A master-slave generalized predictive synchronization control for preheating process of multi-cavity hot runner system

As a key component of injection molding,multi-cavity hot runner(MCHR)system faces the crucial problem of polymer melt filling imbalance among the cavities.The thermal imbalance in the system has been considered as the leading cause.Hence,the solution may rest with the synchronization of those heating processes in MCHR system.This paper proposes a’Master-Slave’generalized predictive synchronization control(MS-GPSC)method with’Mr.Slowest’strategy for preheating stage of MCHR system.The core of the proposed method is choosing the heating process with slowest dynamics as the’Master’to track the setpoint,while the other heating processes are treated as‘Slaves’tracking the output of’Master’.This proposed method is shown to have the good ability of temperature synchronization.The corresponding analysis is conducted on parameters tuning and stability,simulations and experiments show the strategy is effective.

Self-adapting control parameters modifieddifferential evolution for trajectoryplanning of manipulators

Control parameters of original differential evolution （DE） are kept fixed throughout the entire evolutionary process. However, it is not an easy task to properly set control parameters in DE for different optiinization problems. According to the relative position of two different individual vectors selected to generate a difference vector in the searching place, a self-adapting strategy for the scale factor F of the difference vector is proposed. In terms of the convergence status of the target vector in the current population, a self-adapting crossover probability constant CR strategy is proposed. Therefore, good target vectors have a lower CFI while worse target vectors have a large CFI. At the same time, the mutation operator is modified to improve the convergence speed. The performance of these proposed approaches are studied with the use of some benchmark problems and applied to the trajectory planning of a three-joint redundant manipulator. Finally, the experiment results show that the proposed approaches can greatly improve robustness and convergence speed.

Achievement of chaotic synchronization trajectories of master-slave manipulators with feedback control strategy

This paper addresses a master-slave synchro- nization strategy for complex dynamic systems based on feedback control. This strategy is applied to 3-DOF pla- nar manipulators in order to obtain synchronization in such complicated as chaotic motions of end-effectors. A chaotic curve is selected from Duffing equation as the trajectory of master end-effector and a piecewise approximation method is proposed to accurately represent this chaotic trajectory of end-effectors. The dynamical equations of master-slave manipulators with synchronization controller are derived, and the Lyapunov stability theory is used to determine the stability of this controlled synchronization system. In numer- ical experiments, the synchronous motions of end-effectors as well as three joint angles and torques of master-slave manipulators are studied under the control of the proposed synchronization strategy. It is found that the positive gain matrix affects the implementation of synchronization con- trol strategy. This synchronization control strategy proves the synchronization＇s feasibility and controllability for com- plicated motions generated by master-slave manipulators.

A New Self-Adapting Admission Control Algorithm for Differential Service in Web Clusters

A new admission control algorithm considering the network self-similar access characteristics is proposed. Taking advantage of the mathematical model of the network traffic admission control which can effectively overcome the self-similar characteristics of the network requests, through the scheduling of the differential service qucue based on priority while at the same time taking into account various factors including access characteristics of requests, load information, etc, smoothness of the admission control is ensured by the algorithm proposed in this paper. We design a non-linear self-adapting control algorithm by introducing an exponential admission function, thus overcomes the negative aspects introduced by static threshold parameters. Simulation results show that the scheme proposed in this paper can effectively improve the resource utilization of the clusters, while at the same time protecting the service with high priority. Our simulation results also show that this algorithm can improve system stability and reliability too. Key words Web cluster - admission control - differential service - self-similar - self-adapting CLC number TP 393 Foundation item: Supported by the National Natural Science Foundation of China (10375024) and the Hunan Natural Science Foundation of China(03JJY4054)Biography: LIU An-feng(1971-), male, Ph. D candidate, majoring in network computing, Web QoS.

