In order to reduce the energy consumption and subsequent air pollution of coal-fired power station, based on the analysis to size and density distribution of particles from the recirculating load of the classifier of ...In order to reduce the energy consumption and subsequent air pollution of coal-fired power station, based on the analysis to size and density distribution of particles from the recirculating load of the classifier of pulverizer, the separation experiment on sampling material from power plant with a dilute phase fluidized bed to remove pyrite and other minerals and numerical simulation on the separation process were done. The results show that the minimum fluidization velocity is 1.62 cm/s. Pyrite and other minerals in the material are separated. Ash of the upper and bottom layer material account for 33.34% and 73.42% respectively and sulfur content occupy 1.12% and 8.96% respectively. Scanning electron microscopy and spectroscopy tests show that sulfur in the bottom material exist in the form of pyrite. Numerical simulation on the flow field form of the dilute phase separation bed with gas-solid two phase and particle motion verifies the experimental results.展开更多
The computer simulation of Al three-dimensional crystallite containing grain boundary of special type was carried out and its behaviour under high rate loading was investigated. The molecular dynamics method was used ...The computer simulation of Al three-dimensional crystallite containing grain boundary of special type was carried out and its behaviour under high rate loading was investigated. The molecular dynamics method was used and interaction betwen atoms was described based on pseudopotential method. Vortical character of the atom movements in the grain boundary region is realized under shear loading in certain directions. Back and forth movements of atoms in the direction which is perpendicular to the shear also arise. Amplitude of such movements is approximately equal to an interplanar distance in this direction.展开更多
This paper discussed the experimental results of the performance of an organic Rankine cycle(ORC)system with an ultra-low temperature heat source.The low boiling point working medium R134a was adopted in the system.Th...This paper discussed the experimental results of the performance of an organic Rankine cycle(ORC)system with an ultra-low temperature heat source.The low boiling point working medium R134a was adopted in the system.The simulated heat source temperature(SHST)in this work was set from 39.51°C to 48.60°C by the simulated heat source module.The influence of load percentage of simulated heat source(LPSHS)between 50%and 70%,the rotary valve opening(RVO)between 20%and 100%,the resistive load between 36Ωand 180Ωor the no-load of the generator,as well as the autumn and winter ambient temperature on the system performance were studied.The results showed that the stability of the system was promoted when the generator had a resistive load.The power generation(PG)and generator speed(GS)of the system in autumn were better than in winter,but the expander pressure ratio(EPR)was lower than in winter.Keep RVO unchanged,the SHST,the mass flow rate(MFR)of the working medium,GS,and the PG of the system increased with the increasing of LPSHS for different generator resistance load values.When the RVO was 60%,LPSHS was 70%,the SHST was 44.15°C and the resistive load was 72Ω,the highest PG reached 15.11 W.Finally,a simulation formula was obtained for LPSHS,resistance load,and PG,and its correlation coefficient was between 0.9818 and 0.9901.The formula can accurately predict the PG.The experimental results showed that the standard deviation between the experimental and simulated values was below 0.0792,and the relative error was within±5%.展开更多
Electric load simulator(ELS) systems are employed for electric power steering(EPS) test benches to load rack force by precise control. Precise ELS control is strongly influenced by nonlinear factors. When the steering...Electric load simulator(ELS) systems are employed for electric power steering(EPS) test benches to load rack force by precise control. Precise ELS control is strongly influenced by nonlinear factors. When the steering motor rapidly rotates, extra force is directly superimposed on the original static loading error, which becomes one of the main sources of the final error. It is key to achieve ELS precise loading control for the entire EPS test bench. Therefore, a three-part compound control algorithm is proposed to improve the loading accuracy. First, a fuzzy proportional–integral plus feedforward controller with force feedback is presented. Second, a friction compensation algorithm is established to reduce the influence of friction. Then, the relationships between each quantity and the extra force are analyzed when the steering motor rapidly rotates, and a net torque feedforward compensation algorithm is proposed to eliminate the extra force. The compound control algorithm was verified through simulations and experiments. The results show that the tracking performance of the compound control algorithm satisfies the demands of engineering practice, and the extra force in the ELS system can be suppressed by the net torque corresponding to the actuator’s acceleration.展开更多
Current high power load simulators are generally incapable of obtaining both high loading performance and high energy efficiency. Simulators with high energy efficiency are used to simulate static-state load, and thos...Current high power load simulators are generally incapable of obtaining both high loading performance and high energy efficiency. Simulators with high energy efficiency are used to simulate static-state load, and those with high dynamic performance typically have low energy efficiency. In this paper, the variants of secondary control(VSC) with power recovery are developed to solve this problem for loading hydraulic driving devices that operate under variable pressure, unlike classical secondary control(CSC) that operates in constant pressure network. Hydrostatic secondary control units are used as the loading components, by which the absorbed mechanical power from the tested device is converted into hydraulic power and then fed back into the tested system through 4 types of feedback passages(FPs). The loading subsystem can operate in constant pressure network, controlled variable pressure network, or the same variable pressure network as that of the tested device by using different FPs. The 4 types of systems are defined, and their key techniques are analyzed, including work principle, simulating the work state of original tested device, static operation points, loading performance, energy efficiency, and control strategy, etc. The important technical merits of the 4 schemes are compared, and 3 of the schemes are selected, designed, simulated using AMESim and evaluated. The researching results show that the investigated systems can simulate the given loads effectively, realize the work conditions of the tested device, and furthermore attain a high power recovery efficiency that ranges from 0.54 to 0.85, even though the 3 schemes have different loading performances and energy efficiencies. This paper proposes several loading schemes that can achieve both high dynamic performance and high power recovery efficiency.展开更多
