Cracks have consistently been a significant challenge limiting the development of additive manufactured nickel-based superalloys.It is essential to investigate the location of cracks and their forming mechanism.This s...Cracks have consistently been a significant challenge limiting the development of additive manufactured nickel-based superalloys.It is essential to investigate the location of cracks and their forming mechanism.This study extensively examines the impact of solidification process,microstructural evolution,and stress concentration on crack initiation during direct energy deposition(DED).The results emphasize that the crack formation is significantly related to large-angle grain boundaries,rapid cooling rates.Cracks caused by large-angle grain boundaries and a fast-cooling rate predominantly appear near the edge of the deposited samples.Liquation cracks are more likely to form near the top of the deposited sample,due to the presence ofγ/γ'eutectics.The secondary dendritic arm and the carbides in the interdendritic regions can obstruct liquid flow during the final stage of solidification,which results in the formation of solidification cracks and voids.This work paves the way to avoid cracks in nickel-based superalloys fabricated by DED,thereby enhancing the performance of superalloys.展开更多
The oxidation behavior of a novel Ni-based single-crystal 4774DD1 superalloy for industrial gas turbine applications was investigated by the isothermal oxidation at 980℃ and discontinuous oxidation weight gain method...The oxidation behavior of a novel Ni-based single-crystal 4774DD1 superalloy for industrial gas turbine applications was investigated by the isothermal oxidation at 980℃ and discontinuous oxidation weight gain methods.The phase constitution and morphology of surface oxides and the characteristics of the crosssection oxide film were analyzed by XRD,SEM and EDS.Results show that the oxidation kinetics of the 4774DD1 superalloy follows the cubic law,indicating its weak oxidation resistance at this temperature.As the oxidation time increases,the composition of the oxide film evolves as following:One layer consisting of a bottom Al_(2)O_(3)sublayer and an upper(Al_(2)O_(3)+NiO)mixture sublayer after oxidized for 25 h.Then,two layers composed of an outermost small NiO discontinuous grain layer and an internal layer for 75 h.This internal layer is consisted of the bottom Al_(2)O_(3)sublayer,an intermediate narrow CrTaO_(4)sublayer,and an upper(Al_(2)O_(3)+NiO)mixture sublayer.Also two layers comprising an outermost relative continuous NiO layer with large grain size and an internal layer as the oxidation time increases to 125 h.This internal layer is composed of the upper(Al_(2)O_(3)+NiO)mixture sublayer,an intermediate continuous(CrTaO_(4)+NiWO_(4))mixture sublayer,and a bottom Al_(2)O_(3)sublayer.Finally,three layers consisting of an outermost(NiAl2O_(4)+NiCr2O_(4))mixture layer,an intermediate(CrTaO_(4)+NiWO_(4))mixture layer,and a bottom Al_(2)O_(3)layer for 200 h.展开更多
The influence of crystal orientations on the low-cycle fatigue(LCF) behavior of a 3Re-bearing Ni-based single-crystal superalloy at 980 °C has been investigated. It is found that the orientation dependence of the...The influence of crystal orientations on the low-cycle fatigue(LCF) behavior of a 3Re-bearing Ni-based single-crystal superalloy at 980 °C has been investigated. It is found that the orientation dependence of the fatigue life not only depends on the elastic modulus, but also the number of active slip planes and the plasticity of materials determine the LCF life,especially for the [011] and [111] specimens. The [011] and [111] specimens with better plasticity withstand relatively concentrated inelastic deformation caused by fewer active slip planes, compared to the [001] specimens resisting widespread deformation caused by a higher number of active slip planes. Additionally, fatigue fracture is also influenced by cyclic plastic deformation mechanisms of the alloy with crystal orientations, and the [001] specimens are plastically deformed by wave slip mechanism and fracture along the non-crystallographic plane, while the [011] and [111] specimens are plastically deformed by planar slip mechanism and fracture along the crystallographic planes. Moreover, casting pores,eutectics, inclusions and surface oxide layers not only initiate the crack, but also reduce the stress concentration around crack tips. Our results throw light upon the effect of inelastic strain on the LCF life and analyze the cyclic plastic deformation for the alloy with different orientations.展开更多
The conventional fabrication process for single-crystal nickel-based superalloy materials is directional solidifica-tion,which is classified as casting.With the rapid development of additive manufacturing(AM)technolog...The conventional fabrication process for single-crystal nickel-based superalloy materials is directional solidifica-tion,which is classified as casting.With the rapid development of additive manufacturing(AM)technologies,a novel process for fabricating single-crystal superalloys has become possible.This article reviews recent research on the AM of single-crystal nickel-based superalloys.Laser AM technologies,particularly directed energy deposition,are mainly used to repair single-crystal materials.Electron beam powder bed fusion is an innovative method for the direct fabrication of single-crystal materials.Accordingly,the mechanisms of single-crystal formation during AM are analyzed to elucidate the potential of this process route.Furthermore,this article discusses the challenges faced by AM for single-crystal fabrication,and provides perspectives on the trends of future developments.展开更多
The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindric...The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.展开更多
