Damage constitutive model of lunar soil simulant geopolymer under impact loading

Lunar base construction is a crucial component of the lunar exploration program,and considering the dynamic characteristics of lunar soil is important for moon construction.Therefore,investigating the dynamic properties of lunar soil by establishing a constitutive relationship is critical for providing a theoretical basis for its damage evolution.In this paper,a split Hopkinson pressure bar(SHPB)device was used to perform three sets of impact tests under different pressures on a lunar soil simulant geopolymer(LSSG)with sodium silicate(Na_(2)SiO_(3))contents of 1%,3%,5%and 7%.The dynamic stressestrain curves,failure modes,and energy variation rules of LSSG under different pressures were obtained.The equation was modified based on the ZWT viscoelastic constitutive model and was combined with the damage variable.The damage element obeys the Weibull distribution and the constitutive equation that can describe the mechanical properties of LSSG under dynamic loading was obtained.The results demonstrate that the dynamic compressive strength of LSSG has a marked strain-rate strengthening effect.Na_(2)SiO_(3) has both strengthening and deterioration effects on the dynamic compressive strength of LSSG.As Na_(2)SiO_(3) grows,the dynamic compressive strength of LSSG first increases and then decreases.At a fixed air pressure,5%Na_(2)SiO_(3) had the largest dynamic compressive strength,the largest incident energy,the smallest absorbed energy,and the lightest damage.The ZWT equation was modified according to the stress response properties of LSSG and the range of the SHPB strain rate to obtain the constitutive equation of the LSSG,and the model’s correctness was confirmed.

Multiple chemical warfare agent simulant decontamination by self-driven microplasma

Low-temperature plasma is a green and high-efficiency technology for chemical warfare agent(CWA)decontamination.However,traditional plasma devices suffer from the problems of highpower composition and large power-supply size,which limit their practical applications.In this paper,a self-driven microplasma decontamination system,induced by a dielectric-dielectric rotary triboelectric nanogenerator(dd-r TENG),was innovatively proposed for the decontamination of CWA simulants.The microplasma was characterized via electrical measurements,optical emission spectra and ozone concentration detection.With an output voltage of-3460 V,the dd-r TENG can successfully excite microplasma in air.Reactive species,such as OH,O(1D),Hαand O3were detected.With input average power of 0.116 W,the decontamination rate of 2-chloroethyl ethyl sulfide reached 100%within 3 min of plasma treatment,while the decontamination rates of malathion and dimethyl methylphosphonate reached(65.92±1.65)%and(60.88±1.92)%after 7 min of plasma treatment,respectively.In addition,the decontamination rates gradually decreased with the increase in the simulant concentrations.Typical products were identified and analyzed.This study demonstrates the broad spectrum and feasibility of the dd-r TENG-microplasma for CWA elimination,which provides significant guidance for their practical applications in the future.

Ballistic response of skin simulant against fragment simulating projectiles

The response of biological phantoms against high velocity impact is actively sought for applications in defense,space,soft robotics and sensing.Towards this end,we study the ballistic response of silicone based skin simulant against fragment impact.Using a pneumatic gas gun setup,six chisel-nosed and three regular shaped(sphere,cylinder,and cube)fragments were impacted on the skin simulant.The resulting skin simulant response was studied in terms of ballistic limit velocities,energy densities,failure pattern,and the mechanics of interaction.The results indicate that the shape of the fragment affects the ballistic limit velocities.The ballistic limit velocities,energy densities of the chisel-nosed fragment simulating projectiles were relatively insensitive to the size(mass),except for the smallest(0.16 g)and largest(2.79 g)chisel-nosed fragment.For the same size(1 g),ballistic limit velocities and failure are dependent on the shape of the fragment.The skin simulant failed by combined plugging and elastic hole enlargement.Failure in the spherical fragment was dominated by the elastic hole enlargement,whereas plugging failure was dominant in all other fragments.The spherical,cylindrical,and chisel-nosed fragments created circular cavities,and the cubical fragment created a square cavity.In the case of the spherical fragment,slipping of the fragment within the skin simulant was seen.Cubical fragments created lateral cracks emanating from the corners of the square cavity.Interestingly,for all the fragments,the maximum deformation corresponding to the perforation was lower than the non-perforation indicating rate dependent,stress driven failure.The maximum deformation was also dependent on the shape of the fragment.Overall,these results provide unique insights into the mechanical response of a soft simulant against ballistic impact.Results have utility in the calibration and validation of computational models,design of personal protective equipment,and antipersonnel systems.

