This study investigates the ablation of internal insulation induced by the deposition of an alumina film with different lateral film speeds.A sub-scale test solid rocket motor(SRM)was designed in an impinging jet conf...This study investigates the ablation of internal insulation induced by the deposition of an alumina film with different lateral film speeds.A sub-scale test solid rocket motor(SRM)was designed in an impinging jet configuration to form an alumina film on the sample and to encourage the lateral movement of the film by a high-speed wall jet.Fifteen static fire tests of the test SRM were conducted with six different jet velocities(V_(jet)=100 m/s,150 m/s,200 m/s,268 m/s,330 m/s,and 450 m/s)that indirectly affected the velocity of the wall jet and the deposition rate of alumina droplets.The ablation velocity was deduced from the difference in the sample thickness after a test using a coordinate measuring machine.The droplet deposition mass flux and wall jet velocity were obtained via two-phase flow simulation with the same jet velocity and effective pressure.As a result,the characteristics of alumina-induced ablation and the changes in ablation with jet velocities were obtained.The area within0.8×jet diameter was focused upon,where the ratio of ablation velocity to incoming alumina mass was constant for each jet velocity,and showed a similarity in jet structure.When the ablation velocity was increased from 2.05 to 9.98 mm/s with increasing jet velocity,the ratio of the ablation velocity and alumina mass flux decreased from 1.07×10^(-4)to 0.49×10^(-4)m^(3)/kg as Al_(2)O_(3)-C reactions became less efficient with a reduced residence time of the film.Because the decrease in residence time by the wall jet is more pronounced for slow reactions involved in Al_(2)O_(3)-C reactions,fast reactions in Al_(2)O_(3)-C reactions are less affected and result in a convergence of the volumetric rate of ablation per unit mass of alumina.展开更多
The introduction of nano-sized energetic ingredients first occurred in Russia about 60 years ago and arose great expectations in the rocket propulsion community, thanks to the higher energy densities and faster energy...The introduction of nano-sized energetic ingredients first occurred in Russia about 60 years ago and arose great expectations in the rocket propulsion community, thanks to the higher energy densities and faster energy release rates exhibited with respect to conventional ingredients. But, despite intense worldwide research programs, still today mostly laboratory level applications are reported and often for scientific purposes only. A number of practical reasons prevent the applications at industrial level: inert native coating of the energetic particles, nonuniform dispersion, aging, excessive viscosity of the slurry propellant, possible limitations in mechanical properties, more demanding safety issues, cost, and so on.This paper describes the main features in terms of performance of solid rocket propellants loaded with nanometals and intends to emphasize the unique properties or operating conditions made possible by the addition of the nano-sized energetic ingredients. Steady and unsteady combustion regimes are examined.展开更多
The instable combustion or oscillation combustion which occurs in three high capacity solid rocket motors using high energy composite propellant with finocyl grain is studied. The reasons of the acoustic combustion in...The instable combustion or oscillation combustion which occurs in three high capacity solid rocket motors using high energy composite propellant with finocyl grain is studied. The reasons of the acoustic combustion instability are also discussed. Three engineering methods that can eliminate combustion instability are proposed and discussed. The study shows that the combustion instability mainly depends on the propellant grain shape and nozzle structure. Some measures to reduce the acoustic energy and mass generation rate of combustion gas can be adopted. The test results indicate that the modified rocket motors can significantly eliminate the instable combustion and improve the motor internal ballistic performance.展开更多
The aim of this investigation is to research the initial ignition of the underwater-launching solid rocket motor.The MIXTURE multiple-phase model was set to simulate the initial ignition.The water vaporization was res...The aim of this investigation is to research the initial ignition of the underwater-launching solid rocket motor.The MIXTURE multiple-phase model was set to simulate the initial ignition.The water vaporization was researched and the energy transfer was added to the energy equations.The flow field and the vaporization were calculated coupled.The initial ignition process of the underwater solid rocket motor is obtained and the vaporization influence to the underwater launching is analyzed.The "neck","inverted jet" and "eruption" phenomenon of the bubble are observed.The bubble increases more rapidly because the steam mass added to the fuel.The temperature is lower considering the vaporization because the steam enthalpy is lower than the fuel enthalpy and the flow field of the initial ignition of the underwater-launching solid rocket motor is accordant well to the reference.展开更多
