采用自复位U形连接件的装配式钢框架-复合墙结构性能研究

对于内填RC墙的框架结构,为有效减小结构的损伤,改善结构力学性能,本文研究了一种在框架与墙之间设置开缝并安装耗能连接件,能够耗散能量从而有效地保护主体结构。采用ABAQUS分析了不同类型耗能连接件的内力特性以及节点的受力破坏模式。通过在两侧开缝的密肋复合墙-钢框架结构中设置可滑移连接,实现了节点的耗能作用。研究结构表明:U形连接件水平段长度对连接件极限位移影响较大,可以通过双折线理想弹塑性荷载-位移曲线描述U形连接件在竖向压力与水平剪切作用下的荷载-位移关系。采用耗能连接件的结构在加载前期残余变形小,具有一定的自复位能力,并且能满足结构的大变形要求。通过以上分析,本文基于承载能力极限状态提出了耗能连接件的设计公式。

Shake-table testing of a self-centering precast reinforced concrete frame with shear walls

The seismic performance of a self-centering precast reinforced concrete （RC） frame with shear walls was investigated in this paper. The lateral force resistance was provided by self-centering precast RC shear walls （SPCW）, which utilize a combination ofunbonded prestressed post-tensioned （PT） tendons and mild steel reinforcing bars for flexural resistance across base joints. The structures concentrated deformations at the bottom joints and the unbonded PT tendons provided the self-centering restoring force. A 1/3-scale model of a five-story self-centering RC frame with shear walls was designed and tested on a shake-table under a series of bi-directional earthquake excitations with increasing intensity. The acceleration response, roof displacement, inter-story drifts, residual drifts, shear force ratios, hysteresis curves, and local behaviour of the test specimen were analysed and evaluated. The results demonstrated that seismic performance of the test specimen was satisfactory in the plane of the shear wall; however, the structure sustained inter-story drift levels up to 2.45%. Negligible residual drifts were recorded after all applied earthquake excitations. Based on the shake-table test results, it is feasible to apply and popularize a self-centering precast RC frame with shear walls as a structural system in seismic regions.

Self-centering seismic retrofit scheme for reinforced concrete frame structures:SDOF system study

This paper presents the results of a parametric study of self-centering seismic retrofit schemes for reinforced concrete (RC) frame buildings. The self-centering retrofit system features flag-shaped hysteresis and minimal residual deformation. For comparison purpose,an alternate seismic retrofit scheme that uses a bilinear-hysteresis retrofit system such as buckling-restrained braces (BRB) is also considered in this paper. The parametric study was carried out in a single-degree-of-freedom (SDOF) system framework since a multi-story building structure may be idealized as an equivalent SDOF system and investigation of the performance of this equivalent SDOF system can provide insight into the seismic response of the multi-story building. A peak-oriented hysteresis model which can consider the strength and stiffness degradation is used to describe the hysteretic behavior of RC structures. The parametric study involves two key parameters -the strength ratio and elastic stiffness ratio between the seismic retrofit system and the original RC frame. An ensemble of 172 earthquake ground motion records scaled to the design basis earthquake in California with a probability of exceedance of 10% in 50 years was constructed for the simulation-based parametric study. The effectiveness of the two seismic retrofit schemes considered in this study is evaluated in terms of peak displacement ratio,peak acceleration ratio,energy dissipation demand ratio and residual displacement ratio between the SDOF systems with and without retrofit. It is found from this parametric study that RC structures retrofitted with the self-centering retrofit scheme (SCRS) can achieve a seismic performance level comparable to the bilinear-hysteresis retrofit scheme (BHRS) in terms of peak displacement and energy dissipation demand ratio while having negligible residual displacement after earthquake.

