Physical and mechanical properties and microstructures of submarine soils in the Yellow Sea

In recent years,the exploration of seabed has been intensified,but the submarine soils of silt and sand in the Yellow Sea area have not been well investigated so far.In this study,the physical and mechanical properties of silt and sand from the Yellow Sea were measured using a direct shear apparatus and their microstructures were observed using a scanning electron microscope.The test results suggest that the shear strength of silt and sand increases linearly with the increase of normal stress.Based on the direct shear test,the scanning electron microscope was used to observe the section surface of sand.It is observed that the section surface becomes rough,with many“V”‐shaped cracks.Many particles appear on the surface of the silt structure and tend to be disintegrated.The X‐ray diffraction experiment reveals that the sand and silt have different compositions.The shear strength of sand is slightly greater than that of silt under high stress,which is related to the shape of soil particles and the mineral composition.These results can be a reference for further study of other soils in the Yellow Sea;meanwhile,they can serve as soil parameters for the stability and durability analyses of offshore infrastructure construction.

Physical,mechanical and thermal properties of vacuum sintered HUST-1 lunar regolith simulant

Establishing a base on the Moon is one of the new goals of human lunar exploration in recent years.Sintered lunar regolith is one of the most potential building materials for lunar bases.The physical,mechanical and thermal properties of sintered lunar regolith are vital performance indices for the structural design of a lunar base and analysis of many critical mechanical and thermal issues.In this study,the HUST-1 lunar regolith simulant(HLRS)was sintered at 1030,1040,1050,1060,1070,and 1080℃.The effect of sintering temperature on the compressive strength was investigated,and the exact value of the optimum vacuum sintering temperature was determined between 1040 and 1060℃.Then,the microstructure and material composition of vacuum sintered HLRS at different temperatures were characterized.It was found that the sintering temperature has no significant effect on the mineral composition in the temperature range of 1030-1080℃.Besides,the heat capacity,thermal conductivity,and coefficient of thermal expansion(CTE)of vacuum sintered HLRS at different temperatures were investigated.Specific heat capacity of sintered samples increases with the increase of test temperature within the temperature range from-75 to 145℃.Besides,the thermal conductivity of the sintered sample is proportional to density.Finally,the two temperatures of 1040 and 1050℃were selected for a more detailed study of mechanical properties.The results showed that compressive strength of sintered sample is much higher than tensile strength.This study reveals the effects of sintering temperature on the physical,mechanical and thermal properties of vacuum sintered HLRS,and these material parameters will provide support for the construction of future lunar bases.

Effect of Fe_(2)O_(3)on the Structure,Physical Properties and Crystallization of CaO-Al_(2)O_(3)-SiO_(2)Glass

The calcium aluminosilicate-based glasses(CaO-Al_(2)O_(3)-SiO_(2),CAS)with different Fe_(2)O_(3)content(0.10wt%,0.50wt%,0.90wt%,and 1.30wt%)were prepared by traditional melt-quenching method.The glass network structure,thermal and mechanical properties,and crystallization behavior changes were investigated by nuclear magnetic resonance spectrometer,Fourier-transform infrared spectro-photometer,X-ray diffractometer,differential scanning calorimetry and field emission scanning electron microscope measurements.The change of Q^(n)in glass structures reveals the glass network connectivity decreases due to the increasing content of Fe_(2)O_(3)addition,resulting in the increasing of non-bridging number in glass structure.The glass densities slightly rise from 2.644 to 2.681 g/cm^(3),while Vickers’s hardness increases at first,from 6.469 to 6.901 GPa,then slightly drops to 6.745 GPa,with Fe_(2)O_(3)content increase.There is almost no thermal expansion coefficient change from different Fe_(2)O_(3)content.The glass transmittance in visible range gradually decreases with higher Fe_(2)O_(3)content,resulting from the strong absorption of Fe^(2+)and Fe^(3+)ions.The calculated activation energy from thermal analysis results first decreases from 282.70 to 231.18 kJ/mol,and then increases to 244.02 kJ/mol,with the Fe_(2)O_(3)content increasing from 0.10wt%to 1.30wt%.Meanwhile,the maximum Avrami constant of 2.33 means the CAS glasses exhibit two-dimensional crystallization.All of the CAS glass-ceramics samples contain main crystal phase of anorthite,the microstructure appears lamellar and columnar crystals.

