Investigation of the interaction between NS-DBD plasma-induced vortexes and separated flow over a swept wing

The effect of nanosecond pulsed dielectric barrier discharge(NS-DBD) plasma flow separation control is closely related to the actuation frequency,because it involves the interaction between plasma-induced vortexes and separated flow.In order to study the mechanism of NS-DBD plasma flow separation control over a swept wing,especially the influence of the actuation frequency,at first,experimental studies of the actuation frequencies at 100 Hz are conducted to validate the numerical simulation method.Then,numerical studies of different actuation frequencies which are 50 Hz,100 Hz,160 Hz,200 Hz,500 Hz,and 1000 Hz,respectively are conducted.The interaction between the plasma-induced vortexes and the separated flow is analyzed.Results show that there is a range of the actuation frequency which includes the frequency(160 Hz) calculated by the average aerodynamic chord length to make the control effect good,but when the actuation frequencies are too low(50 Hz) or too high(1000 Hz),the control effect will get worse.The former is because plasmainduced vortexes disappear in a period within an actuation cycle;the latter is because plasma-induced vortexes cannot develop completely,resulting in a weak vortex intensity.

Analysis and experimental study on resistance-increasing behavior of composite high efficiency autonomous inflow control device

Bottom water coning is the main reason to reduce the recovery of horizontal bottom water reservoir. By water coning, we mean the oil-water interface changes from a horizontal state to a mound-shaped cone and breaks through to the wellbore. Autonomous inflow control device(AICD) is an important instrument maintain normal production after bottom water coning, however, the resistance increasing ability of the swirl type AICD is insufficient at present, which seriously affects the water control effect. Aiming this problem, this paper designs a multi-stage resistance-increasing and composite type AICD. The separation mechanism of oil-water two phases in this structure, the resistance form of oil-water single phase and the resistance-increasing principle of water phase are analyzed. Establishing the dual-phase multi-stage separation and resistance-increasing model, and verified by measuring the throttling pressure drop and oil-water volume fraction of the AICD, it is found that the composite type AICD has the effect of ICD and AICD at the same time, which can balance the production rate of each well section at the initial stage of production, delay the occurrence of bottom water coning. In the middle and later stages of production, water-blocking can be effectively increased to achieve water control and stable production.After structural sensitivity analysis, the influence law of various structural parameters on the water control performance of composite AICD was obtained. The simulation calculation results show that,compared with the existing swirl type AICD, composite AICD has higher sensitivity to moisture content,the water phase throttling pressure drop is increased by 4.5 times on average. The composite AICD is suitable for the entire stage of horizontal well production.

Comparative assessment of SAS and DES turbulence modeling for massively separated flows

Numerical studies of the flow past a circular cylinder at Reynolds number 1.4 × 105 and NACA0021 airfoil at the angle of attack 60° have been carried out by scale-adaptive simulation （SAS） and detached eddy simu- lation （DES）, in comparison with the existing experimental data. The new version of the model developed by Egorov and Menter is assessed, and advantages and disadvantages of the SAS simulation are analyzed in detail to provide guidance for industrial application in the future. Moreover, the mechanism of the scale-adaptive characteristics in separated regions is discussed, which is obscure in previous analyses. It is con- cluded that： the mean flow properties satisfactorily agree with the experimental results for the SAS simulation, although the prediction of the second order turbulent statistics in the near wake region is just reasonable. The SAS model can produce a larger magnitude of the turbulent kinetic energy in the recir- culation bubble, and, consequently, a smaller recirculation region and a more rapid recovery of the mean velocity out- side the recirculation region than the DES approach with the same grid resolution. The vortex shedding is slightly less irregular with the SAS model than with the DES approach, probably due to the higher dissipation of the SAS simulation under the condition of the coarse mesh.

