Effect of inorganic salt impurities on seeded precipitation of silica hydrate from sodium silicate solution

To clarify the precipitation of silica hydrate from the real desilication solutions of aluminosilicate solid wastes by adding seeds and improve integrated waste utilization,the seeded precipitation was studied using synthesized sodium silicate solution containing different inorganic salt impurities.The results show that sodium chloride,sodium sulfate,sodium carbonate,or calcium chloride can change the siloxy group structure.The number of high-polymeric siloxy groups decreases with increasing sodium chloride or sodium sulfate concentration,which is detrimental to seeded precipitation.Calcium chloride favors the polymerization of silicate ions,and even the chain groups precipitate with the precipitation of high-polymeric sheet and cage-like siloxy groups.The introduced sodium cations in sodium carbonate render a more open network structure of high-polymeric siloxy groups,although the carbonate ions favor the polymerization of siloxy groups.No matter how the four impurities affect the siloxy group structure,the precipitates are always amorphous opal-A silica hydrate.

Natural Silicate as a Solid Support for the Calix[4]Thiophosphorus Derivative for Removal Mercury (II), as Picrate from Water

Currently a technique widely used for gold extraction is mercury by amalgamation technique, the tailing produced pollutes water of all kinds, so it is necessary to develop a form of selective mitigation, for which it is necessary to use complexing agents based on calixarene functionalized with mercury sequestering agents. These are immobilized by adding supports based on natural silica to form polymers and make them insoluble in all types of solvents, so that they can be used as an extractor and at the same time regenerate to their original properties for continuous reuse.

Carbonation of Dicalcium Silicate Enhanced by Ammonia Bicarbonate and Its Mechanism

The strength development law of γ-type dicalcium silicate (γ-C_(2)S) under different carbonation processes was investigated,and the carbonation mechanism of γ-C_(2)S under the action of NH_(4)HCO_(3) was clarified by using a wide range of test methods,including XRD and SEM.A method of saturated NH_(4)HCO_(3) solution as a curing agent was identified to improve the carbonation efficiency and enhance the carbonation degree of γ-C_(2)S,and then a high-strength carbonated specimen was obtained.Microhardness analysis and SEM morphology analysis were conducted on the carbonised specimens obtained under atmospheric pressure carbonisation conditions using the curing agent.It was found that γ-C_(2)S could perform carbonisation well under atmospheric pressure,which promoted the carbonisation efficiency and decreased the carbonisation cost simultaneously.Therefore,a new carbonisation process solution was proposed for the rapid carbonisation of γ-C_(2)S.

Synergistic strengthening mechanism of Ca^(2+)-sodium silicate to selective separation of feldspar and quartz

Inhibitors are important for flotation separation of quartz and feldspar.In this study,a novel combined inhibitor was used to separate quartz and feldspar in near-neutral pulp.Selective inhibition of the combined inhibitor was assessed by micro-flotation experiments.And a series of detection methods were used to detect differences in the surface properties of feldspars and quartz after flotation reagents and put forward the synergistic strengthening mechanism.The outcomes were pointed out that pre-mixing combined inhibitors were more effective than the addition of Ca^(2+)and SS in sequence under the optimal proportion of 1:5.A concentrate from artificial mixed minerals that was characterized by a high quartz grade and a high recovery was acquired,and was found to be 90.70wt% and 83.70%,respectively.It was demonstrated that the combined inhibitor selectively prevented the action of the collector and feldspar from Fourier-transform infrared(FT-IR)and adsorption capacity tests.The results of X-ray photoelectron spectroscopy(XPS)indicated that Ca^(2+)directly interacts with the surface of quartz to increase the adsorption of collectors.In contrast,the chemistry property of Al on the feldspar surface was altered by combined inhibitor due to Na^(+)and Ca^(2+)taking the place of K^(+),resulting in the composite inhibitor forms a hydrophilic structure,which prevents the adsorption of the collector on the surface of feldspar by interacting with the Al active site.The combination of Ca^(2+)and SS synergically strengthens the difference of collecting property between quartz and feldspar by collector,thus achieving the effect of efficient separation.A new strategy for flotation to separate quartz from feldspar in near-neutral pulp was provided.

