New Wavelet Thresholding Algorithm in Dropping Ambient Noise from Underwater Acoustic Signals

Underwater Wireless Communication, largely dependent on the acoustic communication between the machines, is largely affected by various types of noise in the shallow and deep water. However ambient noise which is due to multiple sources (e.g. shipping, wind) and no one source dominates. Ambient noise masks the acoustic signal to a large extent. Hence today it has drawn the attention of the experts to reduce its effect on the received signal. This paper discusses ambient noise problem and devises a new wavelet thresholding method to reduce its effect. Afterwards a comparative study on statistical parameters is shown to prove the efficiency of the devised method.

Signal-to-noise ratio comparison of angular signal radiography and phase stepping method

Grating-based x-ray phase contrast imaging has the potential to be applied in future medical applications as it is compatible with both laboratory and synchrotron source. However, information retrieval methods are important because acquisition speed, scanning mode, image quality, and radiation dose depend on them. Phase-stepping （PS） is a widely used method to retrieve information, while angular signal radiography （ASR） is a newly established method. In this manuscript, signal-to-noise ratios （SNRs） of ASR are compared with that of PS. Numerical experiments are performed to validate theoretical results. SNRs comparison shows that for refraction and scattering images ASR has higher SNR than PS method, while for absorption image both methods have same SNR. Therefore, our conclusions would have guideline in future preclinical and clinical applications.

SUBSPACE-BASED NOISE VARIANCE AND SNR ESTIMATION FOR MIMO OFDM SYSTEMS

This paper proposes a subspace-based noise variance and Signal-to-Noise Ratio (SNR) estimation algorithm for Multi-Input Multi-Output (MIMO) wireless Orthogonal Frequency Division Multiplexing (OFDM) systems. The special training sequences with the property of orthogonality and phase shift orthogonality are used in pilot tones to obtain the estimated channel correlation matrix. Partitioning the observation space into a delay subspace and a noise subspace, we achieve the measurement of noise variance and SNR. Simulation results show that the proposed estimator can obtain accurate and real-time measurements of the noise variance and SNR for various multipath fading channels, demonstrating its strong robustness against different channels.

THE METHOD OF SEPARATING HARMONIC SIGNALS FROM MULTIPLICATIVE AND ADDITIVE NOISES

This paper focuses on the extraction of a harmonic signal from multiplicative and additive noises. A method is proposed in two stages: (1) to square the original discrete time series, which in- cludes both signals and noises, and form a new time series. By this means, the multiplicative noise is converted to additive noise; and (2) to filter out the noise by using existing noise removal schemes. With a large amount of simulation, experimental results demonstrated the efficiency and effective- ness of this newly developed method in terms of Signal-to-Noise Ratio (SNR) and other criteria. From the experiment, it is also found that: the two kinds of noises affect the SNR differently. In gen- eral, the SNR is not influenced by multiplicative Gaussian noise regardless of its variance. However, if both kinds of noise exist, the SNR decreases with the incensement of the Variance of Additive Noise to Multiplicative Noise Ratio (VAMNR). This analysis is also supported by simulation work.

Applying sub-band energy extraction to noise cancellation of ultrasonic NDT signal

In ultrasonic non-destructive tests, the echo signal at the flaw is highly complex due to the interference of multiple echoes with random amplitudes and phases, and is disturbed by all kinds of noises, such as thermal noise, digitalization noise, and structure noise. In this paper, the ultrasonic signal was decomposed by empirical mode decomposition (EMD) to obtain the in-trinsic mode function (IMF) components according to ultrasonic defect echo signals occuring at the corresponding time, and the energy of the ultrasonic signal was concentrated. The IMF component selection criterion based on sub-band energy extraction was proposed to extract the ultrasonic signal component accurately and automatically from IMF components. When the selected IMF components were filtered by a band pass filter, the signal-to-noise ratio (SNR) was enhanced greatly.

