Integrated high-performance and accurate shaping technology of low-cost powder metallurgy titanium alloys: A comprehensive review

The practical engineering applications of powder metallurgy (PM) Ti alloys produced through cold compaction and pressure-less sintering are impeded by poor sintering densification, embrittlement caused by excessive O impurities, and severe sintering deforma-tion resulting from the use of heterogeneous powder mixtures. This review presents a summary of our previous work on addressing the above challenges. Initially, we proposed a novel strategy using reaction-induced liquid phases to enhance sintering densification. Near- complete density (relative density exceeding 99%) was achieved by applying the above strategy and newly developed sintering aids. By focusing on the O-induced embrittlement issue, we determined the onset dissolution temperature of oxide films in the Ti matrix. On the basis of this finding, we established a design criterion for effective O scavengers that require reaction with oxide films before their dissol-ution. Consequently, a ductile PM Ti alloy was successfully obtained by introducing 0.3wt% NdB6 as the O scavenger. Lastly, a powder- coating strategy was adopted to address the sintering deformation issue. The ultrafine size and shell-like distribution characteristics of coating particles ensured rapid dissolution and homogeneity in the Ti matrix, thereby facilitating linear shrinkage during sintering. As a result, geometrically complex Ti alloy parts with high dimensional accuracy were fabricated by using the coated powder. Our fundament-al findings and related technical achievements enabled the development of an integrated production technology for the high-performance and accurate shaping of low-cost PM Ti alloys. Additionally, the primary engineering applications and progress in the industrialization practice of our developed technology are introduced in this review.

Assessment of Dependent Performance Shaping Factors in SPAR-H Based on Pearson Correlation Coefficient

With the improvement of equipment reliability,human factors have become the most uncertain part in the system.The standardized Plant Analysis of Risk-Human Reliability Analysis(SPAR-H)method is a reliable method in the field of human reliability analysis(HRA)to evaluate human reliability and assess risk in large complex systems.However,the classical SPAR-H method does not consider the dependencies among performance shaping factors(PSFs),whichmay cause overestimation or underestimation of the risk of the actual situation.To address this issue,this paper proposes a new method to deal with the dependencies among PSFs in SPAR-H based on the Pearson correlation coefficient.First,the dependence between every two PSFs is measured by the Pearson correlation coefficient.Second,the weights of the PSFs are obtained by considering the total dependence degree.Finally,PSFs’multipliers are modified based on the weights of corresponding PSFs,and then used in the calculating of human error probability(HEP).A case study is used to illustrate the procedure and effectiveness of the proposed method.

Nonbinary ldpc-coded probabilistic shaping scheme for MIMO systems based on signal space diversity

This paper first describes a binary Low-Density Parity-Check(LDPC)-coded Probabilistic Shaping(PS)scheme for Multiple-Input Multiple-Output(MIMO)systems based on Signal Space Diversity(SSD).Second,a Nonbinary(NB)LDPC-coded PS scheme for MIMO systems based on SSD is proposed.The first scheme can be used to obtain a shaping gain,whereas the second can also realize a coding gain.The theoretical average mutual information of the optimized rotated quadrature amplitude modulation constellations is analyzed and the simulated error per-formance with 22 and 44 MIMO schemes is investigated.The theoretical average mutual information analysis and simulation results show that the proposed NB LDPC-coded PS scheme for MIMO systems based on SSD is reliable and robust,and is therefore suitable for future wireless communication systems.

Joint Optimization of Precoding and Constellation Shaping for Faster-than-Nyquist Signaling

Faster-than-Nyquist(FTN)signaling is a potential scheme for the sixth generation(6G)communication system to improve the spectral efficiency(SE).In this paper,we propose a joint optimization algorithm of precoding and constellation shaping for FTN signaling,which is based on simulated optimization via the bare bones particle swarm optimization(BBPSO).The information-theoretical analysis and simulated error performance show that the proposed method is efficient,which can get a significant improvement in terms of average mutual information(AMI)and bit error rate(BER)performance.The simulated BER results verify the theoretical AMI analysis.Compared with the conventional regular 16QAM FTN scheme,when BER is at 10-5,the joint optimized scheme can obtain 0.50 dB and 0.60 dB performance gain with SE at 3.077 bits/s/Hz and 3.282 bits/s/Hz,respectively.Therefore,the proposed scheme is reliable,and thus suitable for the 6G communication.