The resulting slag particles from solid rocket motor( SRM) firings are an important component of space debris environment. Slag sizes as large as 1 cm have been witnessed in ground tests,and comparable sizes have been...The resulting slag particles from solid rocket motor( SRM) firings are an important component of space debris environment. Slag sizes as large as 1 cm have been witnessed in ground tests,and comparable sizes have been also estimated via observations of sub-orbital tail-off events. We achieve slag initial data based on MASTER slag model and SRM historical launch data,and propagate slag long-term orbital evolution taking into account the zonal harmonics J2,atmospheric drag,solar radiation pressure and luni-solar attraction to discuss the slag size distribution and orbital characteristics. Finally,future slag debris environment is evaluated based on two different launch rate assumptions. The result shows that current launch frequency will make the slag population sustain growth and the population will not decrease at once even if there are no more launches in the future.展开更多
The main purpose of the present work is to study the possibilities of reducing calculation time while maintaining the validity in the numerical simulation of the combustion product flow in SPRM chamber.Three ways of d...The main purpose of the present work is to study the possibilities of reducing calculation time while maintaining the validity in the numerical simulation of the combustion product flow in SPRM chamber.Three ways of decreasing the calculation time-the use of numerical methods of high accuracy order,the reduction in spatial dimension of the problem,and the use of physical features of the processes in SPRM chamber while constructing a calculation model-were considered.Presented calculation data show that the use of these approaches makes it possible to reduce the time for solving the problems of SPRM simulation significantly(up to 100times).Also conclusions about the applicability of the mentioned above approaches in SPRM design were made.展开更多
The Al and La elements are added to the Sn9Zn alloy to obtain the fusible alloy for the mitigation devices of solid propellant rocket motors. Differential scanning calorimetry(DSC), metallographic analysis,scanning el...The Al and La elements are added to the Sn9Zn alloy to obtain the fusible alloy for the mitigation devices of solid propellant rocket motors. Differential scanning calorimetry(DSC), metallographic analysis,scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), tensile testing and fracture analysis were used to study the effect of Al and La elements on the microstructure, melting characteristics, and mechanical properties of the Sn9Zn alloy. Whether the fusible diaphragm can effectively relieve pressure was investigated by the hydrostatic pressure at high-temperature test. Experimental results show that the melting point of the Sn9Zn-0.8Al0·2La and Sn9Zn-3Al0·2La fusible alloys can meet the predetermined working temperature of ventilation. The mechanical properties of those are more than 35% higher than that of the Sn9Zn alloy at-50°C-70°C, and the mechanical strength is reduced by 80% at 175°C. It is proven by the hydrostatic pressure at high-temperature test that the fusible diaphragm can relieve pressure effectively and can be used for the design of the mitigation devices of solid propellant rocket motors.展开更多
In this paper,analytical,computational,and experimental studies are integrated to examine unsteady acoustic/vorticity transport phenomena in a solid rocket motor chamber with end-wall disturbance and side-wall injecti...In this paper,analytical,computational,and experimental studies are integrated to examine unsteady acoustic/vorticity transport phenomena in a solid rocket motor chamber with end-wall disturbance and side-wall injection.Acoustic-fluid dynamic interactions across the chamber may generate intense unsteady vorticity with associated shear stresses.These stresses may cause scouring and,in turn,enhance the heat rate and erosional burning of solid propellant in a real rocket chamber.In this modelling,the unsteady propellant gasification is mimicked by steady-state flow disturbed by end-wall oscillations.The analytical approach is formulated using an asymptotic technique to reduce the full governing equations.The equations that arise from the analysis possess wave properties are solved in an initial-boundary value sense.The numerical study is performed by solving the parabolized Navier–Stokes equations for the DNS simulation and unsteady Reynolds-averaged Navier–Stokes equations along with the energy equation using the control volume approach based on a staggered grid system with the turbulence modelling.The v2-f turbulence model has been implemented.The results show that an unexpectedly large amplitude of unsteady vorticity is generated at the injection side-wall of the chamber and is then penetrated downstream by the bulk motion of the internal flow.These stresses may cause a scouring effect and large transient heat transfer on the combustion surface.A comparison between the analytical,computational,and experimental results is performed.展开更多
