A Light and Simplified Branch Bending Method for Young Pear Trees

Aiming at high cost and low efficiency of conventional branch bending method in the modern intensive planting and labor-saving cultivation mode of young pear trees,this paper provides a new branch bending method with wide source of raw materials,cheap price and simple operation,which is also suitable for the management of low-age branches in the process of high grafting and upgrading of traditional big trees.

An Improved Simplified Method for Predicting the Hydroelastic Response of Mat-Like VLFS

Very Large Floating Structures (VLFS) have received considerable attention recently. Efficient and accurate estimation of their hydroelastic responses in waves is very important for the design. The most efficient approach would obviously be the analytical one, Within the category of analytical approaches, the simplified method proposed by Ohkusu and his colleague are of special characteristics. However, when one studies their methods, several questions arise. The purpose of this paper is to critically study the simplified methods proposed by Ohkusu and his colleague in order to answer these questions. Some problems in their original methods have been found and possible improvements are suggested. It is concluded that the improved simplified method using the same idea of Ohkusu and his colleague could provide a reasonable estimate of the hydroelastic response of mat-like VLFS in a certain range of incident angles of waves.

Simplified Calculation Methods for All-Vertical-Piled Wharf in Offshore Deep Water

All-vertical-piled wharf is a kind of high-piled wharf, but it is extremely different from the traditional ones in some aspects, such as the structural property, bearing characteristics, failure mechanism, and static or dynamic calculation methods. In this paper, the finite element method （FEM） and theoretical analysis method are combined to analyze the structural property, bearing behavior and failure mode of the all-vertical-piled wharf in offshore deep water, and to establish simplified calculation methods determining the horizontal static ultimate bearing capacity and the dynamic response for the all-vertical-piled wharf. Firstly, the bearing capability and failure mechanism for all-vertical-piled wharf are studied by use of FEM, and the failure criterion is put forward for all-vertical-piled wharf based on the ＇plastic hinge＇. According to the failure criterion and P-Y curve method, the simplified calculation method of the horizontal static ultimate bearing capacity for all-vertical-piled wharf is proposed, and it is verified that the simplified method is reasonable by comparison with the FEM. Secondly, the displacement dynamic magnification factor for the all-vertical-piled wharf under wave cyclic loads and ship impact loads is calculated by the FEM and the theory formula based on the single degree of freedom （SDOF） system. The results obtained by the two methods are in good agreement with each other, and the simplified calculation method of the displacement dynamic magnification factor for all-vertical-piled wharf under dynamic loads is proposed. Then the simplified calculation method determining the dynamic response for the all-vertical-piled wharf is proposed in combination with P-Y curve method. That is, the dynamic response of the structure can be obtained through the static calculation results of P-Y curve method multiplied by the displacement dynamic magnification factor. The feasibility of the simplified dynamic response method is verified by comparison with the FEM under different conditions.

Simplified Homogeneous Balance Method and Its Applications to the Whitham-Broer-Kaup Model Equations

A nonlinear transformation of the Whitham-Broer-Kaup (WBK) model equations in the shallow water small-amplitude regime is derived by using a simplified homogeneous balance method. The WBK model equations are linearized under the nonlinear transformation. Various exact solutions of the WBK model equations are obtained via the nonlinear transformation with the aid of solutions for the linear equation.

A simplified method for prediction of embankment settlement in clays

The prediction of embankment settlement is a critically important issue for the serviceability of subgrade projects,especially the post-construction settlement.A number of methods have been proposed to predict embankment settlement;however,all of these methods are based on a parameter,i.e.the initial time point.The difference of the initial time point determined by different designers can de?nitely induce errors in prediction of embankment settlement.This paper proposed a concept named"potential settlement"and a simpli?ed method based on the in situ data.The key parameter"b"in the proposed method was veri?ed using theoretical method and?eld data.Finally,an example was used to demonstrate the advantages of the proposed method by comparing with other methods and the observation data.

Dynamic Characteristics and Simplified Numerical Methods of An All-Vertical-Piled Wharf in Offshore Deep Water

There has been a growing trend in the development of offshore deep-water ports in China. For such deep sea projects, all-vertical-piled wharves are suitable structures and generally located in open waters, greatly affected by wave action. Currently, no systematic studies or simplified numerical methods are available for deriving the dynamic characteristics and dynamic responses of all-vertical-piled wharves under wave cyclic loads. In this article, we compare the dynamic characteristics of an all-vertical-piled wharf with those of a traditional inshore high-piled wharf through numerical analysis; our research reveals that the vibration period of an all-vertical-piled wharf under cyclic loading is longer than that of an inshore high-piled wharf and is much closer to the period of the loading wave. Therefore, dynamic calculation and analysis should be conducted when designing and calculating the characteristics of an all-vertical-piled wharf. We establish a dynamic finite element model to examine the dynamic response of an all-vertical-piled wharf under wave cyclic loads and compare the results with those under wave equivalent static load; the comparison indicates that dynamic amplification of the structure is evident when the wave dynamic load effect is taken into account. Furthermore, a simplified dynamic numerical method for calculating the dynamic response of an all-vertical-piled wharf is established based on the P-Y curve. Compared with finite element analysis, the simplified method is more convenient to use and applicable to large structural deformation while considering the soil non-linearity. We confirmed that the simplified method has acceptable accuracy and can be used in engineering applications.

