A spatiotemporal evolution model of a short-circuit arc to a secondary arc based on the improved charge simulation method

The initial shape of the secondary arc considerably influences its subsequent shape.To establish the model for the arcing time of the secondary arc and modify the single-phase reclosing sequence,theoretical and experimental analysis of the evolution process of the short-circuit arc to the secondary arc is critical.In this study,an improved charge simulation method was used to develop the internal-space electric-field model of the short-circuit arc.The intensity of the electric field was used as an independent variable to describe the initial shape of the secondary arc.A secondary arc evolution model was developed based on this model.Moreover,the accuracy of the model was evaluated by comparison with physical experimental results.When the secondary arc current increased,the arcing time and dispersion increased.There is an overall trend of increasing arc length with increasing arcing time.Nevertheless,there is a reduction in arc length during arc ignition due to short circuits between the arc columns.Furthermore,the arcing time decreased in the range of 0°-90°as the angle between the wind direction and the x-axis increased.This work investigated the method by which short-circuit arcs evolve into secondary arcs.The results can be used to develop the secondary arc evolution model and to provide both a technical and theoretical basis for secondary arc suppression.

The numerical simulation and inversion fitting of radon concentration distribution in homogeneous overburden above active fault zones

Based on the convection and diffusion mechanisms of radon migration, in this paper we deduce the two-dimensional differential equation for radon transportation in the overburden above active fault zones with an unlimited extension along the strike. Making use of the finite difference method, the radon concentration distribution in the overburden above active faults is calculated and modeled. The active fault zone parameters, such as the depth and the width of the fault zone, and the value of radon concentration, can be inverted from the measured radon concentration curve. These realize quantitative interpretation for radon concentration anomalies. The inversion results are in good agreement with the actual fault zone parameters.

Dominant pulse simulation of near fault ground motions

In this study, a new mathematical model is developed composed of two parts, including harmonic and polynomial expressions for simulating the dominant velocity pulse of near fault ground motions. Based on a proposed velocity function, the corresponding expressions for the ground acceleration and displacement time histories are also derived. The proposed model is then fitted using some selected pulse-like near fault ground motions in the Next Generation Attenuation （NGA） project library. The new model is not only simple in form but also simulates the long-period portion of actual velocity near fault records with a high level of precision. It is shown that the proposed model-based elastic response spectra are compatible with the near fault records in the neighborhood of the prevailing frequency of the pulse. The results indicate that the proposed model adequately simulates the components of the time histories. Finally, the energy of the proposed pulse was compared with the energy of the actual record to confirm the compatibility.

Numerical simulation analysis of covering rock strata as mining steep-inclined coal seam under fault movement

The fault is one important factor for the stability of overburden strata caused by steeply inclined coal seam. The stress and displacement change of overburden strata caused by steeply-inclined coal seam mining activity under faulting was simulated by FLAC2D finite differential program on the basis of Zhaogezhuang mining example belonging to Kailuan Mining Group. From the results, the stress and displacement clouding image after mining became complex because of the fault, that is, a kind of weak structural plane. The stress concentration region concentrated around the goaf, and also around the fault plane. As the mining depth increases, the stress and displacement within the fault zone change significantly. This movement and deformation characteristic of overburden strata can provide theoretical basis for the similar mining condition.

基于Simulation X的多轴转向系统功能安全仿真分析

基于ISO 26262《道路车辆功能安全》的标准要求,对特种车的多轴电液转向系统进行分析,以提高系统的安全性和可靠性。运用Simulation X软件建立详细的多轴特种车仿真模型,通过模拟故障模式注入进行仿真试验。对仿真结果和数据进行分析,评估得到故障的严重性、暴露度和可控性,从而确定相应的汽车安全完整性等级。基于故障注入仿真的汽车功能安全分析方法,在系统早期设计阶段可以作为评估架构安全性的重要手段。