The quasi one⁃dimension compressible flowfield coupled to the three⁃dimension propellant grain regression solved by the level⁃set method was used to simulate the transient internal ballistics of solid rocket motor.One...The quasi one⁃dimension compressible flowfield coupled to the three⁃dimension propellant grain regression solved by the level⁃set method was used to simulate the transient internal ballistics of solid rocket motor.One⁃dimension flowfield instead of three⁃dimension can save computational cost on the premise of calculation accuracy because the radial and azimuthal variations parameters have little contribution to the internal flowfield.The grain regression in real⁃time could provide accurate geometrical information for simulation.A combination of flowfluid solver and grain regression can reappear in a relatively real internal ballistic flowfield,so it is good for further studying the instability of solid rocket motor.For level⁃set equations,the total variation⁃diminishing second⁃order Runge⁃Kutta method for temporal derivatives and a fifth⁃order weighted⁃essentially⁃non⁃oscillatory scheme for spatial derivatives were used.The total variation⁃diminishing MacCormack method was used to discrete the Euler equations in flowfield solver.Two modules of this code were tested in this study:one is the burning rate module and the other is the nozzle erosion module.Results show that the burning rate influenced the solid rocket motor efficiency,and the velocity profile in the chamber was affected by the nozzle shape,and the nozzle erosion could influence the head⁃end pressure spike.展开更多
In order to measure the instantaneous thrust of a certain attitude-control solid rocket motor, based on the analysis of the measurement principles, the difference between the instantaneous thrust and steady thrust mea...In order to measure the instantaneous thrust of a certain attitude-control solid rocket motor, based on the analysis of the measurement principles, the difference between the instantaneous thrust and steady thrust measurements is pointed out. According to the measurement characteristics, a dynamic digital filter compensation method is presented. Combined the identification-modeling, dynamic compensation and simulation, the system's dynamic mathematic model is established. And then, a compensation digital filter is also designed. Thus, the dynamic response of the system is improved and the instantaneous thrust measurement can be implemented. The measurement results for the rocket motor show that the digital filter compensation is effective in the instantaneous thrust measurement.展开更多
China develops solid fuelrocket technology completely de-pending on its own strength.Since the late 1950s,variouskinds of solid rocket engines de-veloped by the 4th Academy ofChina Aerospace Corporation(CASC)have been...China develops solid fuelrocket technology completely de-pending on its own strength.Since the late 1950s,variouskinds of solid rocket engines de-veloped by the 4th Academy ofChina Aerospace Corporation(CASC)have been used intomany positioning and recoveringtests of various satellites and over100 flight tests of various missileswith a 100% successful rate.InOctober,1982,especially,Chinasuccessfully launched a solid fuelrocket from a submarine underwater,which reflected China’shigh level in this field.China’scivilian solid rocket engines are asfollows:展开更多
Compared with other ordinary launch vehicles, the LM-2F launch vehicle has two special systems, the fault detection processing system and launch escape system, because it is used for manned spaceflight missions. Durin...Compared with other ordinary launch vehicles, the LM-2F launch vehicle has two special systems, the fault detection processing system and launch escape system, because it is used for manned spaceflight missions. During the 10 flight missions carried out by LM-2F, only the展开更多
文摘This study investigates the ablation of internal insulation induced by the deposition of an alumina film with different lateral film speeds.A sub-scale test solid rocket motor(SRM)was designed in an impinging jet configuration to form an alumina film on the sample and to encourage the lateral movement of the film by a high-speed wall jet.Fifteen static fire tests of the test SRM were conducted with six different jet velocities(V_(jet)=100 m/s,150 m/s,200 m/s,268 m/s,330 m/s,and 450 m/s)that indirectly affected the velocity of the wall jet and the deposition rate of alumina droplets.The ablation velocity was deduced from the difference in the sample thickness after a test using a coordinate measuring machine.The droplet deposition mass flux and wall jet velocity were obtained via two-phase flow simulation with the same jet velocity and effective pressure.As a result,the characteristics of alumina-induced ablation and the changes in ablation with jet velocities were obtained.The area within0.8×jet diameter was focused upon,where the ratio of ablation velocity to incoming alumina mass was constant for each jet velocity,and showed a similarity in jet structure.When the ablation velocity was increased from 2.05 to 9.98 mm/s with increasing jet velocity,the ratio of the ablation velocity and alumina mass flux decreased from 1.07×10^(-4)to 0.49×10^(-4)m^(3)/kg as Al_(2)O_(3)-C reactions became less efficient with a reduced residence time of the film.Because the decrease in residence time by the wall jet is more pronounced for slow reactions involved in Al_(2)O_(3)-C reactions,fast reactions in Al_(2)O_(3)-C reactions are less affected and result in a convergence of the volumetric rate of ablation per unit mass of alumina.