Physical-Rheological Properties and Performances of Rejuvenated(Styrene-Butadiene-Styrene)Asphalt with Polymerized-MDI and Aromatic Oil

Traditional asphalt rejuvenators,like aromatic oil(AO),are known to be effective in improving the low-temperature properties and fatigue performances of aged SBS(styrene-butadiene-styrene)modified asphalt(SBSMA)binders and mixtures.However,these rejuvenators inevitably compromise their high-temperature properties and deformation resistances because they dilute asphalt binder but do not fix the damaged structures of aged SBS.In this study,a highly-active chemical called polymerized 4,4-diphenylmethane diisocyanate(PMDI)was used to assist the traditional AO asphalt rejuvenator.The physical and rheological characteristics of rejuvenated SBSMA binders and the moisture-induced damage and rut deformation performances of corresponding mixtures were comparatively evaluated.The results showed that the increasing proportion of AO compromises the hightemperature property and hardness of aged SBSMA binder,and an appropriate amount of PMDI works to compensate such losses;3%rejuvenator at mass ratio of AO:PMDI=70:30 can have a rejuvenated SBSMA binder with a high-temperature performance similar to that of fresh binder,approximately at 71.4°C;the use of AO can help reduce the viscosity of PMDI rejuvenated SBSMA binder for improving its workability;PMDI can help improve the resistance of AO rejuvenated SBSMA binder to deformation,especially at elevated temperatures,through its chemical reactions with aged SBS;moisture induction can enhance the resistance to damage of rejuvenated mixtures containing AO/PMDI or only PMDI;and the rejuvenator with a mass ratio of AO:PMDI=70:30 can lead the rejuvenated mixture to meet the application requirement,with a rut depth of only 2.973 mm,although more PMDI can result in a higher resistance of rejuvenated mixtures to high-temperature deformation.

Physical and Chemical Properties of Horns Sheaths Particles for the Manufacture of Composite Materials

Salvaged cow horns from slaughterhouses have been transformed into fine particles for a physical characterization that has led us to determine the humidity rate (2.34% ± 0.054%), the actual density situated between 0.586 g/cm3 and 0.732 g/cm3, the swelling rate (12%), and one chemical characterization that permitted us to determine the rate of dry matters (97.05%), of mineral matters (2.5%), of protein matters (94.52%). From these weak values, it can easily be seen that cow horn case doesn’t absorb much water and improve the mechanical characteristics of the composite;the high rate of protein shows that keratin which is the structural molecule favors its gripping as reinforcing element in the manufacturing of composite materials.

Impacts of solid physical properties on the performances of a slurry external airlift loop reactor integrating mixing and separation

Solid physical properties are vital for the design, optimization, and scale-up of gas–liquid–solid multiphase reactors. The complex and interactional effects of the solid physical properties, including particle diameter, density, wettability, and sphericity, on the hydrodynamic behaviors in a new external airlift loop reactor(EALR) integrating mixing and separation are decoupled in this work. Two semi-empirical equations are proposed and validated to predict the overall gas holdup and liquid circulating velocity satisfactorily, and then the individual influence of such solid physical properties is further investigated. The results demonstrate that both the overall gas holdup in the riser and the liquid circulating velocity in the downcomer increase with the contact angle, but decrease with particle size, density, and sphericity.Additionally, the impact of the particle size on the liquid circulating velocity is also profoundly revealed on a micro-level considering the particle size distribution. Moreover, the axial solid concentration distribution is discussed, and the uniformity of the slurry is described by the mixing index of the solid particles. The results show that a more homogeneous mixture can be achieved by adding finer particles other than attaining violent turbulence. Therefore, this work lays a foundation for the design, scale-up, and industrialization of the EALRs.