Numerical Simulation of Coal Floor Fault Activation Influenced by Mining

By means of the numerical simulation software ANSYS, the activation regularity of coal floor faults caused by mining is simulated. The results indicate that the variation in horizontal, vertical and shear stresses, as well as the horizontal and vertical displacements in the upper and the lower fault blocks at the workface are almost identical. Influ- enced by mining of the floor rock, there are stress releasing and stress rising areas at the upper part and at the footwall of the fault. The distribution of stress is influenced by the fault so that the stress isolines are staggered by the fault face and the stress is focused on the rock seam around the two ends of the fault. But the influence in fault activation on the upper or the lower fault blocks of the workface is markedly different. When the workface is on the footwall of the fault, there is a horizontal tension stress area on the upper part of the fault; when the workface is on the upper part of the fault, it has a horizontal compressive stress area on the lower fault block. When the workface is at the lower fault block, the maximum vertical displacement is 5 times larger then when the workface is on the upper fault block, which greatly in- creases the chance of a fatal inrush of water from the coal floor.

Numerical simulation of fault activity owing to hydraulic fracturing

We built a three-dimensional model to simulate the disturbance of the stress field near the reverse fault in Zhaziao, Leyi Township owing to hydraulic fracturing. The pore pressure, and shear and normal stresses during fracturing are analyzed in detail. Input rock mechanics parameters are taken from laboratory test data of shale samples from the study area. The simulation results suggest that after 16 hours of fluid injection, the pore-pressure variation can activate the reverse fault, i.e., we observe reverse slip, and the shear stress and displacement on the fault plane increase with time. The biggest stress–strain change occurs after one hour of fluid injection and the yield point appears about 0.5 h after injection. To observe the stress evolution in each section, the normal displacement on the boundary is constrained and the fault plane is set as nonpermeable. Thus, the sliding is limited and the shear displacement is only in the scale of millimeters, and the calculated magnitude of the induced earthquakes is between Mw-3.5 and Mw-0.2. The simulation results suggest that fluid water injection results in inhomogeneous fracturing. The main ruptured areas are around the injection positions, whereas the extent of rupturing and cracks in other areas are relatively small. Nevertheless, nonnegligible fault activation is recorded. Sensitivity analysis of the key parameters suggests that the pore pressure is most sensitive to the maximum unbalanced force and the internal friction angle strongly affects the fault slip. Finally, the comparison between the effective normal stress and the maximum and minimum principal stresses on the fault plane explains the fault instability, i.e., the Mohr circle moves towards the left with decreasing radius reduces and intersects the critical slip envelope, and causes the fault to slip.

3D simulation of near-fault strong ground motion: comparison between surface rupture fault and buried fault

In this paper, near-fault strong ground motions caused by a surface rupture fault （SRF） and a buried fault （BF） are numerically simulated and compared by using a time-space-decoupled, explicit finite element method combined with a multi-transmitting formula （MTF） of an artificial boundary. Prior to the comparison, verification of the explicit element method and the MTF is conducted. The comparison results show that the final dislocation of the SRF is larger than the BF for the same stress drop on the fault plane. The maximum final dislocation occurs on the fault upper line for the SRF; however, for the BE the maximum final dislocation is located on the fault central part. Meanwhile, the PGA, PGV and PGD of long period ground motions （≤ 1 Hz） generated by the SRF are much higher than those of the BF in the near-fault region. The peak value of the velocity pulse generated by the SRF is also higher than the BE Furthermore, it is found that in a very narrow region along the fault trace, ground motions caused by the SRF are much higher than by the BF. These results may explain why SRFs almost always cause heavy damage in near-fault regions compared to buried faults.

Genetic Analysis of Structural Styles in the Makran Accretionary Wedge–Insight from Physical Simulations

