A Simple Shear Model for the Asymmetry in the Paleoproterozoic Fold Belt in Liaodong Peninsula

Several aspects of the Liaodong Paleoproterozioc fold belt, including its components, tectonic, metamorphic and magmatic characteristics are discussed in the paper, with emphasis on the asymmetry of the fold belt and differences between the northern lineal-fold belt and the southern dome-fold belt. It is suggested that the fold belt is one magmatic passive margin, instead of a rift zone or the classical passive continental margin. The formation and evolution of the fold belt is dis- cussed with a simple shear model, which may best explain the co-existence of contemporaneous tectonic facies with different characteristics, the volcanic and plutonic activities, sedimentary formations and their geological attributes etc.

Mechanical behaviors of backfill-rock composites: Physical shear test and back-analysis

The shear behavior of backfill-rock composites is crucial for mine safety and the management of surface subsidence.For exposing the shear failure mechanism of backfill-rock composites,we conducted shear tests on backfill-rock composites under three constant normal loads,compared with the unfilled rock.To investigate the macro-and meso-failure characteristics of the samples in the shear tests,the cracking behavior of samples was recorded by a high-speed camera and acoustic emission monitoring.In parallel with the experimental test,the numerical models of backfill-rock composites and unfilled rock were established using the discrete element method to analyze the continuous-discontinuous shearing process.Based on the damage mechanics and statistics,a novel shear constitutive model was proposed to describe mechanical behavior.The results show that backfill-rock composites had a special bimodal phenomenon of shearing load-deformation curve,i.e.the first shearing peak corresponded to rock break and the second shearing peak induced by the broken of aeolian sand-cement/fly ash paste backfill.Moreover,the shearing characteristic curves of the backfill-rock composites could be roughly divided into four stages,i.e.the shear failure of the specimens experienced:stage I:stress concentration;stage II:crack propagation;stage III:crack coalescence;stage IV:shearing friction.The numerical simulation shows that the existence of aeolian sand-cement/fly ash paste backfill inevitably altered the coalescence type and failure mode of the specimens and had a strengthening effect on the shear strength of backfillrock composites.Based on damage mechanics and statistics,a shear constitutive model was proposed to describe the shear fracture characteristics of specimens,especially the bimodal phenomenon.Finally,the micro-and meso-mechanisms of shear failure were discussed by combining the micro-test and numerical results.The research can advance the better understanding of the shear behavior of backfill-rock composites and contribute to the safety of mining engineering.

Modeling the Undrained Shear Strength with Soil Index Properties for Niger Delta Soft Clays

The aim of this study was to model the Undrained Shear Strength (USS) of soil found in the coastal region of the Niger Delta in Nigeria with some soil properties. The undrained shear strength (USS) is a key parameter needed for most geotechnical/structural designs. Accurate determination of the USS of soft clays can be challenging to obtain in the laboratory due to the difficulty in remoulding the clay to its in-situ conditions before testing and more accurate test such as Cone Penetration test (CPT) can be quite expensive. This study was carried out at Escravos site which is located in Delta state, Nigeria. Three Boreholes were drilled and soil samples were collected at 0.75 m intervals up to a depth of 45 m. Laboratory tests were used to obtain the moisture content, bulk unit weight, liquid and plastic limit, while CPT was used in obtaining the undrained shear strength. Classification of the soil samples was done by adopting the Unified Soil Classification System and various models relating the USS with the soil properties were developed. The result showed that most of the soils at Escravos site were predominately inorganic clay of high plasticity which are problematic due to the expansion and shrinking nature of this type of soil. The model developed showed that the soil properties that gave the best fit with the USS were the moisture content and effective stress of the soil. The coefficient of determination (R2) and the root mean square error (RMSE) obtained for this model were 0.805 and 6.37 KN/m2, respectively.