A two-dimensional, three-temperature radiation magneto-hydrodynamics model is applied to the investigation of evolutional trends in x-ray radiation power, energy, peak plasma temperature and density as functions of dr...A two-dimensional, three-temperature radiation magneto-hydrodynamics model is applied to the investigation of evolutional trends in x-ray radiation power, energy, peak plasma temperature and density as functions of drive current rise-time and initial load density distribution by using the typical experimental parameters of tungsten wire-array Z- pinch on the Qiangguang-I generator. The numerical results show that as the drive current rise-time is shortened, x-ray radiation peak power, energy, peak plasma density and peak ion temperature increase approximately linearly, but among them the x-ray radiation peak power increases more quickly. As the initial plasma density distribution in the radial direction becomes gradually flattened, the peak radiation power and the peak ion-temperature almost exponentially increase, while the radiation energy and the peak plasma density change only a little. The main effect of shortening drive current rise-time is to enhance compression of plasma, and the effect of flattening initial load density distribution in the radial direction is to raise the plasma temperature. Both of the approaches elevate the x-ray peak radiation power展开更多
Each joint of hydraulic drive quadruped robot is driven by the hydraulic drive unit(HDU), and the contacting between the robot foot end and the ground is complex and variable, which increases the difficulty of force...Each joint of hydraulic drive quadruped robot is driven by the hydraulic drive unit(HDU), and the contacting between the robot foot end and the ground is complex and variable, which increases the difficulty of force control inevitably. In the recent years, although many scholars researched some control methods such as disturbance rejection control, parameter self-adaptive control, impedance control and so on, to improve the force control performance of HDU, the robustness of the force control still needs improving. Therefore, how to simulate the complex and variable load characteristics of the environment structure and how to ensure HDU having excellent force control performance with the complex and variable load characteristics are key issues to be solved in this paper. The force control system mathematic model of HDU is established by the mechanism modeling method, and the theoretical models of a novel force control compensation method and a load characteristics simulation method under different environment structures are derived, considering the dynamic characteristics of the load stiffness and the load damping under different environment structures. Then, simulation effects of the variable load stiffness and load damping under the step and sinusoidal load force are analyzed experimentally on the HDU force control performance test platform, which provides the foundation for the force control compensation experiment research. In addition, the optimized PID control parameters are designed to make the HDU have better force control performance with suitable load stiffness and load damping, under which the force control compensation method is introduced, and the robustness of the force control system with several constant load characteristics and the variable load characteristics respectively are comparatively analyzed by experiment. The research results indicate that if the load characteristics are known, the force control compensation method presented in this paper has positive compensation effects on the load characteristics variation, i.e., this method decreases the effects of the load characteristics variation on the force control performance and enhances the force control system robustness with the constant PID parameters, thereby, the online PID parameters tuning control method which is complex needs not be adopted. All the above research provides theoretical and experimental foundation for the force control method of the quadruped robot joints with high robustness.展开更多
Based on the analyses of the structural feature and the function requirements of newstyle bottle cap, the two fundamental components, the lining washer and the outer body, are abstracted as a plate and a cylinder with...Based on the analyses of the structural feature and the function requirements of newstyle bottle cap, the two fundamental components, the lining washer and the outer body, are abstracted as a plate and a cylinder with thin wall respectively. For simulating the deformation of the lining washer under equiaxial pressure, the modified Lagrangian finite element analysis is applied on the 228 triangular elements. Under assembly pressure, the plastoelastic deformation of both the lining washer and the outer body are studied in terms of Tresca's yield criterion and the limitation of the plastic deformation is presented when the two components are assembled into one unit. For the production of this kind of bottle cover, experiments are carried out by carefully measuring the changes of the diameter of lining washer as well as that of the outer body. It is shown that results from the experiments have a good agreement with the theoretical calculation and the maximum value of the allowable pressure has successfully been used in the design of newly developed bottle cap production system.展开更多
