Multi-blade rubbing characteristics of the shaft-disk-blade-casing system with large rotation

Blade rubbing faults cause detrimental impact on the operation of aeroengines. Most of the existing studies on blade rubbing in the shaft-disk-blade-casing(SDBC) system have overlooked the elastic deformation of the blade, while some only consider the whirl of the rotor, neglecting its spin. To address these limitations, this paper proposes a dynamic model with large rotation for the SDBC system. The model incorporates the spin and whirl of the rotor, enabling the realistic reproduction of multiblade rubbing faults. To verify the accuracy of the SDBC model with large rotation and demonstrate its capability to effectively consider the rotational effects such as the centrifugal stiffening and gyroscopic effects, the natural characteristics and dynamic responses of the proposed model are compared with those obtained from reported research and experimental results. Furthermore, the effects of the rotating speed, contact stiffness,and blade number on the dynamic characteristics of the SDBC system with multi-blade rubbing are investigated. The results indicate that the phase angle between the rotor deflection and the unbalance excitation force increases with the increasing rotating speed,which significantly influences the rubbing penetration of each blade. The natural frequency of the SDBC system with rubbing constrain can be observed in the acceleration response of the casing and the torsional response of the shaft, and the frequency is related to the contact stiffness. Moreover, the vibration amplitude increases significantly with the product of the blade number under rubbing, and the rotating frequency approaches the natural frequency of the SDBC system. The proposed model can provide valuable insight for the fault diagnosis of rubbing in bladed rotating machinery.

{10.12}twin–twin intersection-induced lattice rotation and dynamic recrystallization in Mg–6Al–3Sn–2Zn alloy

This study investigated the formation mechanism of new grains due to twin–twin intersections in a coarse-grained Mg–6Al–3Sn–2Zn alloy during different strain rates of an isothermal compression.The results of electron backscattered diffraction investigations showed that the activated twins were primarily{10.12}tension twins,and 60°<10.10>boundaries formed due to twin–twin intersections under different strain rates.Isolated twin variants with 60°<10.10>boundaries transformed into new grains through lattice rotations at a low strain rate(0.01 s^(−1)).At a high strain rate(10 s^(−1)),the regions surrounded by subgrain boundaries through high-density dislocation arrangement and the 60°<10.10>boundaries transformed into new grains via dynamic recrystallization.

Complementary-Label Adversarial Domain Adaptation Fault Diagnosis Network under Time-Varying Rotational Speed andWeakly-Supervised Conditions

Recent research in cross-domain intelligence fault diagnosis of machinery still has some problems,such as relatively ideal speed conditions and sample conditions.In engineering practice,the rotational speed of the machine is often transient and time-varying,which makes the sample annotation increasingly expensive.Meanwhile,the number of samples collected from different health states is often unbalanced.To deal with the above challenges,a complementary-label(CL)adversarial domain adaptation fault diagnosis network(CLADAN)is proposed under time-varying rotational speed and weakly-supervised conditions.In the weakly supervised learning condition,machine prior information is used for sample annotation via cost-friendly complementary label learning.A diagnosticmodel learning strategywith discretized category probabilities is designed to avoidmulti-peak distribution of prediction results.In adversarial training process,we developed virtual adversarial regularization(VAR)strategy,which further enhances the robustness of the model by adding adversarial perturbations in the target domain.Comparative experiments on two case studies validated the superior performance of the proposed method.

Preheating-assisted solid-state friction stir repair of Al-Mg-Si alloy plate at different rotational speeds

Additive friction stir deposition(AFSD)is a novel structural repair and manufacturing technology has become a research hotspot at home and abroad in the past five years.In this work,the microstructural evolution and mechanical performance of the Al-Mg-Si alloy plate repaired by the preheating-assisted AFSD process were investigated.To evaluate the tool rotation speed and substrate preheating for repair quality,the AFSD technique was used to additively repair 5 mm depth blind holes on 6061 aluminum alloy substrates.The results showed that preheat-assisted AFSD repair significantly improved joint bonding and joint strength compared to the control non-preheat substrate condition.Moreover,increasing rotation speed was also beneficial to improve the metallurgical bonding of the interface and avoid volume defects.Under preheating conditions,the UTS and elongation were positively correlated with rotation speed.Under the process parameters of preheated substrate and tool rotation speed of 1000 r/min,defect-free specimens could be obtained accompanied by tensile fracture occurring in the substrate rather than the repaired zone.The UTS and elongation reached the maximum values of 164.2MPa and 13.4%,which are equivalent to 99.4%and 140%of the heated substrate,respectively.