Selective laser melting(SLM),an additive manufacturing process mostly applied in the metal material field,can fabricate complex-shaped metal objects with high precision.Nickel-based superalloy exhibits excellent mecha...Selective laser melting(SLM),an additive manufacturing process mostly applied in the metal material field,can fabricate complex-shaped metal objects with high precision.Nickel-based superalloy exhibits excellent mechanical properties at elevated temperatures and plays an important role in the aviation industry.This paper emphasizes the research of SLM processed Inconel 718,Inconel 625,CM247LC,and Hastelloy X,which are typical alloys with different strengthening mechanisms and operating temperatures.The strengthening mechanism and phase change evolution of different nickel-based superalloys under laser irradiation are discussed.The influence of laser parameters and the heat-treatment process on mechanical properties of SLM nickel-based superalloys are systematically introduced.Moreover,the attractive in-dustrial applications of SLM nickel-based superalloy and printed components are presented.Finally,the prospects for nickel-based superalloy materials for SLM technology are presented.展开更多
Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at ...Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at high temperatures.Fusion welding serves as an effective means for joining and repairing these alloys;however,fusion welding-induced liquation cracking has been a challenging issue.This paper comprehensively reviewed recent liquation cracking,discussing the formation mechanisms,cracking criteria,and remedies.In recent investigations,regulating material composition,changing the preweld heat treatment of the base metal,optimizing the welding process parameters,and applying auxiliary control methods are effective strategies for mitigating cracks.To promote the application of nickel-based superalloys,further research on the combination impact of multiple elements on cracking prevention and specific quantitative criteria for liquation cracking is necessary.展开更多
The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indi...The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indicate that the surface microstructure of powderschanges from dendrite into cellular stricture as the particle size of powders decrease, and thepredominant precipitates solidified on the particle surfaces were identified as MC' type carbidesenriched with Nb and Ti. It was also indicated that along with the depth of particle surfaces, thesegregation layer of S, C and O elements are thick, and that of Ti, Cr elements are thin for largesire powders while they are in reverse for median size particles.展开更多
The low-cycle fatigue (LCF) behavior of a nickel-based single crystal superalloy with [001] orientation was studied at an intermediate temperature of T0℃ and a higher temperature of To + 250℃ under a constant low...The low-cycle fatigue (LCF) behavior of a nickel-based single crystal superalloy with [001] orientation was studied at an intermediate temperature of T0℃ and a higher temperature of To + 250℃ under a constant low strain rate of 10^-3 s^-1 in ambient atmosphere. The superalloy exhibited cyclic tension-compression asymmetry which is dependent on the temperature and applied strain amplitude. Analysis on the fracture surfaces showed that the surface and subsurface casting micropores were the major crack initiation sites. Interior Ta-rich carbides were frequently observed in all specimens. Two distinct types of fracture were suggested by fractogaphy. One type was characterized by Mode-I cracking with a microscopically rough surface at To + 250℃. Whereas the other type at lower temperature T0℃ favored either one or several of the octahedral {111} planes, in contrast to the normal Mode-I growth mode typically observed at low loading frequencies (several Hz). The failure mechanisms for two cracking modes are shearing of γ' precipitates together with the matrix at T0℃ and cracking confined in the matrix and the γ/γ'interface at To - 250℃.展开更多
The service performance of the turbine blade root of an aero-engine depends on the microstructures in its superficial layer.This work investigated the surface deformation structures of turbine blade root of single cry...The service performance of the turbine blade root of an aero-engine depends on the microstructures in its superficial layer.This work investigated the surface deformation structures of turbine blade root of single crystal nickel-based superalloy produced under different creep feed grinding conditions.Gradient microstructures in the superficial layer were clarified and composed of a severely deformed layer(DFL)with nano-sized grains(48–67 nm)at the topmost surface,a DFL with submicron-sized grains(66–158 nm)and micron-sized laminated structures at the subsurface,and a dislocation accumulated layer extending to the bulk material.The formation of such gradient microstructures was found to be related to the graded variations in the plastic strain and strain rate induced in the creep feed grinding process,which were as high as 6.67 and 8.17×10^(7)s^(−1),respectively.In the current study,the evolution of surface gradient microstructures was essentially a transition process from a coarse single crystal to nano-sized grains and,simultaneously,from one orientation of a single crystal to random orientations of polycrystals,during which the dislocation slips dominated the creep feed grinding induced microstructure deformation of single crystal nickel-based superalloy.展开更多
Evaluating the recyclability of powders in additive manufacturing has been a long-term challenge.In this study,the microstructure and mechanical properties of a nickel-based superalloy fabricated by laser powder-bed f...Evaluating the recyclability of powders in additive manufacturing has been a long-term challenge.In this study,the microstructure and mechanical properties of a nickel-based superalloy fabricated by laser powder-bed fusion(LPBF)using recycled powders were investigated.Re-melted powder surfaces,satellite particles,and deformed powders were found in the recycled powders,combined with a high-oxygencontent surface layer.The increasing oxygen content led to the formation of high-density oxide inclusions;moreover,printing-induced cracks widely occurred and mainly formed along the grain boundaries in the as-built LPBF nickel-based superalloys fabricated using recycled powders.A little change in the Si or Mn content did not increase the hot cracking susceptibility(HCS)of the printed parts.The changing aspect ratio and the surface damage of the recycled powders might contribute to increasing the crack density.Moreover,the configuration of cracks in the as-built parts led to anisotropic mechanical properties,mainly resulting in extremely low ductility vertical to the building direction,and the cracks mainly propagated along the cellular boundary owing to the existence of a brittle precipitation phase.展开更多
