基于DCS-惯性权重组合的柔性机械臂运动轨迹控制系统研究

为了有效调控机械臂运动幅度,避免柔性机械臂实际运动轨迹与目标轨迹发生较大的偏差,设计一种基于分散控制系统(DCS)-惯性权重组合的柔性机械臂运动轨迹控制系统,它是一个集合了计算机、通信、显示和控制的计算机系统,该系统由过程控制和过程监控。通过DCS算法控制监测对象行为幅度并计算柔性机械臂惯性权重,利用DCS-惯性权重组合求解素数控制指标的具体数值,实现了对柔性机械臂运动轨迹控制系统的软件设计。实验结果表明,DCS-惯性权重组合算法作用下的机械臂末端坐标在横轴、纵轴、空间轴方向上的运动幅值均可以被控制在10个单位长度之内,并且在0.52 s内进入机械臂运动轨迹最佳控制状态,运动轨迹差值最大仅为0.01 rad,验证了该系统具备可行性和有效性。

基于模糊BP神经网络的智能轮椅BLDCM控制

现阶段多数轮椅电机仍使用传统PID控制,该控制方式存在控制精准度较低、超调量较大以及抗扰动能力差等问题。为解决以上问题,通过对无刷直流电机进行研究,在分析了其控制方法后,提出一种基于模糊BP神经网络的BLDCM控制方法。首先,研究了BLDCM结构并搭建数学模型。其次,在模型基础上构建了模糊BP神经网络PID控制器。最后,在Matlab/Simulink中搭建整个电机控制系统进行三种不同工况下的运动控制仿真,并与传统PID控制算法进行对比。实验结果表明:模糊BP神经网络PID控制策略能获得更好的PID控制参数,具有良好的抗扰动能力,有效的改善了整个轮椅控制系统的动态性能。

永磁同步电机双向DC/DC变换器混合储能设计

为了提高永磁同步电机的发电效率,设计一种永磁同步电机双向DC/DC变换器混合储能方案,并开展性能仿真分析。利用双向DC/DC变换器连接储能部件与负载母线,该变换器的控制性能对系统整体动/静态性能存在明显影响。研究结果表明:在Buck模式下仿真测试得到,双向DC/DC变换器高压侧电流逐渐升高,产生了持续上升的最高输出功率。双向DC/DC变换器与Buck电路达到了合理的参数,能够达到混合储能系统要求达到的稳定性与快速性控制标准。本设计的双向DC/DC变换器主电路与Boost电路各项参数处于较优的状态,能够实现对混合储能系统进行稳定高效控制的目标。电感与电容值满足系统运行要求,可以实现双向DC/DC变换器的快速响应,能够快速控制电流值,并获得稳定的电压参数,能够满足优异的动态调控性能。

基于参数自整定模糊PID的BLDC控制研究

为解决传统PID控制在无刷直流电机调速系统中的控制精度低、效果不佳等问题,设计了一种基于参数自整定模糊PID控制的调速系统。通过在Matlab/Simulink仿真软件中建立了无刷直流调速系统的模型,分别采用传统PID控制、模糊PID控制和参数自整定模糊PID控制来对转速环进行调控,而电流环则采用PID控制。通过对比研究结果发现,采用参数自整定模糊PID控制的调速系统具有许多优势。系统的超调量较小,控制效果较好,同时提高了系统的鲁棒性。通过搭建模型并进行仿真实验,证明了采用参数自整定模糊PID控制的调速系统在解决无刷直流电机调速系统控制精度低、效果不佳等问题方面具有优势。这一方法能够有效提升系统的控制性能,并增强系统的鲁棒性。该无刷直流电机的调速系统可以稳定、可靠运行,满足使用需求。

基于田口法多目标优化BLDCM

为了解决高效多目标优化电机输出性能的问题,采用田口法优化算法,以BLDCM为例,以初始设计参数为基础,按电机的输出转矩、转矩脉动和铁损作为待优化性能指标,设计了优化目标函数。将定子内径、槽深、槽开口、齿宽和气隙等关键结构参数设为优化变量,设计了正交试验,通过计算信噪比响应值并结合敏感性分析,筛选出稳定且满足设计要求的参数组合,确定最优的优化参数方案。针对优化前后的目标参数变化用有限元进行分析,证明该方法的合理性。

开绕组BLDCM直接转矩控制电压矢量特性研究

基于直接转矩控制(DTC)的开绕组无刷直流电机(BLDCM)具有运行效率高、电压矢量多样、控制结构简单等优点,适用于工业领域。根据共直流母线开绕组BLDCM控制拓扑搭建了相应的数学模型,对该拓扑下电压矢量的特性进行理论分析及分类,并将电压幅值不为零的电压矢量分为大、中、小三类。分析结果表明:在相同的运行条件下,大矢量作用下转矩变化率最大,小矢量作用下转矩变化率最小,中矢量居于两者之间。仿真结果验证了理论分析的正确性和控制方法的可行性。

New Method to Restrain Pumping Voltage of Braking Procedure for Brushless DC Motor of Electric Armored Vehicle

In order to restrain the high pumping voltage of braking procedure which is harmful to the system of electric armored vehicle. Based on the analysis of pumping voltage of the braking procedure, the relation between pumping voltage and PWM ratio is derived and a new digital control method to restrain the pumping voltage by changing PWM ratio is put forward. Because the capacitance is decreased effectively, the volume of controller is reduced and the performance to price ratio is improved. The results of computer simulation and experiment proved that this method is feasible and valid.