Dual-Fields Rotational Total Skin Electron Therapy: Investigation and Implementation

Purpose: To present a protocol of a dual-field rotational (DFR) total skin electron therapy (TSET) and to provide an assessment of clinical implementation, dosimetry properties, and skin dose evaluation. Methods and Materials: The DFR-TSET combined the Stanford 6-field and McGill rotational methods. Dual 6 MeV electron beams in high dose total skin electron mode were used for DFR-TSET on a commercial linac. Beam profiles and dosimetric properties were measured using solid phantoms. The dose rate at expanded source-to-surface distance (SSD) was a combination of static rate and rotational rate. In vivo dosimetry of patient skin was performed on patients’ skin using film, metal oxide semiconductor field-effect transistors (MOSFET), and optically stimulated luminescent dosimeters (OSLD). Results: Dual field rotational total skin electron therapy exhibited good (≤±10%) uniformity in the beam profiles in the vertical direction at an extended SSD of 332 cm with a gantry angulation of ±20˚ deviated from the horizontal direction. In-vivo measurements confirmed acceptable uniformity of the patients’ total body surfaces and revealed anatomically self-blocked or shielded areas where underdosing occurred. Conclusions: The clinical implementation of DFR-TSET effectively utilizes the special mode on a linac. This technique provides short beam-on times, uniform dose distribution, large treatment field, and reduced dose of x-ray contamination to the patients. In-vivo measurements indicate satisfactory delivery and dose uniformity of the prescribed dose. Electron boost fields are recommended at normal SSDs to address underdosed areas.

Investigation on the roles of equilibrium toroidal rotation during edge-localized mode mitigated by resonant magnetic perturbations

The effects of equilibrium toroidal rotation during edge-localized mode(ELM)mitigated by resonant magnetic perturbation(RMP)are studied with the experimental equilibria of the EAST tokamak based on the four-field model in the BOUT++code.As the two main parameters to determine the toroidal rotation profiles,the rotation shear and magnitudes were separately scanned to investigate their roles in the impact of RMPs on peeling-ballooning(P-B)modes.On one hand,the results show that strong toroidal rotation shear is favorable for the enhancement of the self-generated E×B shearing rate<ω_(E×B)>with RMPs,leading to significant ELM mitigation with RMP in the stronger toroidal rotation shear region.On the other hand,toroidal rotation magnitudes may affect ELM mitigation by changing the penetration of the RMPs,more precisely the resonant components.RMPs can lead to a reduction in the pedestal energy loss by enhancing the multimode coupling in the turbulence transport phase.The shielding effects on RMPs increase with the toroidal rotation magnitude,leading to the enhancement of the multimode coupling with RMPs to be significantly weakened.Hence,the reduction in pedestal energy loss by RMPs decreased with the rotation magnitude.In brief,the results show that toroidal rotation plays a dual role in ELM mitigation with RMP by changing the shielding effects of plasma by rotation magnitude and affecting<ω_(E×B)>by rotation shear.In the high toroidal rotation region,toroidal rotation shear is usually strong and hence plays a dominant role in the influence of RMP on P-B modes,whereas in the low rotation region,toroidal rotation shear is weak and has negligible impact on P-B modes,and the rotation magnitude plays a dominant role in the influence of RMPs on the P-B modes by changing the field penetration.Therefore,the dual role of toroidal rotation leads to stronger ELM mitigation with RMP,which may be achieved both in the low toroidal rotation region and the relatively high rotation region that has strong rotational shear.

