Aiming at the problems that the simulation accuracy which is reduced due to the simplification of the model,a three-dimensional simulation method based on solid modeling is being proposed.By analyzing the motion relat...Aiming at the problems that the simulation accuracy which is reduced due to the simplification of the model,a three-dimensional simulation method based on solid modeling is being proposed.By analyzing the motion relationship and positional relationship between the caries knife and the workpiece,the coordinate system of the caries machining was established.With the MATLAB software,the cutting edge model and the blade sweeping surface model of the boring cutter are sequentially established.Boolean operation is performed on the blade swept surface formed by the tooth cutter teeth with time t and the workpiece tooth geometry as well as the undeformed three-dimensional chip geometry model and the instantaneous cogging geometry model are obtained at different times.Through the compare between gear end face simulation tooth profile and the theoretical inner arc tooth profile,we verified the accuracy and rationality of the proposed method.展开更多
It is significant for establishing gravity datum to construct precise gravity solid tidal model,A simple method with relatively low performance is to interpolate tidal parameters from the global gravity solid tide mod...It is significant for establishing gravity datum to construct precise gravity solid tidal model,A simple method with relatively low performance is to interpolate tidal parameters from the global gravity solid tide models.A competitive approach is to determine local gravity solid tidal model by harmonic analysis using long-time serial gravity observations.In this paper a new high-precision gravity solid tidal model for Precision Gravity Measurement Facility is estimated from two co-site gravimeters in the cave laboratory using modern international standard data processing techniques,whose accuracy is evaluated further by comparing with previous publications.The results show that:(1)the determined gravity solid tidal models from two co-site gravimeters are in good agreement with each other,of which the maximum differences for amplitude factors and phase delays don’t exceed 0.01700%and 2.50990°,respectively.(2)the performance of the obtained gravity solid tidal model is 0.00411 for amplitude factors and 0.24120°for phase delays,which is a little better than that of previous publications using superconducting gravity data from Wuhan station.(3)our results and methods are corrective and effective.(4)our model is tiny different from that provided by Wuhan station,which implies that it is necessary to construct a gravity solid tidal model for Precision Gravity Measurement Facility,rather than just adopting existing models at Wuhan station.Our results are helpful in realizing the goal of Precision Gravity Measurement Facility.展开更多
In this study, a new method for conversion of solid finite element solution to beam finite element solution is developed based on the meta-modeling theory which constructs a model consistent with continuum mechanics. ...In this study, a new method for conversion of solid finite element solution to beam finite element solution is developed based on the meta-modeling theory which constructs a model consistent with continuum mechanics. The proposed method is rigorous and efficient compared to a typical conversion method which merely computes surface integration of solid element nodal stresses to obtain cross-sectional forces. The meta-modeling theory ensures the rigorousness of proposed method by defining a proper distance between beam element and solid element solutions in a function space of continuum mechanics. Results of numerical verification test that is conducted with a simple cantilever beam are used to find the proper distance function for this conversion. Time history analysis of the main tunnel structure of a real ramp tunnel is considered as a numerical example for the proposed conversion method. It is shown that cross-sectional forces are readily computed for solid element solution of the main tunnel structure when it is converted to a beam element solution using the proposed method. Further, envelopes of resultant forces which are of primary importance for the purpose of design, are developed for a given ground motion at the end.展开更多
The weakly forced vibration of an axially moving viscoelastic beam is inves- tigated. The viscoelastic material of the beam is constituted by the standard linear solid model with the material time derivative involved....The weakly forced vibration of an axially moving viscoelastic beam is inves- tigated. The viscoelastic material of the beam is constituted by the standard linear solid model with the material time derivative involved. The nonlinear equations governing the transverse vibration are derived from the dynamical, constitutive, and geometrical relations. The method of multiple scales is used to determine the steady-state response. The modulation equation is derived from the solvability condition of eliminating secular terms. Closed-form expressions of the amplitude and existence condition of nontrivial steady-state response are derived from the modulation equation. The stability of non- trivial steady-state response is examined via the Routh-Hurwitz criterion.展开更多
