The Al_(2)O_(3)and Mn/Al_(2)O_(3)sorbents highly utilized in destructive sorption of NF_(3)

NF_(3)is commonly used as an etching and cleaning gas in semiconductor industry,however it is a strongly greenhouse gas.Therefore,the destruction of disposal NF_(3)is an urgent task to migrate the greenhouse effect.Among the technologies for NF_(3)abatement,the destructive sorption of NF_(3)over metal oxides sorbents is an effective way.Thus,the search for a highly reactive and utilized sorbent for NF_(3)destruction is in great demand.In this work,AlOOH supported on carbon-sphere(AlOOH/CS)as precursors were synthesized hydrothermally and heat-treated to prepare the Al_(2)O_(3)sorbents.The influence of AlOOH/CS hydrothermal temperatures on the reactivity of derived Al_(2)O_(3)sorbents for NF_(3)destruction was investigated,and it is shown that the Al2O3 from AlOOH/CS hydro-thermalized at 120℃is superior to others.Subsequently,the optimized Al_(2)O_(3)was covered by Mn(OH)x to prepare Mn/Al_(2)O_(3)sorbents via changing hydrothermal temperatures and Mn loadings.The results show that the Mn/Al_(2)O_(3)sorbents are more utilized than bare Al_(2)O_(3)in NF_(3)destructive sorption due to the promotional effect of Mn_(2)O_(3)as surface layer on the fluorination of Al_(2)O_(3)as substrate,especially the optimal 5%Mn/Al2O3(160℃)exhibits a utilization percentage as high as 90.4%,and remarkably exceeds all the sorbents reported so far.These findings are beneficial to develop more efficient sorbents for the destruction of NF_(3).

Effect of Ca/Mg molar ratio on the calcium-based sorbents

Steelmaking industry faces urgent demands for both steel slag utilization and CO_(2)abatement.Ca and Mg of steel slag can be extracted by acid solution and used to prepare sorbents for CO_(2)capture.In this work,the calcium-based sorbents were prepared from stainless steel slag leachate by co-precipitation,and the initial CO_(2)chemisorption capacity of the calcium-based sorbent prepared from steel slag with the Ca and Mg molar ratio of 3.64:1 was 0.40 g/g.Moreover,the effect of Ca/Mg molar ratio on the morphology,structure,and CO_(2)chemisorption capacity of the calcium-based sorbents were investigated.The results show that the optimal Ca/Mg molar ratio of sorbent for CO_(2)capture was4.2:1,and the skeleton support effect of MgO in calcium-based sorbents was determined.Meanwhile,the chemisorption kinetics of the sorbents was studied using the Avrami-Erofeev model.There were two processes of CO_(2)chemisorption,and the activation energy of the first stage(reaction control)was found to be lower than that of the second stage(diffusion control).

Studies of Adsorption of Cadmium Ions by Biowaste Adsorbent from Aqueous Solutions with Ion-Selective Electrodes and ICP-OES

Using environment-friendly and low-cost biowaste adsorbents as toxic metal ion removal substrates from aqueous solutions has a great economic advantage. This work evaluated pumpkin and potato peel biowastes for the adsorption of cadmium ions. The biowastes were treated with acid or base. Batch experiments were carried out by introducing a known concentration of metal ion solution into the biowaste sorbent at various pH levels. The pH and metal ion concentration was monitored with pH and cadmium ion-selective electrode continuously for two hours, and the final concentration for the metal ion after 24 hours was measured with the cadmium electrode and then confirmed with ICP-OES. L-type isotherms were obtained that fit to Freundlich model. Adsorption isotherms showed chemical adsorption and the kinetics following the second order model. Equilibrium adsorption capacity is higher than 29 mg/g at pH 5.6 when the initial concentration is 220 ppm. Dynamic cadmium adsorption capacity is 17 mg/g from aqueous solution when the feed solution is 220 ppm with pumpkin peel biowaste sorbent. The biowaste materials can be regenerated with acid washing.

