Novel self-assembled films of La-based phosphonate 3-aminopropyltriethoxysilane

Silane coupling reagent (3-aminopropyltriethoxysilane (APTES)) was prepared on single-crystal silicon substrates to form two-dimensional self-assembled monolayer (SAM). The terminal-NH2 groups in the film were in situ phosphorylated to -PO(OH)2 group to endow the film with good chemisorption ability. Then La-based thin films were deposited on phosphorylated APTES-SAM in order to make good use of the chemisorption ability of -PO(OH)2 groups. The thickness of the film was determined with ellipsometer, while phase transformation and surface morphology, surface energy, phase composition were analyzed by means of atomic force microscope (AFM), contact angle measurements and X-ray photoelectron spectroscopy (XPS). The results indicated that the terminal-NH2 groups could be completely transformed into desirable-PO(OH)2 groups after phosphorylation of APTES-SAM. Detailed XPS analysis of the La3+ peaks revealed that lanthanum element existed in the films in different states. As a result, conclusion could be made that lanthanum reacted with -PO(OH)2 groups on the surface of the substrate by chemical bond which would improve the bonding strength between the film and silicon substrate. Since the La-based thin films were well adhered to the silicon substrate, it might find promising application in the surface-modification of single-crystal Si and SiC in microelectromechanical systems (MEMS).

Characterization and tribological investigation of self-assembled MPTS-MPTES/RE composite films

γ-mercapto-propyl trimethoxysilane （MPTS） and γ-methacryloxy propyltrimethoxysilane （MPTES） were self-assembled on a hy- droxylated glass substrate to form a two-dimensional organic monolayer （MPTS-MPTES SAM）. The terminal thiol groups （-SH） in the MPTS-MPTES SAM were in-situ oxidized into sulfonic acid groups （-SO3H） to endow the film with good chemisorption ability. Then rare earth （RE） （lanthanum-based） composite thin films were prepared by self-assembly technique based on the as-prepared SAM, taking advantage of the chemisorption ability of the sulfonic acid groups. Automatic force microscope （AFM）, X-ray photoelectron spectrometry （XPS）, contact angle measurement and ellipsometer were used to characterize MPTS-MPTES/RE composite films. The macrofriction and wear behaviors of the films sliding against an AISI-52100 steel ball were examined on a unidirectional friction and wear tester, and the worn surface morphologies were observed on an AFM. The results showed that MPTS-MPTES/RE films had a low friction coefficient （0.09） and a long wear life （5980 sliding pass） at a light load （50 mN）. It indicated that the superior tribological properties of the MPTS-MPTES/RE composite films were attributed to the special characteristic of RE elements, the mobility of the films and good bonding strength.

Characterization and tribological investigation of self-assembled trimethoxysilyl-functionalized poly(phthalazinone ether ketone)thin films on glass substrates

Trimethoxysilyl-functionalized PPEK（PKGS） films had been designed to serve as wear resistant coatings for silicon surfaces. These surface films were formed by a dip-coating technique applied to self-assembled monolayers（SAMs）.The formation and wetting behavior of PKGS films were characterized by means of contact angle measurement.The friction coefficient of the film prepared is very low（about 0.1）,and the anti-wear behavior is good,with a lack of failure after sliding over 1800 s.

Hybrid Self-Assembled Multilayer Films Formed by Alternating Layers of Keggin Polyoxometalates and 1,10DAD

Hybrid self-assembled multilayer films were prepared by alternate adsorption of 1,10-diaminodecane (1,10-DAD) and Keggin polyoxometalates of SiW12O404-, SiW11VO405-, and PMo12O403-, respectively. The films were reproducibly grown at each adsorption cycle as monitored by UV spectroscopy.

Preparation and Characterization of SrTiO_3 Thin Film on Functional Organic Self-Assembled Monolayers

SrTiO3 thin film was successfully prepared on the functionalized organic self-assembled monolayers（SAMs） by the Liquid Phase Deposition（LPD） method.The as-prepared samples were characterized by X-ray diffraction（XRD）,atomic force microscope（AFM）,scanning electron microscopy（SEM） and metallographic microscope.Measurement of contact angle showed that the hydrophobe substrate was changed into hydrophile by UV irradiation.AFM photographs of octadecyl-trichloro-silane self-assembled monolayer（OTS-SAM） surface approved that UV irradiation did change the morphology of OTS monolayer and provided evidence for the conversion of hydrophilic characteristic.Photographs of Metallographic Microscope showed that OTS-SAM had an active effect on the deposition of SrTiO3 thin film.XRD and SEM indicated that the thin film was of pure cubic phase SrTiO3 and composed of nanosized grains with a size in the range of 100-500 nm.The formation mechanism of the SrTiO3 film was proposed.