Physical and emulsifying properties of pea protein:influence of combined physical modification by flaxseed gum and ultrasonic treatment

This study characterized and compared the physical and emulsifying properties of pea protein(PP)and its modified proteins(ultrasound treated-PP(PPU),flaxseed gum(FG)treated PP(PPFG)and ultrasound treated-PPFG(PPFGU)).The results showed FG triggered the formation of loosely attached complex with PP via physical modification under gentle magnetic stirring at pH 7.0,while ultrasound played an important role in reducing protein size,increasing surface hydrophobicity and molecular fluidity onto oil-water interface.So ultrasound further enhanced the interaction of PP with FG,and produced the PPFGU complex with smaller droplet size,higherζ-potential and lower turbidity.Further,combination of FG and ultrasound improved the physical properties of PP with higher viscosity,stiffer gels(defined as higher elastic modulus),stronger hydrophobic properties,better thermal stability,and fast protein absorption rate.Therefore,the PPFGU coarse emulsion performed highest emulsifying activity index(EAI)and emulsion stability index(ESI)that the stabilized nanoemulsion obtained smallest droplet size,higherζ-potential,and longest storage stability.The combination of FG and ultrasonic treatment will be an effective approach to improving the emulsifying property and thermal stability of PP,which can be considered as a potential plant-based emulsifier applied in the food industry.

Digital mapping of soil physical and mechanical properties using machine learning at the watershed scale

Knowledge about the spatial distribution of the soil physical and mechanical properties is crucial for soil management,water yield,and sustainability at the watershed scale;however,the lack of soil data hinders the application of this tool,thus urging the need to estimate soil properties and consequently,to perform the spatial distribution.This research attempted to examine the proficiency of three machine learning methods(RF:Random Forest;Cubist:Regression Tree;and SVM:Support Vector Machine)to predict soil physical and mechanical properties,saturated hydraulic conductivity(Ks),Cohesion measured by fall-cone at the saturated(Psat)and dry(Pdry)states,hardness index(HI)and dry shear strength(SS)by integrating environmental variables and soil features in the Zayandeh-Rood dam watershed,central Iran.To determine the best combination of input variables,three scenarios were examined as follows:scenarioⅠ,terrain attributes derivative from a digital elevation model(DEM)+remotely sensed data;scenarioⅡ,covariates of scenarioⅠ+selected climatic data and some thematic maps;scenarioⅢ,covariates in scenarioⅡ+intrinsic soil properties(Clay,Silt,Sand,bulk density(BD),soil organic matter(SOM),calcium carbonate equivalent(CCE),mean weight diameter(MWD)and geometric weight diameter(GWD)).The results showed that for Ks,Psat Pdry and SS,the best performance was found by the RF model in the third scenario,with R2=0.53,0.32,0.31 and 0.41,respectively,while for soil hardness index(HI),Cubist model in the third scenario with R2=0.25 showed the highest performance.For predicting Ks and Psat,soil characteristics(i.e.clay and soil SOM and BD),and land use were the most important variables.For predicting Pdry,HI,and SS,some topographical characteristics(Valley depth,catchment area,mltiresolution of ridge top flatness index),and some soil characteristics(i.e.clay,SOM and MWD)were the most important input variables.The results of this research present moderate accuracy,however,the methodology employed provides quick and costeffective information serving as the scientific basis for decision-making goals.

Differences of tuffaceous components dissolution and their impact on physical properties in sandstone reservoirs: A case study on Paleogene Wenchang Formation in Huizhou-Lufeng area, Zhu I Depression, Pearl River Mouth Basin, China

The element geochemical characteristics and diagenetic alteration products of tuffaceous components in sandstone reservoirs of Paleogene Wenchang Formation in typical subsags of the Huizhou-Lufeng area of the Zhu I Depression,Pearl River Mouth Basin,were identified through microscopic analysis and quantitative analysis of main and trace elements.The impacts of dissolution of different tuffaceous components on physical properties of reservoirs were discussed through quantitative characterization of reservoir physical properties.The results show that there are mainly four types of tuffaceous components in the study area,which are acidic,intermediate,basic and alkaline tuffaceous components.The acidic tuffaceous components evolved in a process of strong alteration and weak dissolution of alteration products,with a large amount of kaolinite precipitated during alteration to disenable the improvement of porosity and permeability.The intermediate and alkaline tuffaceous components evolved in a process of strong dissolution of tuffaceous components and strong alteration of residual tuffaceous components;the dissolution of tuffaceous components created intergranular pores,but the alteration products such as autogenic quartz,apatite and illite deteriorated the pore structure;ultimately,the dissolution of tuffaceous components resulted in the increase of porosity but no increase of permeability of the reservoir.The basic tuffaceous components dominantly evolved in a process of dissolution of tuffaceous components to strong dissolution of alteration products;both tuffaceous components between particles and laumontite generated from alteration can be strongly dissolved to create pores;thus,the dissolution of tuffaceous components can significantly increase the physical properties of the reservoir.