A BLIND SNR ESTIMATOR FOR DIGITAL BANDPASS SIGNALS

A subspace-based blind Signal-to-Noise Ratio (SNR) estimation algorithm for digital bandpass signals in Additive White Gaussian Noise (AWGN) channel is discussed. The lower bounds of the mean and variance of the estimation are derived, and simulations are performed for the commonly used digital bandpass signals, such as MPSK (M=2, 4, 8), MFSK (M=2, 4) and MQAM (M=16, 64, 128, 256) signals. Theoretical analyses and simulation results indicate that the proposed algorithm is ef- fective even when the SNR is below 0dB. Furthermore, the algorithm can provide a blind estimator in that it needs neither the parameters of the received signals, such as the carrier frequency, symbol rate and modulation scheme, nor the synchronization of the system.

Long term integration of radar signals with unknown Doppler shift for ubiquitous radar

Ubiquitous radar is a new radar system that provides continuous and uninterrupted multifunction capability within a coverage volume. Continuous coverage from close-in ＂pop-up＂ targets in clutter to long-range targets impacts selection of waveform parameters. The coherent processing interval （CPI） must be long enough to achieve a certain signal-to-noise ratio （SNR） that ensures the efficiency of detection. The condition of detection in the case of low SNR is analyzed, and three different cases that would occur during integration are discussed and a method to determine the CPI is presented. The simulation results show that targets detection with SNR as low as -26 dB in the experimental system can possibly determine the CPI.

A NOVEL METHOD FOR ESTIMATING THE SNR OF UNKNOWN EMITTER SIGNAL

It is important to estimate the Signal-to-Noise Ratio(SNR) of unknown emitter signal accurately.In order to resolve the disadvantages of present algorithm,a novel method is proposed in this letter.We extract and normalize the information of zero frequency of received signal by the Wigner-Vile Distribution(WVD) transformation and then get the approximate power of original signal by mathematic transformation,at last,we get the estimate value of SNR by the known account formula of SNR.Simulation results show that it is correct and feasible.

Rolling element bearing instantaneous rotational frequency estimation based on EMD soft-thresholding denoising and instantaneous fault characteristic frequency

The accurate estimation of the rolling element bearing instantaneous rotational frequency(IRF) is the key capability of the order tracking method based on time-frequency analysis. The rolling element bearing IRF can be accurately estimated according to the instantaneous fault characteristic frequency(IFCF). However, in an environment with a low signal-to-noise ratio(SNR), e.g., an incipient fault or function at a low speed, the signal contains strong background noise that seriously affects the effectiveness of the aforementioned method. An algorithm of signal preprocessing based on empirical mode decomposition(EMD) and wavelet shrinkage was proposed in this work. Compared with EMD denoising by the cross-correlation coefficient and kurtosis(CCK) criterion, the method of EMD soft-thresholding(ST) denoising can ensure the integrity of the signal, improve the SNR, and highlight fault features. The effectiveness of the algorithm for rolling element bearing IRF estimation by EMD ST denoising and the IFCF was validated by both simulated and experimental bearing vibration signals at a low SNR.

Nonsaturation Throughput Enhancement of IEEE 802.11b Distributed Coordination Function for Heterogeneous Traffic under Noisy Environment

In this paper, we propose a mechanism named modified backoff （MB） mechanism to decrease the channel idle time in IEEE 802.11 distributed coordination function （DCF）. In the noisy channel, when signal-to-noise ratio （SNR） is low, applying this mechanism in DCF greatly improves the throughput and lowers the channel idle time. This paper presents an analytical model for the performance study of IEEE 802.11 MB-DCF for nonsaturated heterogeneous traffic in the presence of transmission errors. First, we introduce the MB-DCF and compare its performance to IEEE 802.11 DCF with binary exponential backoff （BEB）. The IEEE 802.11 DCF with BEB mechanism suffers from more channel idle time under low SNR. The MB-DCF ensures high throughput and low packet delay by reducing the channel idle time under the low traffic in the network. However, to the best of the authors＇ knowledge, there are no previous works that enhance the performance of the DCF under imperfect wireless channel. We show through analysis that the proposed mechanism greatly outperforms the original IEEE 802.11 DCF in the imperfect channel condition. The effectiveness of physical and link layer parameters on throughput performance is explored. We also present a throughput investigation of the heterogeneous traffic for different radio conditions.