In order to obtain a deeper understanding of the behavior of the structure under high wind load,this paper conducted an experimental study on a full-scale L-shaped single story light frame wood house under the uniform...In order to obtain a deeper understanding of the behavior of the structure under high wind load,this paper conducted an experimental study on a full-scale L-shaped single story light frame wood house under the uniform lateral load simulated using a gasbag.The investigation involved the performance of light frame wood structure after it experienced the repeated cyclic lateral wind load as well as the performance of the structure under the ultimate lateral load.Then,the study verified that light frame wood structure can resist repeated cyclic wind loads without observable degradation in stiffness during the anticipated serve life,and recommended shear wall percent drift restriction for lateral wind load design of wood structure in serviceability limit states is 1/400 drift,and in ultimate limit states is 1/80 drift.The conclusions of this paper can be benefit for the engineering practice of the light frame wood structures in high wind load regions.展开更多
In this paper,a numerical code,RFPA2D(rock failure process analysis),was used to simulate the initiation and propagation of fractures around a pre-existing single cavity and multiple cavities in brittle rocks.Both s...In this paper,a numerical code,RFPA2D(rock failure process analysis),was used to simulate the initiation and propagation of fractures around a pre-existing single cavity and multiple cavities in brittle rocks.Both static and dynamic loads were applied to the rock specimens to investigate the mechanism of fracture evolution around the cavities for different lateral pressure coefficients.In addition,characteristics of acoustic emission(AE) associated with fracture evolution were simulated.Finally,the evolution and interaction of fractures between multiple cavities were investigated with consideration of stress redistribution and transference in compressive and tensile stress fields.The numerically simulated results reproduced primary tensile,remote,and shear crack fractures,which are in agreement with the experimental results.Moreover,numerical results suggested that both compressive and tensile waves could influence the propagation of tensile cracks;in particular,the reflected tensile wave accelerated the propagation of tensile cracks.展开更多
The stress-induced magnetic domain switching in FeGa thin films is studied using phase-field method. In particular, the magnetic field is applied along the [110] direction and biaxial stresses are applied along [ 100]...The stress-induced magnetic domain switching in FeGa thin films is studied using phase-field method. In particular, the magnetic field is applied along the [110] direction and biaxial stresses are applied along [ 100] and [010]. A compressive pre-stress corresponds to a smaller coercive magnetic field while a tensile pre-stress corresponded to a larger coercive field. At the same time, it is also found that the transition between butterfly and square-like magnetostriction loops occurs at the critical opposite biaxial stress state. The two different evolutions correspond to two different mechanisms: one is that the single domain swings across a fan area back and forth; the other is that the single domain turns a clockwise circle. The results can be explained bv the stress tuned anisotronv energy well.展开更多
This paper presents a new measuring method based on the simulating technology and measuring technology, researches and analyzes deeply its network performance evaluating model, measuring methods, evaluating algorithms...This paper presents a new measuring method based on the simulating technology and measuring technology, researches and analyzes deeply its network performance evaluating model, measuring methods, evaluating algorithms and system implementation. Experimental results argue that this method can define expediently different models of manual simulated loads and configure neatly different environments of network applications, can develop adequately characteristics of widespread applications and accuracy in simulating technology, as well as reality, reliability and better adaptability in measuring technology.展开更多
This paper introduced a performance evaluating approach of computer communication system based on the simulation and measurement technology, and discussed its evaluating models. The result of our experiment showed tha...This paper introduced a performance evaluating approach of computer communication system based on the simulation and measurement technology, and discussed its evaluating models. The result of our experiment showed that the outcome of practical measurement on Ether-LAN fitted in well with the theoretical analysis. The approach we presented can be used to define various kinds of artificially simulated load models conveiently, build all kinds of network application environments in a flexible way, and exert sufficiently the widely-used and high-precision features of the traditional simulation technology and the reality, reliability, adaptability features of measurement technology.展开更多
Directing to the strong position coupling problem of electro-hydraulic load simulator (EHLS), this article presents an adaptive nonlinear optimal compensation control strategy based on two estimated nonlinear paramete...Directing to the strong position coupling problem of electro-hydraulic load simulator (EHLS), this article presents an adaptive nonlinear optimal compensation control strategy based on two estimated nonlinear parameters, viz. the flow gain coefficient of servo valve and total factors of flow-pressure coefficient. Taking trace error of torque control system to zero as control object, this article designs the adaptive nonlinear optimal compensation control strategy, which regards torque control output of closed-loop controller converging to zero as the control target, to optimize torque tracking performance. Electro-hydraulic load simulator is a typical case of the torque system which is strongly coupled with a hydraulic positioning system. This article firstly builds and analyzes the mathematical models of hydraulic torque and positioning system, then designs an adaptive nonlinear optimal compensation controller, proves the validity of parameters estimation, and shows the comparison data among three control structures with various typical operating conditions, including proportion-integral-derivative (PID) controller only, the velocity synchronizing controller plus P1D controller and the proposed adaptive nonlinear optimal compensation controller plus PID controller. Experimental results show that systems' nonlinear parameters are estimated exactly using the proposed method, and the trace accuracy of the torque system is greatly enhanced by adaptive nonlinear optimal compensation control, and the torque servo system capability against sudden disturbance can be greatly improved.展开更多