GIS-Based Assessment of Soil Chemical and Physical Properties as a Basis for Land Reclamation in Toshka Area, Aswan, EGYPT

The accurate assessment of soil properties is a crucial factor for composing and implementing reclamation plans. The main objective of this study was to evaluate soil chemical and physical properties and calculate the chemical and fertility index for assisting land reclamation in Toshka area. The Toshka area is located between latitudes 31°32'N and 31°36'N and longitudes 32°40'E and 32°60'E. GIS was used to select 16 sites. The results revealed the soil has undesirable characteristics. The soil pH ranged from slightly alkaline to moderately alkaline. Furthermore, it was characterized as saline (with a ECe of 4.65 - 11.45 dS⋅m−1) and moderately calcareous soil (with CaCO3 at 11.85% - 17.20%). The soil had a low soil organic matter content which did not exceed 0.18%. The soil was dominated by a sandy loam texture (62.50%) followed by a sandy clay loam texture (18.75%). The bulk density, total soil porosity and saturated hydraulic conductivity values varied with 1.38 - 1.55 Mg⋅cm−3, 41.85% - 48.45% and 1.20 - 3.34 cm⋅h−1, respectively. The chemical index ranged from low to moderate quality. The correlations between the parameters osculated between negative and positive. Therefore, the soil may be reclaimed if the soil properties are improved and crop selection is optimized for this soil.

Effects of cementation on physical properties of clastic rock-originated weathering crust reservoirs in the Kexia region,Junggar Basin,NW China

Cements are widely developed in clastic rock-originated weathering crust(CWC)reservoirs in the Kexia region along the northwestern margin of the Junggar Basin and significantly affect reservoir physical properties and oil and gas distribution in this area.Focusing on the CWC reservoirs at the top of both the Permian Jiamuhe Formation and the Triassic Karamay Formation,this study analyzed the types and characteristics of cements in the reservoirs and explored their effects on reservoir physical properties based on thin sections,SEM images,XRD results,and tests of physical properties.The main results are as follows.The cements in the CWC reservoirs in Kexia region mainly consist of carbonate minerals(41.5%),clay minerals(27.8%)and zeolite minerals(30%),as well as small amount of siliceous minerals.Among them,the carbonate minerals are dominated by siderite and calcite,the clay minerals mainly include kaolinite,interstratified illite/smectite(I/S)and chlorite,and the zeolite minerals primarily comprise heulandite and laumontite.These different types of multiphase cements are generally paragenetic or associated and affect reservoir physical properties to different degrees.Specifically,the carbonate and clay cements of the early diagenetic stage reduced the reservoirs’average porosity from 21%to 15%.The dissolution of some carbonate and zeolite cements in the early A substage of the middle diagenetic stage restored the average porosity to 18%,and the cementation in the late A substage decreased the average porosity to 13%again,of which about 4%was reduced by carbonate cements.The average porosity of the CWC reservoirs gradually decreased to the current value of approximately 10%in the B substage of the middle diagenetic stage.The impact of cementation on the CWC reservoirs can reach as far as 70 m below the unconformity.Moreover,the types and contents of cements vary with their depth below the unconformity surface,leading to the development of multiple zones with high cement content and the differentiated oil and gas distribution.

Physical and Mechanical Properties of Coral Sand in the Nansha Islands

Coral sand is a unique material developed in the tropical ocean environment, which is mainly composed of coral and other marine organism debris, with the CaCO3 content up to 96 %. It has special physical and mechanical properties due to its composition, structure and sedimentary environment. In this contribution, we discuss its specific gravity, porosity ratio compressibility, crushing, shearing and intensity for coral sand samples from the Nansha islands based on laboratory mechanical tests. Our results show distinct high porosity ratio, high friction angle and low intensity as compared with the quartz sand. We believe that grain crushing is the main factor that influences the deformation and strength of coral sand. Comprehensive study on the physical and mechanical properties of coral sands is significant in providing reliable scientific parameters to construction on coral islet, and thus avoids accidents in construction.