Improved Units of Measure in Rotational Mechanics

The SI system of units in rotational mechanics yields correct numerical results, but it produces physically incorrect units of measure in many cases. SI units also violate the principle of general covariance—the general rule for defining continuous coordinates and units in mathematics and mathematical physics. After 30+ years of wrestling with these problems, the ultimate authority on units of measure has declared that Newton–meter and Joule are not equivalent in rotational mechanics, as they are in the rest of physics. This article proposes a simple modification to SI units called “Nonstandard International units” (“NI units”) until a better name is agreed upon. NI units yield correct numerical results and physically correct units of measure, and they satisfy the principle of general covariance. The main obstacle to the adoption of NI units is the consensus among users that the radius of rotation should have the unit meter because the radius can be measured with a ruler. NI units assigned to radius should have units meter/radian because the radius is a conversion factor between angular size and circumferential length, as in arclength = rθ. To manage the social consensus behind SI units, the author recommends retaining SI units as they are, and informing users who want correct units that NI units solve the technical problems of SI units.

Retrospective Case Series on The Enduring Rotational Stability of The AcrySof IQ Toric Intraocular Lens in Cataract Patients Suffering from Myopia

Objective:To analyze the enduring rotational steadiness of AcrySof IQ Toric intraocular lens(IOL)in cataract patients suffering from myopia in a long-term study.Methods:A retrospective study was conducted on a case series involving 78 patients.A total of 120 eyes with an axial length(AL)ranging from 24-30 mm and corneal astigmatism≥1.50 D underwent implantation of AcrySof IQ Toric IOL guided by the version navigation system.The eyes were divided into two groups based on AL.Group A included 60 eyes with high myopia(AL≥26 mm),while Group B consisted of eyes with low to moderate myopia(24 mm≤AL<26 mm).Data on the preoperative AL were collected.Measurements were taken for residual astigmatism,the best corrected visual acuity(BCDVA),corneal astigmatism,and IOL rotation occurring between 24-and 48-months post-surgery.The percentage of eyes with an IOL rotation of under 5°and 10°was analyzed.Results:The mean length of follow-up times was recorded as 34.27±4.98,and the average rotation was 2.73±1.29°.Group A exhibited a slightly higher average rotation of 2.87±1.31°,compared to the rotation of 2.59±1.27°observed in Group B.At both the 24-36 month and 26-48 month post-operation marks,the degree of IOL rotation did not show a statistically significant difference between the two groups,with none of the patients experiencing a rotation exceeding 10°(P>0.05).The percentage of rotation degrees under 5°was recorded as 98.22%.After the procedure,the BCDVA was 0.1322±0.03 LogMAR.There was a substantial increase in theχvalue after the operation as compared to the pre-operativeχ^(2) value(χ^(2)=76.79).The standard deviation of preoperative corneal astigmatism was statistically significant(P<0.05)at 2.17±1.08 D.Following the surgical procedure,the remaining astigmatism was measured at 0.41±0.26 D.The data showed a notable gap in statistical significance(t=4.281,P<0.05).Conclusion:The AcrySof Toric IOL was a reliable solution for managing corneal astigmatism in cataract patients with myopia,demonstrating excellent long-term rotational stability.

Analysis of particle dispersion in a turbulent flow considering particle rotation

Non-spherical particles exist widely in natural and industrial fluid systems and the motions of nonspherical particles are significantly different from that of spherical particles.In this paper,a simplified model of non-spherical particles considering particle drag correction,lift,and rotation was established.Based on the Eulerian-Lagrangian simulation,the dispersion characteristics of spherical and nonspherical particles with different Stokes numbers in a high-speed turbulent jet were analyzed and compared considering the effect of particle rotation.The results show that,the differences in particle dispersion and radial velocity fluctuation between non-spherical particles and spherical particles in the jet are significant,especially when Stokes number is large.Moreover,the effects of different type of forces on the dispersion of non-spherical particles and spherical particles were compared in detail,which revealed that the change of the Magnus force caused by the increase in the angular velocity of non-spherical particles plays a dominant role in the differences of particle dispersion.

