The present study is concerned with the effect of filler metals such as austenitic stainless steel, ferritic stainless steel and duplex stainless steel on tensile and impact properties of the ferritic stainless steel ...The present study is concerned with the effect of filler metals such as austenitic stainless steel, ferritic stainless steel and duplex stainless steel on tensile and impact properties of the ferritic stainless steel conforming to AISI 409M grade. Rolled plates of 4 mm thickness were used as the base material for preparing single pass butt welded joints. Tensile and impact properties, microhardness, microstructure and fracture surface morphology of the joints fabricated by austenitic stainless steel, ferritic stainless steel and duplex stainless steel filler metals were evaluated and the results were reported. From this investigation, it is found that the joints fabricated by duplex stainless steel filler metal showed higher tensile strength and hardness compared to the joints fabricated by austenitic and ferritic stainless steel filler metals. Joints fabricated by austenitic stainless steel filler metal exhibited higher ductility and impact toughness compared with the joints fabricated by ferritic stainless steel and duplex stainless steel filler metals.展开更多
The microstructure in the weld metals for HQ130 + QJ63 high strength steels,which are welded by Ar-CO_2 gas shielded metal arc welding,was analyzed by means of microscope and scan electron microscope(SEM).The relative...The microstructure in the weld metals for HQ130 + QJ63 high strength steels,which are welded by Ar-CO_2 gas shielded metal arc welding,was analyzed by means of microscope and scan electron microscope(SEM).The relative content of different microstructure was evaluated with XQF-2000 micro-image analyzer.The effect of acicular ferrite content on the impact toughness was also studied.The test results indicated that the main microstructure in the weld metals of HQ130 + QJ63 high strength steels is acicular ferrite and a few pro-eutectic ferrite on the boundary of original austenite grain.Near the fusion zone there are columnar grains whose direction coefficient(X) is 3.22,but the microstructure in the center of the weld metal is isometric grain,whose direction coefficient X = 1.In order to avoid welding crack and improve welding technology the weld heat input should be strictly controlled in 10-16 kJ/cm.Thus,the main microstructure in the weld metals is fine acicular ferrite and the content of pro-eutectic ferrite is limited.The impact toughness in the weld metals of HQ130+ QJ63 steels can be ensured and can meet the requirements for application in engineering and machinery.展开更多
The microstructure in the weld metals for HQ130+QJ63 high strength steels, which are welded by Ar CO 2 gas shielded metal arc welding, was analyzed by means of microscope and scan electron microscope (SEM). The rela...The microstructure in the weld metals for HQ130+QJ63 high strength steels, which are welded by Ar CO 2 gas shielded metal arc welding, was analyzed by means of microscope and scan electron microscope (SEM). The relative content of different microstructure was evaluated with XQF 2000 micro image analyzer. The effect of acicular ferrite content on the impact toughness was also studied. The test results indicated that the main microstructure in the weld metals of HQ130+QJ63 high strength steels is acicular ferrite and a few pro eutectic ferrite on the boundary of original austenite grain. Near the fusion zone there are columnar grains whose direction coefficient (X) is 3 22, but the microstructure in the center of the weld metal is isometric grain, whose direction coefficient X=1 In order to avoid welding crack and improve welding technology the weld heat input should be strictly controlled in 10-16 kJ/cm. Thus, the main microstructure in the weld metals is fine acicular ferrite and the content of pro eutectic ferrite is limited. The impact toughness in the weld metals of HQ130+QJ63 steels can be ensured and can meet the requirements for application in engineering and machinery.展开更多
The effect of welding processes such as shielded metal arc welding, gas metal arc welding and gas tungsten arc welding on tensile and impact properties of the ferritic stainless steel conforming to AISI 409M grade is ...The effect of welding processes such as shielded metal arc welding, gas metal arc welding and gas tungsten arc welding on tensile and impact properties of the ferritic stainless steel conforming to AISI 409M grade is studied. Rolled plates of 4 mm thickness were used as the base material for preparing single pass butt welded joints. Tensile and impact properties, microhardness, microstructure and fracture surface morphology of the welded joints have been evaluated and the results are compared. From this investigatio.n, it is found that gas tungsten arc welded joints of ferritic stainless steel have superior tensile and impact properties compared with shielded metal arc and gas metal arc welded joints and this is mainly due to the presence of finer grains in fusion zone and heat affected zone.展开更多
