The effect of ferrite content in ferrite-martensite dual-phase steel on the initiation and prop- agation of fatigue crack and the plastic deformation at crack tip has been studied.In the range of ferrite content from ...The effect of ferrite content in ferrite-martensite dual-phase steel on the initiation and prop- agation of fatigue crack and the plastic deformation at crack tip has been studied.In the range of ferrite content from 24.2 to 41.5％,the optimum seems to be 33.8％,of which the crack ini- tiation will be prolonged,the threshold value increased,the propagation rate decreased and the closure stress intensity factor increased.As the propagation force is described by effective stress intensity factor,three steels with various ferrite contents will show the same propagation behaviour on da/dN vs △ K_(eff)curve.It is shown that the closure effect increases with the decrease in △K at the fatigue crack tip.When △K equals to △K_(th),the closure effect reaches a maximum value of0.7 in a dual-phase steel with 33.8％ferrite.展开更多
ntergranular slow crack growth in zirconia polycrystal is described with a cohesive zone model that simulate mechanically the reaction-rupture mechanism underlying stress and environ- mentally assisted failure. A 2D p...ntergranular slow crack growth in zirconia polycrystal is described with a cohesive zone model that simulate mechanically the reaction-rupture mechanism underlying stress and environ- mentally assisted failure. A 2D polycrystal is considered with cohesive surfaces inserted along the grain boundaries. The anisotropic elastic modulus and grain-to-grain misorientation are accounted for together with an initial stress state related to the processing. A minimum load threshold is shown to originate from the onset of the reaction-rupture mechanism to proceed where a minimum traction is reached locally and from the magnitude of the initial compression stresses. This work aims at providing reliable predictions in long lasting applications of ceramics.展开更多
Hydrogen was a key factor resulting in stress corrosion cracking （SCC） of X80 pipeline steel in Ku＇erle soil simulated solution. In this article, the effect of hydrogen on the SCC susceptibility of X80 steel was in...Hydrogen was a key factor resulting in stress corrosion cracking （SCC） of X80 pipeline steel in Ku＇erle soil simulated solution. In this article, the effect of hydrogen on the SCC susceptibility of X80 steel was investigated further by slow strain rate tensile test, the surface fractures were observed using scanning electron microscopy （SEM）, and the fracture mechanism of SCC was discussed. The results indicate that hydrogen increases the SCC susceptibility. The SEM micrographs of hydrogen precharged samples presents a brittle quasi-cleavage feature, and pits facilitate the transgranular crack initiation. In the electrochemical impedance spectroscopy （EIS） measurement, the decreased polarization resistance and the pitting resistance of samples with hydrogen indicate that hydrogen increases the dissolution rate and deteriorates the pitting corrosion resistance. The potentiodynamic polarization curves present that hydrogen also accelerates the dissolution rate of the crack tip.展开更多
The effects of pre-deformation and strain rate on the stress corrosion cracking （SCC） behavior of aluminum alloy 2519 in air and in 3.5% NaCI water solution were investigated by means of slow strain rate tension （S...The effects of pre-deformation and strain rate on the stress corrosion cracking （SCC） behavior of aluminum alloy 2519 in air and in 3.5% NaCI water solution were investigated by means of slow strain rate tension （SSRT）, scanning electron microscopy （SEM）, and transmission electron microscopy （TEM）. The results indicate that the alloy is susceptible to SCC in 3.5% NaCI water solution and not in air. At the same pre-deformation, the alloy is more susceptible to SCC at 1.33 × 10^-5 s^-1 than at 6.66 × 10^-5 s^-1. Moreover, it is more susceptible to SCC at free pre-deformation than at 10% pre-deformation at the same strain rate. The number of 0 precipitated along the grain boundaries is reduced and distributed discontinuously, at the same time, the precipitate-free zones （PFZ） become narrow and the susceptibility to stress corrosion cracking is reduced after 10% pre-deformation.展开更多
Stress corrosion cracking （SCC） of stainless steels and Ni-based alloys in high temperature water coolant is one of the key problems affecting the safe operation of nuclear power plants （NPPs）. The nitrogen-added ...Stress corrosion cracking （SCC） of stainless steels and Ni-based alloys in high temperature water coolant is one of the key problems affecting the safe operation of nuclear power plants （NPPs）. The nitrogen-added stainless steel is a kind of possible candidate materials for mitigating SCC since reducing the carbon content and adding nitrogen to offset the loss in strength caused by the decrease in carbon content can mitigate the problem of sensitization. However, the reports of SCC of nitrogen-added stainless steels in high temperature water are few available. The effects of applied potential and sensitization treatment on the SCC of a newly developed nitrogen-containing stainless steel （SS） 316LN in high temperature water doped with chloride at 250 ℃ were studied by using slow strain rate tests （SSRTs）. The SSRT results are compared with our data previously published for 316 SS without nitrogen and 304NG SS with nitrogen, and the possible mechanism affecting the SCC behaviors of the studied steels is also discussed based on SSRT and microstucture analysis results. The susceptibility to cracking of 316LN SS normally increases with increasing potential. The susceptibility to SCC of 316LN SS was less than that of 316 SS and 304NG SS. Sensitization treatment at 700℃ for 30 h showed little effect on the S CC of 316LN S S and significant effect on the S CC of 316 S S. The predominant cracking mode for the 316LN S S in both annealed state and the state after the sensitization treatment was transgranular. The presented conditions of mitigating stress corrosion cracking are some useful information for the safe use of 316LN SS in NPPs.展开更多
