Al-Mg-Si(AA6xxx)series alloys have been used widely in automotive industry for lightweight purpose.This work focuses on developing a short process for manufacturing Al-0.5Mg-1.3Si(wt.%)alloy sheets with good mechanica...Al-Mg-Si(AA6xxx)series alloys have been used widely in automotive industry for lightweight purpose.This work focuses on developing a short process for manufacturing Al-0.5Mg-1.3Si(wt.%)alloy sheets with good mechanical properties.Hereinto,a preparation route without homogenization was proposed on the basis of sub-rapid solidification(SRS)technique.The sample under SRS has fine microstructure and higher average partition coefficients of solute atoms,leading to weaker microsegregation owing to the higher cooling rate(160℃/s)than conventional solidification(CS,30℃/s).Besides,Mg atoms tend to be trapped in Al matrix under SRS,inducing suppression of Mg2Si,and promoting generation of Al Fe Si phase.After being solution heat treated(T4 state),samples following the SRS route have lower yield strength compared with that by CS route,indicating better formability in SRS sample.After undergoing pre-strain and artificial aging(T6 state),the SRS samples have comparable yield strength to CS samples,satisfying the service requirements.This work provides technological support to industrially manufacture high performance AA6xxx series alloys with competitive advantage by a novel,short and low-cost process,and open a door for the further development of twin-roll casting based on SRS technique in industries.展开更多
In order to detecting and tracking along the weld seam with rotating arc sensor in underwater welding,the highpressure water environment rotating arc welding hardware platform is established and welding experiments us...In order to detecting and tracking along the weld seam with rotating arc sensor in underwater welding,the highpressure water environment rotating arc welding hardware platform is established and welding experiments using rotating arc sensor is done. Different radius of rotating arc sensor is used. And the corresponding welding current and voltage is obtained,which is compared with the results of rotating arc sensor short-circuit process simulation model under high-pressure water environment established in this article. The results show that under high-pressure water environment,rotating arc radius should be optimized,otherwise the short-circuit-arcing cycle will transit to a short-circuit-arcing-abruption cycle,making the welding quality poor. At last the critical radius between the short-circuit-arcing cycle and short-circuit-arcing-abruption cycle under high-pressure water environment is obtained.展开更多
The effects of Reactive Black 5 utilized to cotton fabrics by short wet-steam process on the dyeing properties were investigated. This study will provide a theoretical reference for short wet-steam process of cotton f...The effects of Reactive Black 5 utilized to cotton fabrics by short wet-steam process on the dyeing properties were investigated. This study will provide a theoretical reference for short wet-steam process of cotton fabrics with bifunctional reactive dyes. The optimal amount of Selilao agent was 20 g/L, while the soaping and rubbing fastness of the dyed cotton fabrics were both reached to 4-5 rating.展开更多
An intelligent fuzzy c-means system for process monitoring and recognition of process disturbances during short- circuiting gas metal arc welding （GMAW） is introduced in this paper. The raw measured and statisticall...An intelligent fuzzy c-means system for process monitoring and recognition of process disturbances during short- circuiting gas metal arc welding （GMAW） is introduced in this paper. The raw measured and statistically test data of probability density distribution （ PDD ） and class frequency distribution （ CFD ） of welding electrical parameters are further processed into a 7-dimensional array which is designed to describe various welding conditions, and is employed as input vector of the intelligent fuzzy c-means system. The fuzzy c-means system is used to conduct process monitoring and automatic recognition. The correct recognition rate of 24 test data under 8 kinds of welding condition is 92%.展开更多
The modeling of the term structure of interest rates is one of primary topics for researches in financial economics. Here we consider models of the short interest rate in discrete processes. Our methodology of analysi...The modeling of the term structure of interest rates is one of primary topics for researches in financial economics. Here we consider models of the short interest rate in discrete processes. Our methodology of analysis follows the framework of discrete stochastic calculus.展开更多
基金Financial supports from The National key research and development program(No.2016YFE0115300)The Natural Science Foundation of China(Nos.51790483,51625402,51790485 and 51801069)are greatly acknowledged+2 种基金Partial financial support came from The science and technology development program of Jilin Province(No.20190901010JC)The Changjiang Scholars Program(T2017035)the Program for JLU Science and Technology Innovative Research Team(JLUSTIRT,2017TD-09).
文摘Al-Mg-Si(AA6xxx)series alloys have been used widely in automotive industry for lightweight purpose.This work focuses on developing a short process for manufacturing Al-0.5Mg-1.3Si(wt.%)alloy sheets with good mechanical properties.Hereinto,a preparation route without homogenization was proposed on the basis of sub-rapid solidification(SRS)technique.The sample under SRS has fine microstructure and higher average partition coefficients of solute atoms,leading to weaker microsegregation owing to the higher cooling rate(160℃/s)than conventional solidification(CS,30℃/s).Besides,Mg atoms tend to be trapped in Al matrix under SRS,inducing suppression of Mg2Si,and promoting generation of Al Fe Si phase.After being solution heat treated(T4 state),samples following the SRS route have lower yield strength compared with that by CS route,indicating better formability in SRS sample.After undergoing pre-strain and artificial aging(T6 state),the SRS samples have comparable yield strength to CS samples,satisfying the service requirements.This work provides technological support to industrially manufacture high performance AA6xxx series alloys with competitive advantage by a novel,short and low-cost process,and open a door for the further development of twin-roll casting based on SRS technique in industries.
基金supported by the National Natural Science Foundation of China(Grant No.51665016)founded by the China Scholarship Council(Grant No.201508360113)
文摘In order to detecting and tracking along the weld seam with rotating arc sensor in underwater welding,the highpressure water environment rotating arc welding hardware platform is established and welding experiments using rotating arc sensor is done. Different radius of rotating arc sensor is used. And the corresponding welding current and voltage is obtained,which is compared with the results of rotating arc sensor short-circuit process simulation model under high-pressure water environment established in this article. The results show that under high-pressure water environment,rotating arc radius should be optimized,otherwise the short-circuit-arcing cycle will transit to a short-circuit-arcing-abruption cycle,making the welding quality poor. At last the critical radius between the short-circuit-arcing cycle and short-circuit-arcing-abruption cycle under high-pressure water environment is obtained.
文摘The effects of Reactive Black 5 utilized to cotton fabrics by short wet-steam process on the dyeing properties were investigated. This study will provide a theoretical reference for short wet-steam process of cotton fabrics with bifunctional reactive dyes. The optimal amount of Selilao agent was 20 g/L, while the soaping and rubbing fastness of the dyed cotton fabrics were both reached to 4-5 rating.
基金The authors are grateful to the financial support provided by the National Natural Science Foundation of China under grant No. 51005106, Research Fund for the Doctoral Program of Jiangsu Uni- versity of Science and Technology under grant No. 35060902, A Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions.
文摘An intelligent fuzzy c-means system for process monitoring and recognition of process disturbances during short- circuiting gas metal arc welding （GMAW） is introduced in this paper. The raw measured and statistically test data of probability density distribution （ PDD ） and class frequency distribution （ CFD ） of welding electrical parameters are further processed into a 7-dimensional array which is designed to describe various welding conditions, and is employed as input vector of the intelligent fuzzy c-means system. The fuzzy c-means system is used to conduct process monitoring and automatic recognition. The correct recognition rate of 24 test data under 8 kinds of welding condition is 92%.
文摘The modeling of the term structure of interest rates is one of primary topics for researches in financial economics. Here we consider models of the short interest rate in discrete processes. Our methodology of analysis follows the framework of discrete stochastic calculus.