The present research aims to establish a quantitative relation between microstructure and chemical composition (i.e., Ti, Al, and Nb) of newly designed nickel-based superalloys. This research attempts to identify an...The present research aims to establish a quantitative relation between microstructure and chemical composition (i.e., Ti, Al, and Nb) of newly designed nickel-based superalloys. This research attempts to identify an optimum microstructure at which the minimum quanti- fies of γ/γ' and γ/γ" compounds are achieved and the best castability is predicted. The results demonstrate that the highest quantity of inter- metallic eutectics (i.e., 41.5wt%) is formed at 9.8wt% (Ti + A1). A significant quantity of intermetallics formed in superalloy 1 (with a com- position of7 - 9.8wt% (Ti + A1)), which can deteriorate its castability. The type and morphology of the eutectics changed and the amount considerably decreased with decreasing Ti + A1 content in superalloy 2 (with a composition ofy - 7.6wt% (Ti + A1), 1.Swt% Nb). Thus, it is predicted that the castability would improve for superalloy 2. The same trend was observed for superalloy 4 (with a composition of 7 - 3.7wt% (Ti + A1), 4.4wt% Nb). This means that the amount of Laves increases with increasing Nb (to 4.4wt%) and decreasing Ti + A1 (to 3.7wt%) in su- peralloy 4. The best castability was predicted for superalloy 3 (with a composition ofy - 5.7wt% (Ti + A1), 2.8wt% Nb).展开更多
The mosaic structure in a Ni-based single-crystal superalloy is simulated by molecular dynamics using a potential employed in a modified analytic embedded atom method. From the calculated results we find that a closed...The mosaic structure in a Ni-based single-crystal superalloy is simulated by molecular dynamics using a potential employed in a modified analytic embedded atom method. From the calculated results we find that a closed threedimensional misfit dislocation network, with index of (011){100} and the side length of the mesh 89.6A, is formed around a cuboidal γ′ precipitate. Comparing the simulation results of the different mosaic models, we find that the side length of the mesh only depends on the lattice parameters of the γ and γ′ phases as well as the γ/γ′ interface direction, but is independent of the size and number of the cuboidal γ′ precipitate. The density of dislocations is inversely proportional to the size of the cuboidal γ′ precipitate, i.e. the amount of the dislocation is proportional to the total area of the γ/γ′ interface, which may be used to explain the relation between the amount of the fine γ′ particles and the creep rupture life of the superalloy. In addition, the closed three-dimensional networks assembled with the misfit dislocations can play a significant role in improving the mechanical properties of superalloys.展开更多
An Ni-AI-Co system embedded-atom-method potential is constructed for the γ(Ni)/γ'(Ni3A1) superalloy based on experiments and first-principles calculations. The stacking fault energies (SFEs) of the Ni(Co, A1...An Ni-AI-Co system embedded-atom-method potential is constructed for the γ(Ni)/γ'(Ni3A1) superalloy based on experiments and first-principles calculations. The stacking fault energies (SFEs) of the Ni(Co, A1) random solid solutions are calculated as a function of the concentrations of Co and A1. The calculated SFEs decrease with increasing concentrations of Co and A1, which is consistent with the experimental results. The embedding energy term in the present potential has an important influence on the SFEs of the random solid solutions. The cross-slip processes of a screw dislocation in homogenous Ni(Co) solid solutions are simulated using the present potential and the nudged elastic band method. The cross-slip activation energies increase with increasing Co concentration, which implies that the creep resistance of γ(Ni) may be improved by the addition of Co.展开更多
Single-crystal rods with different diameters and deviation angles with respect to the solidification direction were produced by Bridgman rapid solidification method at withdrawal rates of 3 and 6 mm·min^(-1) and ...Single-crystal rods with different diameters and deviation angles with respect to the solidification direction were produced by Bridgman rapid solidification method at withdrawal rates of 3 and 6 mm·min^(-1) and used as grain continuators.The crystallographic orientation of the rods,which cross-sections were perpendicular to the solidification direction at different solidification heights,was measured by electron backscattered diffraction,while the corresponding microstructures were observed by optical microscopy.The mushy zone morphology and the distribution of the temperature gradient were simulated by the finite element analysis software ProCAST.The experimental results indicate that the crystallographic orientation of the single-crystal rods corresponds to the statistical average value of all the dendrite orientations in cross-section.The crystallographic orientation of the primary and secondary dendrites of each single-crystal rod at different cross-sections fluctuates irregularly within a small range(less than 4°).The crystallographic orientation of the dendrite in each single-crystal rod is not exactly consistent with each other and is affected by their branching mode of dendrites in the solidification space.In addition,the simulation results show that the mushy zone shapes and the temperature gradient of single-crystal rods change with the increase of solidification height during the solidification process.Finally,the evolution mechanism of the crystallographic orientations and the corresponding influence factors were analyzed and discussed.展开更多
