Target detection is one of the key technology of precision chemical application.Previously the digital coding modulation technique was commonly used to emit and receive the optical signal in the target detection syste...Target detection is one of the key technology of precision chemical application.Previously the digital coding modulation technique was commonly used to emit and receive the optical signal in the target detection systems previously in China.It was difficult to adjust the output power,and the anti-interference ability was weak in these systems.In order to resolve these problems,the target detection method based on analog sine-wave modulation was studied.The spectral detecting system was set up in the aspects of working principle,electric circuit,and optical path.Lab testing was performed.The results showed that the reflected signal from the target varied inversely with detection distances.It indicated that it was feasible to establish the target detection system using analog sine-wave modulation technology.Furthermore,quantitative measurement of the reflected optical signal for near-infrared and visible light could be achieved by using this system.The research laid the foundation for the future development of the corresponding instrument.展开更多
A new procedure of trial variational wave functional is proposed for invostigating the mass reuormalizationand the local structure of the ground state of a one-dimensional quantum sine-Gorrdonm model with linear spati...A new procedure of trial variational wave functional is proposed for invostigating the mass reuormalizationand the local structure of the ground state of a one-dimensional quantum sine-Gorrdonm model with linear spatial modu-lation, whose ground state differs from that without modulation. Thc phase diagram obtained in parameters (αA 2,β2)plane shows that the vertical part of the boundary between soliton lattice phase and iucommensurate (IC) phase withvanishing gap sticks at β2 = 4, the IC phase can only appear forβ2 ＞ 47r and thc IC phase regime is enlarged withincreasing spatial modulation in the case of definite parameter αA-2. The transition is of the continuous type on thevertical part of the boundary, while it is of the first order on the boundary forβ2 ＞ 47r.展开更多
为探究全光纤电流互感器(fiber optical current transformer,FOCT)调制回路故障对探测器输出信号影响,便于故障预测与故障诊断,文中首先建立包含光电回路相位延迟的正弦波调制FOCT输出信号数学模型,给出调制深度与驱动电压、二次谐波...为探究全光纤电流互感器(fiber optical current transformer,FOCT)调制回路故障对探测器输出信号影响,便于故障预测与故障诊断,文中首先建立包含光电回路相位延迟的正弦波调制FOCT输出信号数学模型,给出调制深度与驱动电压、二次谐波、四次谐波的数学关系式,分析定目标值调制器闭环调制、解调的基本方法。在此基础上通过建立数学模型分析调制深度对探测器输出光强峰值、平均光强、二次谐波、四次谐波的影响。据此提出发生调制回路故障时调制深度降低是导致探测器输出信号异常的关键因素,探测器输出平均光强增大、四次谐波降低、二次/四次谐波比值增加应作为调制回路故障的典型特征。最后开展实际FOCT模拟试验证明理论研究的有效性。展开更多
正弦波调制全光纤电流互感器(fiber optical current transformer,FOCT)因具备动态范围大、不与一次主回路连接、绝缘性能好、无铁磁饱和等优点,成为特高压换流站重要的测量设备。但在实际运行过程中,FOCT故障率远高于电磁互感器,而光...正弦波调制全光纤电流互感器(fiber optical current transformer,FOCT)因具备动态范围大、不与一次主回路连接、绝缘性能好、无铁磁饱和等优点,成为特高压换流站重要的测量设备。但在实际运行过程中,FOCT故障率远高于电磁互感器,而光回路故障是最为常见的故障类型。针对此,首先建立FOCT数学模型,提出二次谐波、光强峰值、平均光强应作为重要监测量;在此基础上分析光回路故障对探测器输出信号的影响,提出基于驱动电流及探测器输出信号变化的光回路故障预警方法,通过阈值设置及平均光强趋势判断等辨识真实的光回路故障。最后开展现场试验验证,证明该预警方法的有效性。展开更多
A large amount of switching loss occurs in the inverter. From this point of view, an inverter design should be optimized for which size and cost will be minimum along with increasing efficiency. The main aim of this p...A large amount of switching loss occurs in the inverter. From this point of view, an inverter design should be optimized for which size and cost will be minimum along with increasing efficiency. The main aim of this paper is the analysis and development of single-phase and three-phase inverter to design with MOSFET and IGBT as power elements by sinusoidal pulse width modulation (SPWM) technique using MATLAB Simulink software and compare their difference with the practical inverter. This work proposes different multilevel stages for the cascaded H-Bridge inverter to enhance the output voltages. Then compare their performance, harmonic distortion, and frequency spectrum. The hardware of an inverter circuit has been developed using the SG3524 microcontroller. The main goal of this design is to generate a sine wave with fewer harmonics, while keeping the cost and complexity of the circuit low. The designed inverter has undergone testing with different AC loads and is primarily intended for low-power applications, as lamps, fans, and chargers. This design aims to provide a reliable and efficient inverter solution for these specific applications.展开更多