Selection and thermal physical characteristics analysis of in-situ condition preserved coring lunar rock simulant in extreme environment

With the increasing scarcity of Earth’s resources and the development of space science and technology,the exploration, development, and utilization of deep space-specific material resources(minerals, water ice, volatile compounds, etc.) are not only important to supplement the resources and reserves on Earth but also provide a material foundation for establishing extraterrestrial research bases. To achieve large depth in-situ condition-preserved coring(ICP-Coring) in the extreme lunar environment, first, lunar rock simulant was selected(SZU-1), which has a material composition, element distribution, and physical and mechanical properties that are approximately equivalent to those of lunar mare basalt. Second, the influence of the lunar-based in-situ environment on the phase, microstructure, and thermal physical properties(specific heat capacity, thermal conductivity, thermal diffusivity, and thermal expansion coefficient)of SZU-1 was explored and compared with the measured lunar rock data. It was found that in an air atmosphere, low temperature has a more pronounced effect on the relative content of olivine than other temperatures, while in a vacuum atmosphere, the relative contents of olivine and anorthite are significantly affected only at temperatures of approximately-20 and 200 ℃. When the vacuum level is less than100 Pa, the contribution of air conduction can be almost neglected, whereas it becomes dominant above this threshold. Additionally, as the testing temperature increases, the surface of SZU-1 exhibits increased microcracking, fracture opening, and unevenness, while the specific heat capacity, thermal conductivity,and thermal expansion coefficient show nonlinear increases. Conversely, the thermal diffusivity exhibits a nonlinear decreasing trend. The relationship between thermal conductivity, thermal diffusivity, and temperature can be effectively described by an exponential function(R^(2)>0.98). The research results are consistent with previous studies on real lunar rocks. These research findings are expected to be applied in the development of the test and analysis systems of ICP-Coring in a lunar environment and the exploration of the mechanism of machine-rock interaction in the in-situ drilling and coring process.

On Modeling Drilling Load in Lunar Regolith Simulant

Drilling and coring, as effective ways to obtain lunar regolith along the longitudinal direction, are widely applied in the lunar sampling field. Conventionally, modeling of drill-soil interaction was divided into soil cutting and screw conveyance processes, ignoring the differences in soil mechanical properties between them. To improve the modeling accuracy, a hypothesis that divides the drill-soil interaction into four parts: cuttings screw conveyance, cuttings extruding, cuttings bulldozing, and in situ simulant cutting, is proposed to establish a novel model based on the passive earth pressure theory. An iterative numerical calculation method is developed to predict the drilling loads. A drilling and coring testbed is developed to conduct experimental tests. Drilling experiments indicate that the drilling loads calculated by the proposed model match well the experimental results. The proposed research provides the instructions to adopt a suitable drilling strategy to match the rotary and penetrating motions, to increase the safety and reliability of drilling control in lunar sampling missions.

STUDIES ON SOLUBILIZATION AND TRANSFORMATION OF SPECIES OF Cu，Pb．Zn AND Cr IN SIMULANT ACID RAIN

The effect of acid rain on spectes of Cu Pb. Zn and Cr has been studied by Tessler net method In simulart acld rain the content of Cu and Cr increased with decreasing pll. whereas solubiliztion content of Pb and Zn has a peak value at pll= 3.5.4.5respectively which come from the exchangeable and carbonate-bound fractions in the first place. In addition, the content of varions species of Cu. Pb. Zn and Cr change greal in simalant acid rain. Copper transforms from superior fform (bound to organic matter ) to exchangeable, bound to carbonates and bound to Fe-Mc orldes while fead zine and chromiam transform from bound to Fe-Mn oxides to exchangeable and bound to carbocatesWith the development of industry. more Sox and more SOx and NOx are discharged into the air and the rainfall becomes caid this makes particulate metals more active and toxic.