A new numerical model of ring shear tester for shear band soil considering friction-induced thermal pressurization

In this study,a new numerical model of ring shear tester for shear band soil of landslide was established.The special feature of this model is that it considers the mechanism of friction-induced thermal pressurization,which is potentially an important cause of high-speed catastrophic landslides.The key to the construction of this numerical ring shear model is to realize the THM(thermo-hydro-mechanical)dynamic coupling of soil particles,which includes the processes of frictional heating,thermal pressurization,and strength softening during shearing of solid particles.All of these are completed by using discrete element method.Based on this new model,the characteristics of shear stress change with shear displacement,as well as the variation of temperature and pore pressure in the specimen,are studied at shear rates of 0.055 m/s,0.06 m/s,0.109 m/s and 1.09 m/s,respectively.The results show that the peak strength and residual strength of specimen are significantly reduced when the mechanism of frictioninduced thermal pressurization is considered.The greater the shear rate is,the higher the temperature as well as the pore pressure is.The effect of shear rate on the shear strength is bidirectional.The simulation results demonstrate that this model can effectively simulate the mechanism of friction-induced thermal pressurization of shear band soil during ring shear process,and the shear strength softening in the process.The new numerical ring shear model established in this study is of great significance for studying the dynamic mechanism of high-speed catastrophic landslides.

An interface shear damage model of chromium coating/steel substrate under thermal erosion load

The Cr-plated coating inside a gun barrel can effectively improve the barrel’s erosion resistance and thus increase the service life.However,due to the cyclic thermal load caused by high-temperature gunpowder,micro-element damage tends to occur within the Cr coating/steel substrate interface,leading to a gradual deterioration in macro-mechanical properties for the material in the related region.In order to mimic this cyclic thermal load and,thereby,study the thermal erosion behavior of the Cr coating on the barrel’s inner wall,a laser emitter is utilized in the current study.With the help of in-situ tensile test and finite element simulation results,a shear stress distribution law of the Cr coating/steel substrate and a change law of the interface ultimate shear strength are identified.Studies have shown that the Cr coating/steel substrate interface’s ultimate shear strength has a significant weakening effect due to increasing temperature.In this study,the interfacial ultimate shear strength decreases from 2.57 GPa(no erosion)to 1.02 GPa(laser power is 160 W).The data from this experiment is employed to establish a Cr coating/steel substrate interface shear damage model.And this model is used to predict the flaking process of Cr coating by finite element method.The simulation results show that the increase of coating crack spacing and coating thickness will increase the service life of gun barrel.

SHEAR BEAM MODEL FOR INTERFACE FAILURE UNDER ANTIPLANE SHEAR(Ⅱ)—INSTABILITY

Based on the (Ⅰ) of the present work, the behavior of shear beam model at crack initiation stage and at instable propagation stage was studied. The prime results include: 1) discriminant equation which clarifies the mode of instability, snap_back or snap_through, was established; 2) analytical solution was given out for the double shear beam and the load_displacement diagram for monotonic loading was presented for a full process; and 3) the problem of the energy release induced by instability was discussed.

An Application of the Modified Shear Lag Model to Study the Influence of Thermal Residual Stresses on the Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

The modified shear lag model proposed recently was applied to calculate thermal residual stresses and subsequent stress distributions under tensile and compressive loadings. The expressions for the elastic moduli and the yield strengths under tensile and compressive loadings were derived which take account of thermal residual stresses. The asymmetries in the elastic modulus and the yield strength were interpreted using the derived expressions and the obtained results of the stress calculations. The model predictions have exhibited good agreements with the experimental results and also with the other theoretical predictions

Shear creep characteristics and constitutive model of limestone

The characters of limestone in weak interlayer of a high rocky slope in Xuzhou, China, are studied by shear static test and shear creep test. The results show that limestone specimens have attenuation creep properties and constant rate creep properties, almost have no accelerated creep properties. The exponential type empirical formula is selected to fit creep grading curves by polynomial regression analysis method, and the square sums of the fitting results residual are in the order of 10^(-7). Then grade creep curves at every shear loads are set up. Combining creep rate-time curve, the creep properties of limestone are analyzed. As the physical meaning of component model is clearer, the Poytin–Thomson model is set up. Through the least square method, the optimal parameters of Poytin–Thomson model are obtained,and the sums of squared residuals belong to 10^(-3)order of magnitude, which can meet the accuracy requirements of engineering calculation. So the Poytin–Thomson model can reflect the shear creep characteristics of limestone very well.