Hierarchical hybrid control network design based on LON and master-slave RS-422/485 protocol

Aiming at the weaknesses of LON bus, combining the coexistence of fieldbus and DCS (Distribu ted Control Systems) in control networks, the authors introduce a hierarchical hybrid control network design based on LON and master slave RS 422/485 protocol. This design adopts LON as the trunk, master slave RS 422/485 control networks are connected to LON as special subnets by dedicated gateways. It is an implementation method for isomerous control network integration. Data management is ranked according to real time requirements for different network data. The core components, such as control network nodes, router and gateway, are detailed in the paper. The design utilizes both communication advantage of LonWorks technology and the more powerful control ability of universal MCUs or PLCs, thus it greatly increases system response speed and performance cost ratio.

BIO-INSPIRED SELF-ADAPTIVE MANUFACTURING SYSTEM CONTROL ARCHITECTURE

Future manufacturing systems need to cope with frequent changes and disturbances, therefore their control architectures require constant adaptability, agility, stability, self-organization, intelligence, and robustness. Bio-inspired manufacturing system can well satisfy these requirements. For this purpose, by referencing the biological organization structure and the mechanism, a bio-inspired manufacturing cell is presented from a novel view, and then a bio-inspired self-adaptive manufacturing model is established based on the ultra-short feedback mechanism of the neuro-endocrine system. A hio-inspired self-adaptive manufacturing system coordinated model is also established based on the neuro-endocrine-immunity system （NEIS）. Finally, an example based on pheromone communication mechanism indicates that the robustness of the whole manufacturing system is improved by bio-inspired technologies.

Self-adaptive PID controller of microwave drying rotary device tuning on-line by genetic algorithms

The control design, based on self-adaptive PID with genetic algorithms(GA) tuning on-line was investigated, for the temperature control of industrial microwave drying rotary device with the multi-layer(IMDRDWM) and with multivariable nonlinear interaction of microwave and materials. The conventional PID control strategy incorporated with optimization GA was put forward to maintain the optimum drying temperature in order to keep the moisture content below 1%, whose adaptation ability included the cost function of optimization GA according to the output change. Simulations on five different industrial process models and practical temperature process control system for selenium-enriched slag drying intensively by using IMDRDWM were carried out systematically, indicating the reliability and effectiveness of control design. The parameters of proposed control design are all on-line implemented without iterative predictive calculations, and the closed-loop system stability is guaranteed, which makes the developed scheme simpler in its synthesis and application, providing the practical guidelines for the control implementation and the parameter design.

Self-adaptive fuzzy controller with formulary rule for servo control of discharge gap in Micro EDM

In micro electrical discharge machining （micro EDM）, it is difficult for servo controlling the narrow discharge gap with the characters of non-linear and quick change. In this paper, aiming at solving the problems above, a self-adaptive fuzzy controller with formulary rule （SAFCFR） is presented based on the dual feedbacks composed by gap electric signal and discharge-ratio statistics. To ensure the properties of self-optimizing and fast stabilization, the formulary rule was designed with a tuning factor. In addition, the fast-convergence algorithms were introduced to adjust control target center and output scale factor. In this way, the normal discharge ratio can tend to the highest value during micro-EDM process. Experimental results show that the proposed algorithms are effective in improving the servo-control performance. According to the drilling-micro-EDM experiments, the machining efficiency is improved by 20% through applying SAFCFR. Moreover, SAFCFR is a prompt way to optimize parameters of discharge-gap servo control.

Variable Parameter Self-Adaptive Control Strategy Based on Driving Condition Identification for Plug-In Hybrid Electric Bus

A variable parameter self-adaptive control strategy based on driving condition identification is proposed to take full advantage of the fuel saving potential of the plug-in hybrid electric bus(PHEB).Firstly,the principal component analysis(PCA)and the fuzzy c-means clustering(FCM)algorithm is used to construct the comprehensive driving cycle,congestion driving cycle,urban driving cycle and suburban driving cycle of Chinese urban buses.Secondly,an improved particle swarm optimization(IPSO)algorithm is proposed,and is used to optimize the control parameters of PHEB under different driving cycles,respectively.Then,the variable parameter self-adaptive control strategy based on driving condition identification is given.Finally,for an actual running vehicle,the driving condition is identified by relevance vector machine(RVM),and the corresponding control parameters are selected to control the vehicle.The simulation results show that the fuel consumption of using the variable parameter self-adaptive control strategy is reduced by 4.2% compared with that of the fixed parameter control strategy,and the feasibility of the variable parameter self-adaptive control strategy is verified.