Preparation and Characterization of High-Strength Geopolymer Based on BH-1 Lunar Soil Simulant with Low Alkali Content

The construction of a lunar base and habitation on the Moon has always been on researchers’minds.Building materials used in in situ lunar resources are of great significance for saving expensive space freight.In this study,a new type of lunar soil simulant named Beihang(BH)-1 was developed.The chemical mineral composition and microstructure of BH-1 closely resemble those of real lunar soil,as verified by X-ray fluorescence spectroscopy(XRF),X-ray diffraction(XRD),scanning electron microscopy(SEM),and reflectance spectra.This research also synthesized a geopolymer based on BH-1 cured at simulated lunar atmospheric conditions.We also investigated the effect of supplementing aluminum(Al)sources on the enhancement of geopolymer strength based on BH-1.The rheological behavior of alkali-activated BH-1 pastes was determined for workability.XRF,XRD,Fourier transform infrared spectroscopy,SEM coupled with energy dispersive spectroscopy,and 27Al magic angle spinningnuclear magnetic resonance were used to characterize resulting geopolymers.Rheological test findings showed that the rheology of BH-1 pastes fits the Herschel–Bulkley model,and they behaved like a shear-thinning fluid.The results showed that the 28-day compressive strength of the BH-1 geopolymer was improved by up to 100.8%.Meanwhile,the weight of additives required to produce per unit strength decreased,significantly reducing the mass of materials transported from the Earth for the construction of lunar infrastructure and saving space transportation costs.Microscopic analyses showed that the mechanism to improve the mechanical properties of the BH-1 geopolymer by adding an additional Al source enhances the replacement of silicon atoms by Al atoms in the silicon–oxygen group and generates a more complete and dense amorphous gel structure.

Preparation and characterization of a specialized lunar regolith simulant for use in lunar low gravity simulation

Lunar in-situ resource utilization(ISRU)has been put on the agenda by many countries.Due to the special material nature and low gravity environment,the lunar regolith demonstrates significantly different behavior from terrestrial geomaterials.However,the systematic understanding of its geotechnical behavior is now seriously restricted by the scarcity of lunar regolith and the difficulty in simulating lunar gravity.A new lunar regolith simulant,termed as China University of Mining and Technology Number One(CUMT-1),has been developed to recover properties of the lunar regolith and simulate the lunar gravity by adopting the recently advanced geotechnical magnetic-similitude-gravity model testing(GMMT)method.The CUMT-1 simulant was prepared by reproducing the in-situ formation and fragmentation of the lunar matrix,which plays a key role in the irregular particle morphology.The mineralogical compositions,particle morphology and gradation,specific gravity,bulk density,void ratio,shear strength,and compressibility were determined.After quantifying the magnetization and magnetic-similitude-gravity characteristics,an application of the cone penetration resistance under low gravity was further given.The obtained results are compared to the values known for lunar regolith samples and other simulants,which demonstrates promising characteristics for use in geotechnical engineering-based and scientificbased applications,especially considering the influence of lunar gravity.

A novel specimen preparation method for TJ-1 lunar soil simulant in hollow cylinder apparatus

Conventional methods for hollow cylinder apparatus （HCA） specimen preparation are not applicable for T J-1 lunar soil simulant due to its wide particle size distribution. A novel method to prepare uniform T J-1 specimen for HCA tests is put forward. The method is a combination of the multi-layering dry-rodding method and a new under-compaction criterion in the multi-layer with under-compaction method （UCM）. In the novel method, the specimen is prepared with 5 layers by dry-rodding and the UCM is used to determine the height after each layer is compacted. The density uniformity of specimen is evaluated by the freezing method to find out the best under-compaction criterion. Two HCA specimens with the same target density are prepared by the novel method and examined in the tests of pure rotation of the principal stresses. Their conformable mechanical behaviors ascertain the effectiveness of the method to produce uniform and reproducible HCA specimens. Four groups of HCA tests are carried out to investigate the anisotropic and non-coaxial behaviors of TJ-I lunar soil simulant. The results indicate that the principal stress direction, the deviator stress ratio, the stress level and the coefficient of the intermediate principal stress significantly influence the strength and deformation properties of T J-1 lunar soil simulant.

Utilization of Various Analogy of Synthetic Nanoporous Zeolites and Composite of Zeolites for Decontamination/Detoxification of CWA Simulants—An Updated Review

In this review, we summaries the past few year work on the chemistry of CWA’s and their simulants on various heterogeneous surfaces of zeolites, composites of zeolites and doped zeolite with transition metal oxides. This review elaborates an updated literature overview on the degradation of CWA’s and its simulants. The data written in this review were collected from the peer-reviewed national and international literature.

