Size Effect on the Radiation Stability Silicon Dioxide Sphere Particles

The effect of protons(E = 100 keV,F = 5×10^(15) cm^(-2)) exposure on the diffuse reflectance spectra of the SiO_(2 )with different size particles in wavelength range from 250 to 2500 nm have been investigated.Particles were nanosphere,submicrosphere,microsphere and submacrosphere,as well as solid micro-and nanocrystals.The synthesis of the particles was carried out by the formation of silica shells and dissolution of the polystyrene core particles.The surface morphology,surface area and crystal structure of the particles have been investigated.When evaluating the changes of the solar absorptance,it was found that the radiation stability of the micro-and submacro-hollow particles is higher than that of the other nanostructured particles,except for solid microcrystals.The low radiation stability of the hollow microparticles is due to the large void inside the hollow particles where radiation defects are not formed.

Preparation and photocatalytic activity of neodymium doping titania loaded to silicon dioxide

Neodymium doping titania was loaded to silicon dioxide to prepare Nd/TiO2-SiO2 by sol-gel method and Nd/TiO2-SiO2 was characterized by X-ray diffractometry （XRD）, scanning electron microscopy （SEM）, Fourier transform-infrared spectroscopy （FT-IR） and diffuse reflectance spectra （DRS）. Photocatalytic activities of Nd/TiO2-SiO2 with different neodymium contents were evaluated by degradation of methyl orange. The light absorption of Nd/TiO2-SiO2 increased with increasing doping neodymium in a visible light range of 388-619 nm, and Nd doping was in favor of decreasing the recombination of photo-generated electrons with holes. Nd and SiO2 improved the photocatalytic activity of TiO2. The optimal molar fraction of Nd to Ti was 0.1%, and the optimum calcination temperature was 600 ℃. The highest degradation rate of methyl orange was 82.9% after irradiation for 1 h.

Effect of TMS(nanostructured silicon dioxide) on growth of Changbai larch seedlings

The roots of 200 one-year-old Changbai Larch (Larix olgensis) seedlings were soaked for 6 hours at the TMS concentrations of 2000, 1000, 500, 250, 125, and 62 μL·L?1. Mean seedling height, root collar diameter, main root length and number of lateral roots were measured every 15 days during growing season from May 30 to Oct. 20. Experimental results showed that TMS treatments greatly promoted seedling growth and improved seedling quality. The treatment by 500 μL·L?1 TMS produced the best result, for which the mean height, root collar diameter, main root length, and the number of lateral roots of seedlings were increased by 42.5%, 30.7%, 14.0%, and 31.6%, respectively, compared to that of the control seedlings. As to seedling quality, grade-I seedling and grade-II seedlings were fifty-fifty, and no grade-III seedlings was found. The treatment by 500 μL·L?1 TMS resulted in the highest chlorophyll concentration. Keywords Changbai Larch - Larix olgensis - Seedling production - Nanostructured silicon dioxide CLC number S143.8 Document code B Foundation item: This study is supported by Jilin Forestry Group Co.Biography: LIN Baoshan (1955-), male, Associate professor at the college of forestry, Beihua University, Jilin City 132011, Jilin Province, P.R China.Responsible editor: Chai Ruihai.

Polymer grafting modification of the surface of nano silicon dioxide

Based on the composite modification technology of the surface of nano Silicondioxide by non-soap emulsion polymerization, it is verified that there are polymer grafted on thesurface of nano silicon dioxide. The modification mechanism and the bonding status on the surface ofnano silicon dioxide after modification were suggested via the results of the infrared spectrum,transmission electronic microscope photograph and X-ray photoelectron spectrum. The hydroxyl formedby hydrolyzing of silane coupling agent reacts with hydroxyl on the surface of nano silicon dioxideto form Si-O-Si bonds by losing water molecules and hence the double bonds are introduced onto thesurface of nano silicon dioxide. The surface of nano silicon dioxide is grafted with polymer throughfree radical polymerization between the double bonds on the surface of nano silicon dioxide andstyrene under the action of initiating agent. The dispersibility of nano silicon dioxide and thecontrollability of surface modification of nano silicon dioxide can be greatly improved by themodification process.