Effectiveness of Sodium Silicate on the Corrosion Protection of AA7075-T6 Aluminium Alloy in Sodium Chloride Solution

The influence of sodium silicate on the corrosion behaviour of aluminium alloy 7075-T6 in 0.1 M sodium chloride solution was studied by open circuit potential (OCP) and electrochemical impedance spectroscopy (EIS) techniques. Scanning electron microscopy (SEM) was used to characterize the AA7075-T6 surface. Silicate can significantly reduce corrosion deterioration and the inhibition efficiency increases with the concentration of Na2SiO3. The corrosion inhibition mechanism involves the formation of a protective film over the alloy surface by adsorption of aluminosilicate anions from solution, as has also been suggested by others in literature.

Adsorption of sodium polyacrylate at interface of dicalcium silicate-sodium aluminate solution

The adsorption isotherm of sodium polyacrylate on dicalcium silicate（2CaO-SiO2） in sodium aluminate solution at 80 ℃ was studied.The type of surface adsorption of sodium polyacrylate is saturated adsorption,and the adsorption behavior belongs to L-type,according with the monolayer adsorption model of Langmuir equation.The surface coverage of sodium polyacrylate is 1.06 mol/μm2.The relation curve between the surface pressure and the molecular area of adsorption film was obtained by Gibbs formula.The variation of interfacial energy caused by adsorption as well as the relationship between the relation curve and the type of adsorption was discussed.

Leaching kinetics of zinc silicate in ammonium chloride solution

The leaching kinetics of zinc silicate in ammonium chloride solution was investigated. The effects of stirring speed （150？400 r/min）, leaching temperature （95-108 ℃, particle size of zinc silicate （61-150 μm） and the concentration of ammonium chloride （3.5-5.5 mol/L） on leaching rate of zinc were studied. The results show that decreasing the particle size of zinc silicate and increasing the leaching temperature and concentration of ammonium chloride can obviously enhance the leaching rate of zinc. Among the kinetic models of the porous solids tested, the grain model with porous diffusion control can well describe the zinc leaching kinetics. The apparent activation energy of the leaching reaction is 161.26 kJ/mol and the reaction order with respect to ammonium chloride is 3.5.

Self-healing mechanism of composite coatings obtained by phosphating and silicate sol post-sealing

Silicate sol post-treatment was applied to form a complete composite coating on the phosphated zinc layer. The chemical compositions of the coatings were investigated using XPS. The coated samples were firstly scratched and then exposed to the neutral salt spray(NSS) chamber for different time. The microstructure and chemical compositions of the scratches were studied using SEM and EDS. And the non-scratched coated samples were compared. The self-healing mechanism of the composite coatings was discussed. The results show that during corrosion, the self-healing ions in composite coatings dissolve, diffuse and transfer to the scratches or the defects, and then recombine with Zn2+ to form insoluble compound, which deposits and covers the exposed zinc. The corrosion products on the scratches contain silicon, phosphorous, oxygen, chloride and zinc, and they are compact, fine, needle and flake, effectively inhibiting the corrosion formation and expansion of the exposed zinc layer. The composite coatings have good self-healing ability.

Influence of sodium silicate on manganese electrodeposition in sulfate solution

The influences of sodium silicate on manganese electrodeposition in sulfate solution were investigated. Manganese electrodeposition experiments indicate that a certain amount of sodium silicate can improve cathode current efficiency and initial pH 7.0?8.0 is the optimized pH for high cathode current efficiency. The analyses of scanning electron microscopy (SEM) and X-ray diffraction (XRD) indicate the compact morphology and nanocrystalline structure of electrodeposits. X-ray photoelectron spectrometry (XPS) analysis shows that the elements of Mn, Si and O exist in the deposit. The solution chemistry calculations of sulfate electrolyte and sodium silicate solution indicate that species of Mn2+, MnSO4, Mn(SO4)2?2 , Mn2+, MnSiO3, Mn(NH3)2+, SiO32?and HSiO3? are the main active species during the process of manganese electrodeposition. The reaction trend between Mn2+ and Si-containing ions is confirmed by the thermodynamic analysis. In addition, polarization curve tests confirm that sodium silicate can increase the overpotential of hydrogen evolution reaction, and then indirectly improve the cathode current efficiency.