Compressional Punch Loading Test of a Polymer Bonded Explosive Simulant Using Digital Image Correlation Method

Punch loading is a loading scenario to study the fracture mechanism of materials at low strain rates.In this paper,three punch loading experimental patterns were chosen for the study of compressional punch loading.A polymer bonded explosive（PBX） simulant was experimentally studied using the digital image correlation（DIC） method.The displacement and strain fields were obtained and the fracture behavior and failure mechanisms of samples were investigated under different punch loading conditions.Moreover,scanning electron microscope（SEM） was used to examine the region of the plastic flow and the damage in the material.The formation of slip bands,shear displacement and fracture of the hard phase particle,were observed on the boundary of the dead zone due to the large shear strains.

Two Lunar Mare Soil Simulants

Two new lunar mare soil simulants,NAO-2 and NAO-3,have been created in National Astronomical Observatories(NAO),Chinese Academy of Sciences.These two simulants were produced from low-titanium basalt and high-titanium basalt respectively.The chemical composition,mineralogy, particle size distribution,density,angle of internal friction,and cohesion of both simulants have been analyzed,indicating that some characteristics of NAO-2 and NAO-3 are similar to those of Apollo 14 and Apollo 11 landing site soils.NAO-2 and NAO-3 will be of great benefit to the scientific and engineering research on lunar soil.

SOLIDIFICATION OF Zn－Pb ALLOY UNDER SIMULANT MICROGRAVITY CONDITION OF ORTHOGONAL ELECTRIC AND MAGNETIC FIELDS

ＳＯＬＩＤＩＦＩＣＡＴＩＯＮＯＦＺｎ－ＰｂＡＬＬＯＹＵＮＤＥＲＳＩＭＵＬＡＮＴＭＩＣＲＯＧＲＡＶＩＴＹＣＯＮＤＩＴＩＯＮＯＦＯＲＴＨＯＧＯＮＡＬＥＬＥＣＴＲＩＣＡＮＤＭＡＧＮＥＴＩＣＦＩＥＬＤＳ￥Ｚｈａｏ，Ｊｉｕｚｈｏｕ；Ｇｕｏ，Ｊｉｎｇｊｉｅ；Ｊｉ...

Printability and hardening performance of three-dimensionally-printed geopolymer based on lunar regolith simulant for automated construction of lunar infrastructure

Using an in situ lunar regolith as a construction material in combination with 3D printing not only reduces the weight of materials carried from the Earth but also improves the automation of lunar infrastructure construction.This study aims to improve the printability of a geopolymer based on a BH-1 lunar regolith simulant,including the extrudability,open time,and buildability,by controlling the temperature and adding admixtures.Rheological parameters were used to represent printability with different water-to-binder ratios,printing temperatures,and contents of additives.The mechanical properties of the hardening geopolymer with different filling paths and loading directions were tested.The results show that heating the printed filaments with a water-to-binder ratio of 0.32 at 80°C can adjust the printability without adding any additive,which can reduce the construction cost of lunar infrastructure.The printability of the BH-1 geopolymer can also be improved by adding 0.3%Attagel-50 and 0.5%polypropylene fiber by mass at a temperature of 20℃to cope with the changeable environmental conditions on the Moon.After curing under a simulated lunar environment,the 72-h flexural and compressive strengths of the geopolymer specimens reach 4.1 and 48.1 MPa,respectively,which are promising considering that the acceleration of gravity on the Moon is 1/6 of that on the Earth.

3D-printed Lunar regolith simulant-based geopolymer composites with bio-inspired sandwich architectures

Over time,natural materials have evolved to be lightweight,high-strength,tough,and damage-tolerant due to their unique biological structures.Therefore,combining biological inspiration and structural design would provide traditional materials with a broader range of performance and applications.Here,the application of an ink-based three-dimensional(3D)printing strategy to the structural design of a Lunar regolith simulant-based geopolymer(HIT-LRS-1 GP)was first reported,and high-precision carbon fiber/quartz sand-reinforced biomimetic patterns inspired by the cellular sandwich structure of plant stems were fabricated.This study demonstrated how different cellular sandwich structures can balance the structure–property relationship and how to achieve unprecedented damage tolerance for a geopolymer composite.The results presented that components based on these biomimetic architectures exhibited stable non-catastrophic fracture characteristics regardless of the compression direction,and each structure possessed effective damage tolerance and anisotropy of mechanical properties.The results showed that the compressive strengths of honeycomb sandwich patterns,triangular sandwich patterns,wave sandwich patterns,and rectangular sandwich patterns in the Y-axis(Z-axis)direction were 15.6,17.9,11.3,and 20.1 MPa(46.7,26.5,23.8,and 34.4 MPa),respectively,and the maximum fracture strain corresponding to the above four structures could reach 10.2%,6.7%,5.8%,and 5.9%(12.1%,13.7%,13.6%,and 13.9%),respectively.

