The Line Shape of Double-Sided Tooth-Disk Waveguide Filters Based on Plasmon-Induced Transparency

We numerically investigate a coupled-resonator structure consisting of a stub resonator and a nanodisk resonator using a two-dimensional finite element method. Simulation results show that plasmon-induced transparency （PIT） occurs in the transmission spectra, and the sharp asymmetric Fano lines increase the sensitivity to 1.4 ×10^3 nm/RIU. We also analyze the properties of the structure with different radii of the nanodisk and the length of the tooth cavity. Moreover, we find that the PIP only happens when the staggered system is around a fixed location with different separate distances, which is not similar to the previous researches. Our model may be important to photonic-integrated circuits and the sensitivity in sensors.

Multiple Kalman filters model with shaping filter GPS real-time deformation analysis

In order to detect the deformation in real-time of the GPS time series and improve its reliability, the multiple Kalman filters model with shaping filter was proposed. Two problems were solved: firstly, because the GPS real-time deformation series with a high sampling rate contain coloured noise, the multiple Kalman filter model requires the white noise, and the multiple Kalman filters model is augmented by a shaping filter in order to reduce the colored noise; secondly, the multiple Kalman filters model with shaping filter can detect the deformation epoch in real-time and improve the quality of GPS measurements for the real-time deformation applications. Based on the comparisons of the applications in different GPS time series with different models, the advantages of the proposed model were illustrated. The proposed model can reduce the colored noise, detect the smaller changes, and improve the precision of the detected deformation epoch.

Digitalization of inverting filter shaping circuit for nuclear pulse signals

In the design of filter shaping circuits for nuclear pulse signals,inverting filter shaping circuits perform better than non-inverting filter shaping circuits.Because these circuits facilitate changing the phase of a pulse signal,they are widely used in processing nuclear pulse signals.In this study,the transfer functions of four types of inverting filter shaping circuits,namely the common inverting filter shaping,improved inverting filter shaping,multiple feedback low-pass filter shaping,and third-order multiple feedback low-pass filter shaping,in the Laplacian domain,are derived.We establish the numerical recursive function models and digitalize the four circuits,obtain the transfer functions in the Z domain,and analyze the filter performance and amplitude-frequency response characteristics in the frequency domain.Based on the actual nuclear pulse signal of the Si-PIN detector,we realize four types of inverting digital shaping.The results show that under the same shaping parameters,the common inverting digital shaping has better amplitude extraction characteristics,the third-order multiple feedback low-pass digital shaping has better noise suppression performance,and the multiple feedback digital shaping takes into account both pulse amplitude extraction and noise suppression performance.

A New Two-Branch Amplification Architecture and its Application with Various Modulated Signals

This paper proposes a new two-branch amplification architecture that combines baseband signal decomposition with RF front-end optimization. In the proposed architecture, the filtered modulated signals are separated into two components that are then amplified independently and combined to regenerate an amplified version of the original signal. A branch with an efficient amplifier transmits a low-varying envelope signal that contains the main part of the information. Another branch amplifies the residual portion of the signal. The baseband decomposition and parameters of the RF part are optimized to find the configuration that gives the best power efficiency and linearity. For M-ary quadrature amplitude modulation （M-QAM） signals, this technique is limited in terms of power efficiency. However, for filtered continuous phase modulation （CPM） signals, especially for minimum shift keying （MSK） and Gaussian MSK （GMSK） signals, high power efficiency can be achieved with no significant impact on the overall linearity. The results show that this technique gives better performance than the single-ended ctass-B amplifier.

Trapezoidal pulse shaping for pile-up pulse identification in X-ray spectrometry

Energy resolution is affected by the intrinsic energy resolution of the detector, ballistic deficit, pileup pulses and noise. Pile-up pulses become the dominant factor that degrades energy resolution after the system is established, so pile-up rejection is often applied to obtain good energy resolution by discarding pulses that are expected to be contaminated by pile-up. However, pile-up rejection can reduce count rates and thus lower the measurement precision. In order to improve count rates and maintain energy resolution, a new method of pile-up pulse identification based on trapezoidal pulse shaping is presented. Combined with pulse width discrimination, this method is implemented by recording pulses that are not seriously piled up. Some experimental tests with a Cu-Pb alloy sample are carried out to verify the performance of this method in X-ray spectrometry. The results show that the method can significantly improve count rates without degrading energy resolution.

H_(∞)control in the frequency domain for a semi-active floor isolation system

A floor isolation system installed in a single floor or room in a fixed base structure is designed to protect equipment.With this configuration,the input motions to the floor isolation from the ground motions are filtered by the structure,leaving the majority of the frequency content of the input motion lower than the predominant frequency of the structure.The floor isolation system should minimize the acceleration to protect equipment;however,displacement must also be limited to save floor space,especially with long period motion.Semi-active control with an H_(∞)control was adopted for the floor isolation system and a new input shaping filter was developed to account for the input motion characteristics and enhance the effectiveness of the H_(∞)control.A series of shake table tests for a semi-active floor isolation system using rolling pendulum isolators and a magnetic-rheological damper were performed to validate the H_(∞)control.Passive control using an oil damper was also tested for comparison.The test results show that the H_(∞)control effectively reduced acceleration for short period motions with frequencies close to the predominant frequency of the structure,as well as effectively reduced displacement for long period motions with frequencies close to the natural frequency of the floor isolation system.The H_(∞)control algorithm proved to be more advantageous than passive control because of its capacity to adjust control strategies according to the different motion frequency characteristics.

Using the shaping filter for removing the effcets of the bubble pulses of explosive charge

Using the shaping filter to remove the effects of the bubble pulses of explosive charge, we obtained the impulse response function of the sea bottom. The result is quite satisfactory.