Slow strain rate testing （SSRT） was employed to study the stress corrosion cracking （SCC） behavior of ZE41 magnesium alloy in 0.01 M NaCl solution. Smooth tensile specimens with different thicknesses were strained...Slow strain rate testing （SSRT） was employed to study the stress corrosion cracking （SCC） behavior of ZE41 magnesium alloy in 0.01 M NaCl solution. Smooth tensile specimens with different thicknesses were strained dynamically in both longitudinal and transverse direction under permanent immersions at a strain rate of 10-6 s-1. It is found that ZE41 magnesium alloy is susceptible to SCC in 0.01 M NaCl solution. The SCC susceptibility of the thinner specimen is lower than that of the thicker specimen. Also, the longitudinal specimens are slightly more susceptible to SCC than the transverse specimens. The SCC mechanism of magnesium alloy is attributed to the combination of anodic dissolution with hydrogen embrittlement.展开更多
The effect of hydrogen on the fractttre behaviors of Incoloy alloy 825 was investigated by means of slow strain rate testing （SSRT） Hydrogen was introduced into the sample by electrochemical charging. The results sh...The effect of hydrogen on the fractttre behaviors of Incoloy alloy 825 was investigated by means of slow strain rate testing （SSRT） Hydrogen was introduced into the sample by electrochemical charging. The results show that surface microcracks form gradually during ag- ing at room temperature when desorption of hydrogen takes place after hydrogen charging at a current density of 5 mA/cm^2 for 24 h. SSRT shows that the increase of ductility loss is significantly obvious as the hydrogen charging current density increases. Scanning electron microscopy （SEM） images reveal ductile fracture in the pre-charged sample with low current densities, while the fracture includes small quasi-cleavage regions and tends to be brittle fracture as the hydrogen charging current density increases to 5 mA/cm^2.展开更多
An AZ31 HP magnesium alloy was laser beam welded in autogenous mode with AZ61 filler using Nd-YAG laser system.Microstructural examination revealed that the laser beam weld metals obtained with or without filler mater...An AZ31 HP magnesium alloy was laser beam welded in autogenous mode with AZ61 filler using Nd-YAG laser system.Microstructural examination revealed that the laser beam weld metals obtained with or without filler material had an average grain size of about 12 μm.The microhardness and the tensile strength of the weldments were similar to those of the parent alloy.However,the stress corrosion cracking （SCC） behaviour of both the weldments assessed by slow strain rate tensile （SSRT） tests in ASTM D1384 solution was found to be slightly inferior to that of the parent alloy.It was observed that the stress corrosion cracks originated in the weld metal and propagated through the weld metal-HAZ regions in the autogenous weldment.On the other hand,in the weldment obtained with AZ61 filler material,the crack initiation and propagation was in the HAZ region.The localized damage of the magnesium hydroxide/oxide film formed on the surface of the specimens due to the exposure to the corrosive environment during the SSRT tests was found to be responsible for the SCC.展开更多
Electrochemical impedance spectroscopy(EIS) and electrochemical noise(EN) techniques were used to detect stress corrosion cracking(SCC) on 40Cr steel specimens exposed to the acidified chloride solution at ambient. To...Electrochemical impedance spectroscopy(EIS) and electrochemical noise(EN) techniques were used to detect stress corrosion cracking(SCC) on 40Cr steel specimens exposed to the acidified chloride solution at ambient. To test these two techniques,slow strain rate tensile(SSRT) tests were performed with 40Cr specimen in the identical corrosive solution at room temperature. In impedance measurements,phase shifts in frequency range from 1 to 1 000 Hz show a clear difference between the stressed and non-stressed specimens,suggesting that stress corrosion cracks are detected by the impedance measurements. EN signals in the process of SCC were recorded and then analyzed by standard deviation(STD). On the other hand,the mechanical properties,such as maximum tensile strength(MTS) and fracture strain(FS) measured by the SSRT,decrease significantly when the specimens are exposed to the corrosive solution relative to that in an inert medium. The SSRT results are consistent with fractography of the tested specimens by scanning electron microscopy(SEM). Analysis of the fracture surface clearly shows intergranular attack,suggesting that stress corrosion cracks are formed.展开更多
基金supported by the National Natural Science Foundation of China.