The principal assumptions about equivalence and energy distribution of the asdorption sites on solidsurfaces used by Langmuir for deriving the equation of monomolecular adsorption are generalized and anew physical ads...The principal assumptions about equivalence and energy distribution of the asdorption sites on solidsurfaces used by Langmuir for deriving the equation of monomolecular adsorption are generalized and anew physical adsorption model is proposed and tested with experimental data published in literature.Themodels of Langmuir,Freundlich,Temkin etc.are only the special cases.Assuming uniform density distributionof adsorption energy,the isotherm equation is given asn=K.1n[1+(bop)1/Mor n=K.1n[1+(boC)1/M]where n is the amount of adsorption per unit weight or area of solid p or C is tbe pressure of gas or the concen-tration of solution respectively.K,bo,M are constants with physical meanings as described in this paper.This equation can be used over wide range to quantitatively represent the five types of physical adsorptionclassified by Brunauer.展开更多
We present the solid model edit distance(SMED),a powerful and flexible paradigm for exploiting shape similarities amongst CAD models.It is designed to measure the magnitude of distortions between two CAD models in bou...We present the solid model edit distance(SMED),a powerful and flexible paradigm for exploiting shape similarities amongst CAD models.It is designed to measure the magnitude of distortions between two CAD models in boundary representation(B-rep).We give the formal definition by analogy with graph edit distance,one of the most popular graph matching methods.To avoid the expensive computational cost potentially caused by exact computation,an approximate procedure based on the alignment of local structure sets is provided in addition.In order to verify the flexibility,we make intensive investigations on three typical applications in manufacturing industry,and describe how our method can be adapted to meet the various requirements.Furthermore,a multilevel method is proposed to make further improvements of the presented algorithm on both effectiveness and efficiency,in which the models are hierarchically segmented into the configurations of features.Experiment results show that SMED serves as a reasonable measurement of shape similarity for CAD models,and the proposed approach provides remarkable performance on a real-world CAD model database.展开更多
A polyhedral solid modeler that operates on boundary representations (B-reps) of ob- jects must derive topological information from numerical data.Due to finite precision of the com- puter,unavoidable numerical calcul...A polyhedral solid modeler that operates on boundary representations (B-reps) of ob- jects must derive topological information from numerical data.Due to finite precision of the com- puter,unavoidable numerical calculation errors may result in ambiguous or contradictory decision of topology.These effects cause existing polyhedral modelers to fail when confronted with objects that nearly align or barely intersect. Based on analysing the reasons which cause the failure of Boolean operation to fail,this paper describes an algorithm using solid integrity to carefully design each step of Boolean operation,so that valid polyhedral modeling results may be achieved.展开更多
In conformity with the principle of Design for Manufacture,feature-based design strate- (?)es have been developed.As the“feature”is relevant to the“macro process plan”and“macro NC programs”,obviously,“feature”...In conformity with the principle of Design for Manufacture,feature-based design strate- (?)es have been developed.As the“feature”is relevant to the“macro process plan”and“macro NC programs”,obviously,“feature”is beyond the power of conventional solid modellers.Neverthe- less,substantial breakthrough has not been made in the solid modeling field,except“feature at- taching”or“feature recognizing”methods have been taken on.In this paper,the theory, concepts,system architecture,and algorithm principles of solid modeling tool system have been represented.The practice of Feature Solid Modeling Tool System (FSMTS) developed at Huazhong University has proved that the tool may be a new foundation of Feature-Based Design.展开更多
This paper establishes a new model for calculation of the standard entropies of solid binary oxides as follows: S_(29)=27.07×Φ_1+1.120×Φ_2+n_1×k×Φ, -22.19 e.u (R=0.9960) We have invesigated 103 ...This paper establishes a new model for calculation of the standard entropies of solid binary oxides as follows: S_(29)=27.07×Φ_1+1.120×Φ_2+n_1×k×Φ, -22.19 e.u (R=0.9960) We have invesigated 103 binary oxides. and found good agreemenl between estimated and experimental entropies.展开更多