This paper deals with the high performance force control of hydraulic load simulator. Many previous works for hydraulic force control are based on their linearization equations, but hydraulic inherent nonlinear proper...This paper deals with the high performance force control of hydraulic load simulator. Many previous works for hydraulic force control are based on their linearization equations, but hydraulic inherent nonlinear properties and uncertainties make the conven- tional feedback proportional-integral-derivative control not yield to high-performance requirements. In this paper, a nonlinear system model is derived and linear parameterization is made for adaptive control. Then a discontinuous projection-based nonlin- ear adaptive robust force controller is developed for hydraulic load simulator. The proposed controller constructs an asymptoti- cally stable adaptive controller and adaptation laws, which can compensate for the system nonlinearities and uncertain parame- ters. Meanwhile a well-designed robust controller is also developed to cope with the hydraulic system uncertain nonlinearities. The controller achieves a guaranteed transient performance and final tracking accuracy in the presence of both parametric uncer- tainties and uncertain nonlinearities; in the absence of uncertain nonlinearities, the scheme also achieves asymptotic tracking performance. Simulation and experiment comparative results are obtained to verify the high-performance nature of the proposed control strategy and the tracking accuracy is greatly improved.展开更多
This article, in order to precisely impose friction on aircraft and weapon actuation systems, presents a new friction loading method characteristic of "torque-zero velocity" switching control with an electro-hydraul...This article, in order to precisely impose friction on aircraft and weapon actuation systems, presents a new friction loading method characteristic of "torque-zero velocity" switching control with an electro-hydraulic load simulator. As the general Stribeck friction model has little related to static friction, it proposes a "torque-zero velocity" switcher, in which a zero-velocity controller is developed to load the static friction and a torque controller the kinetic friction. With the help of mathematical modeling, this article designs a "torque-zero velocity" switching controller and, correspondingly, provides a "dual-threshold judgment" algorithm. Simulation results indicate that the proposed method can be successfully used to carry out the static and kinetic friction simulation with an electro-hydraulic load simulator.展开更多
This paper studies a nonlinear robust control algorithm of the electro-hydraulic load simulator (EHLS). The tracking performance of the EHLS is mainly limited by the actuator's motion disturbance, flow nonlinearity...This paper studies a nonlinear robust control algorithm of the electro-hydraulic load simulator (EHLS). The tracking performance of the EHLS is mainly limited by the actuator's motion disturbance, flow nonlinearity, and friction, etc. The developed controller is developed based on the nonlinear motion loading model. The problems of the actuator's disturbance and flow nonlinearity are considered. To address the friction problem, the friction model of the loading motor is identified experimentally. The friction disturbance is compensated using the obtained friction model. Therefore, this paper considers the main three factors comprehensively. The developed algorithm is easy to apply since the controller can be obtained just with one step back-stepping design. The stability of the developed algorithm is proven via Lyapunov analysis. Both co-simulation and experiments are performed to verify the effectiveness of this method.展开更多
This paper investigates motion coupling disturbance(the so called surplus torque)in the hardware-in-the-loop(HIL)experiments.The''velocity synchronization scheme''was proposed by Jiao for an electro-hydraulic ...This paper investigates motion coupling disturbance(the so called surplus torque)in the hardware-in-the-loop(HIL)experiments.The''velocity synchronization scheme''was proposed by Jiao for an electro-hydraulic load simulator(EHLS)in 2004.In some situations,however,the scheme is limited in the implementation for certain reasons,as is the case when the actuator's valve signal is not available or it is seriously polluted by noise.To solve these problems,a''dual-loop scheme''is developed for EHLS.The dual-loop scheme is a combination of a torque loop and a position synchronization loop.The role of the position synchronization loop is to decouple the motion disturbance caused by the actuator system.To verify the feasibility and effectiveness of the proposed scheme,extensive simulations are performed using AMESim.Then,the performance of the developed method is validated by experiments.展开更多
基金supported financially by the National Natural Science Foundation of China (Nos. 51074156 and 50921002)
文摘In order to reduce the energy consumption and subsequent air pollution of coal-fired power station, based on the analysis to size and density distribution of particles from the recirculating load of the classifier of pulverizer, the separation experiment on sampling material from power plant with a dilute phase fluidized bed to remove pyrite and other minerals and numerical simulation on the separation process were done. The results show that the minimum fluidization velocity is 1.62 cm/s. Pyrite and other minerals in the material are separated. Ash of the upper and bottom layer material account for 33.34% and 73.42% respectively and sulfur content occupy 1.12% and 8.96% respectively. Scanning electron microscopy and spectroscopy tests show that sulfur in the bottom material exist in the form of pyrite. Numerical simulation on the flow field form of the dilute phase separation bed with gas-solid two phase and particle motion verifies the experimental results.