Welding of high strength low alloy steels (HSLA) involves usage of low, even and high strength filler materials (electrodes) than the parent material depending on the application of the welded structures and the avail...Welding of high strength low alloy steels (HSLA) involves usage of low, even and high strength filler materials (electrodes) than the parent material depending on the application of the welded structures and the availability of the filler material. In the present investigation, the fatigue crack growth behaviour of weld metal (WM) and heat affected zone (HAZ) regions of under matched (UM), equal matched (EM) and over matched (OM) joints has been studied. The base material used in this investigation is HSLA-80 steel of weldable grade. Shielded metal arc welding (SMAW) process has been used to fabricate the butt joints. Centre cracked tension (CCT) specimen has been used to evaluate the fatigue crack growth behaviour of the welded joints. Fatigue crack growth experiments have been conducted using servo hydraulic controlled fatigue testing machine at constant amplitude loading (R=0).A method has been proposed to predict the fatigue life of HSLA steel welds using fracture mechanics approach by incorporating influences of mismatch ratio (MMR) and notch location.展开更多
Quenched and tempered steels are prone to hydrogen induced cracking in the heat affected zone after welding. The use of austenitic stainless steel consumables to weld the above steel was the only available remedy beca...Quenched and tempered steels are prone to hydrogen induced cracking in the heat affected zone after welding. The use of austenitic stainless steel consumables to weld the above steel was the only available remedy because of higher solubility for hydrogen in austenitic phase. In this investigation, an attempt was made to determine a suitable consumable to replace expensive austenitic consumables. Two different consumables, namely, austenitie stain less steel and low hydrogen ferritic steel, were used to fabricate the joints by shielded metal are welding (SMAW) and flux cored arc welding (FCAW) processes. The joints fabricated by using low hydrogen ferritic steel consumables showed superior transverse tensile properties, whereas joints fabricated by using austenitic stainless steel consumables exhibited better impact toughness, irrespective of the welding process used. The SMAW joints exhibited superior mechanical and impact properties, irrespective of the consumables used, than their FCAW counterparts.展开更多
The weldability of a ferritic ductile cast iron was investigated as a function of different consumables and welding conditions. A 23 full factorial experimental design was used to analyze the effect of factors and the...The weldability of a ferritic ductile cast iron was investigated as a function of different consumables and welding conditions. A 23 full factorial experimental design was used to analyze the effect of factors and their interac- tions on ultimate tensile strength of weldments. The shielded metal arc welding (SMAW) process was used with two types of consumables (E7018 and ENi-CI) under eight different conditions using as-cast samples. The microstructur- al evolution and fracture mechanisms were investigated by optical microscopy and scanning electron microscopy (SEM), respectively. The hardness, tensile and impact tests were also performed to determine the weld quality. Based on experiment design, preheat, consumable, cooling condition, preheat cooling and preheat-consumable inter- actions were significant factors. Preheat is the most effective factor and in the case of E7018, preheat and cooling conditions were the most sensible factors. It was found that buttering was the most appropriate welding method for ferritic ductile cast iron.展开更多