Rain Erosion Behavior of Silicon Dioxide Films Prepared on Sapphire

Silicon dioxide （SiO2） films were prepared on sapphire （α-Al2O3） by radio frequency magnetron reactive sputtering in order to increase both transmission and rain erosion resistant performance of infrared domes of sapphire. Composition and structure of SiO2 films were analyzed by X-ray photoelectron spectroscopy （XPS） and X-ray diffraction （XRD）, respectively. The transmittance of uncoated and coated sapphire was measured using a Fourier transform infrared （FTIR） spectrometer. Rain erosion tests of the uncoated and coated sapphire were performed at 211 m/s impact velocity with an exposure time ranging from 1 to 8 min on a whirling arm rig. Results show that the deposited films can greatly increase the transmission of sapphire in mid-wave IR. After rain erosion test, decreases in normalized transmission were less than 1% for designed SiO2 films and the SiO2 coating was strongly bonded to the sapphire substrate. In addition, sapphires coated with SiO2 films had a higher transmittance than uncoated ones after rain erosion.

Removal of Chromium from Aqueous Solution Using Hybrid Membrane of Chitosan and Silicon Dioxide

Adsorption experiment from aqueous solutions containing known amount of chromium （Cr） using hybrid membrane of chitosan and silicon dioxide was explored to evaluate the efficiency of the membrane as sorbent for Cr（VI）. Some variable parameters such as pH, contact time and the dosage of the membrane were optimized. Adsorption isotherms of Cr（VI） onto the hybrid membrane were measured with varying initial concentrations under optimized condition. Furthermore, the sorption mechanism of Cr by the membrane was investigated by applying Langmuir and Freundlich isotherm equations to the data obtained. The surface morphology of the membrane was determined by SEM （scanning electron microscope） for material characterization. The concentrations of Cr in solution are determined by ICP-MS （inductively coupled plasma mass spectrometry）. Hybrid membrane of chitosan and silicon dioxide can be an efficient sorbent for Cr（VI）.

Chemical Analysis Method for Magnesia and Magnesia-Alumina Refractories——Gravimetric-Molybdenum Blue Photometric Method for Determination of Silicon Dioxide Content

This standard specifies the gravimetric-molybdenum blue photometric method for determination of silicon dioxide content.

Ginseng ameliorates pulmonary toxicity induced by silicon dioxide nanoparticles in rats

Objective:To investigate the protective and therapeutic role of ginseng against silicon dioxide nanoparticles(SiO2NPs)-induced toxicity in the lungs.Methods:Sixty male rats were divided into five groups(n=12/group);group 1 was used as a control,group 2 received ginseng,group 3 was treated with SiO2NPs,and group 4 was pretreated with ginseng one week before SiO2NPs,while group 5 was given SiO2NPs one week before supplementation with ginseng.Animals were treated with both ginseng and SiO2NPs orally for five weeks.Real-time PCR was used to measure gene expression.Besides,DNA damage and cell cycle changes were determined by comet assay and flow cytometry,respectively.Histological study was also done to assess the effect of ginseng on SiO2NPs-induced toxicity.Results:SiO2NPs increased lipid peroxidation and decreased the activities of antioxidant enzymes.SiO2NPs induced apoptosis in lung tissues as revealed by upregulation of Bax and caspase 3 and downregulation of Bcl-2 as well as the induction of DNA damage.SiO2NPs also caused inflammation as indicated by upregulation of the inflammation-related genes[interleukin 1 beta(IL-1β),tumor necrosis factor-alpha(TNF-α),nuclear factor kappa B(NF-κB),cyclooxygenase 2(COX2),and transforming growth factor-beta 1(TGFβ1)]as well as cell cycle arrest in the G0/G1 phase of lung cells.Moreover,histopathological examination proved the biochemical and molecular perturbations that occurred due to SiO2NPs toxicity.However,ginseng alleviated SiO2NPs-induced toxicity in rat lung.Conclusions:Ginseng has a potent preventive and therapeutic effect and could be used in the treatment of SiO2NPs-induced pulmonary toxicity.