CO_(2) capture by double metal modified CaO-based sorbents from pyrolysis gases

High-temperature pyrolysis technology can effectively solve the problem of municipal solid waste pollution.However,the pyrolysis gas contains a large amount of CO_(2),which would adversely affect the subsequent utilization.To address this problem,a novel method of co-precipitation modification with Ca,Mg and Zr metals was proposed to improve the CO_(2)capture performance.X-ray diffraction(XRD)patterns and energy dispersive X-ray spectroscopy analysis showed that the two inert supports MgO and CaZrO_(3)were uniformly distributed in the modified calcium-based sorbents.In addition,the XRD results indicated that CaZrO_(3)was produced by the reaction of ZrO_(2)and CaO at high temperatures.The effects of doping ratios,adsorption temperature,calcination temperature,CO_(2)concentration and calcination atmosphere on the adsorption capacity and cycle stability of the modified calcium-based sorbent were studied.The modified calcium-based sorbent achieved the best CO_(2)capture performance when the doping ratio was 10:1:1 with carbonation at 700℃ under 20%CO_(2)/80%N_(2)atmosphere and calcination at 900℃ under100%N_(2)atmosphere.After ten cycles,the average carbonation conversion rate of Ca-10 sorbent was 72%.Finally,the modified calcium-based sorbents successfully reduced the CO_(2)concentration of the pyrolysis gas from 37%to 5%.

Combination of Sorbents and Modification of Its Constituents to Enhance the Mopping Ability of Chemically Modified and Unmodified Biological Wastes on Crude Oil and Its Lower Fractions

Protein wastes (feathers, goat hair) and cellulosic wastes (corn cob, coconut husks) were collected, washed with detergent solution, thoroughly rinsed and sun dried for 2 days before drying in an oven and then ground, half of ground material was carbonized at a maximum temperature of 500?C after mixing with H2SO4.The carbonized parts were pulverized;both carbonized and uncarbonized sorbents were sieved into two particle sizes of 325 μm and 625 μm using mechanical sieve.1.5 g protein wastes and cellulosic wastes were each used to mop up spilled crude oil, diesel, kerosene and petrol (separately before combining) by encasing them in a sac like boom of 2cm x 2cm x 1cm dimension so as to determine the efficacy of waste sorbents in cleaning hydrocarbon spills. Results of Tables 1(a)-4(a), 1(b)-4(b) and 5-8 shows that the sorbents mopped, desorbed and retained an average of more than 500%, 350% and 300% of their weight of the hydrocarbon sorbates within average of 90 mins contact time, the volume of sorbates mopped up increased significantly when equal weight of activated and unactivated sorbents were combined, the results of equal combination of activated and unactivated sorbents at each particle size and contact time were compared with that of calculated values, high percentage retention observed were a function of mechanism of absorption/adsorption. Each sorbent have a distinct feature that enhances its mopping ability. Large volumes of the hydrocarbon liquids were recovered by mere pressing, the sorbates were mopped up in the order;crude oil > diesel > kerosene > petrol. Protein sorbents with oleophilic and aqua phobic properties absorbed more of all the hydrocarbon liquids than cellulosic sorbents at any particle size and contact, the later tend to be more abundant and therefore cost effective;it was observed that both carbonized and uncarbonized sorbents are good hydrocarbon mops and therefore good alternative to synthetic polyurethane foam already in use. Combination, particle size, activation of sorbents, contact time, viscosity and chain length of hydrocarbon determined the amount of sorbates absorbed/adsorbed, recovered or retained. The residual leachable oil (kerosene) in the sorbents were below 5% and does not constitute serious environmental menace when left in an open dump to decay being biodegradable waste, but a brighter application is that the waste sorbent can be used in making logs as alternative to fire wood or in making particle board for furniture.

Preparation and utilization of wheat straw anionic sorbent for the removal of nitrate from aqueous solution

In order to reduce the impact of eutrophication caused by agricultural residues （i.e., excess nitrate） in aqueous solution, economic and effective anionic sorbents are required. In this article, we prepared anionic sorbent using wheat straw. Its structural characteristics and adsorption properties for nitrate removal from aqueous solution were investigated. The results indicate that the yield of the prepared anionic sorbent, the total exchange capacity, and the maximum adsorption capacity were 350%, 2.57 mEq/g, and 2.08 mmol/g, respectively. The Freundlich isotherm mode is more suitable than the Langmuir mode and the adsorption process accords with the first order reaction kinetic rate equation. When multiple anions （SO4^2-, H2PO4^-, NO3^-, and NO2^-） were present, the isotherm mode of prepared anionic sorbent for nitrate was consistent with Freundlich mode; however, the capacity of nitrate adsorption was reduced by 50%. In alkaline solutions, about 90% of adsorbed nitrate ions could be desorbed from prepared anionic sorbent. The results of this study confirmed that the wheat straw anionic sorbent can be used as an excellent nitrate sorbent that removes nitrate from aqueous solutions.