An Improved Image Denoising Method Based on Wavelet Thresholding

VisuShrink, ModineighShrink and NeighShrink are efficient image denoising algorithms based on the discrete wavelet transform (DWT). These methods have disadvantage of using a suboptimal universal threshold and identical neighbouring window size in all wavelet subbands. In this paper, an improved method is proposed, that determines a threshold as well as neighbouring window size for every subband using its lengths. Our experimental results illustrate that the proposed approach is better than the existing ones, i.e., NeighShrink, ModineighShrink and VisuShrink in terms of peak signal-to-noise ratio (PSNR) i.e. visual quality of the image.

A New Image Denoising Scheme Using Soft-Thresholding

The VisuShrink is one of the important image denoising methods. It however does not provide good quality of image due to removing too many coefficients especially using soft-thresholding technique. This paper proposes a new image denoising scheme using wavelet transformation. In this paper, we modify the coefficients using soft-thresholding method to enhance the visual quality of noisy image. The experimental results show that our proposed scheme has better performance than the VisuShrink in terms of peak signal-to-noise ratio (PSNR) i.e., visual quality of the image.

Denoising of an Image Using Discrete Stationary Wavelet Transform and Various Thresholding Techniques

Image denoising has remained a fundamental problem in the field of image processing. With Wavelet transforms, various algorithms for denoising in wavelet domain were introduced. Wavelets gave a superior performance in image denoising due to its properties such as multi-resolution. The problem of estimating an image that is corrupted by Additive White Gaussian Noise has been of interest for practical and theoretical reasons. Non-linear methods especially those based on wavelets have become popular due to its advantages over linear methods. Here I applied non-linear thresholding techniques in wavelet domain such as hard and soft thresholding, wavelet shrinkages such as Visu-shrink (non-adaptive) and SURE, Bayes and Normal Shrink (adaptive), using Discrete Stationary Wavelet Transform (DSWT) for different wavelets, at different levels, to denoise an image and determine the best one out of them. Performance of denoising algorithm is measured using quantitative performance measures such as Signal-to-Noise Ratio (SNR) and Mean Square Error (MSE) for various thresholding techniques.

Implementation of GPR Signals De-Noising Based on DSP

An important issue of ground-penetrating radar （GPR） signals analysis is de-noising thai is the guarantee of acquiring good detecting effect. The paper illustrates a successful application of digital single processor （DSP） based on wavelet shrinkage algorithm. In order to realize real-time GPP, signals analysis, some key issues are discussed such as the realization of fast wavelet transformation, the selection of CPU chip and the optimization of data movement. Experimenial results show that the DSP based application not only basically meets the real-time requirement of GPP, signals analysis, but also assures the quality of the GPR signals analysis.

Network Sorting Algorithm of Multi-Frequency Signal with Adaptive SNR

An signal noise ratio（ SNR） adaptive sorting algorithm using the time-frequency（ TF）sparsity of frequency-hopping（ FH） signal is proposed in this paper. Firstly,the Gabor transformation is used as TF transformation in the system and a sorting model is established under undetermined condition; then the SNR adaptive pivot threshold setting method is used to find the TF single source. The mixed matrix is estimated according to the TF matrix of single source. Lastly,signal sorting is realized through improved subspace projection combined with relative power deviation of source. Theoretical analysis and simulation results showthat this algorithm has good effectiveness and performance.

Denoising of Medical Images Using Multiwavelet Transforms and Various Thresholding Techniques

The problem of estimating an image corrupted by additive white Gaussian noise has been of interest for practical reasons. Non-linear denoising methods based on wavelets, have become popular but Multiwavelets outperform wavelets in image denoising. Multiwavelets are wavelets with several scaling and wavelet functions, offer simultaneously Orthogonality, Symmetry, Short support and Vanishing moments, which is not possible with ordinary (scalar) wavelets. These properties make Multiwavelets promising for image processing applications, such as image denoising. The aim of this paper is to apply various non-linear thresholding techniques such as hard, soft, universal, modified universal, fixed and multivariate thresholding in Multiwavelet transform domain such as Discrete Multiwavelet Transform, Symmetric Asymmetric (SA4), Chui Lian (CL), and Bi-Hermite (Bih52S) for different Multiwavelets at different levels, to denoise an image and determine the best one out of it. The performance of denoising algorithms and various thresholding are measured using quantitative performance measures such as, Mean Square Error (MSE), and Root Mean Square Error (RMSE), Signal-to-Noise Ratio (SNR), Peak Signal-to-Noise Ratio (PSNR). It is found that CL Multiwavelet transform in combination with modified universal thresholding has given best results.

