A Design of a PID Self-Tuning Controller Using LabVIEW

In this paper a trial has been made to design a simple self-tuning LabVIEW-based PID controller. The controller uses an open-loop relay test, calculates the tuned parameters in an open loop mode of operation before it updates controller parameters and runs the process as a closed-loop system. The controller reacts on a persistent offset error value as a result of load disturbance or a set point change. Practical results show that such a controller may be recommended to control a variety of industrial processes. A GUI was developed to facilitate control-mode selection, the setting of controller parameters, and the display of control system variables. GUI makes it possible to put the controller in manual or self-tuning mode.

Development of an Enhanced Self-Tuning RBF-PID Controller for Achieving Higher Energy-Efficient Process Control

Proportional, integral and derivative (PID) control strategy has been widely applied in heating systems in decades. To improve the accuracy and the robustness of PID control, self-tuning radial-basis-function neural network PID (RBF-PID) is developed and used. Even though being popular, during the control process both of PID and RBF-PID control strategy are inadequate in achieving simultaneous high energy-efficiency and good control accuracy. To address this problem, in this paper we develop and report an enhanced self-tuning radial-basis-function neural network PID (e-RBF-PID) controller. To identify the superiority of e-RBF-PID, following works are conducted and reported in this paper. Firstly, four controllers, i.e., on-off, PID, RBF-PID and e-RBF-PID are designed. Secondly, in order to test the performance of the e-RBF-PID controller, an experimental water heating system is constructed for being controlled. Finally, the energy consumption for the four controllers under the three control scenarios is investigated through experiments. The experimental results indicate that in the three scenarios, the developed e-RBF-PID controller outperforms on-off controller as having higher accuracy. Compared to the PID controller, the e-RBF-PID controller has higher speed in control, and the experimental results show that settling time savings is between 12.6% - 49.0%. Most importantly, less control energy consumption is obtained if using the e-RBF-PID controller. It is found that up to 28.5% energy consumption can be saved. Therefore, it is concluded that the proposed e-RBF-PID is capable of enhancing energy efficiency during control process.

Fuzzy self-tuning PID control of the operation temperatures in a two-staged membrane separation process

A two-staged membrane separation process for hydrogen recovery from refinery gases is introduced. The principle of the gas membrane separation process and the influence of the operation temperatures are analyzed. As the conventional PID controller is difficult to make the operation temperatures steady, a fuzzy self-tuning PID control algorithm is proposed. The application shows that the algorithm is effective, the operation temperatures of both stages can be controlled steadily, and the operation flexibility and adaptability of the hydrogen recovery unit are enhanced with safety. This study lays a foundation to optimize the control of the membrane separation process and thus ensure the membrane performance.

AUTOMATIC TUNING OF PID CONTROLLERS IN THE THERMAL POWER UNIT LOAD CONTROL SYSTEM

A method of measuring the interactions in a multivariable control sys-tem(MVCS)in time domain is defined in this paper.An intelligent decoupling com-pensator is designed in terms of the concept of fuzzy control,so that the auto-tuningof controllers’ parameters in a 2×2 MVCS can be turned into that of two independentsingle-loop control systems(SLCS).The method presented in the paper has success-fully been used in a simulation experiment on the automatic tuning of a coordinatedcontrol system(CCS)in the drum-boiler turbogenerating unit(DBTU)and the simu-lation results axe satisfactory.

Neural Model-Based Self-Tuning PID Strategy Applied to PEMFC

This paper illustrates the benefits of a self-tuning PID strategy applied to a proton exchange membrane fuel cell system. Controller parameters are updated on-line, at each sampling time, based on an instantaneous linearization of an artificial neural network model of the process and a General Minimum Variance control law. The self-tuning PID scheme allows managing nonlinear behaviors of the system while avoiding heavy computations. The applicability, efficiency and robustness of the proposed control strategy are experimentally confirmed using varying control scenarios. In this aim, the original built-in controller is overridden and the self-tuning PID controller is implemented externally and executed on-line. Experimental results show good performance in setpoint tracking accuracy and robustness against plant/model mismatch. The proposed strategy appears to be a promising alternative to heavy computation nonlinear control strategies and not optimal linear control strategies.

Motion Control of Omnidirectional Mobile Platform based on Fuzzy PID

The omnidirectional mobile platform has three degrees of freedom that make it widely applicable to all areas of industry, while the Mecanum wheel has the disadvantages wheel omnidirectional mobile platform is always difficult in of large vibration, the trajectory precision of Mecanum the omnidirectional mobile platform. To control the trajectory of the omnidirectional mobile platform better, this paper proposes a fuzzy self-tuning PID control model, through establishing the motion model of omnidirectional mobile platform in Adams software, then combined with Simulink simulation, analysis of fuzzy PID controller to improve the accuracy of the speed control of omnidirectional mobile platform, improve the control method of a precise trajectory of the omnidirectional mobile platform motion.