Pulse-width modulation(PWM)sprays can improve flow accuracy by adjusting duty cycle and frequency signal which accurately controls the relative proportion of opening time of solenoid valve.The objective of this resear...Pulse-width modulation(PWM)sprays can improve flow accuracy by adjusting duty cycle and frequency signal which accurately controls the relative proportion of opening time of solenoid valve.The objective of this research was to determine the impacts of PWM duty cycle and frequency on spray drift characteristic.Spray tests were conducted in a wind tunnel with a PWM variable-rate spraying system.The airborne drift and sediment drift were determined with tracer method,and the drift potential reduction(DPR)compared with reference condition of 100%duty cycle at vertical profile and horizontal planes were calculated,respectively.The results show that,at a given frequency,droplet size decreases with the increase of duty cycle,the main reason is that the liquid does not reach full pattern development at lower duty cycle.Duty cycle has a greater impact than the frequency on spray drift,the influence weights of duty cycle on airborne drift and sediment drift were 88.32%and 77.89%,respectively.At a lower PWM frequency,in addition to the droplet size,the spray drift may be affected by the pulsed spray pattern.From the perspective of reducing spray drift,it is recommended that the PWM duty cycle should be set in the range of 20%-70%to reduce the potential drift in PWM sprays.This research provides a pesticide drift reduction scheme for variable spraying technology,which can serve as a theoretical basis for PWM parameter selection.展开更多
基金Supported by the National“863”Project of China(2010AA10A301)National Technology Support Project for the 12th Five-year Plan(2011BAD20B07)
文摘Target detection is one of the key technology of precision chemical application.Previously the digital coding modulation technique was commonly used to emit and receive the optical signal in the target detection systems previously in China.It was difficult to adjust the output power,and the anti-interference ability was weak in these systems.In order to resolve these problems,the target detection method based on analog sine-wave modulation was studied.The spectral detecting system was set up in the aspects of working principle,electric circuit,and optical path.Lab testing was performed.The results showed that the reflected signal from the target varied inversely with detection distances.It indicated that it was feasible to establish the target detection system using analog sine-wave modulation technology.Furthermore,quantitative measurement of the reflected optical signal for near-infrared and visible light could be achieved by using this system.The research laid the foundation for the future development of the corresponding instrument.
文摘A new procedure of trial variational wave functional is proposed for invostigating the mass reuormalizationand the local structure of the ground state of a one-dimensional quantum sine-Gorrdonm model with linear spatial modu-lation, whose ground state differs from that without modulation. Thc phase diagram obtained in parameters (αA 2,β2)plane shows that the vertical part of the boundary between soliton lattice phase and iucommensurate (IC) phase withvanishing gap sticks at β2 = 4, the IC phase can only appear forβ2 ＞ 47r and thc IC phase regime is enlarged withincreasing spatial modulation in the case of definite parameter αA-2. The transition is of the continuous type on thevertical part of the boundary, while it is of the first order on the boundary forβ2 ＞ 47r.