PEC柱-钢梁摩擦耗能部分自复位组合框架抗震试验研究

为系统研究梁柱采用自复位连接组合框架的抗震机理,选取预拉杆长度设置、PEC柱截面强弱轴布置和柱脚连接方式3个设计参数,设计制作了4榀PEC柱-钢梁梁柱摩擦耗能部分自复位连接组合框架1∶2缩尺试件并进行拟静力抗震试验。通过试验现象观察和数据分析,对试件的滞回特性、抗侧刚度退化、复位能力、滞回耗能等抗震性能进行研究。结果表明:摩擦耗能部分自复位连接通过T形件长圆孔合理设置实现了“设计地震水平阶段实现复位,大震设计水平阶段自复位连接连接转化为伴随出现螺栓承压型受力实现部分自复位”的性能化设计目标;设计地震阶段,试件主要通过辅助摩擦耗能件耗能,且卸载残余侧移小于自复位结构侧移限值(0.3%),在大震作用阶段,试件通过辅助摩擦耗能件与结构构件损伤联合耗能,承载能力仍继续增大,且仍具有部分自复位能力;预拉杆设置有限长度可显著增强结构整体性,PEC柱弱轴布置一定程度上降低了结构整体性,而PEC柱脚采用铰接可显著削弱结构整体性。

基于帧内-帧间自融合的双流泛化人脸伪造检测方法

现有人脸伪造检测方法往往在已知伪造类型上表现良好,但面对未知数据时检测性能有所下降,模型易受到过拟合的影响,检测泛化性不足。针对此问题,提出一种基于帧内-帧间自融合的双流泛化人脸伪造检测方法,从数据增强和检测器改进2个方面提高检测泛化性。设计帧内-帧间自融合模块,分别利用同帧人脸、帧间人脸进行数据增强:帧内自融合子模块利用同帧人脸生成训练数据,从而避免人脸图像身份信息干扰;帧间自融合子模块利用伪造视频的帧间不一致性,进一步构造多样性丰富、逼真的训练数据集,从而有效防止模型的过拟合,确保检测模型的泛化能力。此外,设计基于通道注意力机制的双流特征融合网络,在网络的浅层提取RGB特征、高频特征并进行融合来挖掘伪造信息,在提升模型性能的同时缓解网络的参数增长。将模型在4个数据集上与9种主流检测方法进行对比实验,结果表明:在跨数据集实验中,所提方法较次优方法AUC均值提高1.52个百分点,EER均值降低1.5个百分点;在跨伪造方法实验中,所提方法在4种伪造方法子数据集上均取得最优或次优效果。实验结果验证了该方法优秀的泛化能力。

基于分布参数模型的摇摆墙-框架结构协同性能分析

为了研究自复位摇摆墙-框架(rocking wall-moment frame,RWMF)结构的协同工作性能,利用所提出的分布参数模型对自复位RWMF结构的协同工作原理与基本影响规律进行研究,建立并求解了完整的静力和动力方程;得到RWMF结构的侧移、内力和各阶动态响应的闭合解,通过参数分析研究框架与摇摆墙(rocking wall,RW)之间的刚度特征值λ和RW底部旋转约束R_(f)对协同性能的影响,并采用层间位移集中系数(inter-story drift concentration factor,DCF)量化RW与框架之间的协同性能。结果表明:RW的设计应满足λ<10,否则,RW对协同性能的影响将微乎其微;当λ值适中时,RW底部约束可以增进协同作用,R_(f)>5后,其约束的继续增大不会再增进RW与框架间的协同效果;当λ和R_(f)取1≤λ≤5∩0.1<R_(f)≤10时,自复位RWMF结构可以在分布均匀性和减小主体框架损伤之间实现平衡,达到最优的协同性能。

DNA-有机分子两亲体自组装的研究进展

DNA-有机杂化两亲体在水溶液中可以自组装成各种形态,调节其自组装形态和大小通常需要改变分子内部结构,或改变组装条件和方法。因此,获得具有单一形态或尺寸变量的聚集体是一个巨大的挑战。近年来,有学者首次提出了一种新的框架引导组装策略,即引导两亲体沿着锚定在框架上的疏水性基团聚集,最终按照预先设计的框架形成具有一定形状和均匀大小的形态。该策略突破了传统组装方法的限制,使制备具有可编程几何形状和尺寸的聚集体成为可能,为构建纳米结构提供了新的思路和方法,并在纳米科学和生物医学方面具有潜在的应用前景。

Test and simulation of full-scale self-centering beam-to-column connection

A new type of beam-to-column connection for steel moment flames, designated as a ＂self-centering connection,＂ is studied. In this connection, bolted top-and-seat angles, and post-tensioned （PT） high-strength steel strands running along the beam are used. The PT strands tie the beam flanges on the column flange to resist moment and provide self-centering force. After an earthquake, the connections have zero deformation, and can be restored to their original status by simply replacing the angles. Four full-scale connections were tested under cyclic loading. The strength, energy-dissipation capacity, hysteresis curve, as well as angles and PT strands behavior of the connections are investigated. A general FEM analysis program called ABAQUS 6.9 is adopted to model the four test specimens. The numerical and test results match very well. Both the test and analysis results suggest that： （1） the columns and beams remain elastic while the angles sustain plastic deformations for energy dissipation when the rotation of the beam related to the column equals 0.05 tad, （2） the energy dissipation capacity is enhanced when the thickness of the angle is increased, and （3） the number of PT strands has a significant influence on the behavior of the connections, whereas the distance between the strands is not as important to the performance of the connection.

