100 Gb/s coherent chaotic optical communication over 800 km fiber transmission via advanced digital signal processing

Chaotic optical communication has shown large potential as a hardware encryption method in the physical layer.As an important figure of merit,the bit rate–distance product of chaotic optical communication has been continually improved to 30 Gb/s×340 km,but it is still far from the requirement for a deployed optical fiber communication system,which is beyond 100 Gb/s×1000 km.A chaotic carrier can be considered as an analog signal and suffers from fiber channel impairments,limiting the transmission distance of high-speed chaotic optical communications.To break the limit,we propose and experimentally demonstrate a pilot-based digital signal processing scheme for coherent chaotic optical communication combined with deep-learning-based chaotic synchronization.Both transmission impairment recovery and chaotic synchronization are realized in the digital domain.The frequency offset of the lasers is accurately estimated and compensated by determining the location of the pilot tone in the frequency domain,and the equalization and phase noise compensation are jointly performed by the least mean square algorithm through the time domain pilot symbols.Using the proposed method,100 Gb∕s chaotically encrypted quadrature phase-shift keying(QPSK)signal over 800 km single-mode fiber(SMF)transmission is experimentally demonstrated.In order to enhance security,40 Gb∕s real-time chaotically encrypted QPSK signal over 800 km SMF transmission is realized by inserting pilot symbols and tone in a field-programmable gate array.This method provides a feasible approach to promote the practical application of chaotic optical communications and guarantees the high security of chaotic encryption.

Underground vibration signal detection and processing system based on LabWindows/CVI

In order to detect and process underground vibration signal, this paper presents a system with the combination of software and hardware. The hardware part consists of sensor, memory chips, USB, etc. , which is responsible for capturing original signals from sensors. The software part is a virtual oscilloscope based on LabWindows/CVI （C vitual instrument）, which not only has the functions of traditional oscilloscope but also can analyze and process vibration signals in special ways. The experimental results show that the designed system is stable, reliable and easy to be operated, which can meet practical requirements.

Kravchenko atomic transforms in digital signal processing

The modified atomic transformations are constructed and proved. On their basis the new complex analytic wavelets are obtained. The proof of the Fourier transforms existence in L~ and L2 on the basis of the theory of atomic functions （AF） are presented. The numerical experiments of digital time series processing and physical analysis of the results confirm the efficiency of the proposed transforms.

New WA-system of kravchenko functions in digital signal processing

On the basis of modified atomic transformations the new WA-systems of Kravchenko functions are constructed.As an example the digital processing of time series of the various physical nature processing is considered.The numerical experiments and physical analysis of the results confirm the efficiency of the proposed WA-systems of Kravchenko functions.

A beam position measurement system of fully digital signal processing at SSRF

This fully digital beam position measurement instrument is designed for beam position monitoring and machine research in Shanghai Synchrotron Radiation Facility. The signals received from four position-sensitive detectors are narrow pulses with a repetition rate up to 499.654 MHz and a pulse width of around 100 ps, and their dynamic range could vary over more than 40 dB in machine research. By the employment of the under-sampling technique based on high-speed high-resolution A/D conversion, all the processing procedure is performed fully by the digital signal processing algorithms integrated in one single Field Programmable Gate Array. This system functions well in the laboratory and commissioning tests, demonstrating a position resolution (at the turn by turn rate of 694 kHz) better than 7 μm over the input amplitude range of -40 dBm to 10 dBm which is well beyond the requirement.

Description and reconstruction of one-dimensional photonic crystal by digital signal processing theory

A method of describing one-dimensional photonic crystals （1DPCs） based on Z-domain digital signal processing theory is presented. The analytical expression of the target band gap spectrum in the digital domain is obtained by the autocorrelation of its impulse response. The feasibility of this method is verified by reconstructing two simple 1DPC structures with a target photonic band gap obtained by the traditional transfer matrix method. This method provides an effective approach to function-guided designs of interference-based band gap structures for photonic applications.

Real-Time Discrete Adaptive Control of Robot Arm Based on Digital Signal Processing

A discrete model reference adaptive controller of robot arm is obtained by integrating the reduced dynamic model of robot, model reference adaptive control （MRAC） and digital signal processing （DSP） computer system into an electromechanical system. With the DSP computer system, the control signal of each joint of the robot arm can be processed in real time and independently. The simulation and experiment results show that with the control strategy, the robot achieved a good trajectory following precision, a good decoupling performance and a high real-time adaptivity.

Design and Construction of a Digital Multichannel Analyzer for HPGe Detector Using Digital Signal Processing Technique

The outstanding advantage of digital signal processing (DSP) techniques and Field Programmable Gate Array (FPGA) technology is capable of improving the quality of the experimental measurements for nuclear radiation. In this article, a compact DMCA 8 K was designed and manufactured using DSP technique based on FPGA technology. In particular, the output of the preamplifier is completely processed by digital techniques which are obtained from the analog-to-digital converter (ADC) to calculate the baseline, DC offset, energy peaks, pile up, threshold discrimination and then the form of energy spectrum. The Spartan-6 board is used as a hardware for the development of the digital multichannel analyzer (DMCA), which is equipped with the 14-bit AD6645 with 62.5 Msps sample rate. The application software for instrument control, data acquisition and data processing was written under C++ builder via the RS-232 interface. The designed DMCA system has been tested with a HPGe detector using gamma sources of 60Co and 137Cs and a reference pulser.