Effects of Material Physical Properties on White-rot Fungi Mycelial Growth

[ Objective] The research aimed to study effects of material physical properties on white-rot fungi mycelial growth and provide theoretical basis for further expanding the application range of white-rot fungi. [ Method Four common species of white-rot fungi were cultivated by wood meal fowl dung mixture in test tube and culture dishes. The relationship between physical properties of culture material and the growth of these mycelials were studied. [Result] The results showed the water retention capacity of culture material was decreased with the increasing of its grain size and porosity, but the decrease of its specific gravity reduced the material water retention. And the dehydration rate of medium prepared with these materials at the same moisture conditions tended to increase. These physical properties of material, such as grain size, specific gravity, porosity, water retention and water drainage, influenced the growth of white-rot fungi mycelial by affecting the moisture and ventilation condition of media. The results hinted that above material physical properties had feedback effects on the growth of white-rot fungi mycelia. [ Conclution] Physical properties of culture material have significant effects on the growth of white-rot fungi mycelial.

Changing Rules of Physical and Chemical Properties of Eucalyptus uraphylla spp. Forest at Different Ages in Southwest Yunnan Province

[Objective] The aim was to study on changing rules of physical and chemical properties of Eucalyptus uraphylla spp. forest at different ages in Southwest of Yunnan Province. [Method] In the research, field survey and laboratory analysis were adopted to study on physical and chemical properties of soils for the Eucalyptus uraphylla spp. at the first cutting ages in Lancang County. [Result] With the increasing of forest ages, for physical properties of soils, soil bulk density was increasing, and soil structure became poor; water contents in soils and capillary porosity were improving, but total soil porosity and non-capillary porosity were decreasing. For chemical properties, pH of soil dropped, but soil acidity improved; organic matter, total N, hydrolysable nitrogen, available phosphorus, and available potassium all declined; exchangeable Ca and Mg were improving due to fertilization and Ca and Mg lower consumption. The results showed that plays important roles in water absorption of soils and vegetation growth were improved with age increase by Eucalyptus uraphylla spp. forest, but ventilation and fertility declined accordingly. [Conclusion] The research indicated that dry branches and fallen leaves should be preserved and nutrient cycling should be protected during introduction and management of Eucalyptus uraphylla spp. to guarantee the nutrients in dry branches and leaves are back to soils, providing theoretical references for management of forest plantation and environment protection.

Research on thermal insulation materials properties under HTHP conditions for deep oil and gas reservoir rock ITP-Coring

Deep oil and gas reservoirs are under high-temperature conditions,but traditional coring methods do not consider temperature-preserved measures and ignore the influence of temperature on rock porosity and permeability,resulting in distorted resource assessments.The development of in situ temperaturepreserved coring(ITP-Coring)technology for deep reservoir rock is urgent,and thermal insulation materials are key.Therefore,hollow glass microsphere/epoxy resin thermal insulation materials(HGM/EP materials)were proposed as thermal insulation materials.The materials properties under coupled hightemperature and high-pressure(HTHP)conditions were tested.The results indicated that high pressures led to HGM destruction and that the materials water absorption significantly increased;additionally,increasing temperature accelerated the process.High temperatures directly caused the thermal conductivity of the materials to increase;additionally,the thermal conduction and convection of water caused by high pressures led to an exponential increase in the thermal conductivity.High temperatures weakened the matrix,and high pressures destroyed the HGM,which resulted in a decrease in the tensile mechanical properties of the materials.The materials entered the high elastic state at 150℃,and the mechanical properties were weakened more obviously,while the pressure led to a significant effect when the water absorption was above 10%.Meanwhile,the tensile strength/strain were 13.62 MPa/1.3%and 6.09 MPa/0.86%at 100℃ and 100 MPa,respectively,which meet the application requirements of the self-designed coring device.Finally,K46-f40 and K46-f50 HGM/EP materials were proven to be suitable for ITP-Coring under coupled conditions below 100℃ and 100 MPa.To further improve the materials properties,the interface layer and EP matrix should be optimized.The results can provide references for the optimization and engineering application of materials and thus technical support for deep oil and gas resource development.