Effects of constitutive parameters on adiabatic shear localization for ductile metal based on JOHNSON-COOK and gradient plasticity models

By using the widely used JOHNSON-COOK model and the gradient-dependent plasticity to consider microstructural effect beyond the occurrence of shear strain localization,the distributions of local plastic shear strain and deformation in adiabatic shear band(ASB)were analyzed.The peak local plastic shear strain is proportional to the average plastic shear strain,while it is inversely proportional to the critical plastic shear strain corresponding to the peak flow shear stress.The relative plastic shear deformation between the top and base of ASB depends on the thickness of ASB and the average plastic shear strain.A parametric study was carried out to study the influence of constitutive parameters on shear strain localization.Higher values of static shear strength and work to heat conversion factor lead to lower critical plastic shear strain so that the shear localization is more apparent at the same average plastic shear strain.Higher values of strain-hardening exponent,strain rate sensitive coefficient,melting point,thermal capacity and mass density result in higher critical plastic shear strain,leading to less apparent shear localization at the same average plastic shear strain.The strain rate sensitive coefficient has a minor influence on the critical plastic shear strain,the distributions of local plastic shear strain and deformation in ASB.The effect of strain-hardening modulus on the critical plastic shear strain is not monotonous.When the maximum critical plastic shear strain is reached,the least apparent shear localization occurs.

A Modified Monte Carlo Model of Speckle Tracking of Shear Wave Induced by Acoustic Radiation Force for Acousto-Optic Elasticity Imaging

A modified Monte Carlo model of speckle tracking of shear wave propagation in scattering media is proposed. The established Monte Carlo model mainly concerns the variations of optical electric field and speckle. The two- dimensional intensity distribution and the time evolution of speckles in different probe locations are obtained. The fluctuation of speckle intensity tracks the acoustic-radiation-force shear wave propagation, and especially the reduction of speckle intensity implies attenuation of shear wave. Then, the shear wave velocity is estimated quantitatively on the basis of the time-to-peak algorithm and linear regression processing. The results reveal that a smaller sampling interval yields higher estimation precision and the shear wave velocity is estimated more efficiently by using speckle intensity difference than by using speckle contrast difference according to the estimation error. Hence, the shear wave velocity is estimated to be 2.25 m/s with relatively high accuracy for the estimation error reaches the minimum （0.071）.

A new shear rheological model for a soft interlayer with varying water content

The rheological behavior of a soft interlayer is critical to understanding slope stability, which is closely related to the water content of the soft interlayer. This study used the soft interlayer of the Permian Maokou Formation in Southwest China as an example to perform ring shear creep tests with different water content amounts. The effect of water content on the creep properties of the soft interlayer was analyzed, and a new shear rheological model was established. This research produced several findings. First, the ring shear creep deformation of the soft interlayer samples varied with the water content and the maximum instantaneous shear strain increment occurred near the saturated water content. As the water content increased, the cumulative creep increment of the samples increased. Second, the water content significantly affected the long-term strength of the soft interlayer, which decreased with the increase of water content, exhibiting a negative linear correlation. Third, a constitutive equation for the new rheological model was derived, and through fitting of the ring shear creep test data, the validity and applicability of the constitutive equation were proven. This study has developed an important foundation for studying the long-term deformation characteristics of a soft interlayer with varying water content.

