Carbon black and carbon fibers of different lengths were introduced in different matrices at different ratios to explore their microwave dielectric properties under 8.2 GHz-12.4 GHz. It is found that the actual dielec...Carbon black and carbon fibers of different lengths were introduced in different matrices at different ratios to explore their microwave dielectric properties under 8.2 GHz-12.4 GHz. It is found that the actual dielectric constants of the samples containing carbon black are in a two-order function of the contents of carbon black （ε＇, ε＂=Av2＋Bv＋C） and the complex dielectric constants show an obvious frequency response. Of the added fibers of different lengths, the 4 mm-long one could well disperse in the matrices having not only good frequency response, but also larger real parts, imaginary parts and loss values. The imaginary parts and the loss values （tanδ）of the samples with 4 mm-long carbon fibers added increase linearly with the contents of fiber increasing. So it is practicable to adjust the dielectric parameters of the material in a wide range by changing the added amount of carbon black, and the carbon fiber or altering the lengths of the carbon fiber added.展开更多
Short carbon fiber preform reinforced geopolymer composites containing different contents of α-Al2O3 filler (Cf(α-Al2O3)/geopolymer composites) were fabricated,and the effects of heat treatment temperatures up to 1 ...Short carbon fiber preform reinforced geopolymer composites containing different contents of α-Al2O3 filler (Cf(α-Al2O3)/geopolymer composites) were fabricated,and the effects of heat treatment temperatures up to 1 200 ℃ on the thermal-mechanical properties were studied. The results show that the thermal shrinkage in the direction perpendicular to the lamination of the composites gradually increases with the increase of the heat treatment temperatures from room temperature (25 ℃) to 1 000 ℃. However,the composites in the direction parallel to the lamination show an expansion behavior. Beyond 1 000 ℃,in the two directions the composites exhibit a larger degree of shrinkage due to the densification and crystallization. The mechanical properties of the composites show the minimum values in the temperature range from 600 to 800 ℃ as the hydration water of geopolymer matrix is lost. The addition of α-Al2O3 particle filler into the composites clearly increases the onset crystalline temperature of leucite (KAlSi2O6) from the amorphous geopolymer matrix. In addition,the addition of α-Al2O3 particles into the composites can not only help to keep volume stable at high temperatures but also effectively improve the mechanical properties of the composites subjected to thermal load to a certain extent. The main toughening mechanisms of the composites subjected to thermal load are attributed to fiber pulling-out.展开更多
Short carbon fiber reinforced AZ91D alloy (Csf/AZ91D) was fabricated by the infiltration-extrusion method. The short carbon fiber preform was infiltrated with melted AZ91D alloy under the assistant of gas pressure. Th...Short carbon fiber reinforced AZ91D alloy (Csf/AZ91D) was fabricated by the infiltration-extrusion method. The short carbon fiber preform was infiltrated with melted AZ91D alloy under the assistant of gas pressure. The extrusion processing was applied following the infiltration processing directly. The tensile property and microstructure of the Csf/AZ91D and that of the die-casting and extruded AZ91D alloy was compared. The results show that the short carbon fiber reinforced AZ91D alloy present excellent tensile property. The tensile strength and modulus of elasticity of Csf/AZ91D is about 50% and 18% higher than that of cast AZ91D alloy, respectively. The elongation to fracture of Csf/AZ91D is about 50% lower than that of AZ91D alloy.展开更多
Short carbon fiber(SCF)reinforced epoxy composites with different SCF contents were developed to investigate their tribological properties.The friction coefficient and wear of the epoxy composites slid in a circular p...Short carbon fiber(SCF)reinforced epoxy composites with different SCF contents were developed to investigate their tribological properties.The friction coefficient and wear of the epoxy composites slid in a circular path against a steel pin inclined at 45°to a vertical axis and a steel ball significantly decreased with increased SCF content due to the solid lubricating effect of SCFs along with the improved mechanical strength of the composites.The scanning electron microscope(SEM)observation showed that the epoxy composites had less sensitive to surface fatigue caused by the repeated sliding of the counterparts than the epoxy.The tribological results clearly showed that the incorporation of SCFs was an effective way to improve the tribological properties of the epoxy composites.展开更多
The spherulites of the short carbon fiber(SCF)/poly(trimethyleneterephthalate)(PTT)compositesformedin limited space at designed temperatures,and their melting behaviors were studied by the polarized optical microscopy...The spherulites of the short carbon fiber(SCF)/poly(trimethyleneterephthalate)(PTT)compositesformedin limited space at designed temperatures,and their melting behaviors were studied by the polarized optical microscopy,atomic force microscopy(AFM),and scanning electron microscopy(SEM),respectively.The results suggest that SCF content,isothermal crystallization temperatures,and the film thicknesses influence the crystal morphology of the composites.The dimension of the spherulites is decreased with increasing SCF content,but whether banded or nonbanded spherulites will form in the composites is not dependent on SCF content.However,the crystal morphology of the composites depends strongly on the temperature.When the isothermal crystallization temperatures increase from 180℃ to 230℃,the crystal morphology of SCF/PTT composites continuously changes in the following order:nonbanded→banded→nonbanded spherulites.Disconti-nuous circle lines form in the film when the film thickness increases from 30 to 60μm.Basing on the SEM observation,it is found that these circle lines are cracks formed due to the constriction difference of the different parts of the spherulites.These cracks are formed when the film is cooled from the isothermal crystallization temperature to the room tempera-ture at a slow cooling rate;while they will disappear gradually at different temperatures in the heating process.The crack will appear/disappear first around the center of the spherulite when the film was cooled/heated.The nontwisted or slightly twisted lamellas will reorganize to form highly twisted lamellas inducing apparent banded texture of the spherulites.展开更多
