological Investigation Project of China Geological Survey(Nos.1212011220260 and 12120115027101)‘‘Urban Active Fault Detection’’of National Development and Reform Commission(No.20041138)
文摘The Yinchuan basin, located on the western margin of the Ordos block, has the characteristics of an active continental rift. A NW-striking deep seismic reflection profile across the center of Yinchuan basin precisely revealed the fine structure of the crust. The images showed that the crust in the Yinchuan basin was characterized by vertical stratifications along a detachment located at a two-way travel time（TWT） of 8.0 s.The most outstanding feature of this seismic profile was the almost flat Mohorovicˇic′ discontinuity（Moho） and a high-reflection zone in the lower crust. This sub-horizontal Moho conflicts with the general assumption of an uplifted Moho under sedimentary basins and continental rifts, and may indicate the action of different processes at depth during the evolution of sedimentary basins or rifts.We present a possible interpretation of these deep processes and the sub-horizontal Moho. The high-reflection zone, which consists of sheets of high-density, mantlederived materials, may have compensated for crustal thinning in the Yinchuan basin, leading to the formation of a sub-horizontal Moho. These high-density materials may have been emplaced by underplating with mantlesourced magma.
基金the National Natural Science Foundation of China under Grant No.51478244
文摘To investigate the seismic behavior of I-section columns made of 460 MPa high strength steel （HSS）, six specimens were tested under constant axial load and cyclic horizontal load. The specimens were designed with different width-to-thickness ratios and loaded under different axial load ratios. For each specimen, the failure mode was observed and hysteretic curve was measured. Comparison of different specimens on hysteretic characteristic, energy dissipation capacity and deformation capacity were further investigated. Test results showed that the degradation of bearing capacity was due to local buckling of flange and web. Under the same axial load ratio, as width-to-thickness ratio increased, the deformation area of local buckling became smaller. And also, displacement level at both peak load and failure load became smaller. In addition, the full extent of hysteretic curve, energy dissipation capacity, ultimate story drift angle decreased, and capacity degradation occurred more rapidly with the increase of width-to-thickness ratio or axial load ratio. Based on the capacity of story drift angle, limiting values which shall not be exceeded are suggested respectively for flange and web plate of 460 MPa HSS I-section columns when used in SMFs and in IMFs in the case of axial load ratio no more than 0.2. Such values should be smaller when the axial load ratio increases.
基金supported by the project of "Experimental Exploration of Urban Active Faults" of the National Development and Reform Commission of China (20041138)
文摘The high-resolution shallow seismic technique can be used for more accurately prospecting the position and property of faults and for the preliminary study of fault activity.The author obtains many high quality stack time sections through the prospecting methods of different seismic sources,different group intervals and different observation systems on the Xiadian fault.These sections clearly display the stratum structure and the structure characteristics from several meters to several hundred meters of the Xiadian fault.The resolutions of the different seismic sources,different group intervals and different observing systems are obtained.The prospecting methods and work parameters applicable for goal stratum of different depths and different accuracy requirements are proposed through the analysis of the stack time sections.This lays a good foundation for raising the prospecting resolution of the fault position and the latest active time of the fault.