FABRICATION AND AFM/FFM STUDIES OF C_(60)-CONTAINING POLYELECTROLYTE SELF-ASSEMBLED FILMS

An initial investigation on the roughness and frictional properties of the self-assembled thin films from polyelectrolytes is presented. Star-shaped C-60-Poly(styrene-maleic anhydride) was successful prepared. The multilayer thin films have been fabricated on mica with diazoresin as the cationic polyelectrolyte and hydrolyzed star-shaped C-60-poly(styrene-maleic anhydride) as the anionic polyelectrolyte via self-assembly technique. The crosslinking structure of the films is formed from the conversion of ionic bond to covalent bond after UV irradiation. AFM/FFM investigations provide insights into the roughness and frictional properties on a microscale. The roughness depends strongly on the number of film layers in the case of C-60-containing films. The frictional forces of the films exhibited a well behaved non-linear relationship in response to the change of applied load. It supports the prediction of enhanced load-bearing property Of C60-containing thin films.

Novel Covalently Linked Self-Assembled Films from a Functional Hyperbranched Conjugated Poly (Phenylene Vinylene)

A new self-assembled films of a functional dendritic molecule, hyperbranched conjugated poly (phenylene vinylene), is obtained through covalent bond linkage. The highly ordered and homogenous molecular films are obtained;and characterized by UV-vis spectra, fluorescent spectra and atomic force microscopy.

STABILITY AND ELECTROCHEMICAL PROPERTIES OF FULL-CONJUGATED SELF-ASSEMBLED FILMS BASED ON POLYANILINE AND ITS ACID-SUBSTITUTED DERIVATES

The stability of full-conjugated self-assembled （SA） multilayer films based on partially doped polyaniline （PANI） as a polycation and poly（o-aminobenzoic acid） （PCAN）, poly（aniline-2-sulfonic acid） （PSAN） as polyanions is investigated in alkali aqueous solutions. The self-assembled PANI-PCAN films keep their stability within 24 h in 1 mol/L NaOH solution,-the PANI-PSAN films, however, maintain the stability for 20 min in the same condition because the solubility of PSAN in alkali solutions is much higher than that of PCAN. The electrochemical properties of the SA films are determined, and the film-CdS composites formed in situ are also reported.

Self-assembled Synthesis of Porous TiO_2 Film on the Electrophoretic-deposited Titanate Nanoribbon Film

The porous TiOz film was self-assembled on the surface of electrophoretic-deposited titanate nanoribbon film without the addition of templates by using TiF4 as the precursor. It was found that the hydrolysis of TiF4 was accompanied with the self-assembly processes of TiO2 nanoparticles on the surface of electrophoretic-deposited titanate nanoribbon film, resulting in the formation of porous TiO2 structures. Titanate nanoribbon film was demonstrated to provide the active sites for the effective self-assembly of porous TiO2 nanostructures owing to a large amount of hydroxyl groups. Compared with the nonporous TiO2 film, the prepared porous TiO2 films obviously showed an enhanced photocatalytic activity, which could be attributed to the rapider diffusion and more efficient transport of various reactants and products during photocatalytic reaction in the t^orous structures.

Tribological Properties of Rare Earth Self-assembled Nanometer Film

Self-assembled film containing the rare earth (RE) elements was formed on a silicon dioxide substrate, in order to reduce the surface adhesion and the friction force of micro electro-mechanical systems (MEMS). The film thickness was measured as 2nm. The tribological experiment result shows that the friction coefficient of SiO 2 substrate reduces from 0.5 to 0.1 after the formation of RE self-assembled film on its surface. Besides, RE self-assembled film exhibits a high wear resistant ance.

