Extractive distillation(ED)and solvent-assisted pressure-swing distillation(SA-PSD)are both special distillation processes that perform good at separating pressure-insensitive azeotropes.However,few reported studies h...Extractive distillation(ED)and solvent-assisted pressure-swing distillation(SA-PSD)are both special distillation processes that perform good at separating pressure-insensitive azeotropes.However,few reported studies have compared the performance of the two processes.In this paper,ED processes with N-methylpyrrolidone(NMP)and dimethlac-etamide(DMCA)as entrainer,SA-PSD process with isopropyl-alcohol(IPA)as solvent and SA-PSD process with partial heat integration(PHI-PSD)are proposed to achieve high purity separation of a mixture of cyclohexane/2-butanol system.The optimal operating conditions of the processes are obtained after optimizing with NSGA-Ⅱ algorithm when total annual cost(TAC)and the entropy production of process are set as objectives.The optimal results show that the optimal PHI-PSD process has lower TAC by 28.7% and the lower entropy production by 39.5% than the optimal SA-PSD process while the ED process with NMP as entrainer has lower TAC by 50.9% and the lower entropy production by 56.1% than the optimal SA-PSD process.The optimal results show that the ED process with NMP as entrainer has the best economic and thermodynamic efficiency among the four proposed processes in this paper.展开更多
Microstructures were produced on curved surfaces and micro-protrusions by using direct micromolding with fourthermoplastic polymers. This method is simpler and more convenient than micromolding with liquid prepolymer ...Microstructures were produced on curved surfaces and micro-protrusions by using direct micromolding with fourthermoplastic polymers. This method is simpler and more convenient than micromolding with liquid prepolymer or using theμTM method. By repeated molding, crossed structures were produced with a stamp prepared only with lines. The processingvariables including the softening temperature of the polymers and heating time were discussed. The result shows that theoptimal molding temperature is preferably slightly higher than the melting temperature of the thermoplastic polymers, atwhich polymers are in the critical states of being melted. This method can be applied to many polymers except those with high softening temperatures or high rate of shrinkage upon temperature change.展开更多
基金supported by the National Natural Science Foundation of China(22178030,21878025,22078026)。
文摘Extractive distillation(ED)and solvent-assisted pressure-swing distillation(SA-PSD)are both special distillation processes that perform good at separating pressure-insensitive azeotropes.However,few reported studies have compared the performance of the two processes.In this paper,ED processes with N-methylpyrrolidone(NMP)and dimethlac-etamide(DMCA)as entrainer,SA-PSD process with isopropyl-alcohol(IPA)as solvent and SA-PSD process with partial heat integration(PHI-PSD)are proposed to achieve high purity separation of a mixture of cyclohexane/2-butanol system.The optimal operating conditions of the processes are obtained after optimizing with NSGA-Ⅱ algorithm when total annual cost(TAC)and the entropy production of process are set as objectives.The optimal results show that the optimal PHI-PSD process has lower TAC by 28.7% and the lower entropy production by 39.5% than the optimal SA-PSD process while the ED process with NMP as entrainer has lower TAC by 50.9% and the lower entropy production by 56.1% than the optimal SA-PSD process.The optimal results show that the ED process with NMP as entrainer has the best economic and thermodynamic efficiency among the four proposed processes in this paper.
基金supported by the National Natural Science Foundation of China(No.20374049)the Specialized Research Pund for the Doctoral Program of Higher Education(20040358018).
基金This work was financially supported by the National Natural Science Foundation of China (No. 20174038).
文摘Microstructures were produced on curved surfaces and micro-protrusions by using direct micromolding with fourthermoplastic polymers. This method is simpler and more convenient than micromolding with liquid prepolymer or using theμTM method. By repeated molding, crossed structures were produced with a stamp prepared only with lines. The processingvariables including the softening temperature of the polymers and heating time were discussed. The result shows that theoptimal molding temperature is preferably slightly higher than the melting temperature of the thermoplastic polymers, atwhich polymers are in the critical states of being melted. This method can be applied to many polymers except those with high softening temperatures or high rate of shrinkage upon temperature change.
基金IV. ACKN0WLEDGMENT This work was supported by the National Natural Science Foundation of China （No.20374049） and the Specialized Research Foundation for the Doctoral Program of Higher Education （20040358018）.