Recent progress of amine modified sorbents for capturing CO2 from flue gas

Under the Paris agreement, China has committed to reducing CO_2 emissions by 60%–65% per unit of GDP by 2030.Since CO_2 emissions from coal-fired power plants currently account for over 30% of the total carbon emissions in China, it will be necessary to mitigate at least some of these emissions to achieve this goal. Studies by the International Energy Agency(IEA) indicate CCS technology has the potential to contribute 14% of global emission reductions, followed by 40% of higher energy efficiency and 35% of renewable energy, which is considered as the most promising technology to significantly reduce carbon emissions for current coal-fired power plants.Moreover, the announcement of a Chinese national carbon trading market in late 2017 signals an opportunity for the commercial deployment of CO_2 capture technologies.Currently, the only commercially demonstrated technology for post-combustion CO_2 capture technology from power plants is solvent-based absorption. While commercially viable, the costs of deploying this technology are high. This has motivated efforts to develop more affordable alternatives, including advanced solvents, membranes,and sorbent capture systems. Of these approaches, advanced solvents have received the most attention in terms of research and demonstration. In contrast, sorbent capture technology has less attention, despite its potential for much lower energy consumption due to the absence of water in the sorbent. This paper reviews recent progress in the development of sorbent materials modified by amine functionalities with an emphasis on material characterization methods and the effects of operating conditions on performance. The main problems and challenges that need to be overcome to improve the competitiveness of sorbent-based capture technologies are discussed.

Impact of impregnation pressure on desulfurization performance of Zn-based sorbents supported on semi-coke

High-pressure impregnation, a new preparation method for sorbents to remove H2S from hot coal gas, is introduced in this paper. Semi-coke （SC） and ZnO is selected as the support and active component of sorbent, respectively. The sorbent preparation process includes high-pressure impregnation, filtration, ovendry and calcination. The aim of this research is to primarily study the effects of the impregnation pressure on physical properties and desulfurization ability of the sorbent. The desulfurization experiment was carried out in a fixed-bed reactor at 500 ~C and a simulated coal gas used in this work was composed of CO （33 vol%）, H2 （39 vol%）, H2S （300 ppm in volume）, and N2 （balance）. Experimental results show that the pore structure of the SC support can be improved effectively and ZnO active component can be uniformly dispersed on the support, with the small particle size of 10-500 nm. Sorbents prepared using high-pressure impregnation have better desulfurization capacity and their active components have higher utilization rate. P20-ZnSC sorbent, obtained by high-pressure impregnation at 20 atm, has the best desulfurization ability with a sulfur capacity of 7.54 g S/100g sorbent and a breakthrough time of 44 h. Its desulfurization precision and efficiency of removing H2S from the middle temperature gases can reach 〈 1 ppm and 〉99.7%, respectively, before sorbent breakthrough.

Desulfurization kinetics of ZnO sorbent loaded on semi-coke support for hot coal gas

Zn-based sorbent （Z20SC） prepared through semi-coke support in 20 wt% zinc nitrate solution by high-pressure impregnation presents an excellent desulfurization capacity in hot coal gas,in which H2 S can not be nearly detected in the outlet gas before 20 h breakthrough time.The effects of the main operational conditions and the particle size of Z20SC sorbent on its desulfurization performances sorbent were investigated in a fixed-bed reactor and the desulfurization kinetics of Z20SC sorbent removing H2 S from hot coal gas was calculated based on experimental data.Results showed that the conversion of Z20SC sorbent desulfurization reaction increased with the decrease of the particle size of the sorbent and the increases of gas volumetric flow rate,reaction temperature and H 2 S content in inlet gas.Z20SC sorbent obtained from hydrothermal synthesis by high-pressure impregnation possessed much larger surface area and pore volume than semi-coke support,and they were significantly reduced after the desulfurization reaction.The equivalent grain model was reasonably used to analyze experimental data,in which k s=4.382×10-3 exp（-8.270×103/RgT） and Dep=1.262×10-4exp（1.522×104/RgT）.It suggests that the desulfurization reaction of the Z20SC sorbent is mainly controlled by the chemical reaction in the initial stage and later by the diffusion through the reacted sorbent layer.