Enhanced etching of silicon didioxide guided by carbon nanotubes in HF solution

This paper describes a new method to create nanoscale SiO2 pits or channels using single-walled carbon nanotubes （SWNTs） in an HF solution at room temperature within a few seconds. Using aligned SWNT arrays, a pattern of nanoscale SiO2 channels can be prepared. The nanoscale SiO2 patterns can also be created on the surface of three- dimensional （3D） SiO2 substrate and even the nanoscale trenches can be constructed with arbitrary shapes. A possible mechanism for this enhanced etching of SiO2 has been qualitatively analysed using defects in SWNTs, combined with H3O＋ electric double layers around SWNTs in an HF solution.

Preparation and Characterization of CA-MA Eutectic/Silicon Dioxide Nanoscale Composite Phase Change Material from Water Glass via Sol-Gel Method

This work mainly involved the preparation of a nano-scale form-stable phase change material（PCM） consisting of capric and myristic acid（CA-MA） binary eutectic acting as thermal absorbing material and nano silicon dioxide（nano-SiO_2） serving as the supporting material. Industrial water glass for preparation of the nano silicon dioxide matrix and CA-MA eutectic mixture were compounded by single-step sol-gel method with the silane coupling agent. The morphology, chemical characterization and form stability property of the composite PCM were investigated by transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, Fourier-transform infrared（FT-IR） spectroscopy and polarizing microscopy（POM）. It was indicated that the average diameter of the composite PCM particle ranged from 30-100 nm. The CA-MA eutectic was immobilized in the network pores constructed by the Si-O bonds so that the composite PCM was allowed no liquid leakage above the melting temperature of the CA-MA eutectic. Differential scanning calorimetry（DSC） and thermogravimetric analysis（TGA） measurement were conducted to investigate the thermal properties and stability of the composite PCM. From the measurement results, the mass fraction of the CA-MA eutectic in the composite PCM was about 40%. The phase change temperature and latent heat of the composite were determined to be 21.15 ℃ and 55.67 J/g, respectively. Meanwhile, thermal conductivity of the composite was measured to be 0.208 W·m^（-1）·K^（-1） by using the transient hot-wire method. The composite PCM was able to maintain the surrounding temperature close to its phase change temperature and behaved well in thermalregulated performance which was verified by the heat storage-release experiment. This kind of form-stable PCM was supposed to complete thermal insulation even temperature regulation by the dual effect of relatively low thermal conductivity and phase change thermal storage-release properties. So it can be formulated that the nanoscale CA-MA/SiO_2 composite PCM with the form-stable property, good thermal storage capacity and relatively low thermal conductivity can be applied for energy conservation as a kind of thermal functional material.

An effective catalyst carrier SiO_(2):Enhancing catalytic and combustion properties of CuFe_(2)O_(4)on energetic components

To enhance the catalytic activity of copper ferrite(CuFe_(2)O_(4))nanoparticle and promote its application as combustion catalyst,a low-cost silicon dioxide(SiO_(2))carrier was employed to construct a novel CuFe_(2)O_(4)/SiO_(2)binary composites via solvothermal method.The phase structure,morphology and catalytic activity of CuFe_(2)O_(4)/SiO_(2)composites were studied firstly,and thermal decomposition,combustion and safety performance of ammonium perchlorate(AP)and 1,3,5-trinitroperhydro-1,3,5-triazine(RDX)with it affecting were then systematically analyzed.The results show that CuFe_(2)O_(4)/SiO_(2)composite can remarkably either advance the decomposition peak temperature of AP and RDX,or reduce the apparent activation energy at their main decomposition zone.Moreover,the flame propagation rate of RDX was promoted by about 2.73 times with SiO_(2)content of 3 wt%,and safety property of energetic component was also improved greatly,in which depressing the electrostatic discharge sensitivity of pure RDX by about 1.89 times.In addition,the effective range of SiO_(2)carrier content in the binary catalyst is found to be 3 to 5 wt%.Therefore,SiO_(2)opens a new insight on the design of combustion catalyst carrier and will promote the application of CuFe_(2)O_(4)catalyst in solid propellant.