The paper introduces a method for displaying cubic volume cells (voxels) resulting frompartitioning given objectS with orthogonal planes for finite difference calculation. The method representS ablock of voxels as a B...The paper introduces a method for displaying cubic volume cells (voxels) resulting frompartitioning given objectS with orthogonal planes for finite difference calculation. The method representS ablock of voxels as a B-rep solid model and conStrUcts the B-rep geometric clementS with an approach frombottom to up. Once the B-rep model is established, it is efficient in displaying because inner voxels areomitted and many coplanar facetS are merged together. By displaying the interSeCtion lines of theconstructed B-reP model and the partitioning planes, the tessellation image can be generated.展开更多
In allusion to the deficient feature of product information in conceptualdesign, a framework of deficient information modeling for conceptual shape design is put forward,which includes qualitative shape modeling (a qu...In allusion to the deficient feature of product information in conceptualdesign, a framework of deficient information modeling for conceptual shape design is put forward,which includes qualitative shape modeling (a qualitative solid model), uncertain shape modeling (anuncertain relation model) and imprecise shape modeling (an imprecise region model). In theframework, the qualitative solid model is the core, which represents qualitatively (using symbols)the conceptual shapes of mechanical products. The uncertain relation model regarding domainrelations as objects and the imprecise region model regarding domains as objects are used to dealwith the uncertain and imprecise issues respectively, which arise from qualitative shape modeling orexist in product information itself.展开更多
This paper creates 3D solid model and assembly of U RJ 92-6 oil tank and analyses its strength by integrated CAD/CAE/CAM software I-D EAS. Through integrated simulation in computer, design efficiency and quality of oi...This paper creates 3D solid model and assembly of U RJ 92-6 oil tank and analyses its strength by integrated CAD/CAE/CAM software I-D EAS. Through integrated simulation in computer, design efficiency and quality of oil tank is greatly improved. Adopting integrated CAD/CAE/CAM software to carry out integrated research to equ ipment and products, we will be able to take overall analysis in aspects of 3-D solid modeling, pre-assembly and strength, etc., to realize non-paper designi ng and parallel designing. Problems can be found and settled during designing, w hich will increase designing efficiency and one-time success rate and realize o ptimum designing for products.展开更多
In this paper,we show that for any given planar cubic algebraic curves defined by a quadratic Hamiltonian vector field,we can always have their exact explicit parametric representations. We use a model of micro-struct...In this paper,we show that for any given planar cubic algebraic curves defined by a quadratic Hamiltonian vector field,we can always have their exact explicit parametric representations. We use a model of micro-structured solid to show an application of our conclusions.展开更多
The report mainly studied the crawler frame motion platform to reduce weight and increase the intensity. Report described the structural design process which using CAD/CAE technology for solid modeling, simulation ana...The report mainly studied the crawler frame motion platform to reduce weight and increase the intensity. Report described the structural design process which using CAD/CAE technology for solid modeling, simulation analysis, parameter optimization. And it also explained the outstanding advantages of CAD/CAE technology in mechanical design as well as simulation analysis.展开更多
Ball-end mill is widely used in workpiece processi ng with free-form surfaces. Such models that can predict processing character istics precisely are very necessary to the aim of cost reducing, quality improvi ng and ...Ball-end mill is widely used in workpiece processi ng with free-form surfaces. Such models that can predict processing character istics precisely are very necessary to the aim of cost reducing, quality improvi ng and productivity progressing, the cutting force prediction is the most import ant among these models. To explore the physical essence of metal cutting, model researchers commonly simplify the geometric conditions in cutting process, and a ssume that the geometric parameters that are needed to solve the physical models have already been predefined, so it results in the separation between model res earch and practical application. In this paper, for the representative cutting f orce models of ball end milling, a new extraction method of geometric parameters is suggested, which makes it possible for physical model to actually serve for the practical manufacturing, and take in the inspection of real production.展开更多