The oxidation behavior of a nickel-based superalloy at 1000°C in air was investigated through X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy analysis. A series of oxides, incl...The oxidation behavior of a nickel-based superalloy at 1000°C in air was investigated through X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy analysis. A series of oxides, including external oxide scales(Cr_2O_3,(TiO_2 + Mn Cr_2O_4)) and internal oxides(Al_2O_3,Ti N), were formed on the surface or sub-surface of the substrate at 1000°C in experimental still air. The oxidation resistance of the alloy was dependent on the stability of the surface oxide layer. The continuity and density of the protective Cr_2O_3 scale were affected by minor alloying elements such as Ti and Mn. The outermost oxide scale was composed of TiO_2 rutile and Mn Cr_2O_4 spinel, and the growth of TiO_2 particles was controlled by the outer diffusion of Ti ions through the pre-existing oxide layer. Severe internal oxidation occurred beneath the external oxide scale, consuming Al and Ti of the strength phase γ′(Ni_3(Al,Ti)) and thereby severely deteriorating the surface mechanical properties. The depth of the internal oxidation region was approximately 35 μm after exposure to experimental air at 1000°C for 80 h.展开更多
Grain growth, mechanical properties, and fracture mechanism of nickel-based GH4099 superalloy are investigated using heat treatments, tensile tests, optical microscopy (OM), and scanning electron microscopy (SEM) with...Grain growth, mechanical properties, and fracture mechanism of nickel-based GH4099 superalloy are investigated using heat treatments, tensile tests, optical microscopy (OM), and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS). The OM observation shows that the matrix grains (γ-grains) undergo an apparent growth during the solution treatment. The grain size diameter increases from 100 to 174 μm when the solution temperature rises from 1100℃ to 1160℃ for 30 min. When the holding time increases from 15 to 60 min at 1140℃, the grain size diameter increases from 140 to 176 μm, indicating that the γ-grain growth is more sensitive to temperature than time. Standard deviation, <em>S</em><sub>v</sub>, and the grain size distribution are utilized to characterize the microstructural uniformity. To predict the grain size more accurately, we develop the grain growth kinetics and find that the growth index is close to 5. The yield strength (<em>R</em><sub>p0.2</sub>), tensile strength (<em>R</em><sub>m</sub>), and ductility (<em>A</em><sub>f</sub>) are also measured. It is found that the effect decreases in the order cooling rate, solution temperature, time. <em>R</em><sub>p0.2</sub> reduces by 47% with the increase in the cooling rate from 1℃ to 8000℃/min, while both strength and ductility exhibit little changes with time. The SEM results show that the fracture surfaces have typical mixed brittle and ductile characteristics when specimens are subjected to water quenching and air cooling. However, a complete brittle fracture occurs under furnace cooling conditions. The EDS analysis indicates that the brittle γ' (Ni<sub>3</sub>Ti) phase precipitates around the γ-grain boundary during the slow cooling process, which is the main factor yielding the complete brittle fracture. Finally, the optimal solution treatment scheme for the GH4099 superalloy is proposed—a temperature of 1140℃ for 30 min followed by air cooling.展开更多
The role of niobium in nickel-based superalloys is reviewed. The importance of niobium as a strengthener is discussed. New developments in nickel-based superalloys are also briefly mentioned, including some results th...The role of niobium in nickel-based superalloys is reviewed. The importance of niobium as a strengthener is discussed. New developments in nickel-based superalloys are also briefly mentioned, including some results that show improved resistance to sulfidation by niobium. Research results from a current program on the role of niobium in the Russian powder metallurgy alloy EP741NP are presented. Future research plans on the role of niobium in superalloys are also discussed.展开更多
Finite element (FE) analysis was employed to investigate the casting microcrack and micropore growth in nickel-base single-crystal superalloys DD3. Based on the finite deformation rate-dependent crystallographic con...Finite element (FE) analysis was employed to investigate the casting microcrack and micropore growth in nickel-base single-crystal superalloys DD3. Based on the finite deformation rate-dependent crystallographic constitutive equation, the simulations of casting microcrack and micropore growth in three-dimensional unit cell model were carried out in a range of parameters including stress triaxiality, Lode parameter and type of activated slip systems. The FE results show that the stress triaxiality has profound effects on growth behavior, and the Lode parameter is also important for the casting microcrack and micropore growth. The type of operative slip systems has remarkable effect on casting microcrack and micropore growth, so the life of single- crystal component is associated with the type of activated slip systems, which is related to Schmid factor and the number of activated slip systems. The growth comparison between microcrack and micropore reveals that when the material is subjected to large deformation, the growth rate of microcrack is faster than that of micropore, i.e. microcrack is more dangerous than micropore; the microcrack is easier to result in brittle fracture than micropore. The stress triaxiality and Lode parameter have strong influence on the growth of microcrack and micropore.展开更多
基金the financial support by the Defense Industrial Technology Development Program(No.JCKY2020130C024)the National Science and Technology Major Project,China(No.Y2019-Ⅶ-0011-0151)the Science Center for Gas Turbine Project(No.P2022-C-Ⅳ-002-001)。
文摘Cracks have consistently been a significant challenge limiting the development of additive manufactured nickel-based superalloys.It is essential to investigate the location of cracks and their forming mechanism.This study extensively examines the impact of solidification process,microstructural evolution,and stress concentration on crack initiation during direct energy deposition(DED).The results emphasize that the crack formation is significantly related to large-angle grain boundaries,rapid cooling rates.Cracks caused by large-angle grain boundaries and a fast-cooling rate predominantly appear near the edge of the deposited samples.Liquation cracks are more likely to form near the top of the deposited sample,due to the presence ofγ/γ'eutectics.The secondary dendritic arm and the carbides in the interdendritic regions can obstruct liquid flow during the final stage of solidification,which results in the formation of solidification cracks and voids.This work paves the way to avoid cracks in nickel-based superalloys fabricated by DED,thereby enhancing the performance of superalloys.
