The Magnetic Longitudinal (P-) Wave’s Propagation and Energy Models Underlying the Mechanisms of Its Capacity to Absorb Free Energy

The longitudinal wave term within Faraday’s law of electromagnetic induction (Faraday’s law) underwent recovery to ensure its suitability for theoretical derivation of the equation governing longitudinal electromagnetic (LEM) waves. The revised Maxwell’s equations include the crucial parameters being the attenuation time constants of magnetic vortex potential and electric vortex potential generated by external electromagnetic field within the propagation medium. Specific expressions for them are obtained through theoretical analysis. Subsequently, a model for propagating magnetic P-wave generated by the superposition of a left-handed photo and a right-handed photon in a vacuum is formulated based on reevaluated total current law and revised Faraday’s law, covering wave equations, energy equation, as well as propagation mode involving mutual induction and conversion between scalar magnetic field and vortex electric field. Furthermore, through theoretical derivations centered around magnetic P-wave, evidence was presented regarding its ability to absorb huge free energy through the entangled interaction between zero-point vacuum energy field and the torsion field produced by the vortex electric field.

Maxwell Equations and Magnetic Monopoles

The manuscript introduces an “ab initio” quantum model to deduce the Maxwell equations. After general considerations and laying out the model’s theoretical framework, these equations can be derived alongside a broad variety of other results. Specifically, a corollary of the present model proposes a possible mechanism underlying the formation of magnetic monopoles and allows estimating their formation energy in order of magnitude.

The effect of the guide field on energy conversion during collisionless magnetic reconnection

Magnetic reconnection is well known as an efficient mechanism for transferring magnetic energy into plasma energy.However,how the energy conversion and partition between different species is influenced by the shear angle of the reconnecting magnetic component(i.e.,the guide field strength)is not well understood.Using 2.5-dimensional particle-in-cell simulations,we investigated the energy conversion in reconnection with different guide fields.We found that the overall energy conversion first decreases steeply and then increases slowly when the guide field increases fromB_(g)=0 toB_(g)=4.The increase in energy conversion in the large guide field regime is due to the electron energy gain through the perpendicular channelJ_(⊥)·E_(⊥).The overall energy conversion is predominantly contributed byJ_(⊥)·E_(⊥) rather thanJ||E||.We further find that energy conversion mainly occurs within the reconnection front and the flux pileup region.However,the contribution from the fore reconnection front becomes important in large guide field regimes(3<B_(g)≤4)because of the enhanced electron energy gain.

Room temperature quantum anomalous Hall insulator in honeycomb lattice, RuCS_(3), with large magnetic anisotropy energy

The quantum anomalous Hall(QAH) effect has attracted enormous attention since it can induce topologically protected conducting edge states in an intrinsic insulating material. For practical quantum applications, the main obstacle is the non-existent room temperature QAH systems, especially with both large topological band gap and robust ferromagnetic order. Here, according to first-principles calculations, we predict the realization of the room temperature QAH effect in a two-dimensional(2D) honeycomb lattice, RuCS_(3) with a non-zero Chern number of C = 1. Especially, the nontrivial topology band gap reaches up to 336 me V for RuCS_(3). Moreover, we find that RuCS_(3) has a large magnetic anisotropy energy(2.065 me V) and high Curie temperature(696 K). We further find that the non-trivial topological properties are robust against the biaxial strain. The robust topological and magnetic properties make RuCS_(3) have great applications in room temperature spintronics and nanoelectronics.

Broadband energy harvesting via magnetic coupling between two movable magnets

Harvesting energy from ambient mechanical vibrations by the piezoelectric effect has been proposed for powering microelectromechanical systems and replacing batteries that have a finite life span. A conventional piezoelectric energy harvester （PEH） is usually designed as a linear resonator, and suffers from a narrow operating bandwidth. To achieve broadband energy harvesting, in this paper we introduce a concept and describe the realization of a novel nonlinear PEH. The proposed PEH consists of a primary piezoelectric cantilever beam coupled to an auxiliary piezoelectric cantilever beam through two movable magnets. For predicting the nonlinear response from the proposed PEH, lumped parameter models are established for the two beams. Both simulation and experiment reveal that for the primary beam, the introduction of magnetic coupling can expand the operating bandwidth as well as improve the output voltage. For the auxiliary beam, the magnitude of the output voltage is slightly reduced, but additional output is observed at off-resonance frequencies. Therefore, broadband energy harvesting can be obtained from both the primary beam and the auxiliary beam.