Numerical simulation of the seismic behavior of self-centering steel beam-column connections with bottom flange friction devices

A new type of steel moment resisting frame with bottom flange friction devices （BFFDs） has been developed to provide self-centering capacity and energy dissipation, and to reduce permanent deformations under earthquakes. This paper presents a numerical simulation of self-centering beam-column connections with BFFDs, in which the gap opening/closing at the beam-column interfaces is simulated by using pairs of zero-length elements with compression-only material properties, and the energy dissipation due to friction is simulated by using truss elements with specified hysteretic behavior. In particular, the effect of the friction bolt bearing against the slotted plate in the BFFDs was modeled, so that the increase in lateral force and the loss of friction force due to the bolt bearing could be taken into account. Parallel elastic-perfectly plastic gap （ElasticPPGap） materials in the Open System for Earthquake Engineering Simulation （OpenSees） were used with predefined gaps to specify the sequence that each bolt went into the bearing and the corresponding increase in bending stiffness. The MinMax material in OpenSees is used to specify the minimum and maximum values of strains of the ElasticPPGap materials. To consider the loss of friction force due to bok bearing, a number of parallel hysteretic materials were used, and the failure of these materials in sequence simulated the gradual loss of friction force. Analysis results obtained by using the proposed numerical model are discussed and compared with the test results under cyclic loadings and the seismic loading, respectively.

Parameter Self - Learning of Generalized Predictive Control Using BP Neural Network

This paper describes the self—adjustment of some tuning-knobs of the generalized predictive controller(GPC).A three feedforward neural network was utilized to on line learn two key tuning-knobs of GPC,and BP algorithm was used for the training of the linking-weights of the neural network.Hence it gets rid of the difficulty of choosing these tuning-knobs manually and provides easier condition for the wide applications of GPC on industrial plants.Simulation results illustrated the effectiveness of the method.

Self - Crosslinking Behavior of Self - Emulsion Water - Based Polyure-thane Coating Agents

The relation between structures and properties of polyurethane are investigated by modern physical and chemical methods.The results obtained are as follows:the effects of the content of self-crosslinking agent on the properties of polyurethane,i.e.,dispersion stability,dynamical viscoelasticity and mechanical properties are discussed.It is found that the optimum molar ratio of epichlorohydrin and diethylenetriamine is 1:2.A mois-

Culture Self- Consciousness in Transmission of Chinese Philosophy from the Perspective of English Globalization -- Taking the Belt and Road Initiative for Example

The Belt and Road Initiative contains the aspiration of Chinese nation to pursue ideological freedom and desire of strengthening international exchanges and cooperation. This paper takes the Belt and Road Initiative for example,emphasizing the interpretation of the inheritance and development of Chinese culture so as to study the importance of Culture Self-Consciousness in Chinese Philosophy,in the context of English globalization. That is to say,this paper stresses the spirits and the stand of nation 's demonstration on pursuing peace,cooperation and sustainable development in the civilization continuity from traditional China to the contemporary China,with practical philosophic view.