In order to improve the strength of short carbon fibers reinforced aluminum matrix(Csf/Al)composite,the dispersion of short carbon fibers with multi-orientation was controlled with a square crucible by mechanical stir...In order to improve the strength of short carbon fibers reinforced aluminum matrix(Csf/Al)composite,the dispersion of short carbon fibers with multi-orientation was controlled with a square crucible by mechanical stirring.The three-dimensional flow field models of liquid aluminum melt in the square/round crucibles were established and calculated,and the results were compared.The calculated results show that turbulent flow could be induced both in the square and round crucible,while the non-axisymmetric structure of the square crucible results in higher turbulent kinetic energy in the melt.Therefore,the uniformity and multi-orientation dispersion of the short fibers can be improved by the intensive turbulent flow in the square crucible,which will be increased by increasing the rotational velocity.The distribution of the short carbon fibers in the aluminum matrix prepared under different rotation velocities in square crucible was experimentally investigated.With the increase of stirring velocity,the multi-orientation dispersion of the short fibers in the composites increased gradually.The experimental results are consistent with the calculation results.The tensile testing results show that the strength of the Csf/Al composite can reach 172 MPa when the rotational velocity is 1000 rpm,and it is 48.3%higher than that prepared by the round crucible under the same conditions,which results from the improved multi-orientation dispersion of short carbon fibers in aluminum matrix.展开更多
The field emission current from a carbon fiber is considered. As a model of emission of an elementary carbon tube, tunnel ionization of an electron from a short-range potential is taken. The exact solution for the wav...The field emission current from a carbon fiber is considered. As a model of emission of an elementary carbon tube, tunnel ionization of an electron from a short-range potential is taken. The exact solution for the wave function in such a model allows obtaining an asymptotic expression for electron current. A computer model of transverse distribution of emission current of a carbon fiber is built on the basis of the Monte Carlo method that allows taking into account the random character of distribution of local emitter sources and the distribution of gains of an electric field in carbon nanotubes.展开更多
In addition to the advantage of the lightweight of magnesium alloys, magnesium composites have moderate strength and elastic modulus. The proposed application of magnesium composites as diesel truck pistons makes it n...In addition to the advantage of the lightweight of magnesium alloys, magnesium composites have moderate strength and elastic modulus. The proposed application of magnesium composites as diesel truck pistons makes it necessary to assess their wear performance. Little research data have been discussed on wear behavior of Mg alloy AE42 matrix and its composites. Thus, this paper reports wear behavior of magnesium alloy AE42(Mg–Al–Mn—RE; rare earth) and its composite AE42-C, which contains 23 vol% of randomly oriented carbon short fibers. Materials characterization, including density measurements, hardness testing, microstructures investigation, and compression testing at temperatures of 25, 150,and 300 °C, were conducted. Wear tests were performed under various loads and sliding distances. Wear mechanisms were also proposed based on the examination of worn surfaces using optical microscopy and scanning electron microscopy equipped with EDX(energy-dispersive X-ray spectrometry) analysis system. The hardness of AE42-23 vol% C composite is twice the hardness of the Mg matrix alloy AE42. Significant improvements to yield stress and compressive strength at temperatures of 25, 150, and 300 °C of the composite versus the AE42 alloy are achieved. Wear resistance of the composite is improved considerably versus that of the Mg alloy AE42 at the various sliding distances. Smearing of graphite on the worn surface produces a lubricating film that delays change from mild to severe wear of the composite, especially at high loads. EDX analysis of the worn surface shows oxidation of the matrix alloy at higher wear loads, and this mechanism decreases in the presence of carbon fibers under the same loads. Abrasive wear, oxidation, and plastic deformation are the dominant wear mechanisms for the alloy matrix AE42, whereas mainly abrasive wear is the wear mechanism of AE42-23 vol% C composite under the proposed testing conditions.展开更多
基金National Natural Science Foundation of China (50572090)
文摘Carbon black and carbon fibers of different lengths were introduced in different matrices at different ratios to explore their microwave dielectric properties under 8.2 GHz-12.4 GHz. It is found that the actual dielectric constants of the samples containing carbon black are in a two-order function of the contents of carbon black （ε＇, ε＂=Av2＋Bv＋C） and the complex dielectric constants show an obvious frequency response. Of the added fibers of different lengths, the 4 mm-long one could well disperse in the matrices having not only good frequency response, but also larger real parts, imaginary parts and loss values. The imaginary parts and the loss values （tanδ）of the samples with 4 mm-long carbon fibers added increase linearly with the contents of fiber increasing. So it is practicable to adjust the dielectric parameters of the material in a wide range by changing the added amount of carbon black, and the carbon fiber or altering the lengths of the carbon fiber added.