In the present study, the dynamic response of a coupled SPM-feeder-cage system under irregular waves and shear currents is analyzed. A numerical model is developed by using the commercial software Orca Flex. Hydrodyna...In the present study, the dynamic response of a coupled SPM-feeder-cage system under irregular waves and shear currents is analyzed. A numerical model is developed by using the commercial software Orca Flex. Hydrodynamics coefficients of the vessel are calculated by using a 3D diffraction/radiation panel program. First- and second-order wave forces are included in the calculations. Morison equation is used to compute the drag force on line elements representing the net. Drag coefficients are determined at every time step in the simulation considering the relative normal velocity between the structural elements and the fluid flow. The dynamic response of the coupled system is analyzed for various environments and net materials. The results of the study show the effects of solidity ratio of the net and vertical positions of the cage on the overall dynamic response of the system, confirming the viability of this type of configuration for future development of offshore aquaculture in deep waters.展开更多
The authors carried out drop impact tests for several soft materials under a flat frontal impact condition in which a drop hammer with a flat bottom surface strikes a plate-like soft material in the normal direction. ...The authors carried out drop impact tests for several soft materials under a flat frontal impact condition in which a drop hammer with a flat bottom surface strikes a plate-like soft material in the normal direction. The experimental results indicated that the impact force waveforms of soft materials consisted of a thorn-shaped waveform and a subsequent mountain-shaped waveform. The thorn-shaped waveform was strongly affected by the strain rate. In the present study, the occurrence mechanism of this distinctive waveform was discussed from the viewpoint of the viscosity transient phenomenon. A standard linear solid (SLS) model in which the viscosity transient phenomenon was considered was applied to the simulation. Some features of the impact force waveform of soft materials could be explained by the SLS model. Furthermore, the thorn-shape waveform could also be observed in the impact force waveforms of human skin and free-falling hollow balls.展开更多
In order to alleviate unstable factor-caused bifurcation and reduce oscillations in traffic flow,a feedback control with consideration of time delay is designed for the solid angle model(SAM).The stability and bifurca...In order to alleviate unstable factor-caused bifurcation and reduce oscillations in traffic flow,a feedback control with consideration of time delay is designed for the solid angle model(SAM).The stability and bifurcation condition of the new SAM is derived through linear analysis and bifurcation analysis,and then accurate range of stable region is obtained.In order to explore the mechanism of the influence of multiple parameter combinations on the stability of controlled systems,a definite integral stabilization method is provided to determine the stable interval of time delay and feedback gain.Numerical simulations are explored to verify the feasibility and effectiveness of the proposed model,which also demonstrate that feedback gain and delay are two key factors to alleviate traffic congestion in the SAM.展开更多
基金The National Natural Science Foundation of China (No.52165060,12272189)Program for Young Talents of Science and Technology in Universities of Inner Mongolia Autonomous Region: (NJYT23022)+2 种基金Science and Technology Projects of Inner Mongolia Autonomous Region: (2021GG0432)Central Guiding Local Science and Technology Development Plan (2022ZY0013)Basic research business fee project for universities directly under Inner Mongolia Autonomous Region (GXKY22046).
文摘Aiming at the problems that the simulation accuracy which is reduced due to the simplification of the model,a three-dimensional simulation method based on solid modeling is being proposed.By analyzing the motion relationship and positional relationship between the caries knife and the workpiece,the coordinate system of the caries machining was established.With the MATLAB software,the cutting edge model and the blade sweeping surface model of the boring cutter are sequentially established.Boolean operation is performed on the blade swept surface formed by the tooth cutter teeth with time t and the workpiece tooth geometry as well as the undeformed three-dimensional chip geometry model and the instantaneous cogging geometry model are obtained at different times.Through the compare between gear end face simulation tooth profile and the theoretical inner arc tooth profile,we verified the accuracy and rationality of the proposed method.