Fuzzy-PID算法在炉温控制中的应用

在工业电炉的控制过程中,由于被控参数具有时变、非线性、不确定等因素,常规PID控制算法难以满足控制要求。本文采用模糊PID算法实现对工业电炉的控制,利用模糊推理在线整定PID控制器的三个参数K_p、K_i、K_d。实际运行结果表明,该控制器取得了较好的快速性和稳定性。

Smith Prediction Monitor AGC System Based on Fuzzy Self-Tuning PID Control

In accordance with the feature of pure delay in monitor AGC system for cold rolling mill, a new fuzzy selftuning PID Smith prediction controller is developed. The position control model is deduced based on a single stand cold rolling mill, and the fuzzy controller for monitor AGC system is designed. The analysis of dynamic performance for traditional PID Smith prediction controller and fuzzy self-tuning PID Smith prediction controller is done by MAT- LAB toolbox. The simulation results show that fuzzy self-tuning PID Smith controller has stronger robustness, faster response and higher static accuracy than traditional PID Smith controller.

Modeling and Simulation of Two Axes Gimbal Using Fuzzy Control

The application of the guided missile seeker is to provide stability to the sensor’s line of sight toward a target by isolating it from the missile motion and vibration.The main objective of this paper is not only to present the physical modeling of two axes gimbal system but also to improve its performance through using fuzzy logic controlling approach.The paper is started by deriving the mathematical model for gimbals motion using Newton’s second law,followed by designing the mechanical parts of model using SOLIDWORKS and converted to xml file to connect dc motors and sensors using MATLAB/SimMechanics.Then,a Mamdani-type fuzzy and a Proportional-Integral-Derivative(PID)controllers were designed using MATLAB software.The performance of both controllers was evaluated and tested for different types of input shapes.The simulation results showed that self-tuning fuzzy controller provides better performance,since no overshoot,small steady-state error and small settling time compared to PID controller.

Simulation Analysis of Control System in an Innovative Magnetically-Saturated Controllable Reactor

Controllable saturation reactors are widely used in reactive power compensation. The control system of controllable saturation reactor determines adaption speed, accuracy, and stability. First, an innovative type of controllable saturation reactor is introduced. After that the control system is designed, and a self-tuning algorithm in PID controller is proposed in the paper. The algorithm tunes PID parameters automatically with different error signals caused by varied loads in power system. Then the feasibility of the above algorithm is verified by Simulink module of Matlab software. The results of simulation indicate that the control system can efficiently reduce adaption time and overshoot.

烘干炉温度集散型智能控制系统设计

烘干炉温度控制工艺复杂,为保证生产过程长期稳定和安全的运行,设计和开发了集散型控制系统,即单片机智能控制器和微机温度控制系统两级集散控制系统。单片机智能控制器以AT89C52单片机为主体,以模糊自适应PID控制算法为控制器,具有处理复杂数据的能力和复杂控制的功能。当微机温度控制系统出现故障时,单片机智能控制器又可作为一个独立的控制系统对烘干炉温度进行控制。实际运行过程表明此系统具有较高的灵活性和可靠性。

Energy Optimization of the Fin/Rudder Roll Stabilization System Based on the Multi-objective Genetic Algorithm （MOGA）

Energy optimization is one of the key problems for ship roll reduction systems in the last decade. According to the nonlinear characteristics of ship motion, the four degrees of freedom nonlinear model of Fin/Rudder roll stabilization can be established. This paper analyzes energy consumption caused by overcoming the resistance and the yaw, which is added to the fin/rudder roll stabilization system as new performance index. In order to achieve the purpose of the roll reduction, ship course keeping and energy optimization, the self-tuning PID controller based on the multi-objective genetic algorithm （MOGA） method is used to optimize performance index. In addition, random weight coefficient is adopted to build a multi-objective genetic algorithm optimization model. The objective function is improved so that the objective function can be normalized to a constant level. Simulation results showed that the control method based on MOGA, compared with the traditional control method, not only improves the efficiency of roll stabilization and yaw control precision, but also optimizes the energy of the system. The proposed methodology can get a better performance at different sea states.

Some Investigations on Fuzzy P+Fuzzy I+Fuzzy D Controller for Non-stationary Process

The paper addresses the adaptive behaviour of parallel fuzzy proportional plus fuzzy integral plus fuzzy derivative (FP+FI+FD) controller. The parallel FP+FI+FD controller is actually a non-linear adaptive controller whose gain changes continuously with output of the process under control. Two non-stationary processes, whose characteristics change with time, are considered for simulation study. Simulation is performed using software LabVIEW TM . The set-point tracking response of parallel FP+FI+FD is compared with conventional parallel proportional plus integral plus derivative (PID) controller, tuned with the Ziegler-Nichols (Z-N) tuning technique. Simulation results show that conventional PID controller fails to track the set-point and becomes unstable as the process changes its characteristic with time. But the parallel FP+FI+FD controller shows considerably much better set-point tracking response and does not deviate from steady state. Also, a huge spike is observed in the output of PID controller as the reference set-point and process parameters are changed, while the FP+FI+FD controller gives spike free control signal.