The Makran accretionary wedge has the smallest subduction angle among any accretionary prism in the world. The factors controlling the spacing and morphological development of its deep thrust faults, as well as the formation mechanism of shallow normal faults, remain unclear. Meanwhile, the factors affecting the continuity of plane faults must be comprehensively discussed. Clarifying the development characteristics and deformation mechanisms of the Makran accretionary wedge is crucial to effectively guide the exploration of gas hydrate deposits in the area. This study aims to interpret seismic data to identify typical structures in the Makran accretionary wedge, including deep imbricate thrust faults, shallow and small normal faults, wedge-shaped piggyback basins, mud diapirs with fuzzy and disorderly characteristics of reflection, décollements with a northward tilt of 1° – 2°, and large seamounts. Physical simulation-based experiments are performed to comprehensively analyze the results of the plane, section, and slices of the wedge. Results reveal that the distances between and shapes of thrust faults in the deep parts of the Makran accretionary wedge are controlled by the bottom décollement. The uplift of the thrust fault-related folds and the upwelling of the mud diapirs primarily contribute to the formation of small normal faults in the shallow part of the area. The mud diapirs originate from plastic material at the bottom, while those that have developed in the area near the trench are larger. Seamounts and mud diapirs break the continuity of fault plane distribution.

Numerical simulation on fault water-inrush based on fluid-solid coupling theory

About 75% water-inrush accidents in China are caused by geological structure such as faults, therefore, it is necessary to investigate the water-inrush mechanism of faults to provide references for the mining activity above confined water. In this paper, based on the fluid-solid coupling theory, we built the stress-seepage coupling model for rock, then we combined with an example of water-inrush caused by fault, studied the water-inrush mechanism by using the numerical software COMSOL Mutiphysics, analyzed the change rule of shear stress, vertical stress, plastic area and water pressure for stope with a fault, and estimated the water-inrush risk at the different distances between working faces and the fault. The numerical simula- tion results indicate that： （1） the water-inrush risk will grow as the decrease of the distance between working face and the fault; （2） the failure mode of the rock in floor with fault is shear failure; （3） the rock between water-containing fault and working face failure is the reason for water-inrush.

Geomechanics model test and numerical simulation of 2G-NPR bolt support effect in an active fault tunnel

Active faults are a common adverse geological phenomenon that can occur during tunnel excavation and has a very negative impact on the construction and operation of the tunnel.In this paper,the grade IV rock surrounding the cross-fault tunnel with poor geological conditions has been chosen for the study.The support capacity of 2^(nd) Generation-Negative Poisson’s Ratio(2G-NPR)bolt in an active fault tunnel has been carried out on the basis of relevant results obtained from the geomechanical model test and numerical investigations of failure model for existing unsupported fault tunnel.The investigation shows that surrounding rock of the tunnel is prone to shear deformation and crack formation along the fault,as a result,the rock mass on the upper part of the fault slips as a whole.Furthermore,small-scale deformation and loss of blocks are observed around the tunnel;however,the 2G-NPR bolt support is found to be helpful in keeping the overall tunnel intact without any damage and instability.Due to the blocking effect of fault,the stress of the surrounding rock on the upper and lower parts of the fault is significantly different,and the stress at the left shoulder of the tunnel is greater than that at the right shoulder.The asymmetrical arrangement of 2G-NPR bolts can effectively control the asymmetric deformation and instability of the surrounding rock.The present numerical scheme is in good agreement with the model test results,and can reasonably reflect the stress and displacement characteristics of the surrounding rock of the tunnel.In comparison to unsupported and ordinary PR(Poisson’s Ratio)bolt support,2G-NPR bolt can effectively limit the fault slip and control the stability of the surrounding rock of the fault tunnel.The research findings may serve as a guideline for the use of 2G-NPR bolts in fault tunnel support engineering.

Quantification and assessment of fault uncertainty and risk using stochastic conditional simulations

The effect of geological uncertainty on the development and mining of underground coal deposits is a key issue for longwall mining, as the presence of faults generates substantial monetary losses. This paper develops a method for the conditional simulation of fault systems and uses the method to quantify and assess fault uncertainty. The method is based on the statistical modelling of fault attributes and the simulation of the locations of the centres of the fault traces. Fault locations are generated from the thinning of a Poisson process using a spatially correlated probability field. The proposed algorithm for simulating fault traces takes into account soft data such as geological interpretations and geomechanical data. The simulations generate realisations of fault populations that reproduce observed faults, honour the statistics of the fault attributes, and respect the constraints of soft data, providing the means to thereby model and assess the related fault uncertainty.

