Influence of microstructure on the corrosion resistance of Fe–44Ni thin films

An Fe–44Ni nanocrystalline（NC） alloy thin film was prepared through electrodeposition. The relation between the microstructure and corrosion behavior of the NC film was investigated using electrochemical methods and chemical analysis approaches. The results show that the NC film is composed of a face-centered cubic phase（γ-（Fe,Ni）） and a body-centered cubic phase（α-（Fe,Ni）） when it is annealed at temperatures less than 400℃. The corrosion resistance increases with the increase in grain size, and the corresponding corrosion process is controlled by oxygen reduction. The NC films annealed at 500℃ and 600℃ do not exhibit the same pattern, although their grain sizes are considerably large. This result is attributed to the existence of an anodic phase, Fe0.947Ni0.054, in these films. Under this condition, the related corrosion process is synthetically controlled by anodic dissolution and depolarization.

Analytical Investigation of Prior Austenite Grain Size Dependence of Low Temperature Toughness in Steel Weld Metal

Prior austenite grain size dependence of the low temperature impact toughness has been addressed in the bainitic weld metals by in situ observations.Usually,decreasing the grain size is the only approach by which both the strength and the toughness of a steel are increased.However,low carbon bainitic steel with small grain size shows a weakening of the low temperature impact toughness in this study.By direct tracking of the morphological evolution during phase transformation,it is found that large austenite grain size dominates the nucleation of intragranular acicular ferrite,whereas small austenite grain size leads to grain boundary nucleation of bainite.This kinetics information will contribute to meet the increasing low temperature toughness requirement of weld metals for the storage tanks and offshore structures.

Effects of Strain Rate,Temperature and Grain Size on the Mechanical Properties and Microstructure Evolutions of Polycrystalline Nickel Nanowires:A Molecular Dynamics Simulation

Through molecular dynamics（MD） simulation, the dependencies of temperature, grain size and strain rate on the mechanical properties were studied. The simulation results demonstrated that the strain rate from 0.05 to 2 ns–1 affected the Young＇s modulus of nickel nanowires slightly, whereas the yield stress increased. The Young＇s modulus decreased approximately linearly; however, the yield stress firstly increased and subsequently dropped as the temperature increased. The Young＇s modulus and yield stress increased as the mean grain size increased from 2.66 to 6.72 nm. Moreover, certain efforts have been made in the microstructure evolution with mechanical properties association under uniaxial tension. Certain phenomena such as the formation of twin structures, which were found in nanowires with larger grain size at higher strain rate and lower temperature, as well as the movement of grain boundaries and dislocation, were detected and discussed in detail. The results demonstrated that the plastic deformation was mainly accommodated by the motion of grain boundaries for smaller grain size. However, for larger grain size, the formations of stacking faults and twins were the main mechanisms of plastic deformation in the polycrystalline nickel nanowire.

Humidity and seasonality drives body size patterns in males of the bush cricket Isophya rizeensis Sevgili, 2003 （Orthoptera： Tettigoniidae： Phaneropterinae）

Two primary patterns of body size variation have been recorded in ectotherms in relation to latitudinal/altitudinal shifts. In some, body size increases with increasing latitude/altitude whereas, in others, body size decreases with increasing latitude/altitude. This clinal variation is generally assumed to be caused by local adaptation to environmental conditions however the selective variable（s） （temperature, humidity, diet quality, etc.） is still heavily debated. Here we investigate geographic variation in body size of dark and pale color morphs of males of the bush-cricket lsophya rizeensis collected from 15 locations along an elevation gradient ranging from 350 to 2 500 m. Using an information theoretical approach we evaluate the relative support of four different hypotheses （the temperature size rule, the moisture gradient hypothesis, the seasonal constraint hypothesis, and the primary productivity hypothesis） explaining body size variation along the altitudinal gradient. Body size variation in pale color morphs showed a curvilinear relationship with altitude while dark color morphs showed no variation in body size. Body size variation in pale color morphs was highly correlated with precipitation and temperature seasonality values thus giving strong support for the moisture gradient and seasonal constraint hypothesis. Our results reinforce the importance of gradients in humidity and seasonality over temperature in the creation of altitudinal body size clines and the role of selection for resistance to stress factors in the establishment of these clines. Whether a body size cline is observed or not might also depend on the phenotypic properties of the individuals, like coloration.

Comparison of microstructure and property of high chromium bearing steel with and without nitrogen addition

Microstructure and property of bearing steel with and without nitrogen addition were investigated by microstructural observation and hardness measurement after different heat treatment processing. Based on the microstructural observation of both 9Cr18 steel and X90N steel, it was found that nitrogen addition could effectively reduce the amount and size of coarse carbides and also refine the original austenite grain size. Due to addition of nitrogen, more austenite phase was found in X90N steel than in 9Cr18 steel. The retained austenite of X90N steel after quenching at 1050℃ could be reduced from about 60% to about 7 9% by cold treatment at -73℃ and subsequent tempering, and thus finally increased the hardness up to 60 HRC after low temperature tempering and to 63 HRC after high temperature tempering. Furthermore, both the wear and corrosion resistance of X90N steel were found much more superior than those of 9Cr18 steel, which was attributed to the addition of nitrogen. It was proposed at last that nitrogen alloying into the high chromium bearing steel was a promising way not only to refine the size of both carbides and austenite, but also to achieve high hardness, high wear property and improved corrosion resistance of the stainless bearing steel.