Applications of URANS on predicting unsteady turbulent separated flows

Accurate prediction of unsteady separated turbulent flows remains one of the toughest tasks and a practi cal challenge for turbulence modeling. In this paper, a 2D flow past a circular cylinder at Reynolds number 3,900 is numerically investigated by using the technique of unsteady RANS （URANS）. Some typical linear and nonlinear eddy viscosity turbulence models （LEVM and NLEVM） and a quadratic explicit algebraic stress model （EASM） are evaluated. Numerical results have shown that a high-performance cubic NLEVM, such as CLS, are superior to the others in simulating turbulent separated flows with unsteady vortex shedding.

INVESTIGATION OF PULSED-WIRE TECHNIQUE FOR WALL PARAMETERS MEASUREMENT IN SEPARATED FLOWS

A pulsed-wire wall probe measurement system was developed in this paper,which can be used for measuring wall Parameters in separated flow- The operating princi-ple was described and the way of probe calibration was given. Wall parameters of back-ward-facing and forward-facing step flow were measured,and the wall nows structure andcharacters were revealed.

TURBULENT SEPARATED REATTACHED FLOW IN A TWO-DIMENSIONAL CURVED-WALL DIFFUSER

A turbulent separation-rcattachment flow in a two-dimensional asymmetrical curved-wall diffuser is studied by a two-dimensional laser doppler velocimeter.The turbulent boundary layer separates on the lower curved wall under strong pressure gradient and then reattaches on a parallel channel.At the inlet of the diffuser,Reynolds number based on the diffuser height is 1.2×10~5 and the velocity is 25.2m/s.The re- sults of experiments are presented and analyzed in new defined streamline-aligned coordinates.The experiment shows that after Transitory Detachment Reynolds shear stress is negative in the near-wall backflow region. Their characteristics are approximately the same as in simple turbulent shear layers near the maximum Reynolds shear stress.A scale is formed using the maximum Reynolds shear stresses.It is found that a Reynolds shear stress similarity exists from separation to reattachment and the Schofield-Perry velocity law ex- ists in the forward shear flow.Both profiles are used in the experimental work that leads to the design of a new eddy-viscosity model.The length scale is taken from that developed by Schofield and Perry.The composite velocity scale is formed by the maximum Reynolds shear stress and the Schofield Perry velocity scale as well as the edge velocity of the boundary layer.The results of these experiments are presented in this paper

Numerical Simulation and Experimental Investigation of 3 D Separated Flow Field around a Blunt Body

To study the effects of factors such as electromagnetic field and electron temperature on the ion extraction characteristics (extraction time, collision loss ratio) in atomic vapor laser isotope separation (AVLIS), 2 D electron equilibrium model was used to analyze and simulate the ion extraction process. The collisions between particles mainly considered charge exchanges between isotopic ions and atoms, which were treated by using cross section. The results show that the electric field and electron temperature have significant effects on the ion extraction characteristics: the stronger the electric field is, the higher the electron temperature is; the shorter the extraction time is, the less the collision loss ratio is, and moderate constant magnetic field has few effects on them. Key words atomic vapor laser isotope separation (AVLIS); ion extraction; charge exchange cross section; collision loss ratio

SEPARATED FLOW AROUND BENT-NOSE BICONIC IN HYPERSONIC FLOW

This article investigates the separated flow around the bent-nose biconic, in which the second ordered TVD(Total Variation Diminishing) method is applied. The governing cqua-tion is a thin layer Navier-Stokes equation. The surface pressure distribution at the leeward side is a little higher in the vicinity of the symmetrical plane. This seems to be caused by the development of the vortex at the leeward side due to the separated flow. The location of a separation line and the size are in very good agreement with the experiment. Also the secondary separation is captured very clearly.

Investigation of Separated Flow around a Curved Air Intake

This paper prcsents an investigation of two-dimensional separated flow in and around a submerged curved intake by experiment and computation. The eniptic Navier-Stokes equations are employed which are discreted in body-fitted coordinate system by the SIMPLE method. The results show that the flow separation exists near and behind the inlet and the duct flow is distorted. Comparison between the computational and experimental data is fairly satisfactory.