Asia-Pacific Regional Economic Cooperation Under the Reshaping of Global Production and Supply Chains

As part of the important trends of the current development of the world economy,the reshaping of global industry and supply chains interacts with the intensified changes unprecedented in the past century in an increasingly close manner.“Benefit-sharing and risk-sharing”,the characteristics of global industry and supply chains,have a profound influence on the distribution of benefits among countries and the effectiveness of global economic governance.

Binary Phase Shaping and SHG Contrast Ratios

Finding binary sequences with Large SHG ratios is very important in the field of ultrafast science, biomedical optics, high-resolution microscopy and label-free imaging. In this paper, we have demonstrated the relation between the SHG contrast ratio and the traditional Merit Factor values. And in the light from known results in Merit Factor Problems, we have shown that Legendre Sequences or Jacobi Sequences, are still the best candidates to obtain binary sequences with large SHG contrast ratios. The authors also discussed the SHG behaviors on some sequences obtained from cyclotomic classes over the finite field GF (2l) .

A study on the treatment of chloasma with moxibustion based on the theory of“Yang transforming Qi,and Yin shaping”

Background:“Yang Transforming Qi and Yin shaping”comes from“Plain Question Yin and Yang should be like the theory”.Chinese medicine believes that the imbalance of yin and yang is the cause of human diseases.One of the strengths of TCM in treating diseases is holistic regulation.The theory of“Yang transforming Qi,and Yin shaping”implies a strong holistic view.Chloasma,one of the common skin diseases,seriously affects the physical and mental health of patients due to its unclear etiology,difficult treatment and easy recurrence.The occurrence and development of chloasma are closely related to internal organs.This paper is based on the theory of internal meridian,“Yang transforming Qi,and Yin shaping”which attaches importance to the concept of“Yang Qi”,from a new understanding of the pathogenesis etiology of chloasma.Methods:The author believes that the incidence of the disease is the deficiency of Yang Qi,which can’t promote the movement of Qi and blood to nourish the face,resulting in tangible material condensation,so proposes that this disease needs to be promoted by Yang transforming Qi and warm to dissipate.Moxibustion belongs to the fire,and its warming effect can dissipate the tangible evil.Results:Combined with clinical practice and the theory of internal meridian,the author elaborated that moxibustion is one of the effective methods for treating chloasma,which provides a new way of thinking for the treatment of chloasma.Conclusion:“Yang Transforming Qi and Yin shaping”can be used to guide the treatment of chloasma.

Driving Behavior Shaping Model in Road Traffic System

In order to give a new way for modeling driving behavior, identifying road traffic accident causation and solving a variety of road traffic safety problems such as driving errors prevention and driving behavior analysis, a new driving behavior shaping model is proposed, which could be used to assess the degree of effect of driving error upon road traffic safety. Driver behavior shaping model based on driving reliability and safety analysis could be used to identify the road traffic accident causation, to supply data for driver's behavior training, to evaluate driving procedures, to human factor design of road traffic system.

A Satellite Communication System Transmission Scheme Based on Probabilistic Shaping

In this paper, A transmission scheme based on probabilistic shaping applied to satellite communication systems is proposed. 16QAM is taken as an example to establish a 1GBaud ROF experimental system working in Ka-band. The experiment results show that the PS-16QAM signal has better performance in terms of bit error rate than the uniform 16QAM, and its performance is close to the uniform 8QAM scheme.

One-time Shaping Technological System of Lightweight Roof Greening

Lightweight roof greening is an important way for improving urban ecological environment and has good ecological and social benefits, but the investment is- too-high for the investors. Therefore, it is necessary to improve the system of lightweight roof greening. This study introduced a lightweight roof greening mode with low cost, simple construction, rapid formation, good economic benefit and convenient curing.