SHEAR BEAM MODEL FOR INTERFACE FAILURE UNDER ANTIPLANE SHEAR(Ⅰ)—FUNDAMENTAL BEHAVIOR

The propagation of interlayer cracks and the resulting failure of the interface is a typical mode occurring in rock engineering and masonry structure. On the basis of the theory of elasto^plasticity and fracture mechanics, the shear beam model for the solution of interface failure was presented. The concept of `cohesive crack' was adopted to describe the constitutive behavior of the cohesive interfacial layer. Related fundamental equations such as equilibrium equation, constitutive equations were presented. The behavior of a double shear beam bonded through cohesive layer was analytically calculated. The stable propagation of interface crack and process zone was investigated.

Effects of Magnetic Shear on the Resistive Wall Mode Instability in a Cylindrical Model

The linear evolution of a resistive wall mode(RWM)with magnetic shears was analytically studied in a cylindrical geometry.The incompressible magnetohydrodynamic(MHD)equations were solved by the Fourier analysis method,and various equilibrium magnetic fields were considered.The shear in the magnetic field had an unstable effect on the linear evolution of the RWM.The linear growth rate increased obviously with increase of the magnetic shear rate for higher magnetic shears.Slow plasma rotation could stabilize the RWM with low magnetic shears,but the plasma rotation could not stabilize the RWM with high magnetic shears.The stabilizing effects of the wall conductivity on the RWM are more efficient for lager magnetic shear.

Mathematical Model and Experiment Validation of Fluid Torque by Shear Stress under Influence of Fluid Temperature in Hydro-viscous Clutch

The current design of hydro-viscous clutch（HVC） in tracked vehicle fan transmission mainly focuses on high-speed and high power. However, the fluid torque under the influence of fluid temperature can not be predicted accurately by conventional mathematical model or experimental research. In order to validate the fluid torque of HVC by taking the viscosity-temperature characteristic of fluid into account, the test rig is designed. The outlet oil temperature is measured and fitted with different rotation speed, oil film thickness, oil flow rate, and inlet oil temperature. Meanwhile, the film torque can be obtained. Based on Navier-Stokes equations and the continuity equation, the mathematical model of fluid torque is proposed in cylindrical coordinate. Iterative method is employed to solve the equations. The radial and tangential speed distribution, radial pressure distribution and theoretical flow rate are determined and analyzed. The models of equivalent radius and fluid torque of friction pairs are introduced. The experimental and theoretical results indicate that tangential speed distribution is mainly determined by the relative rotating speed between the friction plate and the separator disc. However, the radial speed distribution and pressure distribution are dominated by pressure difference at the lower rotating speed. The oil film fills the clearance and the film torque increases with increasing rotating speed. However, when the speed reaches a certain value, the centrifugal force will play an important role on the fluid distribution. The pressure is negative at the outer radius when inlet flow rate is less than theoretical flow, so the film starts to shrink which decreases the film torque sharply. The theoretical fluid torque has good agreement with the experimental data. This research proposes a new fluid torque mathematical model which may predict the film torque under the influence of temperature more accurately.

Research on Mechanical Model and Properties of New-type Negative Offset Structure in Spatial Seven-bar Heavy Shear

According to revised Cailikefu’s rolling shear force formula,motion path equation of spatial seven-bar path is built,and mechanical model,with such new structural features as negative offset,is thus successfully established for 2 800 mm heavy shear of some Iron&Steel Company. Shear force and bar force of steel plate,before and after adoption of negative offset structure,are analyzed,as well as horizontal force component of mechanism that influences pure rolling shear and back-wall push force that keeps blade clearance. The discovery is that back-wall push force could be kept large enough at rolling start-up (i.e. the time that the maximum rolling shear produces),meanwhile,back-wall push force is the most approximate to side forces with adoption of 60 mm-100 mm offset. Theoretical results and on-site shear quality both indicate that new structural features such as negative offset plays an important role in ensuring pure rolling shear and keeping blade clearance constant,which provide an effective means to improve quality of steel plate.