FLUID DYNAMICS IN A GAS-STIRRED LADLE——A Separated Flow Model with Stochastical Trajectories

A separated flow model with stochastical trajectories has been developed to describe the fluid flow in a bubble stirred ladle.The bubble dispersion,turbulent characteristics and gas-liquid interactions can be predicted by this mathematical model.The bubble flow as a dispersed phase is treated in a Lagrangian frame of reference and the analysis of the turbulent flow for liquid phase is conducted in a Eulerian field.The interactions between bubbles and liquid phases are considered as a bubble source term in the control equation for a continuous phase. The Monte Carlo sampling method is used to determine the bubble trajectories.The homoge- neous flow model is also taken into consideration so that it can be compared with the sepa- rated flow model.Numerical predictions using a water model of a ladle show that the pre- dicted results of the separated flow model agree satisfactorily with the experimental results, but the prediction of the homogeneous flow model are not in good agreement with the experi- mental results.

NATURE OF THE SURFACE HEAT TRANSFER FLUCTUATION IN A HYPERSONIC SEPARATED TURBULENT FLOW

This paper presents the results of an experimental study of the unsteady nature of a hypersonic sepa- rated turbulent flow.The nominal test conditions were a freestream Mach number of 7.8 and a unit Reynolds number of 3.5x10^7/m.The separated flow was generated using finite span forward facing steps.An array of flush mounted high spatial resolution and fast response platinum film resistance thermometers was used to make mul- ti-channel measurements of the fluctuating surface heat trtansfer within the separated flow.Conditional sampling ana- lysis of the signals shows that the root of separation shock wave consists of a series of compression wave extending over a streamwise length about one half of the incoming boundary layer thickness.The compression waves con- verge into a single leading shock beyond the boundary layer.The shock structure is unsteady and undergoes large-scale motion in the streamwise direction.The length scale of the motion is about 22 percent of the upstream influence length of the separation shock wave.There exists a wide band of frequency of oscillations of the shock system.Most of the frequencies are in the range of 1-3 kHz.The heat transfer fluctuates intermittently between the undisturbed level and the disturbed level within the range of motion of the separation shock wave.This inter mittent phenomenon is considered as the consequence of the large-scale shock system oscillations.Downstream of the range of shock wave motion there is a separated region where the flow experiences continuous compression and no intermittency phenomenon is observed.

NUMERICAL SOLUTION OF NAVIER-STOKES EQUATION OF UNSTEADY SEPARATED FLOWS DUE TO A SPOILER'S OSCILLATION

The finite difference method (FDM) is applied in the present paper to solve the unsteady NHS equations for incompressible fluids. ADI and SLOR methods are served for the vorticity equation and the Poisson equation for ψ respectively. The upwind scheme is used for the convective terms. The moving boundary conditions are specially treated, and the effects of outlet conditions on the flow field are abo examined. Numerical results obtained show that the spoiler's oscillation induces forming, growing and shedding of the vortices. The shedding frequency of vortices is equal to that of the spoiler's oscillation. The forced unsteady separated flows under the present investigation depend mainly on the reduced frequency. At low reduced frequency, the vortices shed from the spoiler interact weakly with each other, and move downstream at an almost uniform speed of 038 V∞. At high reduced frequency, the interaction between the adjacent vortices strengthens. They close up to and rotate around each other, and eventually, merge into one vortex.

Effect of leading-edge tubercles on the flow over low-aspect-ratio wings at low Reynolds number

Two-dimensional time-resolved particle image velocimetry(TR-PIV)and stereographic particle image velocimetry(SPIV)techniques were used to investigate the effect of leading-edge tubercles on the flow over low-aspect-ratio wing models.The angle of attack is fixed at 10°,and the Reynolds number based on chord length is 5.8×10^(3).It is shown that the leading-edge tubercles can effectively mitigate flow separation in the model and also reduce the contribution of wake vortex to the fluctuating energy of flow.Counter-rotating vortex pairs(CVPs)initiated from the peak of leading-edge tubercles can promote nearby momentum exchange,enhance mixing of the flow and increase the energy contained in the boundary layer,which results in resisting the larger adverse pressure gradient.Therefore,it is concluded that CVPs play an important role in mitigating the flow separation for wings with leading-edge tubercles.