Local structure of calcium silicate melts from classical molecular dynamics simulation and a newly constructed thermodynamic model

The distributions of local structural units of calcium silicate melts were quantified by means of classical molecular dynamics simulation and a newly constructed structural thermodynamic model. The distribution of five kinds of Si-O tetrahedra Qi from these two methods was compared with each other and also with the experimental Raman spectra, an excellent agreement was achieved. These not only displayed the panorama distribution of microstructural units in the whole composition range, but also proved that the thermodynamic model is suitable for the utilization as the subsequent application model of spectral experiments for the thermodynamic calculation. Meanwhile, the five refined regions mastered by different disproportionating reactions were obtained. Finally, the distributions of two kinds of connections between Qi were obtained, denoted as Qi-Ca-Qj and Qi-[Ob]-Qj, from the thermodynamic model, and a theoretical verification was given that the dominant connections for any composition are equivalent connections.

Preparation and characterization of manganese - containing silicates with Z S M - 48 structure

报道了新型杂原子分子筛Ｍｎ－ＺＳＭ－４８的合成与表征。红外光谱和紫外漫反射光谱测试表明Ｍｎ（Ⅱ）离子进入了分子筛骨架。Ｍｎ（Ⅱ）同晶取代Ｓｉ（Ⅳ）导致产物晶粒的形貌和热性质有所不同。反应混合物中１，６－己二胺的含量，水含量和ＳｉＭｎ比对产物的晶化有很大影响。

Fractionation and solubility of cadmium in paddy soils amended with porous hydrated calcium silicate

Previous studies have shown that porous hydrated calcium silicate （PS） is very effective in decreasing cadmium （Cd） content in brown rice. However, it is unclear whether the PS influences cadmium transformation in soil. The present study examined the effect of PS on pH, cadmium transformation and cadmium solubility in Andosol and Alluvial soil, and also compared its effects with CaCO3, acidic porous hydrated calcium silicate （APS） and silica gel. Soil cadmium was operationally fractionationed into exchangeable （Exch）, bound to carbonates （Carb）, bound to iron and manganese oxides （FeMnOx）, bound to organic matters （OM） and residual （Res） fraction. Application of PS and CaCO3 at hig rates enhanced soil pH, while APS and silica gel did not obviously change soil pH. PS and CaCO3 also increased the FeMnOx-Cd in Andosol and Carb-Cd in Alluvial soil, thus reducing the Exch-Cd in the tested soils. However, PS was less effective than CaCO3 at the same application rate. Cadmium fractions in the two soils were not changed by the treatments of APS and silica gel. There were no obvious differences in the solubility of cadmium in soils treated with PS, APS, silica gel and CaCO3 except Andosol treated 2.0% CaCO3 at the same pH of soil-CaC12 suspensions. These findings suggested that the decrease of cadmium availability in soil was mainly attributed to the increase of soil pH caused by PS.

Adsorption of Methylene Blue on magnesium silicate: Kinetics, equilibria and comparison with other adsorbents

Batch adsorption from aqueous solutions in a slightly basic medium of Methylene Blue, up to 2500 mg/L, onto synthetic magnesium silicate （Florisil） of three particle size ranges （mean diameters of 112, 200 and 425 μm） was compared to the corresponding adsorption onto activated carbon and Amberlite XAD-2. The best fit of the kinetic results was achieved by a pseudo second-order equation. The equilibrium data were found to be well represented by the Langmuir isotherm equation. Amberlite XAD-2, an unspecific adsorbent capable of adsorbing exclusively through a surface effect, exhibited a poor dye uptake, confirming that the adsorption mechanism on Florisil was due to electrostatic attraction and ion exchange. Moreover, the comparison between Florisil and the other adsorbents was performed on the basis of the evaluation of the surface area and pore volume occupied by the adsorbed dye.