GEO卫星机会源近岸海面高度测量性能评估

基于同步地球轨道(Geostationary Earth Orbit,GEO)卫星的机会源技术已被证明其在近岸海面高度测量中的应用潜力,但目前研究主要围绕可行性论证展开,极少开展全方位的测量性能评估.为此,从仿真和试验两个角度评估了信号带宽、非相干累加次数、信噪比及波形峰值跟踪算法对GEO卫星机会源海面测高性能的影响.评估结果表明当非相干累加次数和信噪比大于最优非相干累加次数和最优信噪比时,测高性能将不再显著提升.因此,通过选择最优非相干累加次数,以及设计合理的接收天线增益、射频增益及接收机带宽使信噪比大于最优信噪比对GEO卫星机会源海面测高至关重要.通过对比插值和拟合两种波形跟踪算法发现拟合法能提供比插值法更高的测量精度.利用北斗B3I信号和ASTRA 19.2 E卫星信号开展GEO卫星海面测高的试验评估.试验结果表明:在非相干累加次数大于10000、信噪比大于7 dB时,北斗B3I信号和ASTRA 19.2 E卫星信号可分别提供精度约为0.20 m和0.10 m的海面高度.针对GEO卫星多频或多通道传输特点,提出了基于信号频谱合成提高海面测高精度的方法.当利用中卫1号卫星10个通道信号进行合成时,插值法和拟合法的仿真测距精度分别为3.50 cm和0.69 cm.

基于逆全极点滤波器的高频PWM噪声整形方法

高频开关功率放大器具有高功率、低纹波、高响应的优点,是高加速、高精度定位系统的核心部件。为了解决高频PWM中开关频率与占空比分辨率的矛盾,该文分析调制中噪声整形的基本原理,采用误差反馈结构提取PWM量化噪声进行数字整形,阐述噪声整形滤波器设计约束条件。提出通过逆全极点无限脉冲响应(IIR)滤波器获得有限脉冲响应(FIR)噪声整形滤波器的简明设计方法,仿真及实验表明,该文提出的方法可利用低阶FIR整形滤波器获得平坦的通带和高整形衰减。在不足9位的PWM中,4阶的FIR噪声整形滤波器能够恢复调制信号在10 kHz频段内约40 dB的信噪比损失。

基于自适应估计SNR的分组Turbo码译码算法

针对分组Turbo码自适应Chase译码算法中SNR是预先设定值的情况,提出一种新的自适应估计信噪比(SNR)的译码算法。该方案利用了接收码字的统计信息与SNR之间存在的对应关系来调整门限函数,达到控制译码复杂度的目的。仿真结果表明,所提出的译码算法能自适应反映信道情况,降低译码运算复杂度,提高译码处理速度,获得了较好的性能。

基于FRFT的低信噪比LFM信号参数快速估计算法

基于分数阶傅里叶变换(Fractional Fourier Transform,FRFT)对线性调频(Linear Frequency Modulated,LFM)信号参数进行估计,问题关键是确定FRFT最佳阶数,根据误差迭代思想提出新的参数估计算法,该算法利用归一化带宽和旋转角的转化关系,由估计误差推算角度差值,有效降低了运算量,不需要调频斜率正负的先验信息,改进的对数搜索算法可以进一步提高参数估计结果的稳定性和可靠性。仿真结果表明,信噪比在-8 dB以上时该方法在高效率的前提下仍具有良好的参数估计性能,平均估计误差在1%以内,估计结果接近Cramer-Rao下限,满足工程实时处理需求。