A Facile Self-assembly Synthesis of Hexagonal ZnO Nanosheet Films and Their Photoelectrochemical Properties

Here, large-scale and uniform hexagonal zinc oxide(ZnO) nanosheet films were deposited onto indium tin oxide(ITO)-coated transparent conducting glass substrates via a facile galvanic displacement deposition process. Compared with other commonly used solution methods, this process avoids high temperature and electric power as well as supporting agents to make it simple and cost-effective. The as-fabricated ZnO nanosheet films have uniform hexagonal wurtzite structure. The photoelectrochemical(PEC) cell based on ZnO nanosheet film/ITO photoelectrode was also fabricated and its performance was improved by optimizing the solution concentration. A higher photocurrent density of*500 l A cm^(-2)under AM 1.5 G simulated illumination of 100 m W cm^(-2)with zero bias potential(vs. Ag/AgCl electrode) was obtained, which may ascribe to the increased surface-to-volume ratio of disordered Zn O nanosheet arrays. Our developed method may be used to deposit other oxide semiconductors, and the Zn O nanosheet film/ITO PEC cell can be used to design low-cost optoelectronic and photoelectrochemical devices.

Stability Behaviour of Monolayer Tetraether Lipids on the Amino-Silanised Silicon Wafer: Comparative Study between Langmuir-Blodgett Monolayers with Self-Assembled Monolayers

This study investigated the stability behaviour of molecular monolayer symmetric chemically modified tetraether lipids caldarchaeol-PO4 on the amino-silanised silicon wafer using Langmuir-Blodgett films, Self Assembling Monolayers (SAMs), ellipsometry, and atomic force microscopy (AFM). The monolayers of caldarchaeol-PO4 were stable on the solid surface amino-silanised silicon wafer. The organizations of molecular monolayers caldarchaeol-PO4 by Langmuir-Blodgett method and SAMs have been analyzed. The surface of pressure in Langmuir-Blodgett processing is carried out monolayers caldarchaeol-PO4 more flat island inhomogeneous. Another method of monolayers caldarchaeol-PO4 by SAMs is showed a large flat domain. Monolayers caldarchaeol-PO4 by Langmuir-Blodgett method seems to be stable and chemically resistant after washing with organic solvent and an additional treatment ultrasonification with various thickness lipids arround 2 nm to 6 nm. Conversely, monolayer caldarchaeol-PO4 by SAMs appears fewer than monolayers caldarchaeol-PO4 by Langmuir-Blodgett method, the thickness of various from 1 nm to 3 nm.

Preparation and characterization of 3-mercaptopropyl trimethoxysilane self-assembled monolayers

Silane coupling regent （3-mercaptopropyl trimethoxysilane （MPTS）） was prepared on the single-crystal silicon substrate to form 2-dimensional self-assembled monolayers （SAMs）. The growth behavior of SAMs formed from 3-MPTS was investigated using atomic force microscopy （AFM）, contact angle measurements, ellipsometry, and X-ray photoelectron spectroscopy （XPS）. The formation behavior of MPTS SAMs was investigated by a series of AFM images and the roughness of MPTS SAMs on silicon substrates with the assembling time from 1 min to 24 h. The water contact angle measurements indicated the growth behavior of MPTS that correlated with the AFM measurements at different immersion times, too. The chemical states of the typical elements in the MPTS SAMs were analyzed using X-ray photoelectron spectroscopy. The results show that MPTS is self-assembled on the substrate.

Method of Spectrophotometric Microanalysis Based on HRP/PET Self-assembly Film

Horseradish peroxidase monolayer was assembled on the surface of PET-CO2 substrate. The reaction kinetics of HRP/PET film and H2O2 in micro reactor was studied using improved spectrophotometer. The relative activity of self-assembly HRP/PET film still remains above 80% after storing for 150 days at 4℃. When applied to determination of H2O2 in sample, the recoveries of H2O2 are 96.5%~101.1%.

Self Assembled Monolayer Films of C_（60） on O，O＇－Bis（2－aminoethyl）dithiophos Modified Copper

On the surface of O,O'-bis(2-aminoethyl) dithiophosphate modified copper C60forms self-assembled monolayer films (SAMs) through the chemical bond. The film was characterized by contact angle, X-ray photoelectron spectroscopy, electrochemisny, TOF Mass Spetropy.