Research on Master-slave Telerobot Force Telepresence Technology

A 3 DOF master-slave telerobot system is established for study on force telepresence technology. A force feedback and position control scheme is adopted in the bilateral force response control system,and force fidelity and controllability experiments demonstrate feasibility of the con-trol system.

Frequency detection of self-adaption control based on chaotic theory

Low-order Duffing and high-order Rossler chaotic oscillator are connected together and new self-adaption frequency detection method is presented. The frequency difference control between unknown signal and the periodic driving force is realized in this paper and the self-adaption is obtained. Thus, the detection precision and speed are promoted. The limitation that there are too many chaotic oscillators in Duffing system is broken. Meanwhile the disadvantage that the detection speed is lower in R ssler chaotic control is overcome. The self-adaption choice of frequency difference control is realized using the Duffing and Rssler different chaotic oscillators to obtain unknown signal frequency. The simulation results show that the presented method is feasible and effective.

Self-adapting Scalable Differential Evolution Algorithm

Differential evolution(DE) demonstrates good convergence performance,but it is difficult to choose trial vector generation strategies and associated control parameter values.An improved method,self-adapting scalable DE(SSDE) algorithm,is proposed.Trial vector generation strategies and crossover probability are respectively self-adapted by two operators in this algorithm.Meanwhile,to enhance the convergence rate,vectors selected randomly with the optimal fitness values are introduced to guide searching direction.Benchmark problems are used to verify this algorithm.Compared with other well-known DE algorithms,experiment results indicate that this algorithm is better than other DE algorithms in terms of convergence rate and quality of optimization.

Differential Evolution Algorithm Based Self-adaptive Control Strategy for Fed-batch Cultivation of Yeast

In the fed-batch cultivation of Saccharomyces cerevisiae,excessive glucose addition leads to increased ethanol accumulation,which will reduce the efficiency of glucose utilization and inhibit product synthesis.Insufficient glucose addition limits cell growth.To properly regulate glucose feed,a different evolution algorithm based on self-adaptive control strategy was proposed,consisting of three modules(PID,system identification and parameter optimization).Performance of the proposed and conventional PID controllers was validated and compared in simulated and experimental cultivations.In the simulation,cultivation with the self-adaptive control strategy had a more stable glucose feed rate and concentration,more stable ethanol concentration around the set-point(1.0 g·L^(-1)),and final biomass concentration of 34.5 g-DCW·L^(-1),29.2%higher than that with a conventional PID control strategy.In the experiment,the cultivation with the self-adaptive control strategy also had more stable glucose and ethanol concentrations,as well as a final biomass concentration that was 37.4%higher than that using the conventional strategy.

A Self-Adaptive Control Method for Uncertainty Systems Based on ANN with AEP

A self-adaptive control method is proposed based on an artificial neural network(ANN)with accelerated evolutionary programming(AEP)algorithm.The neural network is used to model the uncertainty process,from which the teacher signals are produced online to regulate the parameters of the controller.The accelerated evolutionary programming is used to train the neural network.The experiment results show that the method can obviously improve the dynamic performance of uncertainty systems.

Self-Adaptive QoS Control in Cognitive Networks That Is Based on Service Awareness

This paper analyzes a self-adaptive Quality of Service （QoS） control architecture for cognitive networks （CNs） that is based on intelligent service awareness. In this architecture, packets can be identified and classified using an intelligent service-aware classification model. Drawing on Control Theory, network traffic can be controlled with a self-adaptive QoS control mechanism that has side-road collaboration. In this architecture, perception, analysis, correlation, feedback, decision making, allocation, and implementation QoS mechanisms are created automatically. These mechanisms can adjust resource allocation, adapt to a changeable network environment, optimize end-to-end performance of the network, and ensure QoS.