基金Project supported by the Science Fund for Distinguished Young Scholars of Heilongjiang Province, ChinaProject supported by the Program for Excellent Team in Harbin Institute of Technology
文摘Short carbon fiber preform reinforced geopolymer composites containing different contents of α-Al2O3 filler (Cf(α-Al2O3)/geopolymer composites) were fabricated,and the effects of heat treatment temperatures up to 1 200 ℃ on the thermal-mechanical properties were studied. The results show that the thermal shrinkage in the direction perpendicular to the lamination of the composites gradually increases with the increase of the heat treatment temperatures from room temperature (25 ℃) to 1 000 ℃. However,the composites in the direction parallel to the lamination show an expansion behavior. Beyond 1 000 ℃,in the two directions the composites exhibit a larger degree of shrinkage due to the densification and crystallization. The mechanical properties of the composites show the minimum values in the temperature range from 600 to 800 ℃ as the hydration water of geopolymer matrix is lost. The addition of α-Al2O3 particle filler into the composites clearly increases the onset crystalline temperature of leucite (KAlSi2O6) from the amorphous geopolymer matrix. In addition,the addition of α-Al2O3 particles into the composites can not only help to keep volume stable at high temperatures but also effectively improve the mechanical properties of the composites subjected to thermal load to a certain extent. The main toughening mechanisms of the composites subjected to thermal load are attributed to fiber pulling-out.
基金Supported by the National Natural Science Foundation of China (50575185)the Foundation of Aeronautic Science of China (05G53048)the Natural Science Foundation of Shaanxi Province (2005E23)
文摘Short carbon fiber reinforced AZ91D alloy (Csf/AZ91D) was fabricated by the infiltration-extrusion method. The short carbon fiber preform was infiltrated with melted AZ91D alloy under the assistant of gas pressure. The extrusion processing was applied following the infiltration processing directly. The tensile property and microstructure of the Csf/AZ91D and that of the die-casting and extruded AZ91D alloy was compared. The results show that the short carbon fiber reinforced AZ91D alloy present excellent tensile property. The tensile strength and modulus of elasticity of Csf/AZ91D is about 50% and 18% higher than that of cast AZ91D alloy, respectively. The elongation to fracture of Csf/AZ91D is about 50% lower than that of AZ91D alloy.
基金The authors would like to acknowledge the financial support from the Materials Innovation for Marine and Offshore(MIMO)Program with the grant numbers of SERC1123004028 and SERC1123004032 under the Agency for Science,Technology and Research(A*Star)of Singapore.
文摘Short carbon fiber(SCF)reinforced epoxy composites with different SCF contents were developed to investigate their tribological properties.The friction coefficient and wear of the epoxy composites slid in a circular path against a steel pin inclined at 45°to a vertical axis and a steel ball significantly decreased with increased SCF content due to the solid lubricating effect of SCFs along with the improved mechanical strength of the composites.The scanning electron microscope(SEM)observation showed that the epoxy composites had less sensitive to surface fatigue caused by the repeated sliding of the counterparts than the epoxy.The tribological results clearly showed that the incorporation of SCFs was an effective way to improve the tribological properties of the epoxy composites.
基金The work was supported by the financial support from the Natural Science Foundation of Hebei Province(B2007000148)Hebei University(Y2006065),China.