文摘The effect of ferrite content in ferrite-martensite dual-phase steel on the initiation and prop- agation of fatigue crack and the plastic deformation at crack tip has been studied.In the range of ferrite content from 24.2 to 41.5％,the optimum seems to be 33.8％,of which the crack ini- tiation will be prolonged,the threshold value increased,the propagation rate decreased and the closure stress intensity factor increased.As the propagation force is described by effective stress intensity factor,three steels with various ferrite contents will show the same propagation behaviour on da/dN vs △ K_(eff)curve.It is shown that the closure effect increases with the decrease in △K at the fatigue crack tip.When △K equals to △K_(th),the closure effect reaches a maximum value of0.7 in a dual-phase steel with 33.8％ferrite.
文摘ntergranular slow crack growth in zirconia polycrystal is described with a cohesive zone model that simulate mechanically the reaction-rupture mechanism underlying stress and environ- mentally assisted failure. A 2D polycrystal is considered with cohesive surfaces inserted along the grain boundaries. The anisotropic elastic modulus and grain-to-grain misorientation are accounted for together with an initial stress state related to the processing. A minimum load threshold is shown to originate from the onset of the reaction-rupture mechanism to proceed where a minimum traction is reached locally and from the magnitude of the initial compression stresses. This work aims at providing reliable predictions in long lasting applications of ceramics.
基金supported by the National Science & Technology Infrastructure Development Program of China(No.2005DKA10400)
文摘Hydrogen was a key factor resulting in stress corrosion cracking （SCC） of X80 pipeline steel in Ku＇erle soil simulated solution. In this article, the effect of hydrogen on the SCC susceptibility of X80 steel was investigated further by slow strain rate tensile test, the surface fractures were observed using scanning electron microscopy （SEM）, and the fracture mechanism of SCC was discussed. The results indicate that hydrogen increases the SCC susceptibility. The SEM micrographs of hydrogen precharged samples presents a brittle quasi-cleavage feature, and pits facilitate the transgranular crack initiation. In the electrochemical impedance spectroscopy （EIS） measurement, the decreased polarization resistance and the pitting resistance of samples with hydrogen indicate that hydrogen increases the dissolution rate and deteriorates the pitting corrosion resistance. The potentiodynamic polarization curves present that hydrogen also accelerates the dissolution rate of the crack tip.
基金financially supported by the State Key Fundamental Research Program of China (No. 2005CB623706)
文摘The effects of pre-deformation and strain rate on the stress corrosion cracking （SCC） behavior of aluminum alloy 2519 in air and in 3.5% NaCI water solution were investigated by means of slow strain rate tension （SSRT）, scanning electron microscopy （SEM）, and transmission electron microscopy （TEM）. The results indicate that the alloy is susceptible to SCC in 3.5% NaCI water solution and not in air. At the same pre-deformation, the alloy is more susceptible to SCC at 1.33 × 10^-5 s^-1 than at 6.66 × 10^-5 s^-1. Moreover, it is more susceptible to SCC at free pre-deformation than at 10% pre-deformation at the same strain rate. The number of 0 precipitated along the grain boundaries is reduced and distributed discontinuously, at the same time, the precipitate-free zones （PFZ） become narrow and the susceptibility to stress corrosion cracking is reduced after 10% pre-deformation.