In-situ pressure-preserved coring for deep exploration:Insight into the rotation behavior of the valve cover of a pressure controller

In-situ pressure-preserved coring(IPP-Coring)is considered to be the most reliable and efficient method for the identification of the scale of oil and gas resources.During IPP-Coring,because the rotation behavior of the pressure controller valve cover in different medium environments is unclear,interference between the valve cover and inner pipe may occur and negatively affect the IPP-Coring success rate.To address this issue,we conducted a series of indoor experiments employing a high-speed camera to gain greater insights into the valve cover rotation behavior in different medium environments,e.g.,air,water,and simulated drilling fluids.The results indicated that the variation in the valve cover rotation angle in the air and fluid environments can be described by a one-phase exponential decay function with a constant time parameter and by biphasic dose response function,respectively.The rotation behavior in the fluid environments exhibited distinct elastic and gravitational acceleration zones.In the fluid environments,the density clearly impacted the valve cover closing time and rotation behavior,whereas the effect of viscosity was very slight.This can be attributed to the negligible influence of the fluid viscosity on the drag coefficient found in this study;meanwhile,the density can increase the buoyancy and the time period during which the valve cover experienced a high drag coefficient.Considering these results,control schemes for the valve cover rotation behavior during IPP-Coring were proposed for different layers and geological conditions in which the different drilling fluids should be used,e.g.,the use of a high-density valve cover in high-pore pressure layers.

Underlying slip/twinning activities of Mg-xGd alloys investigated by modified lattice rotation analysis

The inconsistencies regarding the fundamental correlation between Gd content and slip(twinning)activities of Mg alloys appeal further investigations.However,the traditional slip dislocations analysis by TEM is time-consuming,and that by SEM/EBSD cannot recognize the partial slip modes.These urge a more efficient and comprehensive approach to easily distinguish all potential slip modes occurred concurrently in alloy matrix.Here we report a modified lattice rotation analysis that can distinguish all slip systems and provide statistical results for slip activities in Mg alloy matrix.Using this method,the high ductility of Mg-Gd alloy ascribed to the enhanced non-basal slips,cross-slip,and postponed twinning activities by Gd addition is quantitatively clarified.

Rotation,Translation and Scale Invariant Sign Word Recognition Using Deep Learning

Communication between people with disabilities and people who do not understand sign language is a growing social need and can be a tedious task.One of the main functions of sign language is to communicate with each other through hand gestures.Recognition of hand gestures has become an important challenge for the recognition of sign language.There are many existing models that can produce a good accuracy,but if the model test with rotated or translated images,they may face some difficulties to make good performance accuracy.To resolve these challenges of hand gesture recognition,we proposed a Rotation,Translation and Scale-invariant sign word recognition system using a convolu-tional neural network(CNN).We have followed three steps in our work:rotated,translated and scaled(RTS)version dataset generation,gesture segmentation,and sign word classification.Firstly,we have enlarged a benchmark dataset of 20 sign words by making different amounts of Rotation,Translation and Scale of the ori-ginal images to create the RTS version dataset.Then we have applied the gesture segmentation technique.The segmentation consists of three levels,i)Otsu Thresholding with YCbCr,ii)Morphological analysis:dilation through opening morphology and iii)Watershed algorithm.Finally,our designed CNN model has been trained to classify the hand gesture as well as the sign word.Our model has been evaluated using the twenty sign word dataset,five sign word dataset and the RTS version of these datasets.We achieved 99.30%accuracy from the twenty sign word dataset evaluation,99.10%accuracy from the RTS version of the twenty sign word evolution,100%accuracy from thefive sign word dataset evaluation,and 98.00%accuracy from the RTS versionfive sign word dataset evolution.Furthermore,the influence of our model exists in competitive results with state-of-the-art methods in sign word recognition.