文摘The computer simulation of Al three-dimensional crystallite containing grain boundary of special type was carried out and its behaviour under high rate loading was investigated. The molecular dynamics method was used and interaction betwen atoms was described based on pseudopotential method. Vortical character of the atom movements in the grain boundary region is realized under shear loading in certain directions. Back and forth movements of atoms in the direction which is perpendicular to the shear also arise. Amplitude of such movements is approximately equal to an interplanar distance in this direction.
基金This work was supported by Tianjin Natural Science Foundation(No.21JCZDJC00750).
文摘This paper discussed the experimental results of the performance of an organic Rankine cycle(ORC)system with an ultra-low temperature heat source.The low boiling point working medium R134a was adopted in the system.The simulated heat source temperature(SHST)in this work was set from 39.51°C to 48.60°C by the simulated heat source module.The influence of load percentage of simulated heat source(LPSHS)between 50%and 70%,the rotary valve opening(RVO)between 20%and 100%,the resistive load between 36Ωand 180Ωor the no-load of the generator,as well as the autumn and winter ambient temperature on the system performance were studied.The results showed that the stability of the system was promoted when the generator had a resistive load.The power generation(PG)and generator speed(GS)of the system in autumn were better than in winter,but the expander pressure ratio(EPR)was lower than in winter.Keep RVO unchanged,the SHST,the mass flow rate(MFR)of the working medium,GS,and the PG of the system increased with the increasing of LPSHS for different generator resistance load values.When the RVO was 60%,LPSHS was 70%,the SHST was 44.15°C and the resistive load was 72Ω,the highest PG reached 15.11 W.Finally,a simulation formula was obtained for LPSHS,resistance load,and PG,and its correlation coefficient was between 0.9818 and 0.9901.The formula can accurately predict the PG.The experimental results showed that the standard deviation between the experimental and simulated values was below 0.0792,and the relative error was within±5%.
基金Supported by National Natural Science Foundation of China (Grant No. 51505178)China Postdoctoral Science Foundation (Grant No. 2014M561289)。
文摘Electric load simulator(ELS) systems are employed for electric power steering(EPS) test benches to load rack force by precise control. Precise ELS control is strongly influenced by nonlinear factors. When the steering motor rapidly rotates, extra force is directly superimposed on the original static loading error, which becomes one of the main sources of the final error. It is key to achieve ELS precise loading control for the entire EPS test bench. Therefore, a three-part compound control algorithm is proposed to improve the loading accuracy. First, a fuzzy proportional–integral plus feedforward controller with force feedback is presented. Second, a friction compensation algorithm is established to reduce the influence of friction. Then, the relationships between each quantity and the extra force are analyzed when the steering motor rapidly rotates, and a net torque feedforward compensation algorithm is proposed to eliminate the extra force. The compound control algorithm was verified through simulations and experiments. The results show that the tracking performance of the compound control algorithm satisfies the demands of engineering practice, and the extra force in the ELS system can be suppressed by the net torque corresponding to the actuator’s acceleration.