Rock physical characteristics of deep dolomite under complex geological conditions:A case study of 4th Member of Sinian Dengying Formation in the Sichuan Basin,China

The deep-ultra deep carbonate reservoir in China,commonly subjected to modification of multi-stage diagenesis,has extremely high heterogeneity.Conventional rock physics analysis cannot accurately identify the elastic responses of reservoir.Here,the rock physics properties of the dolomite from the 4th Member of the Sinian Dengying Formation are experimentally measured,and the change law of rock physics characteristics is investigated within the framework of the diagenetic processes by the analysis of the elastic and petrologic characteristics,pore structure,and sedimentary environments.The results show that the differentiated diagenesis results in different pore structure characteristics and microtexture characteristics of the rock.The microbial dolomite of the algal mound-grain beach facies is subjected to the contemporaneous microbial dolomitization and seepage-reflux dolomitization,penecontemporaneous selective dissolution,burial dolomitization,and hydrothermal dolomitization.The resultant crystalline dolomite is found with one main type of the dolomite crystal contact boundaries,and the dissolution pore is extensive development.The siliceous,muddy,and limy dolomite of the interbeach sea environment mainly experiences the weak capillary concentration dolomitization,intensive mechanical compaction-induced densification,and burial dolomitization.Such crystalline dolomite is observed with four types of contact boundaries,namely the dolomite contact,clay contact,quartz contact,and calcite contact boundaries,and porosity mostly attributed to residual primary inter-granular or crystalline pores.The samples with the same crystal boundary condition have consistent correlations between the compressional-and shear-wave velocities,and between the compressional-wave velocity and the velocity ratio.Additionally,the variation of the acoustic velocity with effective pressure and the intensity of pore-scale fluid-related dispersion are controlled by the differentiation of pore structure types of the samples.The varied effects of soft pores like micro-cracks on the compressional-and shearwave velocity causes considerable changes in the relationships between the compressional-and shearwave velocities,compressional-wave velocity and velocity ratio,and porosity and acoustic velocity.This research is an attempt to demonstrate a novel method for investigating the rock physics variation of rock during the geological process,and the obtained findings can provide the rock physics basis for seismic prediction of the characteristics of deep carbonate reservoirs.

Quantitative characterizations of anisotropic dynamic properties in organic-rich shale with different kerogen content

Understanding the quantitative responses of anisotropic dynamic properties in organic-rich shale with different kerogen content(KC)is of great significance in hydrocarbon exploration and development.Conducting controlled experiments with a single variable is challenging for natural shales due to their high variations in components,diagenesis conditions,or pore fluid.We employed the hot-pressing technique to construct 11 well-controlled artificial shale with varying KC.These artificial shale samples were successive machined into prismatic shape for ultrasonic measurements along different directions.Observations revealed bedding perpendicular P-wave velocities are more sensitive to the increasing KC than bedding paralleling velocities due to the preferential alignments of kerogen.All elastic stiffnesses except C_(13)are generally decreasing with the increasing KC,the variation of C_(1) and C_(33)on kerogen content are more sensitive than those of C_(44)and C_(66).Apparent dynamic mechanical parameters(v and E)were found to have linear correlation with the true ones from complete anisotropic equations independent of KC,which hold value towards the interpretation of well logs consistently across formations,Anisotropic mechanical parameters(ΔE and brittlenessΔB)tend to decrease with the reducing KC,withΔB showing great sensitivity to KC variations.In the range of low KC(<10%),the V_(P)/V_(S) ratio demonstrated a linearly negative correlation with KC,and the V_(P)/V_(S) ratio magnitude of less than 1.75may serve as a significant characterization for highly organic-rich(>10%)shale,compilation of data from natural organic rich-shales globally verified the similar systematic relationships that can be empirically used to predict the fraction of KC in shales.