文摘The spherulites of the short carbon fiber(SCF)/poly(trimethyleneterephthalate)(PTT)compositesformedin limited space at designed temperatures,and their melting behaviors were studied by the polarized optical microscopy,atomic force microscopy(AFM),and scanning electron microscopy(SEM),respectively.The results suggest that SCF content,isothermal crystallization temperatures,and the film thicknesses influence the crystal morphology of the composites.The dimension of the spherulites is decreased with increasing SCF content,but whether banded or nonbanded spherulites will form in the composites is not dependent on SCF content.However,the crystal morphology of the composites depends strongly on the temperature.When the isothermal crystallization temperatures increase from 180℃ to 230℃,the crystal morphology of SCF/PTT composites continuously changes in the following order:nonbanded→banded→nonbanded spherulites.Disconti-nuous circle lines form in the film when the film thickness increases from 30 to 60μm.Basing on the SEM observation,it is found that these circle lines are cracks formed due to the constriction difference of the different parts of the spherulites.These cracks are formed when the film is cooled from the isothermal crystallization temperature to the room tempera-ture at a slow cooling rate;while they will disappear gradually at different temperatures in the heating process.The crack will appear/disappear first around the center of the spherulite when the film was cooled/heated.The nontwisted or slightly twisted lamellas will reorganize to form highly twisted lamellas inducing apparent banded texture of the spherulites.
基金supported financially by the Innovation Team Project of Liaoning Province(No.LT2015020)the Special Professor Project in Liaoning Province.
文摘In order to improve the strength of short carbon fibers reinforced aluminum matrix(Csf/Al)composite,the dispersion of short carbon fibers with multi-orientation was controlled with a square crucible by mechanical stirring.The three-dimensional flow field models of liquid aluminum melt in the square/round crucibles were established and calculated,and the results were compared.The calculated results show that turbulent flow could be induced both in the square and round crucible,while the non-axisymmetric structure of the square crucible results in higher turbulent kinetic energy in the melt.Therefore,the uniformity and multi-orientation dispersion of the short fibers can be improved by the intensive turbulent flow in the square crucible,which will be increased by increasing the rotational velocity.The distribution of the short carbon fibers in the aluminum matrix prepared under different rotation velocities in square crucible was experimentally investigated.With the increase of stirring velocity,the multi-orientation dispersion of the short fibers in the composites increased gradually.The experimental results are consistent with the calculation results.The tensile testing results show that the strength of the Csf/Al composite can reach 172 MPa when the rotational velocity is 1000 rpm,and it is 48.3%higher than that prepared by the round crucible under the same conditions,which results from the improved multi-orientation dispersion of short carbon fibers in aluminum matrix.
文摘The field emission current from a carbon fiber is considered. As a model of emission of an elementary carbon tube, tunnel ionization of an electron from a short-range potential is taken. The exact solution for the wave function in such a model allows obtaining an asymptotic expression for electron current. A computer model of transverse distribution of emission current of a carbon fiber is built on the basis of the Monte Carlo method that allows taking into account the random character of distribution of local emitter sources and the distribution of gains of an electric field in carbon nanotubes.
文摘In addition to the advantage of the lightweight of magnesium alloys, magnesium composites have moderate strength and elastic modulus. The proposed application of magnesium composites as diesel truck pistons makes it necessary to assess their wear performance. Little research data have been discussed on wear behavior of Mg alloy AE42 matrix and its composites. Thus, this paper reports wear behavior of magnesium alloy AE42(Mg–Al–Mn—RE; rare earth) and its composite AE42-C, which contains 23 vol% of randomly oriented carbon short fibers. Materials characterization, including density measurements, hardness testing, microstructures investigation, and compression testing at temperatures of 25, 150,and 300 °C, were conducted. Wear tests were performed under various loads and sliding distances. Wear mechanisms were also proposed based on the examination of worn surfaces using optical microscopy and scanning electron microscopy equipped with EDX(energy-dispersive X-ray spectrometry) analysis system. The hardness of AE42-23 vol% C composite is twice the hardness of the Mg matrix alloy AE42. Significant improvements to yield stress and compressive strength at temperatures of 25, 150, and 300 °C of the composite versus the AE42 alloy are achieved. Wear resistance of the composite is improved considerably versus that of the Mg alloy AE42 at the various sliding distances. Smearing of graphite on the worn surface produces a lubricating film that delays change from mild to severe wear of the composite, especially at high loads. EDX analysis of the worn surface shows oxidation of the matrix alloy at higher wear loads, and this mechanism decreases in the presence of carbon fibers under the same loads. Abrasive wear, oxidation, and plastic deformation are the dominant wear mechanisms for the alloy matrix AE42, whereas mainly abrasive wear is the wear mechanism of AE42-23 vol% C composite under the proposed testing conditions.