文摘Current high power load simulators are generally incapable of obtaining both high loading performance and high energy efficiency. Simulators with high energy efficiency are used to simulate static-state load, and those with high dynamic performance typically have low energy efficiency. In this paper, the variants of secondary control(VSC) with power recovery are developed to solve this problem for loading hydraulic driving devices that operate under variable pressure, unlike classical secondary control(CSC) that operates in constant pressure network. Hydrostatic secondary control units are used as the loading components, by which the absorbed mechanical power from the tested device is converted into hydraulic power and then fed back into the tested system through 4 types of feedback passages(FPs). The loading subsystem can operate in constant pressure network, controlled variable pressure network, or the same variable pressure network as that of the tested device by using different FPs. The 4 types of systems are defined, and their key techniques are analyzed, including work principle, simulating the work state of original tested device, static operation points, loading performance, energy efficiency, and control strategy, etc. The important technical merits of the 4 schemes are compared, and 3 of the schemes are selected, designed, simulated using AMESim and evaluated. The researching results show that the investigated systems can simulate the given loads effectively, realize the work conditions of the tested device, and furthermore attain a high power recovery efficiency that ranges from 0.54 to 0.85, even though the 3 schemes have different loading performances and energy efficiencies. This paper proposes several loading schemes that can achieve both high dynamic performance and high power recovery efficiency.
基金Project supported by the National Natural Science Foundation of China (Grant No 10035020).
文摘A two-dimensional, three-temperature radiation magneto-hydrodynamics model is applied to the investigation of evolutional trends in x-ray radiation power, energy, peak plasma temperature and density as functions of drive current rise-time and initial load density distribution by using the typical experimental parameters of tungsten wire-array Z- pinch on the Qiangguang-I generator. The numerical results show that as the drive current rise-time is shortened, x-ray radiation peak power, energy, peak plasma density and peak ion temperature increase approximately linearly, but among them the x-ray radiation peak power increases more quickly. As the initial plasma density distribution in the radial direction becomes gradually flattened, the peak radiation power and the peak ion-temperature almost exponentially increase, while the radiation energy and the peak plasma density change only a little. The main effect of shortening drive current rise-time is to enhance compression of plasma, and the effect of flattening initial load density distribution in the radial direction is to raise the plasma temperature. Both of the approaches elevate the x-ray peak radiation power
基金Supported by National Key Basic Research Program of China(973 Program,Grant No.2014CB046405)State Key Laboratory of Fluid Power and Mechatronic Systems(Zhejiang University)Open Fund Project(Grant No.GZKF-201502)Hebei Military and Civilian Industry Development Funds Projects of China(Grant No.2015B060)
文摘Each joint of hydraulic drive quadruped robot is driven by the hydraulic drive unit(HDU), and the contacting between the robot foot end and the ground is complex and variable, which increases the difficulty of force control inevitably. In the recent years, although many scholars researched some control methods such as disturbance rejection control, parameter self-adaptive control, impedance control and so on, to improve the force control performance of HDU, the robustness of the force control still needs improving. Therefore, how to simulate the complex and variable load characteristics of the environment structure and how to ensure HDU having excellent force control performance with the complex and variable load characteristics are key issues to be solved in this paper. The force control system mathematic model of HDU is established by the mechanism modeling method, and the theoretical models of a novel force control compensation method and a load characteristics simulation method under different environment structures are derived, considering the dynamic characteristics of the load stiffness and the load damping under different environment structures. Then, simulation effects of the variable load stiffness and load damping under the step and sinusoidal load force are analyzed experimentally on the HDU force control performance test platform, which provides the foundation for the force control compensation experiment research. In addition, the optimized PID control parameters are designed to make the HDU have better force control performance with suitable load stiffness and load damping, under which the force control compensation method is introduced, and the robustness of the force control system with several constant load characteristics and the variable load characteristics respectively are comparatively analyzed by experiment. The research results indicate that if the load characteristics are known, the force control compensation method presented in this paper has positive compensation effects on the load characteristics variation, i.e., this method decreases the effects of the load characteristics variation on the force control performance and enhances the force control system robustness with the constant PID parameters, thereby, the online PID parameters tuning control method which is complex needs not be adopted. All the above research provides theoretical and experimental foundation for the force control method of the quadruped robot joints with high robustness.
基金This project is supported by Provincial Natural Science Fundation of Hei-longjiang, China (No.E0311) and Provincial Key Project of Heilingjiang,China (No.G99A13-1).
文摘Based on the analyses of the structural feature and the function requirements of newstyle bottle cap, the two fundamental components, the lining washer and the outer body, are abstracted as a plate and a cylinder with thin wall respectively. For simulating the deformation of the lining washer under equiaxial pressure, the modified Lagrangian finite element analysis is applied on the 228 triangular elements. Under assembly pressure, the plastoelastic deformation of both the lining washer and the outer body are studied in terms of Tresca's yield criterion and the limitation of the plastic deformation is presented when the two components are assembled into one unit. For the production of this kind of bottle cover, experiments are carried out by carefully measuring the changes of the diameter of lining washer as well as that of the outer body. It is shown that results from the experiments have a good agreement with the theoretical calculation and the maximum value of the allowable pressure has successfully been used in the design of newly developed bottle cap production system.