基金supported by National Basic Research Program of China (973 Program, Grant No. 2006CB605005)Shanghai Municipal Committee of Science and Technology of china(Grant No. 005207019,Grant No. 08520708000)
文摘Stress corrosion cracking （SCC） of stainless steels and Ni-based alloys in high temperature water coolant is one of the key problems affecting the safe operation of nuclear power plants （NPPs）. The nitrogen-added stainless steel is a kind of possible candidate materials for mitigating SCC since reducing the carbon content and adding nitrogen to offset the loss in strength caused by the decrease in carbon content can mitigate the problem of sensitization. However, the reports of SCC of nitrogen-added stainless steels in high temperature water are few available. The effects of applied potential and sensitization treatment on the SCC of a newly developed nitrogen-containing stainless steel （SS） 316LN in high temperature water doped with chloride at 250 ℃ were studied by using slow strain rate tests （SSRTs）. The SSRT results are compared with our data previously published for 316 SS without nitrogen and 304NG SS with nitrogen, and the possible mechanism affecting the SCC behaviors of the studied steels is also discussed based on SSRT and microstucture analysis results. The susceptibility to cracking of 316LN SS normally increases with increasing potential. The susceptibility to SCC of 316LN SS was less than that of 316 SS and 304NG SS. Sensitization treatment at 700℃ for 30 h showed little effect on the S CC of 316LN S S and significant effect on the S CC of 316 S S. The predominant cracking mode for the 316LN S S in both annealed state and the state after the sensitization treatment was transgranular. The presented conditions of mitigating stress corrosion cracking are some useful information for the safe use of 316LN SS in NPPs.
基金Funded by the National Natural Science Foundation of China (No.50771093)
文摘Slow strain rate testing （SSRT） was employed to study the stress corrosion cracking （SCC） behavior of ZE41 magnesium alloy in 0.01 M NaCl solution. Smooth tensile specimens with different thicknesses were strained dynamically in both longitudinal and transverse direction under permanent immersions at a strain rate of 10-6 s-1. It is found that ZE41 magnesium alloy is susceptible to SCC in 0.01 M NaCl solution. The SCC susceptibility of the thinner specimen is lower than that of the thicker specimen. Also, the longitudinal specimens are slightly more susceptible to SCC than the transverse specimens. The SCC mechanism of magnesium alloy is attributed to the combination of anodic dissolution with hydrogen embrittlement.
文摘The effect of hydrogen on the fractttre behaviors of Incoloy alloy 825 was investigated by means of slow strain rate testing （SSRT） Hydrogen was introduced into the sample by electrochemical charging. The results show that surface microcracks form gradually during ag- ing at room temperature when desorption of hydrogen takes place after hydrogen charging at a current density of 5 mA/cm^2 for 24 h. SSRT shows that the increase of ductility loss is significantly obvious as the hydrogen charging current density increases. Scanning electron microscopy （SEM） images reveal ductile fracture in the pre-charged sample with low current densities, while the fracture includes small quasi-cleavage regions and tends to be brittle fracture as the hydrogen charging current density increases to 5 mA/cm^2.
文摘An AZ31 HP magnesium alloy was laser beam welded in autogenous mode with AZ61 filler using Nd-YAG laser system.Microstructural examination revealed that the laser beam weld metals obtained with or without filler material had an average grain size of about 12 μm.The microhardness and the tensile strength of the weldments were similar to those of the parent alloy.However,the stress corrosion cracking （SCC） behaviour of both the weldments assessed by slow strain rate tensile （SSRT） tests in ASTM D1384 solution was found to be slightly inferior to that of the parent alloy.It was observed that the stress corrosion cracks originated in the weld metal and propagated through the weld metal-HAZ regions in the autogenous weldment.On the other hand,in the weldment obtained with AZ61 filler material,the crack initiation and propagation was in the HAZ region.The localized damage of the magnesium hydroxide/oxide film formed on the surface of the specimens due to the exposure to the corrosive environment during the SSRT tests was found to be responsible for the SCC.
文摘Electrochemical impedance spectroscopy(EIS) and electrochemical noise(EN) techniques were used to detect stress corrosion cracking(SCC) on 40Cr steel specimens exposed to the acidified chloride solution at ambient. To test these two techniques,slow strain rate tensile(SSRT) tests were performed with 40Cr specimen in the identical corrosive solution at room temperature. In impedance measurements,phase shifts in frequency range from 1 to 1 000 Hz show a clear difference between the stressed and non-stressed specimens,suggesting that stress corrosion cracks are detected by the impedance measurements. EN signals in the process of SCC were recorded and then analyzed by standard deviation(STD). On the other hand,the mechanical properties,such as maximum tensile strength(MTS) and fracture strain(FS) measured by the SSRT,decrease significantly when the specimens are exposed to the corrosive solution relative to that in an inert medium. The SSRT results are consistent with fractography of the tested specimens by scanning electron microscopy(SEM). Analysis of the fracture surface clearly shows intergranular attack,suggesting that stress corrosion cracks are formed.