基金supported by the fund of State Key Laboratory of Long-life High Temperature Materials(Grant No.DTCC28EE200787)the Natural Science Basic Research Plan in Shaanxi Province of China(Grant No.2022JQ-553)+3 种基金the China Postdoctoral Science Foundation(Grant No.2021M692555)the Excellent Youth Foundation of Shaanxi Province of China(Grant No.2021JC-08)the Beilin district of Xi’an Science and Technology Project(Grant No.GX2123)the support from the Youth Innovation Team of Shaanxi Universities。
文摘The oxidation behavior of a novel Ni-based single-crystal 4774DD1 superalloy for industrial gas turbine applications was investigated by the isothermal oxidation at 980℃ and discontinuous oxidation weight gain methods.The phase constitution and morphology of surface oxides and the characteristics of the crosssection oxide film were analyzed by XRD,SEM and EDS.Results show that the oxidation kinetics of the 4774DD1 superalloy follows the cubic law,indicating its weak oxidation resistance at this temperature.As the oxidation time increases,the composition of the oxide film evolves as following:One layer consisting of a bottom Al_(2)O_(3)sublayer and an upper(Al_(2)O_(3)+NiO)mixture sublayer after oxidized for 25 h.Then,two layers composed of an outermost small NiO discontinuous grain layer and an internal layer for 75 h.This internal layer is consisted of the bottom Al_(2)O_(3)sublayer,an intermediate narrow CrTaO_(4)sublayer,and an upper(Al_(2)O_(3)+NiO)mixture sublayer.Also two layers comprising an outermost relative continuous NiO layer with large grain size and an internal layer as the oxidation time increases to 125 h.This internal layer is composed of the upper(Al_(2)O_(3)+NiO)mixture sublayer,an intermediate continuous(CrTaO_(4)+NiWO_(4))mixture sublayer,and a bottom Al_(2)O_(3)sublayer.Finally,three layers consisting of an outermost(NiAl2O_(4)+NiCr2O_(4))mixture layer,an intermediate(CrTaO_(4)+NiWO_(4))mixture layer,and a bottom Al_(2)O_(3)layer for 200 h.
基金supported by the National Natural Science Foundation of China (Nos. 51571196, 51671188 and 5160119)Shenyang Science and Technology Project (No. 17-101-2-00)
文摘The influence of crystal orientations on the low-cycle fatigue(LCF) behavior of a 3Re-bearing Ni-based single-crystal superalloy at 980 °C has been investigated. It is found that the orientation dependence of the fatigue life not only depends on the elastic modulus, but also the number of active slip planes and the plasticity of materials determine the LCF life,especially for the [011] and [111] specimens. The [011] and [111] specimens with better plasticity withstand relatively concentrated inelastic deformation caused by fewer active slip planes, compared to the [001] specimens resisting widespread deformation caused by a higher number of active slip planes. Additionally, fatigue fracture is also influenced by cyclic plastic deformation mechanisms of the alloy with crystal orientations, and the [001] specimens are plastically deformed by wave slip mechanism and fracture along the non-crystallographic plane, while the [011] and [111] specimens are plastically deformed by planar slip mechanism and fracture along the crystallographic planes. Moreover, casting pores,eutectics, inclusions and surface oxide layers not only initiate the crack, but also reduce the stress concentration around crack tips. Our results throw light upon the effect of inelastic strain on the LCF life and analyze the cyclic plastic deformation for the alloy with different orientations.
基金supported by National Key R&D Program of China(Grant No.2017YFB1103300).
文摘The conventional fabrication process for single-crystal nickel-based superalloy materials is directional solidifica-tion,which is classified as casting.With the rapid development of additive manufacturing(AM)technologies,a novel process for fabricating single-crystal superalloys has become possible.This article reviews recent research on the AM of single-crystal nickel-based superalloys.Laser AM technologies,particularly directed energy deposition,are mainly used to repair single-crystal materials.Electron beam powder bed fusion is an innovative method for the direct fabrication of single-crystal materials.Accordingly,the mechanisms of single-crystal formation during AM are analyzed to elucidate the potential of this process route.Furthermore,this article discusses the challenges faced by AM for single-crystal fabrication,and provides perspectives on the trends of future developments.