Adaptive and Intelligent Digital Signal Processing for Improved Optical Interconnection

In recent years, explosively increasing data traffic has been boosting the con?tinuous demand of high speed optical interconnection inside or among data centers, high performance computers and even consumer electronics. To pursue the improved intercon?nection performance of capacity, energy efficiency and simplicity, effective approaches are demonstrated including particularly advanced digital signal processing (DSP) meth?ods. In this paper, we present a review about the enabling adaptive DSP methods for opti?cal interconnection applications, and a detailed summary of our recent and ongoing works in this field. In brief, our works focus on dealing with the specific issues for short-reach interconnection scenarios with adaptive operation, including signal-to-noise-ratio (SNR) limitation, level nonlinearity distortion, energy efficiency consideration and the de?cision precision.

Virtual Experimental Project Design in the Digital Signal Processing Course

This paper proposes the design and development of virtual experimental projects in the Digital Signal Processing course,using MATLAB,Proteus,and CCS platforms to develop a library of typical experimental cases for biomedical engineering majors and discusses the design process.Based on these typical cases,this paper explores the secondary design for innovative engineering practice case teaching,which can promote students’understanding and mastery of digital signal processing theories,algorithms,and technologies in an intuitive,flexible,and efficient way;quickly build new innovative engineering case models and further cultivate students’engineering application ability as well as innovative thinking.

Wideband Signal Detection Based on MWC Discrete Compressed Sampling Structure

In order to solve the cross-channel signal problem caused by the uniform channelized wideband digital receiver when processing wideband signal and the problem that the sensitivity of the system greatly decreases when the bandwidth of wideband digital receiver increases,which both decrease the wideband radar signal detection performance,a new wideband digital receiver based on the modulated wideband converter(MWC)discrete compressed sampling structure and an energy detection method based on the new receiver are proposed.Firstly,the proposed receiver utilizes periodic pseudo-random sequences to mix wideband signals with baseband and other sub-bands.Then the mixed signals are low-pass filtered and downsampled to obtain the baseband compressed sampling data,which can increase the sensitivity of the system.Meanwhile,the cross-channel signal will all appear in any subbands,so the cross-channel signal problem can be solved easily by processing the baseband compressed sampling data.Secondly,we establish the signal detection model and formulate the criterion of the energy detection method.And we directly utilize the baseband compressed sampling data to carry out signal detection without signal reconstruction,which decreases the complexity of the algorithm and reduces the computational burden.Finally,simulation experiments demonstrate the effectiveness of the proposed receiver and show that the proposed signal detection method is effective in low signal-to-noise ratio(SNR)compared with the conventional energy detection and the probability of detection increases significantly when SNR increases.

Data Analysis Methods and Signal Processing Techniques in Gravitational Wave Detection

Gravitational wave detection is one of the most cutting-edge research areas in modern physics, with its success relying on advanced data analysis and signal processing techniques. This study provides a comprehensive review of data analysis methods and signal processing techniques in gravitational wave detection. The research begins by introducing the characteristics of gravitational wave signals and the challenges faced in their detection, such as extremely low signal-to-noise ratios and complex noise backgrounds. It then systematically analyzes the application of time-frequency analysis methods in extracting transient gravitational wave signals, including wavelet transforms and Hilbert-Huang transforms. The study focuses on discussing the crucial role of matched filtering techniques in improving signal detection sensitivity and explores strategies for template bank optimization. Additionally, the research evaluates the potential of machine learning algorithms, especially deep learning networks, in rapidly identifying and classifying gravitational wave events. The study also analyzes the application of Bayesian inference methods in parameter estimation and model selection, as well as their advantages in handling uncertainties. However, the research also points out the challenges faced by current technologies, such as dealing with non-Gaussian noise and improving computational efficiency. To address these issues, the study proposes a hybrid analysis framework combining physical models and data-driven methods. Finally, the research looks ahead to the potential applications of quantum computing in future gravitational wave data analysis. This study provides a comprehensive theoretical foundation for the optimization and innovation of gravitational wave data analysis methods, contributing to the advancement of gravitational wave astronomy.

Digital Signal Processing Based Real Time Vehicular Detection System

Traffic monitoring is of major importance for enforcing traffic management policies.To accomplish this task,the detection of vehicle can be achieved by exploiting image analysis techniques.In this paper,a solution is presented to obtain various traffic parameters through vehicular video detection system(VVDS).VVDS exploits the algorithm based on virtual loops to detect moving vehicle in real time.This algorithm uses the background differencing method,and vehicles can be detected through luminance difference of pixels between background image and current image.Furthermore a novel technology named as spatio-temporal image sequences analysis is applied to background differencing to improve detection accuracy.Then a hardware implementation of a digital signal processing (DSP) based board is described in detail and the board can simultaneously process four-channel video from different cameras. The benefit of usage of DSP is that images of a roadway can be processed at frame rate due to DSP′s high performance.In the end,VVDS is tested on real-world scenes and experiment results show that the system is both fast and robust to the surveillance of transportation.