Fabrication of TiO_2 Thin Film by Electrostatic Self-Assembly Method on Optical Fiber

Anionic surfactant sodium lauryl sulfate(SDS), cationic surfactant palmityl trimethyl ammonium chloride(CTAC) and TiO_2 were used to prepare multilayer films on quartz optic fibers by the electrostatic self-assembly (ESA) method. The whole self-assemble process, the function of surfactant and the effect of TiO_2 slurry′s concentration to the self-assemble were discussed. The isoelectric point of TiO_2 slurry measured by experiment is 6.8. The results show that whatever the concentration of the TiO_2 dispersion, a flat and compact adsorbed monolayer on the optic fiber can be built in a stable dispersion at lower pH. There is a adsorbed equilibrium on the substrate (fiber)/solution interface when enough time of incubation is given. A rough and loosen adsorbed layer is formed on the fiber surface by immersed the substrate in a high pH dispersion (pH>10) because the presence of hydroxyl on particle surface. Film thickness can be controlled by controlling the number of layers in the film.

Cluster-assembled cobalt doped ZnO nanostructured film prepared by low energy cluster beam deposition

Cobalt doped ZnO film assembled by the nanoparticles was prepared by low energy cluster beam deposition.The microstructure,phase structure and optical properties were investigated for the nanostructured films.The results show that the nanostructured film was assembled by monodisperse spherical nanoparticles with average diameter of about 29.3 nm which are distributed uniformly and compactly.The results of X-ray diffraction(XRD)show that cobalt doped ZnO nanostructured film is indexed to a wurtzite structure of ZnO,and no Co-phase structure and other phases are observed.The UV-visible absorption spectra show that the optical band-gap of the film is broadened after doping.

Gold Nanoparticulate Thin Films Fabricated by the Electrostatic Self-Assembly Process

Gold colloids were prepared by citrate-induced reduction of hydrogen tetrachloroaurale, and gold nanoparticles were electrostatically self-assembled with poly( diallyldimethylammonium chloride) into multi-layer thin films on si/icon and quartz substrates. The paniculate thin films were characterized by UV-vis spea-troscopy, surface, enhanced Raman scattering, atomic force microscopy and resistivity measurements. Due to the interparticle coupling between individual gold particles, an obvious collective particle plasmon resonance was ob-served on UV-vis spectra , and the particulate thin films exhibited a strong SERS effect. For multilayer thin films with a high particle coverage on substrates , resistivity of the order of 10-4 Ω·cm was yielded.

6AZO-CONTAINING SELF-ASSEMBLY ULTRA-THIN FILMS AND THEIR PHOTOVOLTAIC PROPERTIES

A kind of azo-containing resin(Azo-R)was synthesized by a simple way through the coupling reaction of 2-nitro-N-methyldiphenylamine-4-diazoresin(NDR)with phenol,and a new covalentely attached multilayer film from Azo-R asH-donor and photosensitive diazoresin,diphenylamine-4-diazoresin(DR)as H-acceptor via H-bonding attraction by self-assembly technique has been fabricated.Following the decomposition of diazonium group of DR under exposure to UVlight,the H-bonds between the layers of the film convert to covalent bonds and the film becomes very stable toward polarsolvents or electrolyte aqueous solutions.Thus the UV-irradiated azo-containing films can be used to measure photocurrentin a conventional three-electrode photoelectrochemical cell using KCl as supporting electrolyte.It was confirmed that theazo-containing multilayer film is responsible for the photocurrent generation.

Fabrication of Au/SiO_(2) Nanocomposite Films by Self-Assembly Multilayer Method

Gold colloid was prepared by chemical reduction of hydrogen tetrachloroaurate, polyelectrolyte/gold nanoparticle/silica nanoparticie composite films were fabricated via an electrostatic self-assembly multilayer method, and composite films of gold nanoparticle dispersed in silica matrix were formed by heat-treating the polyelectrolyte/gold nanoparticle/silica nanoparticle composite films to eliminate the polyelectrolyte. The obtained composite films were investigated with UV-vis, TEM, AFM and XRD. The results show that the self-assembly multilayer method is a promising process to produce composite films of gold nanoparticle-dispersed in organic and/or inorganic matrixes.