Adaptive hp finite element method for fluorescence molecular tomography with simplified spherical harmonics approximation

Recently,the simplified spherical harmonics equations(SP)model has at tracted much att entionin modeling the light propagation in small tissue ggeometriesat visible and near-infrared wave-leng ths.In this paper,we report an eficient numerical method for fluorescence moleeular tom-ography(FMT)that combines the advantage of SP model and adaptive hp finite elementmethod(hp-FEM).For purposes of comparison,hp-FEM and h-FEM are,respectively applied tothe reconstruction pro cess with diffusion approximation and SPs model.Simulation experiments on a 3D digital mouse atlas and physical experiments on a phantom are designed to evaluate thereconstruction methods in terms of the location and the reconstructed fluorescent yield.Theexperimental results demonstrate that hp-FEM with SPy model,yield more accurate results thanh-FEM with difusion approximation model does.The phantom experiments show the potentialand feasibility of the proposed approach in FMT applications.

Simplified Method and Influence Factors of Vibration Characteristics of Isolated Curved Girder Bridge

The isolated curved girder bridge's vibration characteristics play a major part in the seismic responses of structures and anti-seismic properties.A clear analytic relationship between design parameters and the system's vibration characteristics could be established by its simplified dynamic analysis model,making it convenient for providing a reference to the optimization of design and safety analysis.A double-mass six-degree-of-freedom model for curved girder bridges with isolation bearings installed at the top of the bridge piers is built and a simplified analysis method for the vibration characteristics of the system is provided.Combined with the Matlab programming,the influences of radius of curvature,central angle,bridge deck width and damping ratio of the isolation layer and circular frequency of the isolation layer of isolated curved girder bridges on the pseudo-undamped natural circular frequency(called pseudo-frequency for short)and system damping ratio are systematically analyzed,and the sensitivity of vibration characteristics of isolated curved girder bridges is studied.The results show that the vibration characteristics of isolated curved girder bridges can be reflected well with this simplified model and calculation method.The pseudo-frequency of curved girder and system damping ratios increases with the increase of the isolation layer.The third-order vibration characteristic is more sensitive to the parameters of a curved girder,and the first-order vibration characteristic is sensitive to both central angle and radius of curvature to some extent while insensitive to the width of the bridge deck.Furthermore,the second-order vibration characteristic is not sensitive to the parameters of a curved girder.

A comparative study between simplified and nonlinear dynamic methods for estimating liquefaction potential

This paper estimated the liquefaction potential of a saturated soil deposit subjected to a horizontal seismic excitation at its base using the total stress approach.A comparative analysis between the simplified and the nonlinear dynamic methods was used to verify to what extent the simplified method could be reliable.In order to generalise the reliability of the simplified method for any value of the maximum acceleration for the used earthquakes,a correction for the maximum acceleration less than 0.3 g was proposed based on the comparison of safety factor values determined by the dynamic method illustrated by the equivalent linear model with lumped masses and the simplified method for a given profile of soil subjected to 38 earthquakes.The nonlinear behaviour of soil was represented by two hyperbolic models:Hardin and Drnevich,and Masing.To determine the cyclic resistance ratio(CRR),the cone penetration test(CPT) based method,the standard penetration test(SPT) based method,and the shear wave velocity based method were used.The safety factor was calculated as the ratio of CRR/CSR,where CSR represents the cyclic stress ratio.The results of the proposed correction have given smaller values of the safety factor compared to the nonlinear dynamic methods for the maximum acceleration less than 0.3 g.In other words,by considering this correction,the most unfavourable case is always given by the modified simplified method.