Numerical Studies on Flow Fields Around Buildings in an Urban Street Canyon and Cross-Road

The questions on how vortices are constructed and on the relationship between the flow patterns and concentration distributions in real street canyons are the most pressing questions in pollution control studies. In this paper, the very large eddy simulation (VLES) and large eddy simulation (LES) are applied to calculate the flow and pollutant concentration fields in an urban street canyon and a cross-road respectively. It is found that the flow separations are not only related to the canyon aspect ratios, but also with the flow velocities and wall temperatures. And the turbulent dispersions are so strongly affected by the flow fields that the pollutant concentration distributions can be distinguished from the different aspect ratios, flow velocities and wall temperatures.

Serpentine Inlet Performance Enhancement Using Vortex Generator Based Flow Control

In order to provide the line-of-sight blockage of the engine face for an advanced Uninhabited Combat Air Vehicle（UCAV）, a highly curved serpentine inlet is proposed and experimentally studied. Based on the static pressure distribution measurement along the wall, the flow separation is found at the top wall of the second S duct for the baseline inlet design, which yields a high flow distortion at the exit plane. To improve the flow uniformity, a single array of vortex generators （VGs） is employed within the inlet. In this experimental study, the effects of mass flow ratio, free stream Mach number, angle of attack and yaw on the performance of a serpentine inlet instrumented with VGs are obtained. Results indicate： （1） Compared with the baseline serpentine design without flow control, the application of the VGs promotes the mixing of core flow and the low momentum flow in the boundary layer and thus prevents the flow separation. Under the design condition, the exit flow distortion （-↑△σ0） decreases from 11.7% to 2.3% by using the VGs. （2） With the descent of the free stream Mach number the total pressure loss decreases. However, the circular total pressure distortion increases. When the angle of attack rises from - 4° to 8°, the total pressure recovery and the circular total pressure distortion both go down. In addition, with the increase of yaw the total pressure recovery is fairly constant, while the circular total pressure distortion ascends gradually. （3） When Mao = 0.6-0.8, a = -4°-8° and β = 0°-6°, the total pressure recovery varies between 0.936 and 0. 961, the circular total pressure distortion coefficient varies between 1.4 % and 5.4 % and the synthesis distortion coefficient has a ranges from 3.8 % to 7.0 %. The experimental results confirm the excellent performance of the newly designed serpentine inlet incorporating VGs.

VORTEX CONTROL BY THE SPANWISE SUCTION FLOW ON THE UPPER SURFACE OF DELTA WING

The numerical investigation has been performed to explore the feasibility of vortex control by leading edge sucking excitation on a delta wing. The results reveal that the flow on the upper surface of the delta wing changes significantly in a wide range of the angle of attack. For the vortical flow at moderate angle of attack, the secondary and tertiary vortices are weakened or suppressed, and the total lift is almost unchanged. For the stalled flow at high angle of attack, the leading edge concentrated vortex is recovered, and the lift is enhanced with increasing suction rate. For the bluff-body flow at even high angles of attack, the lift can still be improved. The concentrated vortex disappears on the upper surface, and the load increment is nearly unchanged along the chordwise direction.

Performance Optimization of Torque Converters Based on Modified 1D Flow Model

A methodology for performance optimization of torque converters is put forward based on the one-dimensional (1D) flow model. It is found that the inaccuracy of 1D flow model for predicting hydraulic performance at the low speed ratio is mainly caused by the separation phenomenon at the stator cascade which is induced by large flow impinging at the pressure side of the stator blades. A semi-empirical separation model is presented and incorporated to the original 1D flow model. It is illustrated that the improved model is able to predict the circumferential velocity components accurately, which can be applied to performance optimization. Then, the Pareto front is obtained by using the genetic algorithm (GA) in order to inspect the coupled relationship among stalling impeller torque capacity, stalling torque ratio and efficiency. The efficiency is maximized on the premise that a target stalling impeller torque capacity and torque ratio are achieved. Finally, the optimized result is verified by the computational fluid dynamics(CFD) simulation, which indicates that the maximal efficiency is increased by 0.96%.