Combat vehicles using armour grade quenched and tempered (Q&T) steel are needed to be operated under different climatic conditions. However, the properties meeting the room temperature test conditions may not neces...Combat vehicles using armour grade quenched and tempered (Q&T) steel are needed to be operated under different climatic conditions. However, the properties meeting the room temperature test conditions may not neces-sarily be required to meet the low temperature operating conditions. The influences of shielded metal arc welding (SMAW) process, flux cored arc welding (FCAW) processes and test temperatures below room temperature up to 60℃ on tensile and impact toughness properties of armour grade Q&T steel welds were reported. The tensile and impact properties of the joints showed incremental trend with respect to the decrement in test temperature up to -40℃ irrespective of the welding processes used. The increment in tensile and impact properties of SMAW and FCAW joints subjected to the low temperature environment is due to plastic strain-induced phase transformation of retained austenite into martensite phase. Among the two processes, SMAW process welded joint showed better tensile and impact properties than its FCAW counterpart joints.展开更多
文摘The present study is concerned with the effect of filler metals such as austenitic stainless steel, ferritic stainless steel and duplex stainless steel on tensile and impact properties of the ferritic stainless steel conforming to AISI 409M grade. Rolled plates of 4 mm thickness were used as the base material for preparing single pass butt welded joints. Tensile and impact properties, microhardness, microstructure and fracture surface morphology of the joints fabricated by austenitic stainless steel, ferritic stainless steel and duplex stainless steel filler metals were evaluated and the results were reported. From this investigation, it is found that the joints fabricated by duplex stainless steel filler metal showed higher tensile strength and hardness compared to the joints fabricated by austenitic and ferritic stainless steel filler metals. Joints fabricated by austenitic stainless steel filler metal exhibited higher ductility and impact toughness compared with the joints fabricated by ferritic stainless steel and duplex stainless steel filler metals.
基金supported by the visting scholar foundation of the National Key Laboratory of the Advanced Welding Production Technology,Harbin Institute of Technology,P.R.China
文摘The microstructure in the weld metals for HQ130 + QJ63 high strength steels,which are welded by Ar-CO_2 gas shielded metal arc welding,was analyzed by means of microscope and scan electron microscope(SEM).The relative content of different microstructure was evaluated with XQF-2000 micro-image analyzer.The effect of acicular ferrite content on the impact toughness was also studied.The test results indicated that the main microstructure in the weld metals of HQ130 + QJ63 high strength steels is acicular ferrite and a few pro-eutectic ferrite on the boundary of original austenite grain.Near the fusion zone there are columnar grains whose direction coefficient(X) is 3.22,but the microstructure in the center of the weld metal is isometric grain,whose direction coefficient X = 1.In order to avoid welding crack and improve welding technology the weld heat input should be strictly controlled in 10-16 kJ/cm.Thus,the main microstructure in the weld metals is fine acicular ferrite and the content of pro-eutectic ferrite is limited.The impact toughness in the weld metals of HQ130+ QJ63 steels can be ensured and can meet the requirements for application in engineering and machinery.
基金Sponsored by National Key Fundamental Research Development Project(G1998061513)
文摘The microstructure in the weld metals for HQ130+QJ63 high strength steels, which are welded by Ar CO 2 gas shielded metal arc welding, was analyzed by means of microscope and scan electron microscope (SEM). The relative content of different microstructure was evaluated with XQF 2000 micro image analyzer. The effect of acicular ferrite content on the impact toughness was also studied. The test results indicated that the main microstructure in the weld metals of HQ130+QJ63 high strength steels is acicular ferrite and a few pro eutectic ferrite on the boundary of original austenite grain. Near the fusion zone there are columnar grains whose direction coefficient (X) is 3 22, but the microstructure in the center of the weld metal is isometric grain, whose direction coefficient X=1 In order to avoid welding crack and improve welding technology the weld heat input should be strictly controlled in 10-16 kJ/cm. Thus, the main microstructure in the weld metals is fine acicular ferrite and the content of pro eutectic ferrite is limited. The impact toughness in the weld metals of HQ130+QJ63 steels can be ensured and can meet the requirements for application in engineering and machinery.