A simplified dynamic method for field capacity estimation and its parameter analysis

This paper presents a simplified dynamic method based on the definition of field capacity. Two soil hydraulic characteristics models, the Brooks-Corey （BC） model and the van Genuchten （vG） model, and four soil data groups were used in this study. The relative drainage rate, which is a unique parameter and independent of the soil type in the simplified dynamic method, was analyzed using the pressure-based method with a matric potential of -1/3 bar and the flux-based method with a drainage flux of 0.005 cm/d. As a result, the relative drainage rate of the simplified dynamic method was determined to be 3% per day. This was verified by the similar field capacity results estimated with the three methods for most soils suitable for cultivating plants. In addition, the drainage time calculated with the simplified dynamic method was two to three days, which agrees with the classical definition of field capacity. We recommend the simplified dynamic method with a relative drainage rate of 3% per day due to its simple application and clearly physically-based concept.

Simplified Method and Improved Solution for Deriving Fifth Order Stokes Wave

As the solution of the two equations for determining the existing fifth order Stokes wave derived by Skjelbreia is complex and tedious, the two equations are simplified into one equation for determining d / L, i. e., f(H, T, d / L) = 0. According to this simplified method, three cases of the solution for the Skjelbreia equations have been found: one accurate solution; more than one accurate solution and no accurate solution (but there exists the optimum approximate solution in the area of satisfying Skjelbreia equations). As to the case of more than one accurate solution, the reasonable solution can be judged from the method of variational principle, by means elf which an optimum solution improved from the solution of Skjelbreia equations in the area of satisfying the original mathematical equations of non-vortex and nonlinear wave theory, i. e., the optimum fifth order Stokes wave, is given.

A Simplified Hirota Method and Its Application

By means of the homogeneous balance principle, a nonlinear transformation to the well known breaking soliton equation with physical interest was given. The original equation was turned into a homogeneity differential equation with this nonlinear transformation. By solving the homogeneity equation via the simplified Hirota method and applying the nonlinear transformation, one soliton, two soliton and three soliton solutions as well as some other types of explicit solutions to the breaking soliton equation were obtained with the assistance of Maple.

Sensorless Control of Double-sided Linear Switched Reluctance Motor Based on Simplified Flux Linkage Method

The utilization of position sensor reduces the system reliability of switched reluctance motor(SRM),especially in harsh environments.It also increases the complexity of the system.Therefore,the research on sensorless control has become one of the hot spots in recent years.Comparing with the existing sensorless control technology,the new method exploring the sensorless control of double-sided linear switched reluctance motor(DLSRM)shows the following advantages:1)high accuracy,and 2)good practicability.Based on the new proposed method,the DLSRM speed controller is augmented with the peak current method and the voltage chopping closed-loop speed control.Moreover,the winding resistance in the equation is corrected according to the integral flux linkage when the phase current is zero.The accuracy and feasibility of the simplified flux linkage method in estimating the position of the DLSRM is verified.

空时分数阶simplified modified Camassa-Holm方程的新精确解

借助分数阶复变换,将分数阶偏微分方程转化为常微分方程,然后应用首次积分法,得到空时分数阶simpli⁃fied modified Camassa-Holm方程的新精确解,其中包括孤立波解、周期波解、有理函数解,丰富其精确解解系。

CHARACTER OF SIMPLIFIED NAVIER-STOKES EQUATIONS FOR NEAR THE LEADING EDGE PART OF TWO-DIMENSIONAL LAMINAR FLOW PAST A FLAT PLATE

Starting from the Simplified Navier-Stokes(SNS)equations presented at first by Godovachev-Kuzmin-Tsopov,and Gao Zhi,Davis,the authors analyze the character of the SNS equations for the laminarflow near the leading edge of a flat plate and far away from the plate by using the Weiner—Hopf meth-od and Fourier transform.It is proved that the solution of the SNS equations agree with the solution of the Navier-Stokes equations for flow near the leading edge of the plate and far away from the plate.How to match the solution of the SNS equations to the Blasius solution of the boundary layer equationsis also discussed.

Research on the Influencing Factors of Changes in Industrial Carbon Emissions in China: Based on Simplified D&L Model

The simplified D＆L method with special properties required by ideal decomposition method was used to decompose the impact of carbon emission intensity,input-output technology,the final demand structure and the final demand level on changes in industrial carbon emissions in China during 1997-2012. The results showed that the final demand level which was the most important factor leading to the growth of carbon emissions performed a steadily and significantly positive and sustained effect. The carbon emissions intensity which was the only factor that led to the reduction in carbon emissions showed a negative effect. The input-output technology showed a positive effect. The final demand structure underwent a transition from a negative effect to a weak positive effect and finally to a positive effect. In order to achieve the goal of total carbon emission control,China should take some measures such as reducing direct carbon emission coefficient to strengthen the negative impact of carbon emission intensity. Meanwhile,China should implement some structural adjustment measures such as optimizing the final demand structure and reducing the proportion of industries with a great increase of influence coefficient to change the input-output technology and the final demand structure from the positive effect to the negative effect.