Simulation Research of Fault Model of Detecting Rotor Dynamic Eccentricity in Brushless DC Motor Based on Motor Current Signature Analysis

基于Ansoft／Maxwell设置动态偏心故障，建立求解电机电感和磁链的有限元模型，通过仿真，证明了将感应电机动态偏心故障的特征频率经过简化后，同样适用于无刷直流电动机。基于Ansoft／Simplorer建立无刷直流电动机系统的仿真模型。在电机稳态运行下，对定子电流进行傅里叶分析，研究并建立基于定子电流监测动态偏心故障的仿真模型：动态偏心故障与特征频率的关系、动态偏心故障程度与特征频率幅值的关系。进而研究了无刷直流电动机稳态运行时转速波动对偏心故障监测的影响。仿真结果表明，转子偏心程度加大，特征频率的幅值增加。

Anti-reverse rotation startup method for sensorless brushless DC motor

In order to start up the brushless DC motor （BLDCM） without reverse rotation and smoothly switch the running state of the motor, a novel startup and smoothly switching method for a sensodess BLDCM is presented. Based on the saturation effect of the stator iron, six short voltage pulses are applied to determine the initial rotor position and the rotor can be found within 60°. After that, a series of short and long voltage pulses are used to accelerate the motor and the variation of the response current is utilized to detect the rotor position dynamically. When the motor reaches a certain speed at which the back-electromotive force （EMF） method can be applied, all the power devices are turned off and the running state of the motor is smoothly switched at the moment determined by the relationship between the terminal voltage waveform and the commutation phases. The experimental results verify the feasibility and validity of the proposed method.

EFFECTIVE DOUBLE LOOP CONTROL FOR A SQUARE WAVE BRUSHLESS DC MOTOR

A new type of brushless DC motor has been developed by using a square wave rare earth permanent magnet synchronous motor with its double loop control circuit. The double loop control scheme of the drive system yields a combination of desired characteristics including simplified control structure, small ripple torque, high speed accuracy, wide operating speed range, and fast dynamic response. Experimental results confirm excellent characteristics of the motor.

直流微网储能DC/DC变换器的自适应虚拟直流电机控制

电力电子化的直流微电网自身缺乏惯性,当功率发生波动时,直流母线电压会产生较大突变,不利于其稳定运行。为了解决这一问题,虚拟直流电机控制被应用于直流变换器中来模拟直流电机的外特性,进而为直流微电网提供惯性支撑。但传统参数固定的虚拟直流电机控制在提供惯性的同时会牺牲系统的动态响应速度。针对这一问题,提出了参数自适应虚拟直流电机控制,并将它应用于储能端推挽式DC/DC变换器中。建立了系统的小信号模型,分析了转动惯量参数变化对系统的影响,并给出了参数的自适应调节原则。最后,搭建了仿真模型对不同控制方法进行了对比分析。仿真结果表明所提控制策略在为系统提供较大惯性支撑的同时,系统仍具有较快的动态响应速度。

Improved single-neuron PID controller for DC motor applied in robot system

An improved single-neuron proportional integral derivative （ PID ） controller and a new method to build the DC motor system were presented in the article. In the simulation, the robot arm is considered as an external load to DC motor. Both the motor module and the load module are crea- ted in Simulink to achieve simulation results closer to real robot system. In this way, it can well veri- fy the performance of the improved single-neuron PID controller, which is a combined controller of normal PID controller and single-neuron PID controller. Besides, an intelligent switcher can help to realize the function of choosing a better control algorithm according to motor＇ s velocity output. Sim- ulated results confirm the rapid and stable response of the improved PID controller. Moreover, the improved single-neuron PID controller has an excellent ability to overcome the load impact and su- press the jamming signals. At last, a GUI interface platform is built to make the controller easier to be applied in other robot systems.

Robust Control Strategy for the Speed Control of Brushless DC Motor

Brushless DC motor ( BLDCM) speed servo system is multivariable,nonlinear and strong coupling. The parameter variation, the cogging torque and the load disturbance easily influence its performance. Therefore,it is difficult to achieve superior performance by using the conventional PID controller. To solve the deficiency,the paper represents the algorithm of active-disturbance rejection control ( ADRC) based on back-propagation ( BP) neural network. The ADRC is independent on accurate system and its extended-state observer can estimate the disturbance of the system accurately. However,the parameters of Nonlinear Feedback ( NF) in ADRC are difficult to obtain. So in this paper,these parameters are self-turned by the BP neural network. The simulation and experiment results indicate that the ADRC based on BP neural network can improve the performances of the servo system in rapidity,control accuracy,adaptability and robustness.