基金Sponsored by the National Natural Science Foundation of China(Grant No. 50508012)
文摘In order to obtain a deeper understanding of the behavior of the structure under high wind load,this paper conducted an experimental study on a full-scale L-shaped single story light frame wood house under the uniform lateral load simulated using a gasbag.The investigation involved the performance of light frame wood structure after it experienced the repeated cyclic lateral wind load as well as the performance of the structure under the ultimate lateral load.Then,the study verified that light frame wood structure can resist repeated cyclic wind loads without observable degradation in stiffness during the anticipated serve life,and recommended shear wall percent drift restriction for lateral wind load design of wood structure in serviceability limit states is 1/400 drift,and in ultimate limit states is 1/80 drift.The conclusions of this paper can be benefit for the engineering practice of the light frame wood structures in high wind load regions.
基金granted by the National Science Foundation (NSF) under Grant CMMI-0408390 and NSF CAREER Award CMMI-0644552the American Chemical Society Petroleum Research Foundation under Grant PRF-44468-G9+3 种基金National Natural Science Foundation of China under Grant No.51050110143granted by Huoyingdong Educational Foundation under Grant No.114024Jiangsu Natural Science Foundation under Grant No.SBK200910046granted by Jiangsu Postdoctoral Foundation under Grant No.0901005C
文摘In this paper,a numerical code,RFPA2D(rock failure process analysis),was used to simulate the initiation and propagation of fractures around a pre-existing single cavity and multiple cavities in brittle rocks.Both static and dynamic loads were applied to the rock specimens to investigate the mechanism of fracture evolution around the cavities for different lateral pressure coefficients.In addition,characteristics of acoustic emission(AE) associated with fracture evolution were simulated.Finally,the evolution and interaction of fractures between multiple cavities were investigated with consideration of stress redistribution and transference in compressive and tensile stress fields.The numerically simulated results reproduced primary tensile,remote,and shear crack fractures,which are in agreement with the experimental results.Moreover,numerical results suggested that both compressive and tensile waves could influence the propagation of tensile cracks;in particular,the reflected tensile wave accelerated the propagation of tensile cracks.
基金supported by the National Natural Science Foundation of China(11090331,11522214,11521202,11227801)the Beijing NOVA Program(Z151100000315041)the key subject ‘‘Computational Solid Mechanics’’ of China Academy of Engineering Physics
文摘The stress-induced magnetic domain switching in FeGa thin films is studied using phase-field method. In particular, the magnetic field is applied along the [110] direction and biaxial stresses are applied along [ 100] and [010]. A compressive pre-stress corresponds to a smaller coercive magnetic field while a tensile pre-stress corresponded to a larger coercive field. At the same time, it is also found that the transition between butterfly and square-like magnetostriction loops occurs at the critical opposite biaxial stress state. The two different evolutions correspond to two different mechanisms: one is that the single domain swings across a fan area back and forth; the other is that the single domain turns a clockwise circle. The results can be explained bv the stress tuned anisotronv energy well.
文摘This paper presents a new measuring method based on the simulating technology and measuring technology, researches and analyzes deeply its network performance evaluating model, measuring methods, evaluating algorithms and system implementation. Experimental results argue that this method can define expediently different models of manual simulated loads and configure neatly different environments of network applications, can develop adequately characteristics of widespread applications and accuracy in simulating technology, as well as reality, reliability and better adaptability in measuring technology.
基金Supported by the National 863 High-Tech Project of China!(863-30 0-02-09-99) by Key Research Project ofHubei Province!(99
文摘This paper introduced a performance evaluating approach of computer communication system based on the simulation and measurement technology, and discussed its evaluating models. The result of our experiment showed that the outcome of practical measurement on Ether-LAN fitted in well with the theoretical analysis. The approach we presented can be used to define various kinds of artificially simulated load models conveiently, build all kinds of network application environments in a flexible way, and exert sufficiently the widely-used and high-precision features of the traditional simulation technology and the reality, reliability, adaptability features of measurement technology.
