Polypropylene composites of snail shell powder were prepared at filler contents, 0 to 40 wt%. The particle sizes of the snail shell powder investigated were 0.150, 0.30, and 0.42 μm. Talc, of particle size, 0.150 μm...Polypropylene composites of snail shell powder were prepared at filler contents, 0 to 40 wt%. The particle sizes of the snail shell powder investigated were 0.150, 0.30, and 0.42 μm. Talc, of particle size, 0.150 μm was used as the reference filler. The polypropylene composites were prepared in an injection moulding machine and the resulting composites were extruded as sheets. Some mechanical and end-use properties of the prepared composites were determined. Results showed that the snail shell powder improved the tensile modulus, flexural strength, and impact strength of polypropylene and these properties increased with increases in the filler content and decreases in the filler particle size. The elongation at break of the composites was however observed to decrease with increases in the filler content, and particle size. The elongation at break of talc filled polypropylene was zero, an indication of the brittle nature of polypropylene composites of talc. The hardness, water sorption (24-hr) and specific gravity of the composites were found to increase with increases in the filler content, and decreases in the filler particle size. The level of water absorbed by snail shell powder composites of polypropylene is considerably higher than that of talc filled polypropylene. The flame retardant properties of the prepared composites were however found to decrease with increases in the filler content, and particle size. Generally, snail shell powder was found to show greater property improvement over talc in the prepared composites.展开更多
【目的】为研究混合锂离子超级电容器(hybrid lithium ion supercapacitor,HLIC)的性能,分析多种干扰因素对其电化学与热特性的影响。【方法】首先建立HLIC电化学热耦合模型;其次通过试验与数值模拟相互验证来证明模型的可靠性;最后分...【目的】为研究混合锂离子超级电容器(hybrid lithium ion supercapacitor,HLIC)的性能,分析多种干扰因素对其电化学与热特性的影响。【方法】首先建立HLIC电化学热耦合模型;其次通过试验与数值模拟相互验证来证明模型的可靠性;最后分析阳极活性材料颗粒粒径、充放电倍率、电芯结构状态对HLIC的电化学与热特性的影响,并通过建立核壳模型绘制核壳图,从微观的角度分析了阳极活性材料颗粒粒径对HLIC电化学性能的影响过程。【结果】HLIC在高倍率的条件下,减小粒径可使阳极活性材料颗粒锂化程度显著提高,10 C倍率下粒径15.5μm与0.5μm的单体相比,前者能量密度降低了63.14%,平均发热率增加了121.66%,最大温度上升了17.7 K;而在低倍率的条件下,粒径对HLIC的性能影响不大,无须增加成本过分减小粒径,并且电芯在层压方向导热性较差,需要在层压方向上增加散热以保证其工作性能良好。【结论】本研究对各个场景所需的HLIC性能参数的选取具有一定的参考意义。展开更多
Silica sol prepared by sol-gel method was introduced into poly (butyl acrylate) (PBA)/poly (butyl acrylate-styrene-methacryloxypropyl trimethoxysilane) (PSBM) core-shell emulsions to prepare a series of paper surface ...Silica sol prepared by sol-gel method was introduced into poly (butyl acrylate) (PBA)/poly (butyl acrylate-styrene-methacryloxypropyl trimethoxysilane) (PSBM) core-shell emulsions to prepare a series of paper surface sizing agents. The rheological measurement indicated that PSBM emulsions exhibited shear-thinning behavior, and the phenomena became more pronounced with increasing silica sol concentration. Dynamic mechanical analysis (DMA) demonstrated that the stronger interfacial interaction between silica sol and polymer matrix, but microphase separation took place with excess silica sol. Thereby the tensile strength and thermal stability of emulsion films were increased with desirable silica sol concentration, and when silica sol concentration was greater than 6 wt%, the tensile strength leveled off and the decomposition temperature decreased from 351.19℃ to 331.63℃. The degree of crystallinity increased from 5.12% to 10.98% with 4% silica sol addition, resulting in enhanced rigidity of films. Furthermore, the interaction between polymer and fiber was improved with certain amount of silica sol, resulting in improved sizing degree, ring crush strength, surface strength and folding strength. However, excessive crosslinking will be harmful for the properties of sized paper.展开更多
Walnuts are one of nature’s more waste-heavy products. 67% of the nut is shell and husk, low value by-products that are rich in phenolic compounds. The phenolic compounds extracted from walnut shells are potentially ...Walnuts are one of nature’s more waste-heavy products. 67% of the nut is shell and husk, low value by-products that are rich in phenolic compounds. The phenolic compounds extracted from walnut shells are potentially good natural sources of antioxidants for the food and pharmaceutical industries. In this study, phenolic compounds were extracted using an ultrasonic bath, an ultrasonic probe and a standard shaking method. The extraction yield achieved with an ultrasonic probe was 51.2 mg GAE/g DW, two times higher than both the shaking method and the ultrasonic bath method which were 20.6 mg GAE/g DW and 25.8 mg GAE/g DW, respectively. Phenolic extraction was further improved by a size reduction of the walnut shells. The best extraction yield of 52.8 mg GAE/g DW was attained when the particle size was between 45 - 100 mesh. The ultrasonic probe treatment is the best method for extraction of phenolic compounds from walnut shells. Scanning electron microscopy (SEM) imaging indicated that the ultrasonic probe treatment could better rupture the hard structure of the cells, increasing the penetration of solvents and thus the extraction yield.展开更多