基金supported by the National Natural Science Foundation of China(Grant No.41974014)the Open Fund of State Laboratory of Information Engineering in Surveying,Mapping and Remote Sensing,Wuhan University(Grant No.19P01)
文摘It is significant for establishing gravity datum to construct precise gravity solid tidal model,A simple method with relatively low performance is to interpolate tidal parameters from the global gravity solid tide models.A competitive approach is to determine local gravity solid tidal model by harmonic analysis using long-time serial gravity observations.In this paper a new high-precision gravity solid tidal model for Precision Gravity Measurement Facility is estimated from two co-site gravimeters in the cave laboratory using modern international standard data processing techniques,whose accuracy is evaluated further by comparing with previous publications.The results show that:(1)the determined gravity solid tidal models from two co-site gravimeters are in good agreement with each other,of which the maximum differences for amplitude factors and phase delays don’t exceed 0.01700%and 2.50990°,respectively.(2)the performance of the obtained gravity solid tidal model is 0.00411 for amplitude factors and 0.24120°for phase delays,which is a little better than that of previous publications using superconducting gravity data from Wuhan station.(3)our results and methods are corrective and effective.(4)our model is tiny different from that provided by Wuhan station,which implies that it is necessary to construct a gravity solid tidal model for Precision Gravity Measurement Facility,rather than just adopting existing models at Wuhan station.Our results are helpful in realizing the goal of Precision Gravity Measurement Facility.
文摘In this study, a new method for conversion of solid finite element solution to beam finite element solution is developed based on the meta-modeling theory which constructs a model consistent with continuum mechanics. The proposed method is rigorous and efficient compared to a typical conversion method which merely computes surface integration of solid element nodal stresses to obtain cross-sectional forces. The meta-modeling theory ensures the rigorousness of proposed method by defining a proper distance between beam element and solid element solutions in a function space of continuum mechanics. Results of numerical verification test that is conducted with a simple cantilever beam are used to find the proper distance function for this conversion. Time history analysis of the main tunnel structure of a real ramp tunnel is considered as a numerical example for the proposed conversion method. It is shown that cross-sectional forces are readily computed for solid element solution of the main tunnel structure when it is converted to a beam element solution using the proposed method. Further, envelopes of resultant forces which are of primary importance for the purpose of design, are developed for a given ground motion at the end.
基金Project supported by the National Natural Science Foundation of China (No.10972143)the Shanghai Municipal Education Commission (No.YYY11040)+2 种基金the Shanghai Leading Academic Discipline Project (No.J51501)the Leading Academic Discipline Project of Shanghai Institute of Technology(No.1020Q121001)the Start Foundation for Introducing Talents of Shanghai Institute of Technology (No.YJ2011-26)
文摘The weakly forced vibration of an axially moving viscoelastic beam is inves- tigated. The viscoelastic material of the beam is constituted by the standard linear solid model with the material time derivative involved. The nonlinear equations governing the transverse vibration are derived from the dynamical, constitutive, and geometrical relations. The method of multiple scales is used to determine the steady-state response. The modulation equation is derived from the solvability condition of eliminating secular terms. Closed-form expressions of the amplitude and existence condition of nontrivial steady-state response are derived from the modulation equation. The stability of non- trivial steady-state response is examined via the Routh-Hurwitz criterion.
文摘The principal assumptions about equivalence and energy distribution of the asdorption sites on solidsurfaces used by Langmuir for deriving the equation of monomolecular adsorption are generalized and anew physical adsorption model is proposed and tested with experimental data published in literature.Themodels of Langmuir,Freundlich,Temkin etc.are only the special cases.Assuming uniform density distributionof adsorption energy,the isotherm equation is given asn=K.1n[1+(bop)1/Mor n=K.1n[1+(boC)1/M]where n is the amount of adsorption per unit weight or area of solid p or C is tbe pressure of gas or the concen-tration of solution respectively.K,bo,M are constants with physical meanings as described in this paper.This equation can be used over wide range to quantitatively represent the five types of physical adsorptionclassified by Brunauer.