Occurrence mechanism of silicate and aluminosilicate minerals in Sarcheshmeh copper flotation concentrate

The Sarcheshmeh copper flotation circuit is producing 5× 10^4 t copper concentrate per month with an averaging grade of 28% Cu in rougher, cleaner and recleaner stages. In recent years, with the increase in the open pit depth, the content of aluminosilicate minerals increased in plant feed and subsequently in flotation concentrate. It can motivate some problems, such as unwanted consumption of reagents, decreasing of the copper concentrate grade, increasing of Al2O3 and SiO2 in the copper concentrate, and needing a higher temperature in the smelting process. The evaluation of the composite samples related to the most critical working period of the plant shows that quartz, illite, biotite, chlorite, orthoclase, albeit, muscovite, and kaolinite are the major Al2O3 and SiO2 beating minerals that accompany chalcopyrite, chalcocite, and covellite minerals in the plant feed. The severe alteration to clay minerals was a general rule in all thin sections that were prepared from the plant feed. Sieve analysis of the flotation concentrate shows that Al2O3 and SiO2 bearing minerals in the flotation concentrate can be decreased by promoting the size reduction from 53 to 38 μm. Interlocking of the Al2O3 and SiO2 bearing minerals with chalcopyrite and chalcocite is the occurrence mechanism of silicate and aluminosilicate minerals in the flotation concentrate. The dispersed form of interlocking is predominant.

Identification and Practical Application of Silicate-dissolving Bacteria

Slime-forming bacteria were isolated from soils, rock surface and earthworm intestine, and their effects on dissolving silicate minerals and tomato growth were examined. One of the bacteria, Bacillus mucilaginosus RGBc13, had particularly strong ability to form slime and dissolve silicates. RGBc13 could also colonize and develop in both non-rhizosphere and rhizosphere soil. Total number of slime-forming bacteria increased from 2.9 × 103 cfu·g-1and 8.4 × 103 cfu·g-1 to 9.6 × 106 cfu·g-1 and 6.0 × 107 cfu·g-1 in the non-rhizosphere and rhizosphere soils respectively. Potassium and phosphorus nutritional conditions in the rhizosphere were markedly improved through inoculation of this bacterium. Available K and P respectively increased from 25. 86 and 3. 63mg · kg-1 in the non-rhizosphere soil to 91. 23 and 5. 74mg · kg-1 in the rhizosphere soil. Tomato biomass increased by 125%, K and P uptakes were more than 150%, greater than the non-inoculation. Thus, there is a potential in applying RGBcl3 for improving plant K and P nutrition.

Properties and coagulation mechanisms of polyferric silicate sulfate with high concentration

Polyferric silicate sulfate （PFSS） with high concentration was prepared using the composite-poly method. The coagulation properties and mechanisms of this new complex were probed using TEM, Fe-Ferron timed complex-colorimetric method, and infrared spectrum method. The results showed that the flocculating effect of polyferric silicate sulfate had an advantage over polyferric sulfate （PFS）, as the optimum coagulation effect could be obtained when the Si/Fe mole ratio was 0.75 in accordance with its macrostructure of PFSS. According to the Fe-Ferron timed complex-colorimetric method, the Si species was mainly Sic, whereas, the Fe species were Fea and Fec in the copolymerization system. The infrared spectra indicated that the structure of these new flocculants was formed by polymers, mainly by olation, which was different from polyferric sulfate, and the vibration of M-OH-M of around 1100 cm^-1, also proved that there existed Fe-OH-Fe and its polymers in some forms.

Interactions between Bacillus mucilaginosus and silicate minerals(weathered adamellite and feldspar):Weathering rate,products,and reaction mechanisms