Bench-Scale Testing of Zinc Ferrite Sorbent for Hot Gas Clean-up

Advanced integrated gasification combined cycle （IGCC） power generation systems require the development of high-temperature, regenerable desulfurization sorbents, which are capable of removing hydrogen sulfide from coal gasifier gas to very low levels. In this paper, zinc ferrites prepared by co-precipitation were identified as a novel coal gas desulfurization sorbent at high temperature. Preparation of zinc ferrite and effects of binders on pore volume, strength and desulfurization efficiency of zinc ferrite desulfurizer were studied. Moreover, the behavior of zinc ferrite sorbent during desulfurization and regeneration under the temperature range of 350-400 ℃ are investigated. Effects of binders on the pore volume, mechanical strength and desulfurization efficiency of zinc ferrite sorbents indicated that the addition of kaolinite to zinc ferrite desulfurizer seems to be superior to other binders under the experimental conditions.

Effects of ultrasound on the desulfurization performance of hot coal gas over Zn-Mn-Cu supported on semi-coke sorbent prepared by high-pressure impregnation method

Zn-Mn-Cu/SC（U） sorbent was hydrothermally synthesized by ultrasound-assisted high-pressure impregnation method with semi-coke（SC）as support and the mixed solution of zinc nitrate,manganese nitrate and copper nitrate as active component precursors.The desulfurization performances of hot coal gas on the prepared sorbent at a mid-temperature of 500°C were tested in fixed-bed reactor.Morphology and pore structure of the prepared sorbent were also characterized by TEM,N2adsorption/desorption isotherms and XRD.For comparison,the sorbent of Zn-Mn-Cu/SC prepared by conventional high-pressure impregnation was also evaluated and characterized in order to study the effects of ultrasound treatment.Zn-Mn-Cu/SC（U） sorbent prepared by high-pressure impregnation under ultrasound-assisted condition showed a better desulfurization performance than Zn-Mn-Cu/SC.It could remove H2 S from 1000×10-6m3/m3 to 0.1×10-6m3/m3 at 500°C and maintained for 12.5 h with the sulfur capacity of 7.74%,in which both the breakthrough time and sulfur capacity were about 32% and 51% higher than those of Zn-Mn-Cu/SC sorbent.The introduction of ultrasound during high-pressure impregnation process greatly improved the morphology and pore structure of the sorbent.The ultrasonic treatment made particle size of active components smaller and made them more evenly disperse on semi-coke support,which provided more opportunities to contact with H2S in coal-based gases.However,there were no any difference in compositions and existing forms of active components on the Zn-Mn-Cu/SC and Zn-Mn-Cu/SC（U） sorbents.

Study on Zn_2SiO_4 Formation Kinetics and Activity Stability of Desulfurization Sorbent

A new industrial S Zorb sorbent(Ni/Zn O-P) was prepared by using the spray drying technique. The other two traditional sorbents(Ni/Zn O-M and Ni/Zn O-H) were prepared in exactly the same way except the use of different silica-alumina binder matrices. The XRD, Rietveld quantitative phase analysis, BET, and laser particle size analysis were employed to characterize their physico-chemical properties. The deactivation mechanism and desulfurization kinetics of sorbent was investigated on a water vapor aging treatment device. It was shown that both the water vapor pressure and reaction temperature significantly could influence the formation rate of inactive Zn2 Si O4, which could decrease the sulfur storage capacity of sorbents. The Zn2 Si O4 content profiles could be fitted into the zero order equation, from which the apparent rate constant k and the activation energy E a were calculated. The matrix P greatly raised the E a of Zn2 Si O4 formation due to the less bridged hydroxyl silanol groups on its surface, which accounted for the high stability of Ni/Zn O-P. The desulfurization performance of the fresh and aged sorbents showed that the overall average sulfur conversion of Ni/Zn O-P(aged) was 92%, which was close to that of fresh sorbents(95%), and was higher than that of Ni/Zn O-M(aged)(86%) and Ni/Zn O-H(aged)(90%). Based on these findings, the application of Ni/Zn O-P can greatly improve the long-term running stability of the industrial unit.