基金Supported by National Science Foundation of China(61373071)
文摘We present the solid model edit distance(SMED),a powerful and flexible paradigm for exploiting shape similarities amongst CAD models.It is designed to measure the magnitude of distortions between two CAD models in boundary representation(B-rep).We give the formal definition by analogy with graph edit distance,one of the most popular graph matching methods.To avoid the expensive computational cost potentially caused by exact computation,an approximate procedure based on the alignment of local structure sets is provided in addition.In order to verify the flexibility,we make intensive investigations on three typical applications in manufacturing industry,and describe how our method can be adapted to meet the various requirements.Furthermore,a multilevel method is proposed to make further improvements of the presented algorithm on both effectiveness and efficiency,in which the models are hierarchically segmented into the configurations of features.Experiment results show that SMED serves as a reasonable measurement of shape similarity for CAD models,and the proposed approach provides remarkable performance on a real-world CAD model database.
文摘A polyhedral solid modeler that operates on boundary representations (B-reps) of ob- jects must derive topological information from numerical data.Due to finite precision of the com- puter,unavoidable numerical calculation errors may result in ambiguous or contradictory decision of topology.These effects cause existing polyhedral modelers to fail when confronted with objects that nearly align or barely intersect. Based on analysing the reasons which cause the failure of Boolean operation to fail,this paper describes an algorithm using solid integrity to carefully design each step of Boolean operation,so that valid polyhedral modeling results may be achieved.
文摘In conformity with the principle of Design for Manufacture,feature-based design strate- (?)es have been developed.As the“feature”is relevant to the“macro process plan”and“macro NC programs”,obviously,“feature”is beyond the power of conventional solid modellers.Neverthe- less,substantial breakthrough has not been made in the solid modeling field,except“feature at- taching”or“feature recognizing”methods have been taken on.In this paper,the theory, concepts,system architecture,and algorithm principles of solid modeling tool system have been represented.The practice of Feature Solid Modeling Tool System (FSMTS) developed at Huazhong University has proved that the tool may be a new foundation of Feature-Based Design.
文摘This paper establishes a new model for calculation of the standard entropies of solid binary oxides as follows: S_(29)=27.07×Φ_1+1.120×Φ_2+n_1×k×Φ, -22.19 e.u (R=0.9960) We have invesigated 103 binary oxides. and found good agreemenl between estimated and experimental entropies.
文摘The paper introduces a method for displaying cubic volume cells (voxels) resulting frompartitioning given objectS with orthogonal planes for finite difference calculation. The method representS ablock of voxels as a B-rep solid model and conStrUcts the B-rep geometric clementS with an approach frombottom to up. Once the B-rep model is established, it is efficient in displaying because inner voxels areomitted and many coplanar facetS are merged together. By displaying the interSeCtion lines of theconstructed B-reP model and the partitioning planes, the tessellation image can be generated.
基金National Natural Science Foundation of China (No.59990470)
文摘In allusion to the deficient feature of product information in conceptualdesign, a framework of deficient information modeling for conceptual shape design is put forward,which includes qualitative shape modeling (a qualitative solid model), uncertain shape modeling (anuncertain relation model) and imprecise shape modeling (an imprecise region model). In theframework, the qualitative solid model is the core, which represents qualitatively (using symbols)the conceptual shapes of mechanical products. The uncertain relation model regarding domainrelations as objects and the imprecise region model regarding domains as objects are used to dealwith the uncertain and imprecise issues respectively, which arise from qualitative shape modeling orexist in product information itself.
文摘This paper creates 3D solid model and assembly of U RJ 92-6 oil tank and analyses its strength by integrated CAD/CAE/CAM software I-D EAS. Through integrated simulation in computer, design efficiency and quality of oil tank is greatly improved. Adopting integrated CAD/CAE/CAM software to carry out integrated research to equ ipment and products, we will be able to take overall analysis in aspects of 3-D solid modeling, pre-assembly and strength, etc., to realize non-paper designi ng and parallel designing. Problems can be found and settled during designing, w hich will increase designing efficiency and one-time success rate and realize o ptimum designing for products.