锚框校准和空间位置信息补偿的街道场景视频实例分割

街道场景视频实例分割是无人驾驶技术研究中的关键问题之一,可为车辆在街道场景下的环境感知和路径规划提供决策依据.针对现有方法存在多纵横比锚框应用单一感受野采样导致边缘特征提取不充分以及高层特征金字塔空间细节位置信息匮乏的问题,本文提出锚框校准和空间位置信息补偿视频实例分割(Anchor frame calibration and Spatial position information compensation for Video Instance Segmentation,AS-VIS)网络.首先,在预测头3个分支中添加锚框校准模块实现同锚框纵横比匹配的多类型感受野采样,解决目标边缘提取不充分问题.其次,设计多感受野下采样模块将各种感受野采样后的特征融合,解决下采样信息缺失问题.最后,应用多感受野下采样模块将特征金字塔低层目标区域激活特征映射嵌入到高层中实现空间位置信息补偿,解决高层特征空间细节位置信息匮乏问题.在Youtube-VIS标准库中提取街道场景视频数据集,其中包括训练集329个视频和验证集53个视频.实验结果与YolactEdge检测和分割精度指标定量对比表明,锚框校准平均精度分别提升8.63%和5.09%,空间位置信息补偿特征金字塔平均精度分别提升7.76%和4.75%,AS-VIS总体平均精度分别提升9.26%和6.46%.本文方法实现了街道场景视频序列实例级同步检测、跟踪与分割,为无人驾驶车辆环境感知提供有效的理论依据.

形状记忆合金混凝土框架建筑抗震性能研究

地震作用会造成钢筋混凝土框架发生平面和垂直方向的变形,导致其结构受到更大的地震力,加剧损伤程度。形状记忆合金(SMA)材料在外力作用下能够快速恢复变形前形状,降低框架损伤程度,进一步提高框架结构的承载能力和稳定性。基于此,有必要研究形状记忆合金混凝土框架建筑的抗震性能。以某实际工程为例,采用ANSYS软件建立钢筋混凝土框架有限元模型,选取天津地震波、北岭地震波、印度洋地震波及人工地震波作为地震震动输入,记录地震震动下时程结果。研究结果表明,预应力筋断裂后,该结构在地震作用下的滞回曲线为饱满的旗帜形,最大层间位移为1/125,残余变形在±10 mm之间,最高峰值荷载为211 kN,水平承载力较强,表明其自复位性能较高、地震响应效果较优、抗震承载力较强,可以有效提高建筑结构的安全性和可靠性。

预应力耗能钢框架抗连续倒塌机制研究

针对预应力耗能(PTED)钢框架结构的连续倒塌问题,采用ABAQUS软件建立精细化有限元模型,对框架结构拆除承重构件后不平衡荷载重分配的行为展开研究。并将有限元结果与1/3缩尺PTED钢框架的准静态试验结果进行对比分析,验证了模型的准确性。在此基础上,进一步开展了PTED钢框架抗连续倒塌受力机制的研究,并分析了初始预应力、预应力钢绞线数量、钢构件材料强度和梁翼缘宽厚比四种因素对钢框架抗连续倒塌机制的影响。结果表明:PTED钢框架抗连续倒塌过程主要包括三个阶段:初始阶段、压拱机制有利阶段和压拱机制不利阶段;倒塌抗力由预应力钢绞线拉力和梁柱之间的竖向作用力共同提供;提高初始预应力、预应力钢绞线数量、钢材屈服强度和降低梁翼缘宽厚比,均会使峰值荷载增大;钢绞线数量的增多使框架在失效柱位移较小时可以提供较大的抗力;增强梁柱构件抵抗局部屈曲变形的能力会提升预应力钢框架抗连续倒塌能力。

SMA碟簧群的循环受压性能及简化模型

该研究提出将多个形状记忆合金(SMA)碟簧片并联排列形成碟簧组,然后在碟簧组间加入垫片分隔、串联排列形成碟簧群,以提供更高的承载力及变形能力。采用有限元软件ABAQUS建立了一系列SMA碟簧群的三维精细化有限元模型,并进行非线性循环受压分析。结果表明:与钢碟簧的“三角形”荷载-位移曲线相比,SMA碟簧群的荷载-位移曲线呈现鲜明的“旗帜形”特性,具有明显的正向及反向转变平台。随着碟簧片数的增加,碟簧组的总可恢复变形量基本不变,极限承载力及割线刚度近似成比例增加,而随着碟簧组数的增加,碟簧群的总可恢复变形量增加,极限承载力不变,割线刚度近似成比例降低。因此,可根据碟簧群总极限承载力及变形能力的需要,灵活调整碟簧片及碟簧组的数量及布置方式。碟簧组的各层碟簧片由于边界条件不同,应力分布存在明显差异,而变形量亦呈现两端大中间小的哑铃形分布模式,其中加载端碟簧片变形量最大,若超过极限变形量可能发生翻转失效,值得注意。提出了SMA碟簧群的简化模型,通过简化及精细模型的非线性循环受压分析,发现该简化模型的循环受压荷载-位移曲线与精细模型吻合良好,而计算效率提高约38倍。将SMA碟簧群应用于自复位NZ梁柱节点中,并对自复位钢框架进行了验证性的滞回分析。结果表明:采用SMA碟簧群的自复位钢框架最大侧移为4%时可完全复位,且二次刚度相比采用预应力钢绞线的传统自复位钢框架提高近100%,极限承载力提高70%。