Effect of impregnation methods on sorbents made from lignite for desulfurization at middle temperature

With lignite after vacuum drying as the raw material,a series of Zn-based sorbents were prepared by static impregnation,ultrasonic-assisted impregnation,bubbling-assisted impregnation and high-pressure impregnation.The physical properties and the desulfurization performances of Zn-based sorbents were studied systematically by XRD,BET,AAS characterization techniques and the fixed-bed desulfurization evaluation apparatus.The sorbents obtained by high-pressure impregnation method have a larger specific surface area,pore volume and pore diameter comparing with other methods,which is conducive to the sulfidation reaction of hydrogen sulfide gas in the sorbent.The effects of pressure during the high-pressure impregnation and concentration of Zn(NO3)2 precursor solution on the sorbents properties and desulfurization behavior were investigated.The higher the impregnation pressure and the concentration of impregnation solution are,the greater the amount of the active components are uploaded.However,overhigh impregnation pressure can cause collapse and blocking of the carrier pore.The optimal operating condition of high-pressure impregnation method for preparing the sorbents was the impregnation pressure of 20 atm and the solution concentration of 41%.Under that condition,the sorbent had the best desulfurization ability with a sulfur capacity of 13.94 gS/100 gsorbent and a breakthrough time of 54 h.Its desulfurization precision and efficiency of removing H2S before sorbent breakthrough from the middle temperature gases of 400℃ can reach【5 ppm and】99%,respectively.Sorbents could be regenerated under the condition of 1 vol%O2,20 vol% H2O,0.5 vol% NH3,and N2balance gas.The regenerated sorbent could be used for repeated absorption of H2S with a slight decrease in desulfurization effect.

CO2 capture over molecular basket sorbents:Effects of SiO2 supports and PEG additive

The objective of this work is to study the influences of silica supports and PEG additive on the sorption performance of molecular basket sorbent（MBS） for COcapture consisting of polyethylenimine and one of the following supports: SBA-15（2-D structure）, TUD-1（3-D sponge-like structure） and fumed silica HS-5（3-D disordered structure）. Effects of the supports regarding pore structures and pore properties, the PEI loading amount as well as the sorption temperature were examined. Furthermore, polyethylene glycol（PEG） was introduced as an additive into the sorbents and its effect was investigated at different PEI loadings and sorption temperatures. The results suggest that the pore properties of MBS（after PEI loading） play a more important role in the COsorption capacity, rather than those of the supports alone.MBS with 3D pore structure exhibits higher COsorption capacity and amine efficiency than those with 2D-structured support. Among the sorbents studied, fumed silica（HS-5） based MBS showed the highest COsorption capacity in the temperature range of 30-95 °C, probably due to its unique interstitial pores formed by the aggregation of polymer-loaded SiOparticles. It was found that the temperature dependence is directly related to the PEI surface coverage layers. The more PEI surface coverage layers, the higher diffusion barrier for COand the stronger temperature dependence of COcapacity. 3D MBS exceeds 2D MBS at the same PEI coverage layers due to lower diffusion barrier. Adding PEG can significantly enhance the COsorption capacity and improve amine efficiency of all MBS, most likely by alleviating the diffusion barrier within PEI bulk layers through the inter-molecular interaction between PEI and PEG.

A fibrous hypercrosslinked sorbent prepared on PP-ST-DVB matrix via post-crosslinking reaction

A fibrous sorbent possessing abundant micropore structure was firstly prepared via post-crosslinking reaction on the PP-ST-DVB original fiber. Its micromorphology and sorptive properties were investigated, and the results demonstrated that the novel fibrous hypererosslinked sorbent has narrow pore-size distribution, small average porous radius （1.90 nm）, high specific surface area （362.31 m^2/g）, and fine sorptive properties for small organic molecules.

Supported ionic liquid sorbents for CO_2 capture from simulated flue-gas

Supported ionic liquid(IL) sorbents for CO_2 capture were prepared by impregnating tetramethylammonium glycinate([N1111][Gly]) into four types of porous materials in this study. The CO_2 adsorption behavior was investigated in a thermogravimetric analyzer(TGA). Among them, poly(methyl methacrylate)(PMMA)-[N1111][Gly]exhibits the best CO_2 adsorption properties in terms of adsorption capacity and rate. The CO_2 adsorption capacity reaches up to 2.14 mmol·g-1 sorbent at 35 °C. The fast CO_2 adsorption rate of PMMA-[N1111][Gly] allows 60 min of adsorption equilibrium time at 35 °C and much shorter time of 4 min is achieved at 75 °C. Further, Avrami's fractional-order kinetic model was used and fitted well with the experiment data, which shows good consistency between experimental results and theoretical model. In addition, PMMA-[N1111][Gly] remained excellent durability in the continuous adsorption–desorption cycling test. Therefore, this stable PMMA-[N1111][Gly] sorbent has great potential to be used for fast CO_2 adsorption from flue-gas.