Numerical Simulation of Earthquake Nucleation Process and Seismic Precursors on Faults

To understand precursory phenomena before seismic fault sliP,this work focuses onearthquake nucleation process on a fault plane through numerical simulation.Rate and statedependent friction law with variable normal stress is employed in the analysis.The resultsshow that in the late stage of nucleation process:(1)The maximum slip velocity ismonotonically accelerating;(2)The slipping hot spot(where the slip rate is maximum)migrates spontaneously from a certain instant,and such migration is spatially continuous;(3)When the maximum velocity reaches a detectable order of magnitude(at least one orderof magnitude greater than the loading rate),the remaining time is 20 hours or longer,andthe temporal variation of slip velocity beyond this point may be used as a precursoryindicator;(4)The average slip velocity is related to the remaining time by a log-log linearrelation,which means that a similar relation between rate of microseismicity and remainingtime may also exist;(5)when normal stress variation is taken

Measuring the Qatar-Kazeron Fault Dip Using Random Finite Fault Simulation of September 27, 2010 Kazeron Earthquake and Analytical Signal Map of Satellite Magnetic Data

In this research the fault parameters causing the September 27, 2010 Kazeron Earthquake with a magnitude of MW = 5.8 (BHRC) were determined using the random finite fault method. The parameters were recorded by 27 accelerometer stations. Simulation of strong ground motion is very useful for areas about which little information and data are available. Considering the distribution of earthquake records and the existing relationships, for the fault plane causing the September 27, 2010 Kazeron Earthquake the length of the fault along the strike direction and the width of the fault along the dip direction were determined to be 10 km and 7 km, respectively. Moreover, 10 elements were assumed along the length and 7 were assumed along the width of the plane. Research results indicated that the epicenter of the earthquake had a geographic coordination of 29.88N - 51.77E, which complied with the results reported by the Institute of Geophysics Tehran University (IGTU). In addition, the strike and dip measured for the fault causing the Kazeron Earthquake were 27 and 50 degrees, respectively. Therefore, the causing fault was almost parallel to and coincident with the fault. There are magnetic discontinuities on the analytical signal map with a north-south strike followed by a northwest-southeast strike. The discontinuities are consistent with the trend of Kazeron fault but are several kilometers away from it. Therefore, they show the fault depth at a distance of 12 km from the fault surface.

Geological Characteristics and Numerical Simulation of Badong Fault in TGP Reservoir Area

The new county-seat town of Badong in the reservoir area of the Three Gorges Project is located on a huge arcuate slope with a convex bank toward north. The slope is cut by a fault, Badong fault, trending in east-west in its back part. It is concerned if the huge arcuate slope is related to mass rock creep, and what is the role of the Badong fault in the formation of the huge arc slope? The Badong fault was put into main consideration in this paper. The data from field investigation were reviewed. Three main features of the Badong fault were summarized: a bedding fault between the Jialingjiang formation (T\-1j) and Badong formation (T\-2b), breccias with compound component, and multiple stages of activity. It was proposed that most of the breccias were formed by fracture-filling. To understand the state of stress and behavior of deformation of the fault during the incision of the Yangtze River as well as the initiation and development of the slope, numerical simulation was conducted. Results indicate that there is a tensional stress zone in the upper part of the fault, and that activity of the fault is dominated by bedding sliding. Opening was also noted in the upper part of the fault in the late periods. The results are consistent with the field observation of the fault. The displacement in the slope is small, which makes us conclude that there is no certain relation between the formation of the arcuate slope and the Badong fault.

Fractal Features and Computer Simulation of Fan-Shaped Sedimentary Bodies in Faulted Basins

Ｆａｎ－ｓｈａｐｅｄｓｅｄｉｍｅｎｔａｒｙｂｏｄｉｅｓａｒｅｔｈｏｓｅｍａｉｎｌｙｃｏｍ－ｐｏｓｅｄｏｆｔｅｒｉｇｅｎｏｕｓｃｏａｒｓｅｄｅｐｏｓｉｔｓａｎｄｂｅｉｎｇｆａｎ－ｓｈａｐｅｄｉｎｍｏｒｐｈｏｌｏｇｙ，ｉｎｃｌｕｄｉｎｇａｌｕｖｉａｌｆａ...