Performance and Emission Characteristics of a CRDI Diesel Engine Fuelled by SiO_(2) Nanoparticle-Waste Fat Biodiesel Blends

This study investigates the use of waste fat biodiesel(WFB)from the leather industry as a substitute for diesel fuel.Specifically,it examines the diesel engine performance of WFB,a blend of WFB and diesel(B50),and different blends of WFB and silicon dioxide(SiO_(2))nanoparticles(B50SiO_(2)40,B50SiO_(2)80,and B50SiO_(2)120μg/g).The results indicate that the B50SiO_(2)120 blend increases brake thermal efficiency by 10.03%compared to pure biodiesel but falls 1.93%short of neat diesel.Furthermore,the B50SiO_(2)120 mixture reduces smoke,hydrocarbon,and carbon monoxide emissions by 31.87%,34.14%,and 43.97%respectively,compared to diesel.However,the B50SiO_(2)120 blend shows a 4.91%increase in nitrogen oxide emissions compared to diesel.

Deposition of Thick SiO_2 from Tetraethylorthosilicate and H_2O by Plasma-Enhanced CVD

The deposition of silicon dioxide by plasma enhanced chemical vapor deposition from tetraethylorthosilicate (TEOS) and H_2O has been studied.Silicon oxide with refractive index of 1453 has been obtained.Tests on the 51mm wafers show that both thickness uniformity of ±15% and constant refractive index of 1453 can be achieved.By raising the deposition temperature,the qualities have been improved,while the deposition rate decreased.A SiO_2 thick film deposition technique has been developed combining TEOS-PECVD technique with high temperature annealing.

Fabrication of Porous Silica Microspheres Under the Assistance of Solid Template

Spherical porous silica microparticles were synthesized by a sol-gel process in the presence of porous CaCO3 particles, followed by removal of the carbonate templates. The resulting silica particles had very high porosity and wide pore size distribution, whose surface area and pore volume reached up to 367.3 m2/g and 0.72 mL/g, re- spectively. With a larger amount of the tetraethyl orthosilicate used, hollow silica microspheres were further obtained. Characterization was made to confirm the chemical and physical structures and purity of the silica microspheres. Spontaneous deposition of tetramethyl rhodamine isothiocyanate labeled dextran into the microspheres was also ob- served due to the charge attraction.

Effect of SiO_2 addition on the microstructure and electrical properties of ZnO-based varistors

The microstructure and electrical properties of ZnO-based varistors with the SiO2 content in the range of 0-1.00mol% were prepared by a solid reaction route. The varistors were characterized by scanning electron microscopy, X-ray diffraction, energy-dispersive X-ray spectrometry, inductively coupled plasma-atomic emission spectrometry, and X-ray photoelectron spectroscopy. The results indicate that the average grain size of ZnO decreases with the SiO2 content increasing. A new second phase （Zn2SiO4） and a glass phase （Bi2SiO5） are found. Element Si mainly exists in the grain boundary and plays an important role in controlling the Bi2O3 vaporization. The electric measurement shows that the incorporation of SiO2 can significantly improve the nonlinear properties of ZnO-based varistors, and the nonlinear coefficients of the varistors with SiO2 are in the range of 36.8-69.5. The varistor voltage reaches the maximum value of 463 V/mm and the leakage current reaches the minimum value of 0.11 μA at the SiO2 content of 0.75mol%.

Preparation and Characterization of Sodium Sulfate/Silica Composite as a Shape-stabilized Phase Change Material by Sol-gel Method

A sodium sulfate （NaeSO4）/silica （SiO2） composite was prepared as a shape-stabilized solid-liquid phase change material by a sol-gel procedure using Na2SiO3 as the silica source. Na2SO4 in the composite acts as a latent heat storage substance for solid-liquid phase change, while SiO2 acts as a support material to provide structural strength and prevent leakage of melted NazSO4. The microstructure and composition of the prepared composite were characterized by the N2 adsorption, transmission electron microscope （TEM）, scanning electron microscope （SEM）, Fourier transform infrared spectroscopy （FTIR） and X-ray diffraction. The results show that the prepared Na2SOJSiO2 composite is a nanostructured hybrid of NazSO4 and SiO2 without new substances produced during the phase change. The macroscopic shape of the NazSO4/SiO2 composite after the melting and freezing cycles does not change and there is no leakage of Na2SO4. Determined by differential scanning calorimeter （DSC） analysis, the values of phase change latent heat of melting and freezing of the prepared NazSO4/SiO2 （50%, by mass） composite are 82.3 kJ.kg i and 83.7 kJ.kg-1, and temperatures of melting and freezing are 886.0 ℃ and 880.6 ℃, respectively. Furthermore, the Na2SOJSiO2 composite maintains good thermal energy storage and release ability even after 100 cycles of melting and freezing. The satisfactory thermal storage performance renders this composite a versatile tool for high-temperature thermal energy storage.