Preparation of Manganese Oxide and Its Adsorption Properties

The in-situ oxidation of manganese sulfate solution with H2O_(2),sodium hypochlorite,potassium permanganate and oxygen as oxidants was investigated by means of SEM,EDS,XRD,BET and infrared analysis,and the effects of different oxidants on the morphology,phase composition,surface properties and specific surface area of manganese oxides were investigated.The experimental results show that the diameter of manganese oxide particles prepared with H_(2)O_(2)is the smallest,about 50 nm,and the specific surface area is the largest,63.8764 m^(2)/g.It has the advantages of abundant surface hydroxyl groups,no introduction of other impurities and large adsorption potential.It is most suitable to be used as an oxidant for oxidizing manganese sulfate solution to prepare manganese oxide by in-situ oxidation.Nano manganese oxide prepard by H_(2)O_(2)in-situ oxidation method is used as adsorbent to adsorb cobalt and nickel impurities in manganese sulfate.When the reaction pH is 6,the reaction time is 30min and the amount of adsorbent is 1.0 g,the adsorption rates of cobalt and nickel impurities in 100ml manganese sulfate solution are 97.59%and 97.67%,respectively.The residual amounts of cobalt and nickel meet the industrial process standard of first-class products(Co,Ni w/%≤0.005)of high-purity manganese sulfate(Hg/t4823-2015)for batteries.The study plays a guiding role in the preparation and regulation of manganese oxide,and provides a new method with high efficiency,purity and adsorbent availability for the preparation of high-purity manganese sulfate solution.

Vertical Variation Characteristics of Basic Physical Properties in the Daxia Irrigated Area of Qinghai Province

Influenced by climate, biology and soil properties, vertical soil profile showed stratification character in terms of basic physical properties. The research conducted measurement and analysis on basic physical properties of typical field in the Daxia irrigation area in Qinghai Province. The results showed that soil bulk density changed from decreasing to increasing upon soil horizon; the soil horizons in 0-40 and 90-150 cm were high porosity zones, and the others were low porosi- ty area; the saturation moisture capacity, water retention of capillary porosity and field water retention all changed from decreasing to increasing upon soil horizon featured by arithmetic progression. In addition, the research area in Daxia irrigated area showed loose structure in soil horizon of 0-40 cm, compacted in 40-60 cm, and loose again in 60-200 cm vertically.

Soil Physical and Chemical Properties of Five Subtropical Forests in Lingao of Hainan

With 5 types of typical forests as research object, the physical and chemical properties of different types of forests were analyzed by sample plot investigation method. The results showed that： the soil total porosity was the highest in the Casuarina equisetifolia forest （46.168%）, but the lowest in the Encalyptus robusta forest （39.46%）. The soil capillary porosity was the highest in the Acacia mangium forest （22.57%）, but the lowest in the secondary forest （18.95%）. The soil water content was the highest in the C. equisetifolia forest, with a mean value of 27.85%, but the lowest in the secondary forest, with a mean value of 4.34%. The soil pH values were in the range of 4.81-6.59, the soils in the A. mangium forest, C. equisetifolia forest and E. robusta forest were strongly acidic （pH 4.5-5.5）, and the soils in the secondary forest and C. nucifera forest were weakly acidic. The soils had organic matter contents in the range of 0.34-28.68 g/kg, and showed an order of A. mangium forest〉C. equisetifolia forest〉E. robusta forest〉secondary forest〉C. nucifera forest, with a decreasing trend with the soil depth increasing. The soil total N contents were in the range of 0.10-1.63 g/kg, the A. mangium forest showed the highest soil total N contents, while the C. nucifera forest exhibited the lowest soil total N contents; the soil total P contents were in the range of 0.21-1.74 g/kg, and the E. robusta forest had the highest soil total P contents; and the soil total K contents were in the range of 0.16-2.15 g/kg, and the A. mangium forest exhibited the highest soil total K contents. The soil available P contents were in the range of 0.98-132.46 mg/kg; and the secondary forests had the highest soil available P contents; and the soil rapidly available K contents were in the range of 3.03-27.35 mg/kg, and the C. nucifera forest exhibited the highest soil rapidly available K contents. The soil ammonium N contents were in the range of 1.38-5.15 mg/kg, and the nitrate N contents were in the range were in the range of 0.56 -3.51 mg/kg. The A. mangium forest showed the highest soil nitrate N contents （with a mean value of 2.29 mg/kg） and ammonium N contents （with a mean value of 3.93 mg/kg）. For the same forest type, with the increase of soil depth, the nitrate nitrogen and ammonium nitrogen content also showed a decreasing trend.