Grain Shape Genes:Shaping the Future of Rice Breeding

The main goals of rice breeding nowadays include increasing yield,improving grain quality,and promoting complete mechanized production to save labor costs.Rice grain shape,specified by three dimensions,including grain length,width and thickness,has a more precise meaning than grain size,contributing to grain appearance quality as well as grain weight and thus yield.Furthermore,the divergence of grain shape characters could be utilized in mechanical seed sorting in hybrid rice breeding systems,which has been succeeded in utilizing heterosis to achieve substantial increase in rice yield in the past decades.Several signaling pathways that regulate rice grain shape have been elucidated,including G protein signaling,ubiquitination-related pathway,mitogen-activated protein kinase signaling,phytohormone biosynthesis and signaling,micro RNA process,and some other transcriptional regulatory pathways and regulators.This review summarized the recent progress on molecular mechanisms underlying rice grain shape determination and the potential of major genes in future breeding applications.

Coin-structured tunable beam shaping assembly design for accelerator-based boron neutron capture therapy for tumors at different depths and sizes

In the past decade,boron neutron capture therapy utilizing an accelerator-based neutron source(ABNS)designed primarily for producing epithermal neutrons has been implemented in the treatment of brain tumors and other cancers.The specifications for designing an epithermal beam are primarily based on the IAEA-TECODC-1223 report,issued in 2001 for reactor neutron sources.Based on this report,the latest perspectives and clinical requirements,we designed an ABNS capable of adjusting the average neutron beam energy.The design was based on a 2.8 MeV,20 mA proton beam bombarding a lithium target to produce neutrons that were subsequently moderated and tuned through a tunable beam shaping assembly(BSA)which can modify the thicknesses and materials of the coin-shaped moderators,back reflectors,filters,and collimators.The simulation results demonstrated that epithermal neutron beams for deep seated tumor treatment,which were generated by utilizing magnesium fluoride with lengths ranging between 28 and 36 cm as the moderator,possessed a treatment depth of 5.6 cm although the neutron flux peak shifts from 4.5 to 1.0 keV.When utilizing a thinner moderator,a less accelerated beam power can meet the treatment requirements.However,higher powers reduced the treatment time.In contrast,employing a thick moderator can reduce the skin dose.In scenarios that required relatively low energy neutron beams,the removal of the thermal neutron filter can raise the thermal neutron flux at the beam port.And the depth of the dose rate peak could be adjusted between 0.25 and 2.20 cm by combining magnesium fluoride and polyethylene coins of different thicknesses.Hence,this device has a better adaptability for the treatment of superficial tumors.Overall,the tunable BSA provides greater flexibility for clinical treatment than common BSA designs that can only adjust the port size.

基于Shaping-DDPG模型的变压器负荷预测技术研究

为了协调电力系统供需平衡,降低运维风险和成本,引入Shaping技术改进了深度确定性策略梯度(DDPG)算法,得到Shaping-DDPG预测模型。加入经验回放技术和目标网络技术以消除数据间的关联性;设计变压器网络评估函数来评价变压器网络的优劣状态;通过数据处理模块和卷积模块提取原始数据特征,提高变压器系统的感知能力和学习效率。研究表明:与其他算法预测效果相比,Shaping-DDPG模型的RMSE误差平均值(93 MW)最低,比DDPG模型、RNN模型和SVM模型分别降低了42 MW、93 MW和145 MW。相较于非线性变压器负荷系统,Shaping-DDPG模型具有强大的反馈记忆功能,能准确获取负荷序列潜在的变化趋势,在变压器负荷曲线呈现波动时依然能够保证良好的预测能力。该研究为降低电网公司资源浪费和运维成本、协调电网公司与变压器系统之间的供需平衡提供了思路,提高了运作效益。

Terahertz shaping technology based on coherent beam combining

The generation of terahertz(THz) waves by focusing a femtosecond pulsed laser beam at a distance is able to overcome the strong absorption properties of air and has rapidly attracted the attention of industry. However, the poor directionality of the THz wave radiation generated by this method is not conducive to THz wave applications. By controlling the morphology of the ultrafast laser-excited plasma filament and its electron density distribution through coherent beam combining technology, we achieve direct THz beam shaping and are able to obtain THz wave radiation of Gaussian or arbitrary transverse distribution. The novel experimental approach proposed in this paper opens up the research field of direct THz wave shaping using plasma. Moreover, it innovates multi-parameter convergence algorithms and, by doing so, has the potential to find beam patterns with higher energy conversion efficiency and break the energy limit of THz waves emitted by lasers at high power.