文摘Polypropylene composites of snail shell powder were prepared at filler contents, 0 to 40 wt%. The particle sizes of the snail shell powder investigated were 0.150, 0.30, and 0.42 μm. Talc, of particle size, 0.150 μm was used as the reference filler. The polypropylene composites were prepared in an injection moulding machine and the resulting composites were extruded as sheets. Some mechanical and end-use properties of the prepared composites were determined. Results showed that the snail shell powder improved the tensile modulus, flexural strength, and impact strength of polypropylene and these properties increased with increases in the filler content and decreases in the filler particle size. The elongation at break of the composites was however observed to decrease with increases in the filler content, and particle size. The elongation at break of talc filled polypropylene was zero, an indication of the brittle nature of polypropylene composites of talc. The hardness, water sorption (24-hr) and specific gravity of the composites were found to increase with increases in the filler content, and decreases in the filler particle size. The level of water absorbed by snail shell powder composites of polypropylene is considerably higher than that of talc filled polypropylene. The flame retardant properties of the prepared composites were however found to decrease with increases in the filler content, and particle size. Generally, snail shell powder was found to show greater property improvement over talc in the prepared composites.
文摘Silica sol prepared by sol-gel method was introduced into poly (butyl acrylate) (PBA)/poly (butyl acrylate-styrene-methacryloxypropyl trimethoxysilane) (PSBM) core-shell emulsions to prepare a series of paper surface sizing agents. The rheological measurement indicated that PSBM emulsions exhibited shear-thinning behavior, and the phenomena became more pronounced with increasing silica sol concentration. Dynamic mechanical analysis (DMA) demonstrated that the stronger interfacial interaction between silica sol and polymer matrix, but microphase separation took place with excess silica sol. Thereby the tensile strength and thermal stability of emulsion films were increased with desirable silica sol concentration, and when silica sol concentration was greater than 6 wt%, the tensile strength leveled off and the decomposition temperature decreased from 351.19℃ to 331.63℃. The degree of crystallinity increased from 5.12% to 10.98% with 4% silica sol addition, resulting in enhanced rigidity of films. Furthermore, the interaction between polymer and fiber was improved with certain amount of silica sol, resulting in improved sizing degree, ring crush strength, surface strength and folding strength. However, excessive crosslinking will be harmful for the properties of sized paper.
文摘Walnuts are one of nature’s more waste-heavy products. 67% of the nut is shell and husk, low value by-products that are rich in phenolic compounds. The phenolic compounds extracted from walnut shells are potentially good natural sources of antioxidants for the food and pharmaceutical industries. In this study, phenolic compounds were extracted using an ultrasonic bath, an ultrasonic probe and a standard shaking method. The extraction yield achieved with an ultrasonic probe was 51.2 mg GAE/g DW, two times higher than both the shaking method and the ultrasonic bath method which were 20.6 mg GAE/g DW and 25.8 mg GAE/g DW, respectively. Phenolic extraction was further improved by a size reduction of the walnut shells. The best extraction yield of 52.8 mg GAE/g DW was attained when the particle size was between 45 - 100 mesh. The ultrasonic probe treatment is the best method for extraction of phenolic compounds from walnut shells. Scanning electron microscopy (SEM) imaging indicated that the ultrasonic probe treatment could better rupture the hard structure of the cells, increasing the penetration of solvents and thus the extraction yield.