基金National Natural Science Foundation of China (50825502)
文摘Directing to the strong position coupling problem of electro-hydraulic load simulator (EHLS), this article presents an adaptive nonlinear optimal compensation control strategy based on two estimated nonlinear parameters, viz. the flow gain coefficient of servo valve and total factors of flow-pressure coefficient. Taking trace error of torque control system to zero as control object, this article designs the adaptive nonlinear optimal compensation control strategy, which regards torque control output of closed-loop controller converging to zero as the control target, to optimize torque tracking performance. Electro-hydraulic load simulator is a typical case of the torque system which is strongly coupled with a hydraulic positioning system. This article firstly builds and analyzes the mathematical models of hydraulic torque and positioning system, then designs an adaptive nonlinear optimal compensation controller, proves the validity of parameters estimation, and shows the comparison data among three control structures with various typical operating conditions, including proportion-integral-derivative (PID) controller only, the velocity synchronizing controller plus P1D controller and the proposed adaptive nonlinear optimal compensation controller plus PID controller. Experimental results show that systems' nonlinear parameters are estimated exactly using the proposed method, and the trace accuracy of the torque system is greatly enhanced by adaptive nonlinear optimal compensation control, and the torque servo system capability against sudden disturbance can be greatly improved.
基金National Natural Science Foundation for Distinguished Young Scholars of China (50825502)
文摘This paper deals with the high performance force control of hydraulic load simulator. Many previous works for hydraulic force control are based on their linearization equations, but hydraulic inherent nonlinear properties and uncertainties make the conven- tional feedback proportional-integral-derivative control not yield to high-performance requirements. In this paper, a nonlinear system model is derived and linear parameterization is made for adaptive control. Then a discontinuous projection-based nonlin- ear adaptive robust force controller is developed for hydraulic load simulator. The proposed controller constructs an asymptoti- cally stable adaptive controller and adaptation laws, which can compensate for the system nonlinearities and uncertain parame- ters. Meanwhile a well-designed robust controller is also developed to cope with the hydraulic system uncertain nonlinearities. The controller achieves a guaranteed transient performance and final tracking accuracy in the presence of both parametric uncer- tainties and uncertain nonlinearities; in the absence of uncertain nonlinearities, the scheme also achieves asymptotic tracking performance. Simulation and experiment comparative results are obtained to verify the high-performance nature of the proposed control strategy and the tracking accuracy is greatly improved.
基金National Natural Science Foundation of China (50825502)
文摘This article, in order to precisely impose friction on aircraft and weapon actuation systems, presents a new friction loading method characteristic of "torque-zero velocity" switching control with an electro-hydraulic load simulator. As the general Stribeck friction model has little related to static friction, it proposes a "torque-zero velocity" switcher, in which a zero-velocity controller is developed to load the static friction and a torque controller the kinetic friction. With the help of mathematical modeling, this article designs a "torque-zero velocity" switching controller and, correspondingly, provides a "dual-threshold judgment" algorithm. Simulation results indicate that the proposed method can be successfully used to carry out the static and kinetic friction simulation with an electro-hydraulic load simulator.
基金supported by the National Key Basic Research Program of China (No. 2014CB046406)the Key Projects of the National Natural Science Foundation of China (No. 51235002)
文摘This paper studies a nonlinear robust control algorithm of the electro-hydraulic load simulator (EHLS). The tracking performance of the EHLS is mainly limited by the actuator's motion disturbance, flow nonlinearity, and friction, etc. The developed controller is developed based on the nonlinear motion loading model. The problems of the actuator's disturbance and flow nonlinearity are considered. To address the friction problem, the friction model of the loading motor is identified experimentally. The friction disturbance is compensated using the obtained friction model. Therefore, this paper considers the main three factors comprehensively. The developed algorithm is easy to apply since the controller can be obtained just with one step back-stepping design. The stability of the developed algorithm is proven via Lyapunov analysis. Both co-simulation and experiments are performed to verify the effectiveness of this method.
基金sponsored by the National Basic Research Program of China (No.2014CB046406)the Key Projects of the National Natural Science Foundation (No.51235002)
文摘This paper investigates motion coupling disturbance(the so called surplus torque)in the hardware-in-the-loop(HIL)experiments.The''velocity synchronization scheme''was proposed by Jiao for an electro-hydraulic load simulator(EHLS)in 2004.In some situations,however,the scheme is limited in the implementation for certain reasons,as is the case when the actuator's valve signal is not available or it is seriously polluted by noise.To solve these problems,a''dual-loop scheme''is developed for EHLS.The dual-loop scheme is a combination of a torque loop and a position synchronization loop.The role of the position synchronization loop is to decouple the motion disturbance caused by the actuator system.To verify the feasibility and effectiveness of the proposed scheme,extensive simulations are performed using AMESim.Then,the performance of the developed method is validated by experiments.