NCCT for Micropolar Solid and Fluid Media Based on Internal Rotations and Rotation Rates with Rotational Inertial Physics: Model Problem Studies

This paper presents model problem studies for micropolar thermoviscoelastic solids without memory and micropolar thermoviscous fluid using micropolar non-classical continuum theories (NCCT) based on internal rotations and rotation rates in which rotational inertial physics is considered in the derivation of the conservation and balance laws (CBL). The dissipation mechanism is due to strain rates as well as rotation rates. Model problems are designed to demonstrate and illustrate various significant aspects of the micropolar NCCT with rotational inertial physics considered in this paper. In case of micropolar solids, the translational and rotational waves are shown to coexist. In the absence of microconstituents (classical continuum theory, CCT) the internal rotations are a free field, hence have no influence on CCT. Absence of gradients of displacements and strains in micropolar thermoviscous fluid medium prohibits existence of translational waves as well as rotational waves even though the appearance of the mathematical model is analogous to the solids, but in terms of strain rates. It is shown that in case of micropolar thermoviscous fluids the BAM behaves more like time dependent diffusion equation i.e., like heat conduction equation in Lagrangian description. The influence of rotational inertial physics is demonstrated using BLM as well as BAM in the model problem studies.

Local Rotational Jamming and Multi-Stage Hyperuniformities in an Active Spinner System

An active system consisting of many self-spinning dimers is simulated, and a distinct local rotational jamming transition is observed as the density increases. In the low density regime, the system stays in an absorbing state,in which each dimer rotates independently subject to the applied torque;while in the high density regime,a fraction of the dimers become rotationally jammed into local clusters, and the system exhibits microphaseseparation like two-phase morphologies. For high enough densities, the system becomes completely jammed in both rotational and translational degrees of freedom. Such a simple system is found to exhibit rich and multiscale disordered hyperuniformities among the above phases: the absorbing state shows a critical hyperuniformity of the strongest class and subcritically preserves the vanishing density fluctuation scaling up to some length scale;the locally jammed state shows a two-phase hyperuniformity conversely beyond some length scale with respect to the phase cluster sizes;the totally jammed state appears to be a monomer crystal, but intrinsically loses large-scale hyperuniformity. These results are inspiring for designing novel phase-separation and disordered hyperuniform systems through dynamical organization.

Analysis of the Orbitation and Rotation of Celestial Bodies

We have developed a structure of dynamic knowledge for non-inertial systems, the so-called Theory of Dynamic Interactions (TDI) as a part of non-inertial dynamic knowledge, which incorporates a causal demonstration of phenomena accelerated by rotation, which would complement Classical Mechanics. We believe that the TDI mathematical model that we propose is of great conceptual importance. In addition, we think that it is not only necessary to understand the dynamics of rotating bodies, but also to understand the dynamics of the cosmos, with bodies that orbit and with constantly recurring movements, which make possible systems that have been in dynamic equilibrium for centuries and are not in a process of unlimited expansion. We even believe that this new dynamic theory allows us a better understanding of our universe, and the matter from which it is made.

A Meta-analysis of No-tillage Effects on Greenhouse Gas Emissions from Wheat-based Rotation Cropping Agroecosystem in China

Globally,agricultural soils are considered as one of the most important sources of greenhouse gas(GHG)emissions.No-tillage(NT),one of the most admired ways of climate-smart agriculture,has been deemed to have co-benefit to mitigation of GHG emissions and sustainability for crop yield,however,the effect of NT on GHG emissions is controversial.This study analyzed the overall effects of NT on GHG emissions,as well as the moderators that significantly influenced the overall effects,of the wheat-based rotation cropping systems in China through meta-analysis.The results showed that the overall effect size of NT on methane(CH4)uptake,nitrous oxide(N2O)emission,and global warming potential(GWP)was 0.70(95%Confidence Interval(CI):0.21–1.19),-0.27(95%CI:-0.72–0.18),and-0.39(95%CI:-1.01–0.23),respectively.In temperate climate zones with alkaline soils,the nitrogen application rate of 120–240 kg/ha,NT could significantly reduce GHG emissions and GWP.However,the mitigation effect will be weakened along with NT duration,except for proper straw addition.Overall,NT has the potential to reduce GHG emissions from wheat-based rotation systems in China,but it is necessary to implement NT depending on local conditions,soil characteristics,and field management.