基金Supported by the National Natural Science Foundation of China(11471289,11162020)
文摘In this paper,we show that for any given planar cubic algebraic curves defined by a quadratic Hamiltonian vector field,we can always have their exact explicit parametric representations. We use a model of micro-structured solid to show an application of our conclusions.
文摘The report mainly studied the crawler frame motion platform to reduce weight and increase the intensity. Report described the structural design process which using CAD/CAE technology for solid modeling, simulation analysis, parameter optimization. And it also explained the outstanding advantages of CAD/CAE technology in mechanical design as well as simulation analysis.
文摘Ball-end mill is widely used in workpiece processi ng with free-form surfaces. Such models that can predict processing character istics precisely are very necessary to the aim of cost reducing, quality improvi ng and productivity progressing, the cutting force prediction is the most import ant among these models. To explore the physical essence of metal cutting, model researchers commonly simplify the geometric conditions in cutting process, and a ssume that the geometric parameters that are needed to solve the physical models have already been predefined, so it results in the separation between model res earch and practical application. In this paper, for the representative cutting f orce models of ball end milling, a new extraction method of geometric parameters is suggested, which makes it possible for physical model to actually serve for the practical manufacturing, and take in the inspection of real production.
基金Kampachi Farms LLC for their support to complete this work and for all the technical information provided to complete the numerical model
文摘In the present study, the dynamic response of a coupled SPM-feeder-cage system under irregular waves and shear currents is analyzed. A numerical model is developed by using the commercial software Orca Flex. Hydrodynamics coefficients of the vessel are calculated by using a 3D diffraction/radiation panel program. First- and second-order wave forces are included in the calculations. Morison equation is used to compute the drag force on line elements representing the net. Drag coefficients are determined at every time step in the simulation considering the relative normal velocity between the structural elements and the fluid flow. The dynamic response of the coupled system is analyzed for various environments and net materials. The results of the study show the effects of solidity ratio of the net and vertical positions of the cage on the overall dynamic response of the system, confirming the viability of this type of configuration for future development of offshore aquaculture in deep waters.
文摘The authors carried out drop impact tests for several soft materials under a flat frontal impact condition in which a drop hammer with a flat bottom surface strikes a plate-like soft material in the normal direction. The experimental results indicated that the impact force waveforms of soft materials consisted of a thorn-shaped waveform and a subsequent mountain-shaped waveform. The thorn-shaped waveform was strongly affected by the strain rate. In the present study, the occurrence mechanism of this distinctive waveform was discussed from the viewpoint of the viscosity transient phenomenon. A standard linear solid (SLS) model in which the viscosity transient phenomenon was considered was applied to the simulation. Some features of the impact force waveform of soft materials could be explained by the SLS model. Furthermore, the thorn-shape waveform could also be observed in the impact force waveforms of human skin and free-falling hollow balls.
基金supported by the National Key Research and Development Program of China(No.2017YFE9134700)the Natural Science Foundation of Zhejiang Province,China(No.LY22G010001)+3 种基金the Program of Humanities and Social Science of Education Ministry of China(No.20YJA630008)the Ningbo Natural Science Foundation of China(Nos.2021J235 and 2021J111)the Fund of Healthy&Intelligent Kitchen Engineering Research Center of Zhejiang Provincethe K.C.Wong Magna Fund in Ningbo University,China.
文摘In order to alleviate unstable factor-caused bifurcation and reduce oscillations in traffic flow,a feedback control with consideration of time delay is designed for the solid angle model(SAM).The stability and bifurcation condition of the new SAM is derived through linear analysis and bifurcation analysis,and then accurate range of stable region is obtained.In order to explore the mechanism of the influence of multiple parameter combinations on the stability of controlled systems,a definite integral stabilization method is provided to determine the stable interval of time delay and feedback gain.Numerical simulations are explored to verify the feasibility and effectiveness of the proposed model,which also demonstrate that feedback gain and delay are two key factors to alleviate traffic congestion in the SAM.