自复位支撑钢框架抗震性能评估与损伤演化分析

为研究自复位耗能(SCED)支撑失效前后支撑钢框架结构的抗震韧性及损伤演化规律,设计了一单榀三层自复位支撑钢框架(SCBSF)并对其进行精细化有限元模拟,探究了支撑第二刚度和摩擦力在考虑支撑失效时对结构宏观响应和关键构件损伤状态的影响规律。结果表明,在地震作用下,SCED支撑作为SCBSF第一道抗震防线,激活工作后为结构提供了稳定的耗能与卓越的复位能力,相比屈曲约束支撑(BRB)框架残余变形角最大减小了84.9%,显著降低结构震后修复成本;支撑达到最大行程破坏失效后,结构层间变形加剧,框架梁和柱塑性耗能占比增加了92.33%,主体结构损伤值增加了48.45%,结构的抗震性能与韧性水平明显降低。参数分析结果表明,提升支撑的第二刚度和摩擦力能有效降低结构响应,但具有较大第二刚度和摩擦力的支撑框架仍抵抗不了强震作用时,可能导致更多的支撑失效破坏,结构损伤加剧。因此,设计SCED支撑时,需要适当提高支撑第二刚度和摩擦力,建议第二刚度取值为第一刚度的7/50~4/25,支撑摩擦力与预压力比值取为1~1.2;提升支撑第二刚度相比提升摩擦力对结构损伤值控制效果更好,随着地震动强度增大,摩擦力与第二刚度对结构抗震性能的影响逐渐减小。

杭州电竞中心结构设计重难点概述

杭州电竞中心内圈主体结构采用钢框架-支撑结构,外圈采用“大倾角梭形斜柱+多段钢折梁框架”,是集承重与抗侧力于一体的结构体系,屋盖采用车辐式索承网格自平衡结构形式。详细介绍了地下结构、中央场馆结构的设计要点,门厅处利用建筑造型空间设计为多段钢折梁与跨层桁架相结合的结构形式;室内二层至三层楼面设计一浮空弧形人行桥,截面形式为薄壁钢箱梁,桥宽2.2m,跨度57m,采用“上挂下支”的稳定结构形式。对整体结构进行了静力弹性、动力弹塑性、振动台试验、典型节点有限元、整体稳定以及局部稳定等系列分析与试验。结果表明:结构在静力荷载和地震作用下强度和刚度均满足规范要求;典型节点极限承载力为荷载设计值的4.17倍;结构整体稳定性安全系数为3.79;斜柱局部稳定安全系数为2.52。合理的设计保证了结构的安全、经济和实用性。

基于深度学习的X线造影中肾上腺血管关键帧识别算法

原发性醛固酮增多症的分型诊断需进行肾上腺静脉取样,肾上腺静脉出现的帧称为关键帧。目前,关键帧的选取依赖于医生肉眼判断,耗时费力。该研究提出基于深度学习的关键帧识别算法。首先,采用小波去噪和多尺度血管增强滤波的方法,保留肾上腺静脉的形态特征。接着,结合自注意机制,得到改进的识别模型ResNet50-SA。与常用的迁移学习相比,新模型在准确率、精确度查准率、召回率、F1和AUC上都达到97.11%,优于其他模型,可帮临床医生快速识别肾上腺静脉中的关键帧。

基于QAR数据的波音747-400飞机巡航报文解析研究（英文）

为充分挖掘QAR数据中所包含的大量原始监控数据,检验ACARS报文的可靠性,更好地协助航空公司进行飞机和发动机的状态监控及故障诊断,对发动机稳态报文DFD的报文结构进行了解析研究,提出了一种从QAR数据中提取满足触发条件的DFD报文的研究思路和方法,以丰富发动机性能监控的信息量。通过对B747-400飞机实际ACARS报文数据和所提取的报文数据进行计算分析,验证了该方法的可靠性,具有良好的工程应用前景。