基金financially supported by Guangdong Province Key Field R&D Program, China (No. 2019B01 0935001)the National Nature Science Foundation of China (No. 51905192)the Fundamental Research Funds for the Central Universities (No. FRT-TP-20-006A2)
文摘The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.
基金the National Nat-ural Science Foundation of China(No.51901020)Shan-dong Key Research and Development Plan Project(No.2019JZZY010327)+1 种基金Aeronautical Science Foundation of China(No.201942074001)the Fundamental Research Funds for the Central Universities,University of Science and Technology Beijing(No.FRF-IP-20-05).
文摘Selective laser melting(SLM),an additive manufacturing process mostly applied in the metal material field,can fabricate complex-shaped metal objects with high precision.Nickel-based superalloy exhibits excellent mechanical properties at elevated temperatures and plays an important role in the aviation industry.This paper emphasizes the research of SLM processed Inconel 718,Inconel 625,CM247LC,and Hastelloy X,which are typical alloys with different strengthening mechanisms and operating temperatures.The strengthening mechanism and phase change evolution of different nickel-based superalloys under laser irradiation are discussed.The influence of laser parameters and the heat-treatment process on mechanical properties of SLM nickel-based superalloys are systematically introduced.Moreover,the attractive in-dustrial applications of SLM nickel-based superalloy and printed components are presented.Finally,the prospects for nickel-based superalloy materials for SLM technology are presented.
基金financially supported by the National Science and Technology Major Project of China(No.J2019-VI-0004-0117)。
文摘Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at high temperatures.Fusion welding serves as an effective means for joining and repairing these alloys;however,fusion welding-induced liquation cracking has been a challenging issue.This paper comprehensively reviewed recent liquation cracking,discussing the formation mechanisms,cracking criteria,and remedies.In recent investigations,regulating material composition,changing the preweld heat treatment of the base metal,optimizing the welding process parameters,and applying auxiliary control methods are effective strategies for mitigating cracks.To promote the application of nickel-based superalloys,further research on the combination impact of multiple elements on cracking prevention and specific quantitative criteria for liquation cracking is necessary.
基金This work is financially supported by The National Defence Committee of ChineseTechnology(No.95-YJ-20)
文摘The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indicate that the surface microstructure of powderschanges from dendrite into cellular stricture as the particle size of powders decrease, and thepredominant precipitates solidified on the particle surfaces were identified as MC' type carbidesenriched with Nb and Ti. It was also indicated that along with the depth of particle surfaces, thesegregation layer of S, C and O elements are thick, and that of Ti, Cr elements are thin for largesire powders while they are in reverse for median size particles.
基金supported by the National Natural Science Foundation of China(No.50371042).
文摘The low-cycle fatigue (LCF) behavior of a nickel-based single crystal superalloy with [001] orientation was studied at an intermediate temperature of T0℃ and a higher temperature of To + 250℃ under a constant low strain rate of 10^-3 s^-1 in ambient atmosphere. The superalloy exhibited cyclic tension-compression asymmetry which is dependent on the temperature and applied strain amplitude. Analysis on the fracture surfaces showed that the surface and subsurface casting micropores were the major crack initiation sites. Interior Ta-rich carbides were frequently observed in all specimens. Two distinct types of fracture were suggested by fractogaphy. One type was characterized by Mode-I cracking with a microscopically rough surface at To + 250℃. Whereas the other type at lower temperature T0℃ favored either one or several of the octahedral {111} planes, in contrast to the normal Mode-I growth mode typically observed at low loading frequencies (several Hz). The failure mechanisms for two cracking modes are shearing of γ' precipitates together with the matrix at T0℃ and cracking confined in the matrix and the γ/γ'interface at To - 250℃.
基金This work was financially supported by the National Nat-ural Science Foundation of China(Nos.51921003,51775275 and 51905363)the Natural Science Foundation of Jiangsu Province(No.BK20190940)+1 种基金the National Major Science and Technology Projects of China(No.2017-VII-0002-0095)the Six Talents Summit Project in Jiangsu Province(No.JXQC-002).
文摘The service performance of the turbine blade root of an aero-engine depends on the microstructures in its superficial layer.This work investigated the surface deformation structures of turbine blade root of single crystal nickel-based superalloy produced under different creep feed grinding conditions.Gradient microstructures in the superficial layer were clarified and composed of a severely deformed layer(DFL)with nano-sized grains(48–67 nm)at the topmost surface,a DFL with submicron-sized grains(66–158 nm)and micron-sized laminated structures at the subsurface,and a dislocation accumulated layer extending to the bulk material.The formation of such gradient microstructures was found to be related to the graded variations in the plastic strain and strain rate induced in the creep feed grinding process,which were as high as 6.67 and 8.17×10^(7)s^(−1),respectively.In the current study,the evolution of surface gradient microstructures was essentially a transition process from a coarse single crystal to nano-sized grains and,simultaneously,from one orientation of a single crystal to random orientations of polycrystals,during which the dislocation slips dominated the creep feed grinding induced microstructure deformation of single crystal nickel-based superalloy.