Construction of Network Fault Simulation Platform and Event Samples Acquisition Techniques for Event Correlation

Event correlation is one key technique in network fault management. For the event sample acquisition problem in event correlation, a novel approach is proposed to collect the samples by constructing network simulation platform. The platform designed can set kinds of network faults according to user's demand and generate a lot of network fault events, which will benefit the research on efficient event correlation techniques.

Computer simulation of short-circuiting transfer welding under waveform control on inverter power source

A simulation model is introduced about the non-linearity process of short-circuiting transfer in CO2 arc welding for displaying the interaction between the inverter power source and welding arc under waveform control. In the simulation model, the feedback signals of current and voltage are taken respectively at the different phase in a short circuit periodic time and applied to the PWM （pulse width modulation） module in a model of inverter power source to control the output of power source. The simulation operation about the dynamic process of CO2 short-circuiting transfer welding is implemented on the founded simulation model with a peak arc current of 400 A and a peak voltage of 35 V, producing the dynamic arc waveforms which can embody the effect of inverter harmonic wave. The simulating waveforms are close to that of welding experiments.

Numerical simulation on the influences of Wenchuan earthquake on the surrounding faults

On 12 May 2008, the devastating Wenchuan earthquake struck the Longmenshan fault zone, which comprised the eastern margin of the Tibetan Plateau, and this fault zone was predominantly a convergent boundary with a right-lateral strike-slip component. After such a large-magnitude earthquake, it was crucial to analyze the influences of the earthquake on the surrounding faults and the potential seismic activity. In this paper, a complex viscoelastic model of western Sichuan and eastern Tibet regions was constructed including the topography. Based on the findings of co-seismic static slip distribution, we calculated the stress change caused by the Wenchuan earthquake with the post-seismic relaxation into consideration. Our preliminary results indicated that： （1） The tectonic stressing rate was relatively high in Kunlun mountain pass-Jiangcuo, Ganzi-Yushu, Xianshuihe and Zemuhe faults; while in the east Kunlun and Longriba was medium; also the value was less in the Minjiang, Longmenshan, Anninghe and Huya faults. As to the Longmenshan fault, the value was 0.28×10-3 MPa/a to 0.35×10-3 MPa/a, which is coincident with the previous long recurrence interval of Wenchuan earthquake; （2） The Wenchuan earthquake not only caused the Coulomb stress decrease in the source region, but also the stress increase in the two terminals, especially the northeastern segment, which is comparatively consistent with the aftershock distribution. Meanwhile, the high concentration areas of the static slip distribution were corresponding to the Coulomb stress reductions; （3） The Coulomb stress change caused by Wenchuan earthquake showed significant increase on five major faults, which were northwestern segment of Xianshuihe fault, eastern Kunlun fault, Longriba fault, Minjiang fault and Huya fault respectively; also the Coulomb stress on the fault plane of the Yushu earthquake was faintly increased; （4） We defined the recurrence interval as the time needed to accumulate the magnitude of the stress drop, and the recurrence interval of Wenchuan earthquake was estimated about 1 714 a to 2 143 a correspondingly.

Magnetic Force Simulation of Cables in Microgrid during Faults

In recent years, more and more electric utilities are using underground cables to distribute electric power rather than overhead transmission line. However, the cost of installation and maintenance of underground cables is very expensive. Thus, the proper design and damage prediction of cables are crucial. This paper is focused on the magnetic force waveforms simulation of cables under different types of faults using PSCAD and COMSOL. The results show that three-phase fault leads to the largest magnetic forces and the maximum magnitude of the forces in the x-direction is about 2.5 N. Also, the magnetic fields surrounding the cables are different depending on the arrangements of cables buried method. Although the magnitude is small, considering the long distance and long operating time of underground cables, the forces between cables can cause failures under some conditions. In the future, more types of faults such as high impedance fault and different protecting technologies can be studied.