Pulse-shaping method for real-time neutron/gamma discrimination at low sampling rates

The Na I:Tl scintillator is an innovative material for dual-gamma-ray and neutron detection with a low ^(6)Li concentration.To achieve real-time n/γ discrimination,a zero-crossing time comparison algorithm based on trapezoidal pulse shaping was developed.The algorithm can operate efficiently at low sampling rates and was implemented on a single-probe portable digital n/γ discriminator based on a field-programmable gate array.The discriminator and Na I:Tl,^(6)Li detector were tested in a neutron-gamma mixed field produced by an ^(241)Am-Be neutron source to evaluate the performance of the algorithm.The figure of merits was measured as 2.88 at a sampling rate of 50 MHz,indicating that the discriminator with its embedded algorithm has a promising n/γ discrimination capability.Efficient discrimination at sampling rates of 40 and 25 MHz demonstrates that the capability of this method is not limited by low sampling rates.

Magnetic Field-Based Reward Shaping for Goal-Conditioned Reinforcement Learning

Goal-conditioned reinforcement learning(RL)is an interesting extension of the traditional RL framework,where the dynamic environment and reward sparsity can cause conventional learning algorithms to fail.Reward shaping is a practical approach to improving sample efficiency by embedding human domain knowledge into the learning process.Existing reward shaping methods for goal-conditioned RL are typically built on distance metrics with a linear and isotropic distribution,which may fail to provide sufficient information about the ever-changing environment with high complexity.This paper proposes a novel magnetic field-based reward shaping(MFRS)method for goal-conditioned RL tasks with dynamic target and obstacles.Inspired by the physical properties of magnets,we consider the target and obstacles as permanent magnets and establish the reward function according to the intensity values of the magnetic field generated by these magnets.The nonlinear and anisotropic distribution of the magnetic field intensity can provide more accessible and conducive information about the optimization landscape,thus introducing a more sophisticated magnetic reward compared to the distance-based setting.Further,we transform our magnetic reward to the form of potential-based reward shaping by learning a secondary potential function concurrently to ensure the optimal policy invariance of our method.Experiments results in both simulated and real-world robotic manipulation tasks demonstrate that MFRS outperforms relevant existing methods and effectively improves the sample efficiency of RL algorithms in goal-conditioned tasks with various dynamics of the target and obstacles.

Fractal nature of human gastrointestinal system:Exploring a new era

The morphological complexity of cells and tissues,whether normal or pathological,is characterized by two primary attributes:Irregularity and self-similarity across different scales.When an object exhibits self-similarity,its shape remains unchanged as the scales of measurement vary because any part of it resembles the whole.On the other hand,the size and geometric characteristics of an irregular object vary as the resolution increases,revealing more intricate details.Despite numerous attempts,a reliable and accurate method for quantifying the morphological features of gastrointestinal organs,tissues,cells,their dynamic changes,and pathological disorders has not yet been established.However,fractal geometry,which studies shapes and patterns that exhibit self-similarity,holds promise in providing a quantitative measure of the irregularly shaped morphologies and their underlying self-similar temporal behaviors.In this context,we explore the fractal nature of the gastrointestinal system and the potential of fractal geometry as a robust descriptor of its complex forms and functions.Additionally,we examine the practical applications of fractal geometry in clinical gastroenterology and hepatology practice.