Treatment of tunnel wash waters-experiments with organic sorbent materials.PartⅠ:Removal of polycyclic aromatic hydrocarbons and nonpolar oil

Tunnel wash waters characterize all waters that run off after washing procedures of tunnels are performed.These waters represent a wide spectrum of organic and inorganic pollutants,such as polycyclic aromatic hydrocarbons(PAHs)and toxic metals.Removal of such contaminants from water runoff was investigated using laboratory tests after washing procedure was performed on two road tunnels in eastern Norway(Hanekleiv and Bragernes).Due to diverse character of both,treatment media and treated wash waters, the wh...

A New Solid Sorbent System for Rapid Monitoring of Dehydrogenated Nicotine by Using Furfural-hydrochloric Acid

A new solid sorbent system is developed for the monitoring of dehydrogenated nicotine in the environment. The reagent system for the indicator tube consists of furfural-hydrochloric acid and phosphoric acid impregnated over a cellulose fibre （cotton） and a humectant calcium chloride. The reagent system has also been used for the preparation of reagent paper. After exposing the indicator tubes and test paper to dehydrogenated nicotine, for a constant time, the red-violet colour developed could be compared with those obtained from standards. Alternatively the coloured compound was extracted in water and the absorbance measured at 540 nm. The lower limit of detection is 0.03 μg/m^3 of nicotine for the reagent papers and indicator tubes. The lower limit of determination by spectrophotometric procedure is 0.001μg/m^3 of air. The preparation of indicator tubes, test papers and their applications for the detection and determination of nicotine in environmental tobacco smoke （ETS）, mainstream smoke （MS）, side stream smoke （SS） and biological samples is described in this paper.

Effect of binder on the properties of iron oxide sorbent for hot gas desulfurization

The most difficult problem in hot gas desulfurization in Integrated Coal Gasification Combined Cycle （IGCC） is the pulverization of sulfur removal sorbents.Appropriate binders for hot gas sulfur removal sorbents can solve the pulverization problem.In this paper,six sorbents with binders of different argillaceous minerals were prepared by mechanical mixing method.Desulfurization behavior for hot gas desulfurization sorbents was investigated in a fixed-bed reactor.Result showed that sorbent NTKW2 with binder of clay had a better sulfidation performance.NTKW2 had a more stable performance than other sorbents in the continuous sulfidation-regeneration cycles.Sulfur capacity of sorbent remained the same in each cycle.The desulfurization efficiency and mechanical strength of NTKW2 were the best among the tested sorbents.The behavior of NTKW2 at different temperatures showed different performances,and the best reaction temperature was 550 ℃.Higher heat stability,sulfur capacity and desulfurization efficiency were found on NTKW2 in six continuous sulfidation-regeneration cycles.

Efficient Theoretical Screening of Solid Sorbents for CO₂Capture Applications

By combining thermodynamic database mining with first principles density functional theory and phonon lattice dynamics calculations, a theoretical screening methodology to identify the most promising CO2 sorbent candidates from the vast array of possible solid materials has been proposed and validated. The ab initio thermodynamic technique has the advantage of allowing identification of thermodynamic properties of CO2 capture reactions without any experimental input beyond crystallographic structural information of the solid phases involved. For a given solid, the first step is to attempt to extract thermodynamic properties from thermodynamic databases and the available literatures. If the thermodynamic properties of the compound of interest are unknown, an ab initio thermodynamic approach is used to calculate them. These properties expressed conveniently as chemical potentials and heat of reactions, which obtained either from databases or from calculations, are further used for computing the thermodynamic reaction equilibrium properties of the CO2 absorption/desorption cycles. Only those solid materials for which lower capture energy costs are predicted at the desired process conditions are selected as CO2 sorbent candidates and are further considered for ex- perimental validations. Solid sorbents containing alkali and alkaline earth metals have been reported in several previous studies to be good candidates for CO2 sorbent applications due to their high CO2 absorption capacity at moderate work- ing temperatures. In addition to introducing our computational screening procedure, in this presentation we will sum- marize our results for solid systems composed by alkali and alkaline earth metal oxides, hydroxides, and carbonates/bicarbonates to validate our methodology. Additionally, applications of our computational method to mixed solid systems of Li2O with SiO2/ZrO2 with different mixing ratios, our preliminary results showed that increasing the Li2O/SiO2 ratio in lithium silicates increases their corresponding turnover temperatures for CO2 capture reactions. Overall these theoretical predictions are found to be in good agreement with available experimental findings.