Fuzzy PID Controllers Using FPGA Technique for Real Time DC Motor Speed Control

The design of intelligent control systems has become an area of intense research interest. The development of an effective methodology for the design of such control systems undoubtedly requires the synthesis of many concepts from artificial intelligence. The most commonly used controller in the industry field is the proportional-plus-integral-plus-derivative (PID) controller. Fuzzy logic controller (FLC) provides an alternative to PID controller, especially when the available system models are inexact or unavailable. Also rapid advances in digital technologies have given designers the option of implementing controllers using Field Programmable Gate Array (FPGA) which depends on parallel programming. This method has many advantages over classical microprocessors. In this research, A model of the fuzzy PID control system is implemented in real time with a Xilinx FPGA (Spartan-3A, Xilinx Company, 2007). It is introduced to maintain a constant speed to when the load varies.,The model of a DC motor is considered as a second order system with load variation as a an example for complex model systems. For comparison purpose, two widely used controllers “PID and Fuzzy” have been implemented in the same FPGA card to examine the performance of the proposed system. These controllers have been tested using Matlab/Simulink program under speed and load variation conditions. The controllers were implemented to run the motor as real time application under speed and load variation conditions and showed the superiority of Fuzzy-PID.

Comparative Study between the PID Regulator and the Fuzzy Regulator Applied to the Operation of a Brushless DC Motor

This paper presents the results of research on speed regulation of a brushless DC motor. This is mainly a comparative study between a PID regulator and a fuzzy regulator applied to the operation of this type of engine in order to find the best control. The BLDC engine must operate under various speed and load conditions with improved performance and robust and complex speed control. Because of this complexity, the traditional PID command encounters difficulties in controlling the speed of a BLDC. Another control technique is currently developing and is producing good results. This is the fuzzy controller that handles process control problems, that is, managing a process based on a given set point per action on the variables that describe the process. To achieve the desired results, the brushless DC machine model will be studied. With the model obtained, both types of regulator will be tested. A synthesis of the observed comparison results will enable a conclusion to be drawn on the performance of the two types of regulators driving a BLDC (Brushless DC).

Steering Control of Wheeled Armored Vehicle with Brushless DC Motor

Considering the steering characters of one type of wheeled armored vehicle, a brushless direct current （DC） motor is adapted as the actuator for steering control. After investigating the known algorithms, one kind of algorithm, which combines the fuzzy logic control with the self-adapting PID control and the startup and pre-hrake control, is put forward. Then a test-bed is constructed, and an experiment is conducted. The result of experiment confirms the validity of this algorithm in steering control of wheeled armored vehicle with brushless DC motor.

Neural adaptive sliding mode speed tracking control of a DC motor

We propose a BPNN based adaptive sliding mode control scheme for speed tracking of a DC motor with unknown system nonlinearities. The input-output linearization technique is used to cancel the nonlinearities, and output of the BPNN is incorporated into the controller in the proposed scheme. It is shown that the rotor speed of a DC motor can follow any arbitrarily selected trajectories under variable load torque. Then the application of the approach is tested via some simulations.

双馈抽水蓄能机组中双向DC/DC变换器研究

为解决双馈抽水蓄能电机低电压穿越的问题,加入双向DC/DC与超级电容保护支路,其中双向DC/DC变换器采用两相交错式双向半桥拓扑结构。本文采用软开关技术有效解决变换器中开关损耗高的问题,对变换器在Buck和Boost模式下分别进行软开关技术分析。在MATLAB中搭建DC/DC效率模块、瞬态响应调整模块、工作范围模块和硬件电路模型,采用双电流内环和电压外环的控制方式。仿真结果表明在软开关的作用下,开关管实现了零电压导通和零电压关断,有效降低了开关损耗,提高大功率电力电子设备利用效率,具有一定的实用性和研究价值。

A New Method for Reducing Commutation Torque Ripples in BLDC Motors

A new compensation method and an algorithm for compensating for the commutation torque ripples of the trapezoidal EMF brushless DC motor are put forward. Simulation and experimental results show that this method is correct and practical.

Fault Tolerant Neuro-Robust Position Control of DC Motors

DC motors are widely used in industry such as mechanics, robotics, and aerospace engineering. In this paper, we present a high performance control method for position control of DC motors. Fault-tolerant control model are also addressed to combine with neuro-robust control approach. It is shown that with the proposed control algorithms, external disturbances and coupled dynamics inherent in the system are effectively compensated using neural network unit in which no analytical estimation on the upper bound of the reconstruction error and uncertainties is needed. Simulations on various flight conditions also confirm the effectiveness of the proposed methods.