文摘The introduction of nano-sized energetic ingredients first occurred in Russia about 60 years ago and arose great expectations in the rocket propulsion community, thanks to the higher energy densities and faster energy release rates exhibited with respect to conventional ingredients. But, despite intense worldwide research programs, still today mostly laboratory level applications are reported and often for scientific purposes only. A number of practical reasons prevent the applications at industrial level: inert native coating of the energetic particles, nonuniform dispersion, aging, excessive viscosity of the slurry propellant, possible limitations in mechanical properties, more demanding safety issues, cost, and so on.This paper describes the main features in terms of performance of solid rocket propellants loaded with nanometals and intends to emphasize the unique properties or operating conditions made possible by the addition of the nano-sized energetic ingredients. Steady and unsteady combustion regimes are examined.
文摘The instable combustion or oscillation combustion which occurs in three high capacity solid rocket motors using high energy composite propellant with finocyl grain is studied. The reasons of the acoustic combustion instability are also discussed. Three engineering methods that can eliminate combustion instability are proposed and discussed. The study shows that the combustion instability mainly depends on the propellant grain shape and nozzle structure. Some measures to reduce the acoustic energy and mass generation rate of combustion gas can be adopted. The test results indicate that the modified rocket motors can significantly eliminate the instable combustion and improve the motor internal ballistic performance.
文摘The aim of this investigation is to research the initial ignition of the underwater-launching solid rocket motor.The MIXTURE multiple-phase model was set to simulate the initial ignition.The water vaporization was researched and the energy transfer was added to the energy equations.The flow field and the vaporization were calculated coupled.The initial ignition process of the underwater solid rocket motor is obtained and the vaporization influence to the underwater launching is analyzed.The "neck","inverted jet" and "eruption" phenomenon of the bubble are observed.The bubble increases more rapidly because the steam mass added to the fuel.The temperature is lower considering the vaporization because the steam enthalpy is lower than the fuel enthalpy and the flow field of the initial ignition of the underwater-launching solid rocket motor is accordant well to the reference.
基金Sponsored by the Space Debris Special Projects of State Administration of Science Technology and Industry for National Defense(Grant No.K020410-1/2)
文摘The resulting slag particles from solid rocket motor( SRM) firings are an important component of space debris environment. Slag sizes as large as 1 cm have been witnessed in ground tests,and comparable sizes have been also estimated via observations of sub-orbital tail-off events. We achieve slag initial data based on MASTER slag model and SRM historical launch data,and propagate slag long-term orbital evolution taking into account the zonal harmonics J2,atmospheric drag,solar radiation pressure and luni-solar attraction to discuss the slag size distribution and orbital characteristics. Finally,future slag debris environment is evaluated based on two different launch rate assumptions. The result shows that current launch frequency will make the slag population sustain growth and the population will not decrease at once even if there are no more launches in the future.
基金the sponsors of the conference for financial support
文摘The main purpose of the present work is to study the possibilities of reducing calculation time while maintaining the validity in the numerical simulation of the combustion product flow in SPRM chamber.Three ways of decreasing the calculation time-the use of numerical methods of high accuracy order,the reduction in spatial dimension of the problem,and the use of physical features of the processes in SPRM chamber while constructing a calculation model-were considered.Presented calculation data show that the use of these approaches makes it possible to reduce the time for solving the problems of SPRM simulation significantly(up to 100times).Also conclusions about the applicability of the mentioned above approaches in SPRM design were made.
基金the National Natural Science Foundation of China (Grant No. 11772058)。
文摘The Al and La elements are added to the Sn9Zn alloy to obtain the fusible alloy for the mitigation devices of solid propellant rocket motors. Differential scanning calorimetry(DSC), metallographic analysis,scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), tensile testing and fracture analysis were used to study the effect of Al and La elements on the microstructure, melting characteristics, and mechanical properties of the Sn9Zn alloy. Whether the fusible diaphragm can effectively relieve pressure was investigated by the hydrostatic pressure at high-temperature test. Experimental results show that the melting point of the Sn9Zn-0.8Al0·2La and Sn9Zn-3Al0·2La fusible alloys can meet the predetermined working temperature of ventilation. The mechanical properties of those are more than 35% higher than that of the Sn9Zn alloy at-50°C-70°C, and the mechanical strength is reduced by 80% at 175°C. It is proven by the hydrostatic pressure at high-temperature test that the fusible diaphragm can relieve pressure effectively and can be used for the design of the mitigation devices of solid propellant rocket motors.