Study of NURBS Interpolation Algorithm Based on Self-adaptive Control

Aimed at problems such as profile error increasing and acceleration enlarging and tool machine working instability and quality decreasing of workpiece surfaces in processing complicated curved surfaces because of several variable curvatures, an improved method of NURBS interpolation is adopted. According to self-adaptive programming principles, self-adaptive control of profile errors and accelerations and speed-converting is realized with increasing or descending self-adaptive control strategy. This method meets real-time and high-precision requirements of high speed and precision processing, and solves various problems caused by several variable curvatures of a complicated surface.

Unfolding neutron spectra from water-pumping-injection multilayered concentric sphere neutron spectrometer using self-adaptive differential evolution algorithm

A self-adaptive differential evolution neutron spectrum unfolding algorithm(SDENUA)is established in this study to unfold the neutron spectra obtained from a water-pumping-injection multilayered concentric sphere neutron spectrometer(WMNS).Specifically,the neutron fluence bounds are estimated to accelerate the algorithm convergence,and the minimum error between the optimal solution and input neutron counts with relative uncertainties is limited to 10^(-6)to avoid unnecessary calculations.Furthermore,the crossover probability and scaling factor are self-adaptively controlled.FLUKA Monte Carlo is used to simulate the readings of the WMNS under(1)a spectrum of Cf-252 and(2)its spectrum after being moderated,(3)a spectrum used for boron neutron capture therapy,and(4)a reactor spectrum.Subsequently,the measured neutron counts are unfolded using the SDENUA.The uncertainties of the measured neutron count and the response matrix are considered in the SDENUA,which does not require complex parameter tuning or an a priori default spectrum.The results indicate that the solutions of the SDENUA agree better with the IAEA spectra than those of MAXED and GRAVEL in UMG 3.1,and the errors of the final results calculated using the SDENUA are less than 12%.The established SDENUA can be used to unfold spectra from the WMNS.

Design and Simulation of Single Neuron Adaptive PID Controller

The purpose of this paper is to design a neuron adaptive PID controller based on the theory of intelligent control of the extens- ive research on the characteristics of neuronss, neurons and PID controller. Artificial neurons have the adaptive, parallel processing, selflearning learning, and mare fault-tolerant characteristics. When the artificial neurons are used to control the process, the syste^n will enabled to en-sure that the accused has strong anti-interference capability and ro. bustness.

NEW HYDRAULIC ACTUATOR'S POSITION SERVOCONTROL STRATEGY

A new hydraulic actuator-hydraulic muscle （HM） is described, and the actuator＇s features and applications are analyzed, then a position servocontrol system in which HM is main actuator is set up. The mathematical model of the system is built up and several control strategies are discussed. Based on the mathematical model, simulation research and experimental investigation with subsection PID control, neural network self-adaptive PID control and single neuron self-adaptive PID control adopted respectively are carried out, and the results indicate that compared with PID control, neural network self-adaptive PID control and single neuron self-adaptive PID control don＇t need controlled system＇s accurate model and have fast response, high control accuracy and strong robustness, they are very suitable for HM position servo control system.

Harmony search algorithm with differential evolution based control parameter co-evolution and its application in chemical process dynamic optimization

A modified harmony search algorithm with co-evolutional control parameters(DEHS), applied through differential evolution optimization, is proposed. In DEHS, two control parameters, i.e., harmony memory considering rate and pitch adjusting rate, are encoded as a symbiotic individual of an original individual(i.e., harmony vector). Harmony search operators are applied to evolving the original population. DE is applied to co-evolving the symbiotic population based on feedback information from the original population. Thus, with the evolution of the original population in DEHS, the symbiotic population is dynamically and self-adaptively adjusted, and real-time optimum control parameters are obtained. The proposed DEHS algorithm has been applied to various benchmark functions and two typical dynamic optimization problems. The experimental results show that the performance of the proposed algorithm is better than that of other HS variants. Satisfactory results are obtained in the application.