Mathematical Model and Theoretical Research of Flow Shear Constitutive Relation during Rheo-rolling of Semisolid Alloy

The mathematical model of flow shear constitutive relation during rheo-rolling process has been established. The distribution of velocity and shear stress in rolling cavity was investigated, and the effects of process parameters on shear stress of Sn-15 Pb alloy during rheo-rolling process were studied. In rolling cavity, the nearer the roll is, the bigger the velocity and shear stress are. The shear stress increases with the increment of the roll speed and the roll radius during rheo-rolling process, but deceases with the increment of the thickness of the strip. When the solid fraction of Sn-15 Pb alloy increases from 0.3 to 0.5, the shear stress increases slowly, but when the solid fraction increases from 0.5 to 0.6, the shear stress rapidly.

Dynamic modeling and control of extracellular ATP concentration on vascular endothelial cells via shear stress modulation

A new dynamic model for cell-deformation-induced adenosine triphosphate （ATP） release from vascular endothelial cells （VECs） is proposed in this paper to quantify the relationship between the ATP concentration at the surface of VECs and blood flow-induced shear stress. The simulation results demonstrate that ATP concentration at the surface of VECs predicted by the proposed new dynamic model is more consistent with the experimental observations than those by the existing static and dynamic models. Furthermore, it is the first time that a proportional-integral-derivative （PID） feedback controller is applied to modulate extracellular ATP concentration. Three types of desired ATP concentration profiles including constant, square wave and sinusoid are obtained by regulating the wall shear stress under this PID control. The systematic methodology utilized in this paper to model and control ATP release from VECs via adjusting external stimulus opens up a new scenario where quantitative investigations into the underlying mechanisms for many biochemical phenomena can be carded out for the sake of controlling specific cellular events.

Collinear micro-shear-bands model for grain-size and precipitate-size effects on the yield strength

Numerous experimental evidences show that the grain size may significantly alter the yield strength of metals.Similarly,innickel-based superalloys,the precipitate size also influences their yield strength.Then,how to describe such two kinds of size effects on the yield strength is a very practical challenge.In this study,according to experimental observations,a collinear micro-shear-bands model is proposed to explore these size effects on metal materials’yield strength.An analytical solution for the simple model is derived.It reveals that the yield strength is a function of average grain-size or precipitate-size,which is able to reasonably explain size effects on yield strength.The typical example validation shows that the new relationship is not only able to precisely describe the grain-size effect in some cases,but also able to theoretically address the unexplained Hall-Petch relationship between theprecipitate size and the yield strength of nickel-based superalloys.

A new semi-empirical spectrum model for complex steady shear viscosity of complex fluids

A semi-empirical spectrum model is proposed to describe the experimental data of the steady shear properties of a Shengli waxy crude oil near its gel point, where sophisticated structural effects become apparent due to the existence of waxy crystals in the crude oil. The model, consisting of a time spectrum, can well fit the steady shear viscosities of the waxy crude oil over the whole experimental shear rate region from 10-4 to 102 s- 1. Two other experiments on complex fluids reported recently in the literature are also well described by this model demonstrating the applicability and accuracy of the model.

Nonaffine Network Structural Model for Molten Low-Density Polyethylene and High-Density Polyethylene in Oscillatory Shear

We propose molten polymer's entanglement network deformation to be nonaffine and use transient network structural theory with the revised Liu's kinetics rate equation and the revised upper convected Maxwell constitutive equation to establish a nonaffine network structural constitutive model for studying the rheological behavior of molten Low Density Polyethylene (LDPE) and High Density Polyethylene (HDPE) in oscillatory shear. As a result, when the strain amplitude or frequency increases, the shear stress amplitude increases. At the same time, the accuracy of the nonaffine network model is higher than that of affine network model. It is clear that there is a small amount of nonaffine network deformation for LDPE melts which have long chain branches, and there is a larger amount of nonaffine network deformation in oscillatory shear for HDPE melts which has no long chain branches. So we had better consider the network deformation nonaffine when we establish the constitutive equations of polymer melts in oscillatory shear.