Holographic storage scheme based on digital signal processing

In this paper, a holographic storage scheme for multimedia data storage and retrieval based on the digital signal processing (DSP) is designed. A communication model for holographic storage system is obtained on the analogy of traditional communication system. Many characteristics of holographic storage are embodied in the communication model. Then some new methods of DSP including two-dimensional (2-D) shifting interleaving, encoding and decoding of modulation-array (MA) code and method of soft-decision, etc. are proposed and employed in the system. From the results of experiments it can be seen that those measures can effectively reduce the influence of noise. A segment of multimedia data, including video and audio data, is retrieved successfully after holographic storage by using those techniques.

Signal and Data Processing of Television Based on Multistatic Radar Systems

A television based multistatic radar system is described. The commercial television transmitter is used as the illuminator in the multistatic radar system. The reflected commercial television signals are measured by an array of sensors. A data processing scheme is developed that adapts to the poor signal processing ability. The innovation is focused on the construction of the observation space, which could reduce the non linearity error. The new method leads to better system stability than the traditional one. Monte Carlo simulation is utilized and compared with the traditional method.

Delivery of 40 Gbit/s W-band signal over 4600 m wireless distance employing advanced digital signal processing

We experimentally built a photonics-aided long-distance large-capacity millimeter-wave wireless transmission system and demonstrated a delivery of 40 Gbit/s W-band 16-ary quadrature amplitude modulation(QAM)signal over 4600 m wireless distance at 88.5 GHz.Advanced offline digital signal processing algorithms are proposed and employed for signal recovery,which makes the bit-error ratio under 2.4×10^(−2).To the best of our knowledge,this is the first field-trial demonstration of>4 km W-band 16QAM signal transmission,and the result achieves a record-breaking product of wireless transmission capacity and distance,i.e.,184(Gbit/s)·km,for high-speed and long-distance W-band wireless communication.

Measuring Absolute Delay of RNSS Signal Channel Using Digital Envelope Detection

The absolute delay caused by equipment of radio navigation satellite service (RNSS) signal channel must be calibrated in the application of positioning. The measurement accuracy of absolute delay will affect the positioning precision of RNSS user. An absolute delay measurement technique using digital envelope detection was developed for RNSS signal transmission channel. The RNSS transmission signal of navigation satellite and the one pulse per second (1PPS)generated by satellite time keeping system were sampled synchronously. With sampling data of 1PPS,the reference point of the absolute delay can be decided at first,and then sampling data of RNSS transmission signal were truncated. The truncated data were processed using digital envelop detection algorithm to search the phase converting points of RNSS signal. Finally,the absolute delay of RNSS signal transmitting channel was calculated. Uncertainty of measurement with proposed technique is lower than 0. 2 ns as the sampling frequency is 10 GHz.

An acquisition system of digital nuclear signal processing for the algorithm development

A principle and method of constructing the digital acquisition system is presented in this work,which is convenient for the study on the theories and algorithms of digital nuclear signal processing.The hardware system of the digital acquisition system consists of front-end controller,waveform digitizer and PC workstation,on which the software system has been developed based on Visual C++under Windows environment.The alterable-frequency sampling(AFS)algorithm and the alterable-frequency trapezoidal filter(AFTF)algorithm have also been studied in the real-time environment,along with a digital nuclear spectrum acquisition system being set up based on the new algorithms and theγ-ray spectra of 241Am being shown.A useful experimental platform could be provided by this work for the successive work such as the development of global digitized nuclear measurement system and the study of digital nuclear signal processing.

A Sensor Failure Detection Method Based on Artificial Neural Network and Signal Processing

This paper proposes a sensor failure detection method based on artificial neural network and signal processing,in comparison with other methods,which does not need any redundancy information among sensor outputs and divides the output of a sensor into'Signal dominant component'and'Noise dominant component'because the pattern of sensor failure often appears in the'Noise dominant component'.With an ARMA model built for'Noise dominant component'using artificial neural network,such sensor failures as bias failure,hard failure,drift failure,spike failure and cyclic failure may be detected through residual analysis,and the type of sensor failure can be indicated by an appropriate indicator.The failure detection procedure for a temperature sensor in a hovercraft engine is simulated to prove the applicability of the method proposed in this paper.

DIGITAL PROCESSING OF THE POLARIZATION STATE OF GEOPHYSICAL ULF SIGNALS

In this paper, the evaluation by running window smoothing is used for the digital processing of the polarization of geophysical ULF signals. The observed signals are resolved into two orthogonal complex components so that it is no longer necessary to consider the phase and amplitude of the signals simultaneously.