基金This work was financially supported by the National Key Research and Development Program of China(No.2017YFB 0702300)the National Natural Science Foundation of China(No.51871028)the Fundamental Research Funds for the Central Universities(No.FRF-TP-19-003B2).
文摘Evaluating the recyclability of powders in additive manufacturing has been a long-term challenge.In this study,the microstructure and mechanical properties of a nickel-based superalloy fabricated by laser powder-bed fusion(LPBF)using recycled powders were investigated.Re-melted powder surfaces,satellite particles,and deformed powders were found in the recycled powders,combined with a high-oxygencontent surface layer.The increasing oxygen content led to the formation of high-density oxide inclusions;moreover,printing-induced cracks widely occurred and mainly formed along the grain boundaries in the as-built LPBF nickel-based superalloys fabricated using recycled powders.A little change in the Si or Mn content did not increase the hot cracking susceptibility(HCS)of the printed parts.The changing aspect ratio and the surface damage of the recycled powders might contribute to increasing the crack density.Moreover,the configuration of cracks in the as-built parts led to anisotropic mechanical properties,mainly resulting in extremely low ductility vertical to the building direction,and the cracks mainly propagated along the cellular boundary owing to the existence of a brittle precipitation phase.
文摘The present research aims to establish a quantitative relation between microstructure and chemical composition (i.e., Ti, Al, and Nb) of newly designed nickel-based superalloys. This research attempts to identify an optimum microstructure at which the minimum quanti- fies of γ/γ' and γ/γ" compounds are achieved and the best castability is predicted. The results demonstrate that the highest quantity of inter- metallic eutectics (i.e., 41.5wt%) is formed at 9.8wt% (Ti + A1). A significant quantity of intermetallics formed in superalloy 1 (with a com- position of7 - 9.8wt% (Ti + A1)), which can deteriorate its castability. The type and morphology of the eutectics changed and the amount considerably decreased with decreasing Ti + A1 content in superalloy 2 (with a composition ofy - 7.6wt% (Ti + A1), 1.Swt% Nb). Thus, it is predicted that the castability would improve for superalloy 2. The same trend was observed for superalloy 4 (with a composition of 7 - 3.7wt% (Ti + A1), 4.4wt% Nb). This means that the amount of Laves increases with increasing Nb (to 4.4wt%) and decreasing Ti + A1 (to 3.7wt%) in su- peralloy 4. The best castability was predicted for superalloy 3 (with a composition ofy - 5.7wt% (Ti + A1), 2.8wt% Nb).
基金Project supported by the State Key Development Program for Basic Research of China (Grant No G2000067102) and the National Natural Science Foundation of China (Grant No 90101004).
文摘The mosaic structure in a Ni-based single-crystal superalloy is simulated by molecular dynamics using a potential employed in a modified analytic embedded atom method. From the calculated results we find that a closed threedimensional misfit dislocation network, with index of (011){100} and the side length of the mesh 89.6A, is formed around a cuboidal γ′ precipitate. Comparing the simulation results of the different mosaic models, we find that the side length of the mesh only depends on the lattice parameters of the γ and γ′ phases as well as the γ/γ′ interface direction, but is independent of the size and number of the cuboidal γ′ precipitate. The density of dislocations is inversely proportional to the size of the cuboidal γ′ precipitate, i.e. the amount of the dislocation is proportional to the total area of the γ/γ′ interface, which may be used to explain the relation between the amount of the fine γ′ particles and the creep rupture life of the superalloy. In addition, the closed three-dimensional networks assembled with the misfit dislocations can play a significant role in improving the mechanical properties of superalloys.
基金Project supported by the National Basic Research Program of China(Grant No.2011CB606402)the National Natural Science Foundation of China(Grant No.51071091)
文摘An Ni-AI-Co system embedded-atom-method potential is constructed for the γ(Ni)/γ'(Ni3A1) superalloy based on experiments and first-principles calculations. The stacking fault energies (SFEs) of the Ni(Co, A1) random solid solutions are calculated as a function of the concentrations of Co and A1. The calculated SFEs decrease with increasing concentrations of Co and A1, which is consistent with the experimental results. The embedding energy term in the present potential has an important influence on the SFEs of the random solid solutions. The cross-slip processes of a screw dislocation in homogenous Ni(Co) solid solutions are simulated using the present potential and the nudged elastic band method. The cross-slip activation energies increase with increasing Co concentration, which implies that the creep resistance of γ(Ni) may be improved by the addition of Co.