基于损伤等效的直立锁边屋面板动态抗风揭试验方法

围护结构在台风等极端风下的抗风性能需要依靠动态试验测定,试验周期长导致成本高且模拟研究受限。基于直立锁边屋面板材料的损伤本构模型,通过疲劳分析研究荷载幅值对材料损伤影响,提出简化荷载序列组合。借助雨流计数法统计测点风压时程得到基于损伤等效的简化荷载循环,提出动态抗风揭试验方法。参照不同试验方法开展抗风揭试验,通过对比发现,试验方法对屋面板风揭破坏过程影响不明显。除永久塑性变形外,该文试验方法与现有试验方法下屋面板损坏现象基本一致,屋面板均为撕裂破坏。不同试验方法下屋面板承载力差异在10%~20%间。该文试验方法加载周期小于1h,现有试验方法加载周期则大于20h。在屋面板风揭破坏过程、承载力等抗风揭性能差异不大情况下,该文试验方法可大幅降低试验周期,为开展模拟研究奠定基础。

地下管廊抗震研究现状综述

针对地下管廊工程建设高速发展、抗震减灾需求愈发凸显的现状,综述地下管廊抗震研究现状.首先,通过国内外以往的震害实例,对地下管廊的震害形式、震害影响因素及震害机理进行了系统性总结.其次,从拟静力试验和振动台试验两个方面总结了地下管廊抗震性能的试验研究现状.再次,总结了地下管廊抗震分析的简化分析方法、动力时程方法、地震易损性评估及减隔震技术的研究现状.最后,基于文献综述提出了目前地下管廊抗震研究亟待解决的问题并做出展望,以期促进地下管廊抗震研究的发展.研究表明:地下管廊在地震作用下的破坏形式主要有混凝土剥落、裂缝贯通、接缝错位或张开、管廊受剪断裂等;地震作用下地下管廊穿越非均匀场地时动力响应的放大效应显著,地下管廊穿越软硬交互等非均匀场地时的抗震性能研究值得重视;交叉节点是地下管廊的薄弱环节,交叉管廊的抗震设计方法研究值得关注;预制管廊接头易受到地震破坏,不同类型预制管廊接头的抗震性能研究需深入探索;城市大型地下管廊系统抗震性能受到不同交叉节点和不同管廊之间的交互影响,高效的地下管廊系统建模方法和高效的简化分析方法亟待研究;城市大型地下管廊系统地震易损性分析是重要的发展方向;地下管廊的减隔震技术值得发展.

盾构下穿引起上覆管线变形的简化计算方法

盾构开挖易引起上覆地表沉降变形,进一步会引起上覆既有管线的受力变形响应.基于此,提出了一种盾构开挖引起上覆管线变形的简化计算方法.首先采用Loganathan公式获得既有管线在盾构下穿影响下的附加应力,进一步将管线简化成无限长梁放置在Pasternak地基上,引入无限远端侧向土体位移对既有管线的影响,采用力学平衡法获得管线竖向受力变形控制方程,通过有限差分法获得管线变形及其内力数值解析.案例分析表明:与退化解析对比,该方法计算结果更贴近既有文献工程实测数据,验证了其可靠性.进一步参数研究表明:增大隧道与管线的竖向净距会引起既有管线受力变形的非线性减小;管线变形及其内力会随着地层损失率增大而线性增大;管线抗弯刚度的增大会引起管线变形减小,但会大幅增加管线弯矩.

利用简化曲线交会法初步确定HDPE土工膜厚度

采用曲线交会法确定平原水库库盘土工膜厚度时,存在材料特性曲线难获得、需多次读图取数、重复试验次数多、可选择性小等不便之处。为此,基于曲线交会法的基本原理和材料弹性阶段的线弹性与双曲线应力-应变本构关系,推导了初步确定高密度聚乙烯(HDPE)土工膜厚度的简化曲线交会法(包括简化线弹性法和简化双曲线法),并对新疆某平原水库HDPE土工膜厚度的选取进行了计算分析。结果表明:(1)与曲线交会法相比,简化曲线交会法计算误差较小,拉应力安全系数误差平均约为2.22%,应变安全系数误差平均约为-4.24%,说明该方法较为准确合理;(2)当其他条件相同时,正方形孔隙拉应力安全系数最低,以其为该工程安全运用的判断基准;(3)对同一孔隙条件,安全系数随土工膜厚度增加而增加,且呈近似线性关系;(4)通过计算得到满足安全系数要求的HDPE土工膜厚度范围为≥0.5 mm。简化曲线交会法有助于土工膜厚度确定时的便捷计算,可以满足工程设计阶段初步确定HDPE土工膜厚度的要求。