Influence of iron powder content on the electromagnetic and mechanical performance of soft magnetic geopolymer composite

In the induction heating of airport pavement to remove snow and ice,soft magnetic geopolymer composite(SMGC)can be used to gather the dissipated electromagnetic energy,thus enhancing the energy utilization efficiency.The aim of this work is to analyze the influence mechanism of iron powder content on the electromagnetic and mechanical performance of SMGC,so as to provide theoretical guidance for the design of soft magnetic layer within airport pavement structure.The results show that the increase of iron powder content reduces the resistance and magnetoresistance of SMGC by decreasing the content of non-magnetic phases between iron powder.However,the reduction of iron powder spacing also provides a shorter transmission path for the inter-particle eddy currents in the SMGC specimen,which enhances the exchange coupling between iron powder,thus increasing the electromagnetic loss.Therefore,the compatibility between magnetic permeability and electromagnetic loss should be considered comprehensively in the mix design of SMGC.In addition,although iron powder can enhance the mechanical properties of SMGC by improving the density of geopolymer matrix,the excessive amount of iron powder can lead to a weak interfacial transition zone between geopolymer matrix and iron powder.According to the induction heating results,optimized SMGC can improve the energy transfer efficiency of induction heating by 24.03%.

Effect of seed layers on the static and dynamic magnetic properties of CoIr films with negative effective magnetocrystalline anisotropy

The c-axis oriented hcp-Co_(81)Ir_(19)magnetic films were prepared on different seed layers(Ni,Cu,Ir,Pt,Au,and No seed).We systematically investigated the impact that surface-free energy and strain energy have on the orientation and defects and/or internal stress of the grains by increasing the lattice mismatch ratio.Moreover,the initial permeability and the natural resonance frequency were discussed in great detail using a comparison between calculated values and experimental values.We found that the almost unchanged 4πM_(s) andμ_(i) are not affected,while the changed H_(c),intrinsic K_(grain),and f_(r) are strongly dependent on the seed layer and seed layer material.Moreover,the extracted damping constant is sensitive to the defects and/or internal stress and orientation of the grains.Therefore,the soft magnetic properties and microwave properties are adjusted and optimized by seed layers with different materials.

Energy-spread measurement of triple-pulse electron beams based on the magnetic dispersion principle

The method of energy dispersion in magnetic field is used to analyze the energy spread of the triple-pulse electron beam generated by the Dragon-II linear induction accelerator.A sector magnet is applied for energy analysis of the electron beam,with a bending radius of 300 mm and a deflection angle of 90°.For each pulse,the time-resolved and integral images of the electron position at the output port of beam-bending line are recorded by a streak camera and a CCD camera,respectively.Experimental results demonstrate an energy spread of less than ±2.0%for the electron pulses.The cavity voltage waveforms obtained by different detectors are also analyzed for comparison.

Equilibrium folding and unfolding dynamics to reveal detailed free energy landscape of src SH3 protein by magnetic tweezers

Src SH3 protein domain is a typical two-state protein which has been confirmed by research of denaturant-induced unfolding dynamics.Force spectroscopy experiments by optical tweezers and atomic force microscopy have measured the force-dependent unfolding rates with different kinds of pulling geometry.However,the equilibrium folding and unfolding dynamics at constant forces has not been reported.Here,using stable magnetic tweezers,we performed equilibrium folding and unfolding dynamic measurement and force-jump measurement of src SH3 domain with tethering points at its N-and C-termini.From the obtained force-dependent transition rates,a detailed two-state free energy landscape of src SH3 protein is constructed with quantitative information of folding free energy,transition state barrier height and position,which exemplifies the capability of magnetic tweezers to study protein folding and unfolding dynamics.

Generation of Alfvén wave energy during magnetic reconnection in Hall MHD

The effect of the reconnection rate on the generation of Alfvén wave energy is systematically investigated using Hall magnetohydrodynamics（MHD）. It is well known that a decrease in magnetic energy is proportional to the reconnection rate. It is found that an instantaneous increase in Alfvén wave energy in unit Alfvén time is the square dependence on the reconnection rate. The converted Alfvén wave energy is strongly enhanced due to the large increase in the reconnection rate in Hall MHD. For solar-terrestrial plasmas, the maximum converted Alfvén wave energy in unit Alfvén time with the Hall effect can be over 50 times higher than that without the Hall effect during magnetic reconnection.