文摘为探究全光纤电流互感器(fiber optical current transformer,FOCT)调制回路故障对探测器输出信号影响,便于故障预测与故障诊断,文中首先建立包含光电回路相位延迟的正弦波调制FOCT输出信号数学模型,给出调制深度与驱动电压、二次谐波、四次谐波的数学关系式,分析定目标值调制器闭环调制、解调的基本方法。在此基础上通过建立数学模型分析调制深度对探测器输出光强峰值、平均光强、二次谐波、四次谐波的影响。据此提出发生调制回路故障时调制深度降低是导致探测器输出信号异常的关键因素,探测器输出平均光强增大、四次谐波降低、二次/四次谐波比值增加应作为调制回路故障的典型特征。最后开展实际FOCT模拟试验证明理论研究的有效性。
文摘正弦波调制全光纤电流互感器(fiber optical current transformer,FOCT)因具备动态范围大、不与一次主回路连接、绝缘性能好、无铁磁饱和等优点,成为特高压换流站重要的测量设备。但在实际运行过程中,FOCT故障率远高于电磁互感器,而光回路故障是最为常见的故障类型。针对此,首先建立FOCT数学模型,提出二次谐波、光强峰值、平均光强应作为重要监测量;在此基础上分析光回路故障对探测器输出信号的影响,提出基于驱动电流及探测器输出信号变化的光回路故障预警方法,通过阈值设置及平均光强趋势判断等辨识真实的光回路故障。最后开展现场试验验证,证明该预警方法的有效性。
文摘A large amount of switching loss occurs in the inverter. From this point of view, an inverter design should be optimized for which size and cost will be minimum along with increasing efficiency. The main aim of this paper is the analysis and development of single-phase and three-phase inverter to design with MOSFET and IGBT as power elements by sinusoidal pulse width modulation (SPWM) technique using MATLAB Simulink software and compare their difference with the practical inverter. This work proposes different multilevel stages for the cascaded H-Bridge inverter to enhance the output voltages. Then compare their performance, harmonic distortion, and frequency spectrum. The hardware of an inverter circuit has been developed using the SG3524 microcontroller. The main goal of this design is to generate a sine wave with fewer harmonics, while keeping the cost and complexity of the circuit low. The designed inverter has undergone testing with different AC loads and is primarily intended for low-power applications, as lamps, fans, and chargers. This design aims to provide a reliable and efficient inverter solution for these specific applications.
基金The authors acknowledge that this research was financially supported by National Key R&D Program of China(2019YFD1101102-3)National Natural Science Foundation of China(32071907)+1 种基金Outstanding Scientist Cultivation Project of Beijing Academy of Agriculture and Forestry Sciences(JKZX202205)Qingyuan Smart Agriculture Research Institute+New R&D Institutions Construction in North and West Guangdong(2019B090905006).
文摘Pulse-width modulation(PWM)sprays can improve flow accuracy by adjusting duty cycle and frequency signal which accurately controls the relative proportion of opening time of solenoid valve.The objective of this research was to determine the impacts of PWM duty cycle and frequency on spray drift characteristic.Spray tests were conducted in a wind tunnel with a PWM variable-rate spraying system.The airborne drift and sediment drift were determined with tracer method,and the drift potential reduction(DPR)compared with reference condition of 100%duty cycle at vertical profile and horizontal planes were calculated,respectively.The results show that,at a given frequency,droplet size decreases with the increase of duty cycle,the main reason is that the liquid does not reach full pattern development at lower duty cycle.Duty cycle has a greater impact than the frequency on spray drift,the influence weights of duty cycle on airborne drift and sediment drift were 88.32%and 77.89%,respectively.At a lower PWM frequency,in addition to the droplet size,the spray drift may be affected by the pulsed spray pattern.From the perspective of reducing spray drift,it is recommended that the PWM duty cycle should be set in the range of 20%-70%to reduce the potential drift in PWM sprays.This research provides a pesticide drift reduction scheme for variable spraying technology,which can serve as a theoretical basis for PWM parameter selection.