仿真技术在船舶舱室单元生产线设计中的应用

采用流水线模式生产船舶预制舱室单元正越来越受到关注,但目前针对其生产线设计方法的研究较少,为了改进流水生产线设计方案,提高生产力,本文开展仿真技术在舱室单元流水生产线设计不同阶段中的应用研究。首先在工序规划阶段运用遗传算法模块优化生产工序,其次在布局设计阶段基于仿真试验模块求解最佳库容,最后在方案比选阶段通过模拟复杂生产系统运行输出关键指标。研究结果表明,仿真技术在能为流水线工艺和布局设计提供有力支撑,对工程设计具有应用价值。

基于Plant Simulation的化纤自动落丝系统仿真实验分析

基于Plant Simulation软件,构建一种化纤自动落丝系统的3D数字化模型,对系统效率关键输入因子进行参数化设置,将系统各工位三维数字模型导入软件中建立层次化运动机构图形结构,并运用Simltalk语言实现三维动作仿真,通过基础物理参数设置,保证了仿真数字化模型与现实系统更具一致性。通过多级实验设计分析了系统影响因子对于系统效率的影响特性曲线,并进一步通过动态参数化实验方法,计算出双输入因子对系统效能影响的敏感度。该实验结果可为化纤自动落丝系统的建设成本控制与可行性分析提供指导,具有较好的工程应用价值。

基于四配流轴向柱塞马达的制动能回收方法

针对大惯性回转机构在制动时,动能都以热能的方式损失的问题,提出一种四配流轴向柱塞马达和蓄能器结合的制动能回收方法。不同体积、初始压力的蓄能器对惯性负载的回转制动能的回收和再利用的效果不同,为寻求较合理的蓄能器参数以达到较高的能量回收效果,手动调整仿真参数较为繁琐,提出采用基于多核CPU的快速并行优化方法用于蓄能器参数优化。首先,大惯性负载的驱动机构采用四配流轴向柱塞马达,其能量系统回收模型在Simulation X搭建,进而导出成具有CVODE求解加速的可执行程序,脱离仿真软件平台,在Windows操作系统独立运行;然后,利用导出的可执行程序与VC++进行二次开发,以微粒群算法解决特定工况下蓄能器选型的问题,充分利用多核CPU实现并行优化以提高仿真速度。仿真结果表明,在特定负载下得到优化后的蓄能器的参数,蓄能器回收并释放的能量占惯性动能的24.5%,回收油液全部得到释放。采用基于多核CPU的并行优化方法,仿真效率提高了10倍以上,该方法对系列化液压产品的快速开发具有一定的借鉴价值。

The Probability Density Function Related to Shallow Cumulus Entrainment Rate and Its Influencing Factors in a Large-Eddy Simulation

The process of entrainment-mixing between cumulus clouds and the ambient air is important for the development of cumulus clouds.Accurately obtaining the entrainment rate(λ)is particularly important for its parameterization within the overall cumulus parameterization scheme.In this study,an improved bulk-plume method is proposed by solving the equations of two conserved variables simultaneously to calculateλof cumulus clouds in a large-eddy simulation.The results demonstrate that the improved bulk-plume method is more reliable than the traditional bulk-plume method,becauseλ,as calculated from the improved method,falls within the range ofλvalues obtained from the traditional method using different conserved variables.The probability density functions ofλfor all data,different times,and different heights can be well-fitted by a log-normal distribution,which supports the assumed stochastic entrainment process in previous studies.Further analysis demonstrate that the relationship betweenλand the vertical velocity is better than other thermodynamic/dynamical properties;thus,the vertical velocity is recommended as the primary influencing factor for the parameterization ofλin the future.The results of this study enhance the theoretical understanding ofλand its influencing factors and shed new light on the development ofλparameterization.

基于Plant Simulation的压气机叶片型线加工产线分析与优化

运用专业仿真软件Plant Simulation,根据压气机叶片型线机械加工工艺特点和物料运行流程建立生产线仿真模型,从产能、设备利用率及产线瓶颈等多方面进行仿真分析与优化。结果表明:Plant Simulation仿真平台的仿真可以找出规划设计方案中存在的问题并验证方案的合理性。该仿真结果为型线机械加工产线的优化设计提供了可靠依据,达到了节约投资成本和缩短设计周期的目的。