Development of Magnetic Compound Fluid Rubber Sensor for Practical Usage on &gamma;-Irradiation and Energy Harvesting for Broad-Band Electromagnetic Waves

We have performed sequential studies on new types of soft rubber for their application as artificial skin in robots and haptic sensors. Based on a proposed electrolytic polymerization method and novel adhesion technique for rubber and a metal that utilizes a metal complex hydrate, we have developed an MCF rubber sensor. This sensor uses a magnetic compound fluid (MCF), natural rubber (NR-latex) or chloroprene rubber latex (CR-latex), and requires the application of a magnetic field. The potential application of the developed sensor in various engineering scenarios and our daily lives is significant. In this regard, we investigated the effects of &gamma;-irradiation, infrared radiation, microwaves, and a thermal source on the MCF rubber sensor. We established that the MCF rubber is effective enough to be used for power generation of broadband electro-magnetic waves from &gamma;-rays to microwaves, including the range of the solar spectrum, which is the typical characteristic obtained in the present investigation. The remarkable attribute is that the MCF rubber sensor dose is not degraded by &gamma;-irradiation. We also demonstrated the effectiveness of the MCF rubber sensor in energy harvesting.

Intelligent Fractional-Order Controller for SMES Systems in Renewable Energy-Based Microgrid

An autonomous microgrid that runs on renewable energy sources is presented in this article.It has a supercon-ducting magnetic energy storage(SMES)device,wind energy-producing devices,and an energy storage battery.However,because such microgrids are nonlinear and the energy they create varies with time,controlling and managing the energy inside them is a difficult issue.Fractional-order proportional integral(FOPI)controller is recommended for the current research to enhance a standalone microgrid’s energy management and performance.The suggested dedicated control for the SMES comprises two loops:the outer loop,which uses the FOPI to regulate the DC-link voltage,and the inner loop,responsible for regulating the SMES current,is constructed using the intelligent FOPI(iFOPI).The FOPI+iFOPI parameters are best developed using the dandelion optimizer(DO)approach to achieve the optimum performance.The suggested FOPI+iFOPI controller’s performance is contrasted with a conventional PI controller for variations in wind speed and microgrid load.The optimal FOPI+iFOPI controller manages the voltage and frequency of the load.The behavior of the microgrid as a reaction to step changes in load and wind speed was measured using the proposed controller.MATLAB simulations were used to evaluate the recommended system’s performance.The results of the simulations showed that throughout all interruptions,the recommended microgrid provided the load with AC power with a constant amplitude and frequency.In addition,the required load demand was accurately reduced.Furthermore,the microgrid functioned incredibly well despite SMES and varying wind speeds.Results obtained under identical conditions were compared with and without the best FOPI+iFOPI controller.When utilizing the optimal FOPI+iFOPI controller with SMES,it was found that the microgrid performed better than the microgrid without SMES.

Control of interfacial reaction and defect formation in Gd/Bi_(2)Te_(2.7)Se_(0.3) composites with excellent thermoelectric and magnetocaloric properties

The method to combine thermoelectric(TE)and magnetocaloric(MC)cooling techniques lies in developing a new material that simultaneously possesses a large TE and good MC cooling performance.In this work,using n-type Bi_(2)Te_(2.7)Se_(0.3)(BTS)as the TE base material and Gd as the second-phase MC material,Gd/BTS composites were prepared by the spark plasma sintering method.In the composites,interfacial reaction between Gd and BTS was identified,resulting in the formation of Gd Te,which has a large impact on the electron concentration through the adjustment of defect concentration.The MC/TE composite containing 2.5 wt%Gd exhibited a ZT value of 0.6 at 300 K,essentially retaining the original TE performance,while all the composites largely maintained the excellent MC performance of Gd.This work provides a potential pathway to achieving high performance in MC/TE composites.

Analysis of electron energy distribution function in a magnetically filtered complex plasma

The electron energy distribution function （EEDF） for a magnetically filtered dusty plasma is studied in a dusty double plasma device where the electron energy can be varied from 0.15 eV to ～ 2.8 eV and plasma density from 10 6 cm-3 to 10 9cm-3 . The characteristics of EEDF for these ranges of plasma parameters are investigated in a pristine plasma as well as in a dusty plasma. The results show that in the presence of dust, there is a drastic modification in EEDF patterns in a plasma with higher electron temperature and density than those in a low temperature and low density plasma produced by the magnetic filter.

Relation between stabilization energy, crystal field coefficient and the magnetic exchange interaction for Tb^(3+) ion

Based on a single ion model, Hamiltonian of the simplest form about magnetocrystalline anisotropy for Tb3+ ion was solved by using the numerical method. The relation between the stabilization energy, crystal field coefficient B20 and the magnetic exchange interaction was studied as temperature approaches to 0 K. The results show that the stabilization energy contributed by Tb3+ is linear with crystal field coefficient B20 approximately, but it is insensitive to the change of magnetic exchange interaction for the strong magnetic substances such as TbCo5, Tb2Co17 and Tb2Fe14B compounds.