文摘The effect of welding processes such as shielded metal arc welding, gas metal arc welding and gas tungsten arc welding on tensile and impact properties of the ferritic stainless steel conforming to AISI 409M grade is studied. Rolled plates of 4 mm thickness were used as the base material for preparing single pass butt welded joints. Tensile and impact properties, microhardness, microstructure and fracture surface morphology of the welded joints have been evaluated and the results are compared. From this investigatio.n, it is found that gas tungsten arc welded joints of ferritic stainless steel have superior tensile and impact properties compared with shielded metal arc and gas metal arc welded joints and this is mainly due to the presence of finer grains in fusion zone and heat affected zone.
文摘Welding of high strength low alloy steels (HSLA) involves usage of low, even and high strength filler materials (electrodes) than the parent material depending on the application of the welded structures and the availability of the filler material. In the present investigation, the fatigue crack growth behaviour of weld metal (WM) and heat affected zone (HAZ) regions of under matched (UM), equal matched (EM) and over matched (OM) joints has been studied. The base material used in this investigation is HSLA-80 steel of weldable grade. Shielded metal arc welding (SMAW) process has been used to fabricate the butt joints. Centre cracked tension (CCT) specimen has been used to evaluate the fatigue crack growth behaviour of the welded joints. Fatigue crack growth experiments have been conducted using servo hydraulic controlled fatigue testing machine at constant amplitude loading (R=0).A method has been proposed to predict the fatigue life of HSLA steel welds using fracture mechanics approach by incorporating influences of mismatch ratio (MMR) and notch location.
文摘Quenched and tempered steels are prone to hydrogen induced cracking in the heat affected zone after welding. The use of austenitic stainless steel consumables to weld the above steel was the only available remedy because of higher solubility for hydrogen in austenitic phase. In this investigation, an attempt was made to determine a suitable consumable to replace expensive austenitic consumables. Two different consumables, namely, austenitie stain less steel and low hydrogen ferritic steel, were used to fabricate the joints by shielded metal are welding (SMAW) and flux cored arc welding (FCAW) processes. The joints fabricated by using low hydrogen ferritic steel consumables showed superior transverse tensile properties, whereas joints fabricated by using austenitic stainless steel consumables exhibited better impact toughness, irrespective of the welding process used. The SMAW joints exhibited superior mechanical and impact properties, irrespective of the consumables used, than their FCAW counterparts.
文摘The weldability of a ferritic ductile cast iron was investigated as a function of different consumables and welding conditions. A 23 full factorial experimental design was used to analyze the effect of factors and their interac- tions on ultimate tensile strength of weldments. The shielded metal arc welding (SMAW) process was used with two types of consumables (E7018 and ENi-CI) under eight different conditions using as-cast samples. The microstructur- al evolution and fracture mechanisms were investigated by optical microscopy and scanning electron microscopy (SEM), respectively. The hardness, tensile and impact tests were also performed to determine the weld quality. Based on experiment design, preheat, consumable, cooling condition, preheat cooling and preheat-consumable inter- actions were significant factors. Preheat is the most effective factor and in the case of E7018, preheat and cooling conditions were the most sensible factors. It was found that buttering was the most appropriate welding method for ferritic ductile cast iron.
基金the Armament Research Board(ARMREB),Directorate of Armaments,Ministry of Defense,New Delhi,Government of India for providing financial support to carry out this investigation through a CARS project,No.CVRDE/MMG/2011-2012/003/CARS dated 23rd May 2011
文摘Combat vehicles using armour grade quenched and tempered (Q&T) steel are needed to be operated under different climatic conditions. However, the properties meeting the room temperature test conditions may not neces-sarily be required to meet the low temperature operating conditions. The influences of shielded metal arc welding (SMAW) process, flux cored arc welding (FCAW) processes and test temperatures below room temperature up to 60℃ on tensile and impact toughness properties of armour grade Q&T steel welds were reported. The tensile and impact properties of the joints showed incremental trend with respect to the decrement in test temperature up to -40℃ irrespective of the welding processes used. The increment in tensile and impact properties of SMAW and FCAW joints subjected to the low temperature environment is due to plastic strain-induced phase transformation of retained austenite into martensite phase. Among the two processes, SMAW process welded joint showed better tensile and impact properties than its FCAW counterpart joints.