In uence of Endwall Boundary Layer Suction on the Flow Fields of a Critically Loaded Di usion Cascade

Boundary layer suction is an e ective method used to delay separations in axial compressors. Most studies on bound?ary layer suction have focused on improving the performance of compressors,whereas few studies investigated the influence on details of the flow fields,especially vortexes in compressors. CFD method is validated with experi?mental data firstly. Three single?slot and one double?slot endwall boundary layer suction schemes are designed and investigated. In addition to the investigation of aerodynamic performance of the cascades with and without suction,variations in corner open separation,passage vortex,and concentration shedding vortex,which are rarely seen for the flow controlled blades in published literatures,are analyzed. Then,flow models,which are the ultimate aim,of both baseline and aspirated cascades are established. Results show that single?slot endwall suction scheme adjacent to the suction surface can e ectively remove the corner open separation. With suction mass flow rate of 0.85%,the overall loss coe cient and endwall loss coe cient of the cascade are reduced by 25.2% and 48.6%,respectively. Besides,this scheme increases the static pressure rise coe cient of the cascade by 3.2% and the flow turning angle of up to 3.3° at 90% span. The concentration shedding vortex decreases,whereas the passage vortex increases. For single?slot suction schemes near the middle pitchwise of the passage,the concentration shedding vortex increases and the passage vortex is divided into two smaller passage vortexes,which converge into a single?passage vortex near the trailing edge section of the cascade. For the double?slot suction scheme,triple?passage vortexes are presented in the blade passage. Some new vortex structures are discovered,and the novel flow models of aspirated compressor cascade are proposed,which are important to improve the design of multi?stage aspirated compressors.

VISCOUS-INVISCID INTERACTING FLOW THEORY

In this paper a viscous-inviscid interacting flow theory(IFT)is developed for an incompressible, two-dimensional laminar flow.IFT's main points are as follows.(1)By introducing a concept of interaction lay- er where the normal momentum exchange is dominating,a new three layer structure is established.(2)Through the conventional manipulations and by introducing an interaction model,both the streamwise and normal length scales are proved to be functions of a single parameter m,which is related to the streamwise pressure gradient and Reynolds number.(3)The approximate equations governing the flow of each layer as well as the whole interaction flow are derived.The present IFT is applicable to both attached and attached-separation bubble-reattached flows, The classical boundary layer theory and Triple-deck theory are shown to be two special cases of the present theory under m=0 and 1/4,respectively.Furthermore IFT provides new distinctions of both the normal and streamwise length scales for flow-field numerical computation and also gives a new approach to developing the simpli- fied Navier-Stokes(SNS)equations.

Flow control of micro-ramps on supersonic forward-facing step flow

The effects of the micro-ramps on supersonic turbulent flow over a forward-facing step（FFS） was experimentally investigated in a supersonic low-noise wind tunnel at Mach number 3 using nano-tracer planar laser scattering（NPLS）and particle image velocimetry（PIV） techniques. High spatiotemporal resolution images and velocity fields of supersonic flow over the testing model were captured. The fine structures and their spatial evolutionary characteristics without and with the micro-ramps were revealed and compared. The large-scale structures generated by the micro-ramps can survive the downstream FFS flowfield. The micro-ramps control on the flow separation and the separation shock unsteadiness was investigated by PIV results. With the micro-ramps, the reduction in the range of the reversal flow zone in streamwise direction is 50% and the turbulence intensity is also reduced. Moreover, the reduction in the average separated region and in separation shock unsteadiness are 47% and 26%, respectively. The results indicate that the micro-ramps are effective in reducing the flow separation and the separation shock unsteadiness.