The Calculation of Ground State Energies of Double-Electron Systems in an Uniform Magnetic Field below 10~9 G

Energies for the ground states of double electron systems in a uniform magnetic field B≤ 10 9 G are calculated by using the modified Slater basis and configuration interaction method, and the result for energy in zero magnetic field is comparable with those obtained by different methods.

Evolution of structure and magnetic properties in PrCo_5 magnet for high energy ball milling in ethanol

High energy ball milling(HEBM) is employed to produce nano-sized grains and particles. In this paper, the structure and magnetic properties are investigated in PrCo5 alloy for HEBM in an ethanol milling medium. With the increase of milling time, the grain size reduces and the coercivity increases. For a milling time of less than 30 min, the hysteresis loop of the aligned sample is very different from that of the un-aligned sample and it does not show a large decrease in magnetization slope, indicating a relatively good alignment of easy axes in particles due to the fact that the texture is nearly well preserved. However, when the milling time is further prolonged, the textured structure deteriorates in the powders.Even though exchange coupling exists between grains within the particle, the magnetic properties are exchange-decoupled between particles and the dipolar interaction results in a negative value of δ m in the whole range of the magnetic field.

A novel transient rotor current control scheme of a doubly-fed induction generator equipped with superconducting magnetic energy storage for voltage and frequency support

A novel transient rotor current control scheme is proposed in this paper for a doubly-fed induction generator（DFIG）equipped with a superconducting magnetic energy storage（SMES） device to enhance its transient voltage and frequency support capacity during grid faults. The SMES connected to the DC-link capacitor of the DFIG is controlled to regulate the transient dc-link voltage so that the whole capacity of the grid side converter（GSC） is dedicated to injecting reactive power to the grid for the transient voltage support. However, the rotor-side converter（RSC） has different control tasks for different periods of the grid fault. Firstly, for Period I, the RSC injects the demagnetizing current to ensure the controllability of the rotor voltage. Then, since the dc stator flux degenerates rapidly in Period II, the required demagnetizing current is low in Period II and the RSC uses the spare capacity to additionally generate the reactive（priority） and active current so that the transient voltage capability is corroborated and the DFIG also positively responds to the system frequency dynamic at the earliest time. Finally, a small amount of demagnetizing current is provided after the fault clearance. Most of the RSC capacity is used to inject the active current to further support the frequency recovery of the system. Simulations are carried out on a simple power system with a wind farm. Comparisons with other commonly used control methods are performed to validate the proposed control method.

A Motor Driven by Permanent Magnets Alone;A Clean and Abundant Source of Electromagnetic Energy from Iron and Other Ferromagnetic Materials

Since the discovery of loadstone more than three hundred years ago, we have contemplated using the magnetic forces generated by permanent magnets to work for us. It is shown here that two permanent magnets with opposite poles facing can attract along their equatorial plane and then repel along their polar plane in sequence, without reversing polarity and without the use of another source of energy. This sequence of attract and repel between two permanent magnets is like the attract and repel sequence between an electromagnet and permanent magnet in an electric motor. The discovery described here can be used to construct a motor driven entirely by permanent magnets.

Shifts in Photon Spectral Power Densities within Schumann (7.7 to 7.8 Hz) Values in Microtubules during Complex Magnetic Field Exposures May Reflect an Information Interface with Universal Energies

The specific diameter of microtubules was shown to be a primary solution when magnetic energy was set equal to Casimir energy. To discern if this spatial containment could be foci for information photon emissions were measured from preparations of microtubules (MTs) while they were exposed in sequential 4 min intervals to various patterns of weak magnetic fields whose intensities ranged from 3 to 10 μT. Calculations from the median mass of a tubulin dimer, its summed charges and the applied magnetic field as well as the change in magnetic moment derived from the energy of the hydrogen line when applied to our experimental fields predicted a dynamic shift (Δf) between 0.03 and 0.21 Hz. Spectral power densities (SPD) indicated marked enhancements in photon numbers during periods of magnetic field exposures within the 7.6 to 7.8 Hz increment. The total SPD units for the shift were 10-18 to 10-17 J per s. Five of the eight patterns elicited a split spectrum of power within this range. Separate factor analyses of the SPDs of the serial values that composed the points of the actual field patterns indicated those that evoked the split-spectrum (Δf = 0.05 to 0.13 Hz) displayed significantly higher loadings on the same factor compared to those that did not. If this shift in photon energy reflects a phase modulation of the coherence frequency (8 MHz) of MTs, the increment of energy per MHz frequency would be within the energy of the neutral hydrogen line. These results suggest that the intrinsic structure or information from specific intensity magnetic fields when applied to MTs is reflected in photon energy densities vacillating around the fundamental Schumann Resonance that could be an interface between Casimir and magnetic sources.