Desiliconization kinetics of nickeliferous laterite ores in molten sodium hydroxide system

A novel process was proposed for treating nickeliferous laterite ores with molten sodium hydroxide.The effect on silicon extraction caused by the factors,such as stirring speed,reaction temperature,particle size and NaOH-to-ore mass ratio,was investigated.The results show that increasing stirring speed,reaction temperature and NaOH-to-ore mass ratio while decreasing particle size increases silicon extraction rate.The desiliconization kinetics of nickeliferous laterite ores in molten sodium hydroxide system was described successfully by chemical reaction control model.The activation energy of the desiliconization process was found to be 44.01 kJ/mol,and the reaction rate based on a chemical reaction-controlled process can be expressed as:1-(1-α) 1/3 = 27.67exp[-44 010/(RT)]t.

A1_2O_3 Effect on the Catalytic Activity of Cu-ZnO-Al_2O_3-SiO_2 Catalysts for Dimethyl Ether Synthesis from CO_2 Hydrogenation

The effect of Al2O3 on the Cu-ZnO-Al2O3-SiO2 catalysts prepared by a pseudo sol-gel method has been investigated and these catalysts were characterized by XRD, H2-TPR, XPS, NH3-TPD and CO2- TPD techniques. As revealed by XRD and H2-TPR, the added alumina produces high dispersion of CuO and makes the reduction of CuO difficult. XPS analysis detects a remarkably high Al^3＋ enrichment at the surface of calcined samples, along with a decrease of Eb of Cu 2p3/2, which confirms the Cu-Al interaction. Another important role of Al203 would be to incorporate into the SiO2 structure to form the acid-base sites for ether formation. The reaction results shows that the addition of Al2O3 exhibits a promoting effect on the CO2 conversion only when its content is below 1.4%, and an optimal DME selectivity is obtained when 4.0%Al2O3 is added, indicating a better ＇synergistic effect＇ is present between the methanol forming component and the acidic component in bifunctional catalysts. Possible relationship between the catalytic activity and the Cu-Al interaction as well as the surface acidity is discussed.

Desilication kinetics of calcined boron mud in molten sodium hydroxide media

Desilication kinetics of calcined boron mud(CBM) occurring in molten sodium hydroxide media was investigated. The effects of factors such as reaction temperature and Na OH-to-CBM mass ratio on silicon extraction efficiency were studied. The results show that silicon extraction efficiency increases with increasing the reaction time and Na OH-to-CBM mass ratio. There are two stages for the desilication process of the calcined boron mud. The overall desilication process follows the shrinking-core model, and the first and second stages of the process were determined to obey the shrinking-core model for surface chemical reaction and the diffusion through the product layer, respectively. The activation energies of the first and second stages were calculated to be 44.78 k J/mol and 15.94 k J/mol, respectively.

STRUCTURE AND PROPERTIES OF COMPOSITE POLYURETHANE HOLLOW FIBER MEMBRANES

Composite polyurethane(PU)-SiO_2 hollow fiber membranes were successfully prepared via optimizing thetechnique of dry-jet wet spinning,and their pressure-responsibilities were confirmed by the relationships of pure water flux-transmembrane pressure(PWF-TP)for the first time.The origin for this phenomenon was analyzed on the basis of membranestructure and material characteristics.The effects of SiO_2 content on the structure and properties of membrane wereinvestigated.The experimental results indicated that SiO_2 in membrane created a great many interfacial micro-voids andplayed an important role in pressure-responsibility,PWF and rejection of membrane:with the increase of SiO_2 content,theability of membrane recovery weakened,PWF increased,and rejection decreased slightly.