Acute micro-macular hole associating with extensive intraoperative rotation of implantable collamer lens without ophthalmic viscosurgical device assistance:a case report

Dear Editor,We are writing this letter to report a micro-macular hole(mMH)following the intraoperative rotation of implantable collamer lens(ICL,V4c,Staar Surgical,Monrovia,CA,USA)without ophthalmic viscosurgical device(OVD)assistance and eventually this mMH closed spontaneously.

Cenozoic Age Counterclockwise Rotation in the Northwest End of the Sierras Pampeanas, Argentina

Investigations into the Andean orocline revealed a counterclockwise rotation of about 37° in the north and a clockwise rotation of about 29° in the south. This rotation would have started in the Eocene because the Nazca and South American plates converged. The transition zone between the Puna and the Sierras Pampeanas has a clockwise rotation pattern. Our new data show that the NE convergence of the Nazca and South American plates caused the counterclockwise rotation around the NW end of the Sierras Pampeanas. The temperature rise during a magmatic activity at 13 Ma would have favored a counterclockwise rotation of the mountain blocks of about 20° on a detachment zone within 10 to 15 km of depth. These range rotations generated local stress tensors trending NE and NW, facilitating the development of valleys, basins, mineralized dikes, mineral deposits, and alluvial fans separated from their origin. The Atajo fault shows both ductile and brittle characteristics. A mylonitic belt from the Sierra de Aconquija was juxtaposed on the rocks of the Ovejería Block and the Farallón Negro Volcanic Complex by reverse vertical displacement, and a dextral horizontal component of displacement resulted in curvatures that gave rise to pull-apart basins and step over features. The Santa Maria Valley, Campo del Arenal, Hualfín Valley, and Pipanaco salt flat most likely constituted a vast early Miocene basin rarely interrupted by low feature relief.

Two-Stage Procrustes Rotation with Sparse Target Matrix and Least Squares Criterion with Regularization and Generalized Weighting

In factor analysis, a factor loading matrix is often rotated to a simple target matrix for its simplicity. For the purpose, Procrustes rotation minimizes the discrepancy between the target and rotated loadings using two types of approximation: 1) approximate the zeros in the target by the non-zeros in the loadings, and 2) approximate the non-zeros in the target by the non-zeros in the loadings. The central issue of Procrustes rotation considered in the article is that it equally treats the two types of approximation, while the former is more important for simplifying the loading matrix. Furthermore, a well-known issue of Simplimax is the computational inefficiency in estimating the sparse target matrix, which yields a considerable number of local minima. The research proposes a new rotation procedure that consists of the following two stages. The first stage estimates sparse target matrix with lesser computational cost by regularization technique. In the second stage, a loading matrix is rotated to the target, emphasizing on the approximation of non-zeros to zeros in the target by least squares criterion with generalized weighing that is newly proposed by the study. The simulation study and real data examples revealed that the proposed method surely simplifies loading matrices.

The Sun’s Rotation Appears Differential plus Other New Views

This is a fresh perspective on the sun that considers its huge spherical size in relation to the finite speed of light. The sun is so extended that it takes light approximately 2.32 seconds to travel from the plane of the solar limb to the plane tangential to the sun at the solar disc’s center. The aforementioned information is utilized in this study to support the new viewpoints. Firstly, it is shown that the solar disc is a simultaneous view of successively emitted coaxial spherical circles. Secondly, despite the fact that the sun is gaseous, it is thought to revolve completely as a rigid body at a fixed angular speed, yet an observer on Earth sees it rotate differentially. In a simple mathematical approach, it is found that the sun’s rotational speed apparently decreases with latitude. Thirdly, a qualitative examination of how we observe simultaneous whole-surface brightness changes of the sun and sunlike stars indicates that such changes would appear to spread out radially from the center of the solar disc.