A Shape-Memory Deployable Subsystem with a Large Folding Ratio in China’s Tianwen-1 Mars Exploration Mission

Once China’s Tianwen-1 Mars probe arrived in a Mars orbit after a seven-month flight in the deep cold space environment,it would be urgently necessary to monitor its state and the surrounding environment.To address this issue,we developed a flexible deployable subsystem based on shape memory polymer composites(SMPC-FDS)with a large folding ratio,which incorporates a camera and two temperature telemetry points for monitoring the local state of the Mars orbiter and the deep space environment.Here,we report on the development,testing,and successful application of the SMPC-FDS.Before reaching its Mars remote-sensing orbit,the SMPC-FDS is designed to be in a folded state with high stiffness;after reaching orbit,it is in a deployed state with a large envelope.The transition from the folded state to the deployed state is achieved by electrically heating the shape memory polymer composites(SMPCs);during this process,the camera on the SMPC-FDS can capture the local state of the orbiter from multiple angles.Moreover,temperature telemetry points on the SMPC-FDS provide feedback on the environment temperature and the temperature change of the SMPCs during the energization process.By simulating a Mars on-orbit space environment,the engineering reliability of the SMPC-FDS was comprehensively verified in terms of the material properties,structural dynamic performance,and thermal vacuum deployment feasibility.Since the launch of Tianwen-1 on 23 July 2020,scientific data on the temperature environment around Tianwen-1 has been successfully acquired from the telemetry points on the SMPCFDS,and the local state of the orbiter has been photographed in orbit,showing the national flag of China fixed on the orbiter.

An Analysis of the Static and Dynamic Behavior of the Hydraulic Compensation System of a Multichannel Valve

Electro-hydraulic proportional valve is the core control valve in many hydraulic systems used in agricultural and engineering machinery.To address the problem related to the large throttling losses and poor stability typically associated with these valves,here,the beneficial effects of a triangular groove structure on the related hydraulic response are studied.A mathematical model of the pressure compensation system based on the power-bond graph method is introduced,and the AMESim software is used to simulate its response.The results show that the triangular groove structure increases the jet angle and effectively compensates for the hydrodynamic force.The steady-state differential pressure at the valve port of the new pressure compensation structure was 0.65 MPa.Furthermore,experimental results show that the pressure difference at the main valve port is 0.73 MPa,and that the response time is less than 0.2 s.It is concluded that the new compensation structure has good pressure compensation response characteristics.

Liver Tumor Decision Support System on Human Magnetic Resonance Images:A Comparative Study

Liver cancer is the second leading cause of cancer death worldwide.Early tumor detection may help identify suitable treatment and increase the survival rate.Medical imaging is a non-invasive tool that can help uncover abnormalities in human organs.Magnetic Resonance Imaging(MRI),in particular,uses magnetic fields and radio waves to differentiate internal human organs tissue.However,the interpretation of medical images requires the subjective expertise of a radiologist and oncologist.Thus,building an automated diagnosis computer-based system can help specialists reduce incorrect diagnoses.This paper proposes a hybrid automated system to compare the performance of 3D features and 2D features in classifying magnetic resonance liver tumor images.This paper proposed two models;the first one employed the 3D features while the second exploited the 2D features.The first system uses 3D texture attributes,3D shape features,and 3D graphical deep descriptors beside an ensemble classifier to differentiate between four 3D tumor categories.On top of that,the proposed method is applied to 2D slices for comparison purposes.The proposed approach attained 100%accuracy in discriminating between all types of tumors,100%Area Under the Curve(AUC),100%sensitivity,and 100%specificity and precision as well in 3D liver tumors.On the other hand,the performance is lower in 2D classification.The maximum accuracy reached 96.4%for two classes and 92.1%for four classes.The top-class performance of the proposed system can be attributed to the exploitation of various types of feature selection methods besides utilizing the ReliefF features selection technique to choose the most relevant features associated with different classes.The novelty of this work appeared in building a highly accurate system under specific circumstances without any processing for the images and human input,besides comparing the performance between 2D and 3D classification.In the future,the presented work can be extended to be used in the huge dataset.Then,it can be a reliable,efficient Computer Aided Diagnosis(CAD)system employed in hospitals in rural areas.