基金supported by the National Natural Science Foundation of China(No.51674235)the National Key Research and Development Program of China(Nos.2017-VI0001-0070 and 2017-VI-0019-0091)。
文摘Single-crystal rods with different diameters and deviation angles with respect to the solidification direction were produced by Bridgman rapid solidification method at withdrawal rates of 3 and 6 mm·min^(-1) and used as grain continuators.The crystallographic orientation of the rods,which cross-sections were perpendicular to the solidification direction at different solidification heights,was measured by electron backscattered diffraction,while the corresponding microstructures were observed by optical microscopy.The mushy zone morphology and the distribution of the temperature gradient were simulated by the finite element analysis software ProCAST.The experimental results indicate that the crystallographic orientation of the single-crystal rods corresponds to the statistical average value of all the dendrite orientations in cross-section.The crystallographic orientation of the primary and secondary dendrites of each single-crystal rod at different cross-sections fluctuates irregularly within a small range(less than 4°).The crystallographic orientation of the dendrite in each single-crystal rod is not exactly consistent with each other and is affected by their branching mode of dendrites in the solidification space.In addition,the simulation results show that the mushy zone shapes and the temperature gradient of single-crystal rods change with the increase of solidification height during the solidification process.Finally,the evolution mechanism of the crystallographic orientations and the corresponding influence factors were analyzed and discussed.
基金financial support of Science and Technology Program of Jiangsu Province (Nos. BE2015144 and BE2015145)
文摘The oxidation behavior of a nickel-based superalloy at 1000°C in air was investigated through X-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy analysis. A series of oxides, including external oxide scales(Cr_2O_3,(TiO_2 + Mn Cr_2O_4)) and internal oxides(Al_2O_3,Ti N), were formed on the surface or sub-surface of the substrate at 1000°C in experimental still air. The oxidation resistance of the alloy was dependent on the stability of the surface oxide layer. The continuity and density of the protective Cr_2O_3 scale were affected by minor alloying elements such as Ti and Mn. The outermost oxide scale was composed of TiO_2 rutile and Mn Cr_2O_4 spinel, and the growth of TiO_2 particles was controlled by the outer diffusion of Ti ions through the pre-existing oxide layer. Severe internal oxidation occurred beneath the external oxide scale, consuming Al and Ti of the strength phase γ′(Ni_3(Al,Ti)) and thereby severely deteriorating the surface mechanical properties. The depth of the internal oxidation region was approximately 35 μm after exposure to experimental air at 1000°C for 80 h.
文摘Grain growth, mechanical properties, and fracture mechanism of nickel-based GH4099 superalloy are investigated using heat treatments, tensile tests, optical microscopy (OM), and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS). The OM observation shows that the matrix grains (γ-grains) undergo an apparent growth during the solution treatment. The grain size diameter increases from 100 to 174 μm when the solution temperature rises from 1100℃ to 1160℃ for 30 min. When the holding time increases from 15 to 60 min at 1140℃, the grain size diameter increases from 140 to 176 μm, indicating that the γ-grain growth is more sensitive to temperature than time. Standard deviation, <em>S</em><sub>v</sub>, and the grain size distribution are utilized to characterize the microstructural uniformity. To predict the grain size more accurately, we develop the grain growth kinetics and find that the growth index is close to 5. The yield strength (<em>R</em><sub>p0.2</sub>), tensile strength (<em>R</em><sub>m</sub>), and ductility (<em>A</em><sub>f</sub>) are also measured. It is found that the effect decreases in the order cooling rate, solution temperature, time. <em>R</em><sub>p0.2</sub> reduces by 47% with the increase in the cooling rate from 1℃ to 8000℃/min, while both strength and ductility exhibit little changes with time. The SEM results show that the fracture surfaces have typical mixed brittle and ductile characteristics when specimens are subjected to water quenching and air cooling. However, a complete brittle fracture occurs under furnace cooling conditions. The EDS analysis indicates that the brittle γ' (Ni<sub>3</sub>Ti) phase precipitates around the γ-grain boundary during the slow cooling process, which is the main factor yielding the complete brittle fracture. Finally, the optimal solution treatment scheme for the GH4099 superalloy is proposed—a temperature of 1140℃ for 30 min followed by air cooling.
文摘The role of niobium in nickel-based superalloys is reviewed. The importance of niobium as a strengthener is discussed. New developments in nickel-based superalloys are also briefly mentioned, including some results that show improved resistance to sulfidation by niobium. Research results from a current program on the role of niobium in the Russian powder metallurgy alloy EP741NP are presented. Future research plans on the role of niobium in superalloys are also discussed.
基金This work was supported by the Postdoctoral Science Foundation of China under Grant No.2004035688.
文摘Finite element (FE) analysis was employed to investigate the casting microcrack and micropore growth in nickel-base single-crystal superalloys DD3. Based on the finite deformation rate-dependent crystallographic constitutive equation, the simulations of casting microcrack and micropore growth in three-dimensional unit cell model were carried out in a range of parameters including stress triaxiality, Lode parameter and type of activated slip systems. The FE results show that the stress triaxiality has profound effects on growth behavior, and the Lode parameter is also important for the casting microcrack and micropore growth. The type of operative slip systems has remarkable effect on casting microcrack and micropore growth, so the life of single- crystal component is associated with the type of activated slip systems, which is related to Schmid factor and the number of activated slip systems. The growth comparison between microcrack and micropore reveals that when the material is subjected to large deformation, the growth rate of microcrack is faster than that of micropore, i.e. microcrack is more dangerous than micropore; the microcrack is easier to result in brittle fracture than micropore. The stress triaxiality and Lode parameter have strong influence on the growth of microcrack and micropore.