Bacillus mucilaginosus is a common soil bacterium,and usually used as a model bacterium in studying microbe-mineral interactions.Several reaction mechanisms of B.mucilaginosus weathering silicate minerals were proposed.However,the molecule mechanisms and detailed processes were still unclear.In this paper,bacterium-mineral interactions were studied in terms of variations in pH value over the experimental period,variations in mineral composition,weathering rates of silicate minerals and volatile metabolites in the culture medium,etc.,to further explore the bacterium-mineral interaction mechanisms.The results showed that B.mucilaginosus could enhance silicate mineral weathering obviously.The weathering rates were quite different for various kinds of silicate minerals,and the weathering rate of weathered adamellite could reach 150 mg/m2/d.Although B.mucilaginosus produced little acidic substance,pH in the microenvironment of bacterium-mineral complex might be far lower than that of the circumjacent environment;a large amount of acetic acid was found in the metabolites,and was likely to play an important role as a ligand.These results appear to suggest that acidolysis and ligand degradation are the main mechanisms of B.mucilaginosus dissolving silicate minerals,the formation of bacterium-mineral complexes is the necessary condition for the bacteria weathering silicate minerals,and extracelluar polysaccharides played important roles in bacterium-mineral interaction processes by forming bacterium-mineral complexes and maintaining the spe-cial physicochemical properties of microenvironment.

Effect of C/S Ratio on Morphology and Structure of Hydrothermally Synthesized Calcium Silicate Hydrate

The samples of the C-S-H series were synthesized by hydrothermal reaction of fumed silica, CaO and deionized water at initial C/S ratios between 1.0-1.7. Phase composition and structural and morphology characteristics of C-S-H samples were analyzed by XRD, IR and SEM. The experimental results showed that the d-spacing of （002）, （110） and （020） decreased, the d-spacing of （200） increased, and the d-spacing of （310） varied randomly, the polymerization of silica tetrahedra of C-S-H decreased, and morphology of C-S-H samples varied from sheet shapes to long reticular fibers as C/S ratio increased.

Dry reusing and wet reclaiming of used sodium silicate sand

Based on the characteristics of used sodium silicate sand and the different use requirements for recycled sand, "dry reusing and wet reclaiming of used sodium silicate sand" is considered as the most suitable technique for the used sand. When the recycled sand is used as support sand, the used sand is only reused by dry process including breaking, screening, dust-removal, etc., and it is not necessary that the used sand is reclaimed with strongly rubbing and scraping method, but when the recycled sand is used as facing sand (or single sand), the used sand must be reclaimed by wet method for higher removal rate of the residual binders. The characteristics and the properties of the dry reused sand are compared with the wet reclaimed sand after combining the different use requirements of support sand and facing sand (or single sand), and above the most adaptive scheme has also been validated.

Adjuvant effect of a synthetic Aluminium-Magnesium Silicate on chloroquine phosphate, against Plasmodium berghei

Effect a synthetic Aluminium-Magnesium Silicate (AMS) has on chloroquine was tested. Thirty, Plasmodium berghei-infected mice, in three experimental groups (7 mg/kg, 5 mg/kg and 3 mg/kg) of 10 mice each, were treated. Two subgroups, in each experiment, were treated with chloroquine and with a chloroquine-AMS drug formulation, respectively. Five of the infected mice served as controls. Parasitaemia (%), Haemoglobin concentration (Hb), Red Blood Cells (RBC), rectal temperature and body weight were assessed. Parasitaemia of subgroups treated at 7 mg/kg were higher than that of the control. Also, at 7 mg/kg, there was mortality with chloroquine (20%) and with the chloroquine-AMS drug (80%). At 5 mg/kg and 3 mg/kg, the AMS significantly (P < 0.05) improved ability of chloroquine to reduce plamodial parasitaemia, from 2.46 ± 0.21 to 1.57 ± 0.25 and from 3.82 ± 0.06 to 2.12 ± 0.08. It also significantly (P < 0.05) improved means of Hb and RBC from 12.25 ± 0.27 and 88.99 ± 5.72 to 12.68 ± 0.18 and 92.91 ± 4.01 and from 10.18 ± 3.00 and 63.39 ± 18.02 to 12.98 ± 0.47 and 95.23 ± 5.32. Body weight increased at 5 mg/kg, from 29.06 ± 1.95 to 32.66 ± 2.10 kg (P < 0.05) while at 3 mg/kg, rectal temperature reduced from 37.35 ± 0.32 to 36.84oC ± 0.23oC (P < 0.05). These results suggest, AMS worsened chloroquine toxicity at 7 mg/kg but potentiated its antiplasmodial activities at the lower doses.