基金This research was funded by the Deanship of Scientific Research(DSR),King Abdulaziz University,Jeddah,Kingdom of Saudi Arabia,Grant No.829-722-D1435.
文摘In this paper,analytical,computational,and experimental studies are integrated to examine unsteady acoustic/vorticity transport phenomena in a solid rocket motor chamber with end-wall disturbance and side-wall injection.Acoustic-fluid dynamic interactions across the chamber may generate intense unsteady vorticity with associated shear stresses.These stresses may cause scouring and,in turn,enhance the heat rate and erosional burning of solid propellant in a real rocket chamber.In this modelling,the unsteady propellant gasification is mimicked by steady-state flow disturbed by end-wall oscillations.The analytical approach is formulated using an asymptotic technique to reduce the full governing equations.The equations that arise from the analysis possess wave properties are solved in an initial-boundary value sense.The numerical study is performed by solving the parabolized Navier–Stokes equations for the DNS simulation and unsteady Reynolds-averaged Navier–Stokes equations along with the energy equation using the control volume approach based on a staggered grid system with the turbulence modelling.The v2-f turbulence model has been implemented.The results show that an unexpectedly large amplitude of unsteady vorticity is generated at the injection side-wall of the chamber and is then penetrated downstream by the bulk motion of the internal flow.These stresses may cause a scouring effect and large transient heat transfer on the combustion surface.A comparison between the analytical,computational,and experimental results is performed.
基金Sponsored by the National Natural Science Foundation of China(Grant Nos.11872187 and 51779097)the National Natural Science Foundation of Hubei Province(Grant No.2018CFB461).
文摘The quasi one⁃dimension compressible flowfield coupled to the three⁃dimension propellant grain regression solved by the level⁃set method was used to simulate the transient internal ballistics of solid rocket motor.One⁃dimension flowfield instead of three⁃dimension can save computational cost on the premise of calculation accuracy because the radial and azimuthal variations parameters have little contribution to the internal flowfield.The grain regression in real⁃time could provide accurate geometrical information for simulation.A combination of flowfluid solver and grain regression can reappear in a relatively real internal ballistic flowfield,so it is good for further studying the instability of solid rocket motor.For level⁃set equations,the total variation⁃diminishing second⁃order Runge⁃Kutta method for temporal derivatives and a fifth⁃order weighted⁃essentially⁃non⁃oscillatory scheme for spatial derivatives were used.The total variation⁃diminishing MacCormack method was used to discrete the Euler equations in flowfield solver.Two modules of this code were tested in this study:one is the burning rate module and the other is the nozzle erosion module.Results show that the burning rate influenced the solid rocket motor efficiency,and the velocity profile in the chamber was affected by the nozzle shape,and the nozzle erosion could influence the head⁃end pressure spike.
文摘In order to measure the instantaneous thrust of a certain attitude-control solid rocket motor, based on the analysis of the measurement principles, the difference between the instantaneous thrust and steady thrust measurements is pointed out. According to the measurement characteristics, a dynamic digital filter compensation method is presented. Combined the identification-modeling, dynamic compensation and simulation, the system's dynamic mathematic model is established. And then, a compensation digital filter is also designed. Thus, the dynamic response of the system is improved and the instantaneous thrust measurement can be implemented. The measurement results for the rocket motor show that the digital filter compensation is effective in the instantaneous thrust measurement.
文摘China develops solid fuelrocket technology completely de-pending on its own strength.Since the late 1950s,variouskinds of solid rocket engines de-veloped by the 4th Academy ofChina Aerospace Corporation(CASC)have been used intomany positioning and recoveringtests of various satellites and over100 flight tests of various missileswith a 100% successful rate.InOctober,1982,especially,Chinasuccessfully launched a solid fuelrocket from a submarine underwater,which reflected China’shigh level in this field.China’scivilian solid rocket engines are asfollows:
文摘Compared with other ordinary launch vehicles, the LM-2F launch vehicle has two special systems, the fault detection processing system and launch escape system, because it is used for manned spaceflight missions. During the 10 flight missions carried out by LM-2F, only the