A 500 N model engine filled with LO2/GCH4 was designed and manufactured.A series of ignition attempts were performed in it by both head spark plug and body spark plug.Results show that the engine can be ignited but th...A 500 N model engine filled with LO2/GCH4 was designed and manufactured.A series of ignition attempts were performed in it by both head spark plug and body spark plug.Results show that the engine can be ignited but the combustion cannot be sustained when head spark plug applied as the plug tip was set in the gaseous low-velocity zone with thin spray.This is mainly because flame from this zone cannot supply enough ignition energy for the whole chamber.However,reliable ignition and stable combustion can be achieved by body spark plug.As the O/F ratio increases from 2.61 to 3.49,chamber pressure increases from 0.474 to 0.925 MPa and combustion efficiency increases from 57.8%to 95.1%.This is determined by the injector configuration,which cannot produce the sufficiently breakup of the liquid oxygen on the low flow rate case.展开更多
This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrus...This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrust level, propellants, chamber pressure, injection pattern, film cooling parameters, material of wall and their coating, etc. The difficulties in modeling the startup and shutdown processes of thrusters lie in the fact that there are the conjugated physical processes occurring at various parameters for non-design conditions. A mathematical model to predict the thermal state of the combustion chamber for different engine operation modes is developed. To simulate the startup and shutdown processes, a quasi-steady approach is applied by replacing the transient process with time-variant operating parameters of steady-state processes. The mathematical model is based on several principles and data commonly used for heat transfer modeling: geometry of flow part, gas dynamics of flow, thermodynamics of propellants and combustion spices, convective and radiation heat flows, conjugated heat transfer between hot gas and wall, and transient approach for calculation of thermal state of construction. Calculations of the thermal state of the combustion chamber in single-turn-on mode show good convergence with the experimental results. The results of pulsed modes indicate a large temperature gradient on the internal wall surface of the chamber between pulses and the thermal state of the wall strongly depends on the pulse duration and the interval.展开更多
基金Project(613239)supported by the National Basic Research Program of China
文摘A 500 N model engine filled with LO2/GCH4 was designed and manufactured.A series of ignition attempts were performed in it by both head spark plug and body spark plug.Results show that the engine can be ignited but the combustion cannot be sustained when head spark plug applied as the plug tip was set in the gaseous low-velocity zone with thin spray.This is mainly because flame from this zone cannot supply enough ignition energy for the whole chamber.However,reliable ignition and stable combustion can be achieved by body spark plug.As the O/F ratio increases from 2.61 to 3.49,chamber pressure increases from 0.474 to 0.925 MPa and combustion efficiency increases from 57.8%to 95.1%.This is determined by the injector configuration,which cannot produce the sufficiently breakup of the liquid oxygen on the low flow rate case.
文摘This paper presents a method of thermal state calculation of combustion chamber in small thrust liquid rocket engine. The goal is to predict the thermal state of chamber wall by using basic parameters of engine: thrust level, propellants, chamber pressure, injection pattern, film cooling parameters, material of wall and their coating, etc. The difficulties in modeling the startup and shutdown processes of thrusters lie in the fact that there are the conjugated physical processes occurring at various parameters for non-design conditions. A mathematical model to predict the thermal state of the combustion chamber for different engine operation modes is developed. To simulate the startup and shutdown processes, a quasi-steady approach is applied by replacing the transient process with time-variant operating parameters of steady-state processes. The mathematical model is based on several principles and data commonly used for heat transfer modeling: geometry of flow part, gas dynamics of flow, thermodynamics of propellants and combustion spices, convective and radiation heat flows, conjugated heat transfer between hot gas and wall, and transient approach for calculation of thermal state of construction. Calculations of the thermal state of the combustion chamber in single-turn-on mode show good convergence with the experimental results. The results of pulsed modes indicate a large temperature gradient on the internal wall surface of the chamber between pulses and the thermal state of the wall strongly depends on the pulse duration and the interval.
