Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electr...Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.展开更多
Improving the galvanizability of high silicon advanced high strength steels （AHSS） is a practical technical challenge. In this study, spot defects on an industrial hot dip galvanized （GI） sheet of an AHSS with 1.5...Improving the galvanizability of high silicon advanced high strength steels （AHSS） is a practical technical challenge. In this study, spot defects on an industrial hot dip galvanized （GI） sheet of an AHSS with 1.5 % Si has been studied in-depth. The surface morphologies of spot defects before and after partial and complete removal of the Zn layer, as well as the interface between the outermost coating layer and the sheet substrate were characterized using optical microscopy （ OM）, scanning electron microscopy （ SEM）, a 3-D optical profiler, energy dispersive spectroscopy（ EDS ） and focused ion beam （FIB） analysis. The most outstanding spot defect on the normally coated area of the steel sheet has a diameter of approximately 500μm, with the following characteristics. In the central region of the spot defect,Zn is barely coated and the sheet substrate is covered by a thin silicon oxide film with dispersed Zn-Fe intermetallics. At the periphery of the spot defect, a burst structure of Zn-Fe intermetallics forms on the sheet substrate. Outside the spot defect where the Zn layer is normally coated, there is a continuous Fe2Al5 inhibition layer between the Zn coating and the sheet substrate. These results indicate that a silicon oxide film forms on the substrate during annealing prior to hot dipping, thus preventing the formation of the Fe2Al5 inhibition layer during hot dipping. This causes spot defects on high Si AHSS sheets.展开更多
The response of three-dimensional sample of Al, containing vacancy complex, under shear loading was simulated. The molecular dynamics method was used and interaction between atoms was described on the base of pseudopo...The response of three-dimensional sample of Al, containing vacancy complex, under shear loading was simulated. The molecular dynamics method was used and interaction between atoms was described on the base of pseudopotential theory Solitary waves were generated in the sample under mechanical loading. Their interaction with the vacancy complexes was shown to be able to initiate hot spot in that local region of the complexes. Some parameters of the hot spot as well as solitary waves were calculated. The initiation of the hot spot is accompanied with sufficient local structural relaxation.展开更多
文摘Many spot defects were found on the surface of a cold-rolled Fe-36%Ni alloy strip produced in a factory,which seriously affected the surface quality of the product.Through metallographic microscopy and scanning electron microscopy analyses,it was found that the spot defects were caused by the residual oxide layer on the surface of the cold-rolled Fe-36%Ni alloy strip after hydrogen annealing.By properly increasing the grinding amount of the blank before cold rolling to remove the oxide layer,the spot defects on the surface of the cold-rolled strip were effectively eliminated,and the surface quality of the product was ensured.
文摘Improving the galvanizability of high silicon advanced high strength steels （AHSS） is a practical technical challenge. In this study, spot defects on an industrial hot dip galvanized （GI） sheet of an AHSS with 1.5 % Si has been studied in-depth. The surface morphologies of spot defects before and after partial and complete removal of the Zn layer, as well as the interface between the outermost coating layer and the sheet substrate were characterized using optical microscopy （ OM）, scanning electron microscopy （ SEM）, a 3-D optical profiler, energy dispersive spectroscopy（ EDS ） and focused ion beam （FIB） analysis. The most outstanding spot defect on the normally coated area of the steel sheet has a diameter of approximately 500μm, with the following characteristics. In the central region of the spot defect,Zn is barely coated and the sheet substrate is covered by a thin silicon oxide film with dispersed Zn-Fe intermetallics. At the periphery of the spot defect, a burst structure of Zn-Fe intermetallics forms on the sheet substrate. Outside the spot defect where the Zn layer is normally coated, there is a continuous Fe2Al5 inhibition layer between the Zn coating and the sheet substrate. These results indicate that a silicon oxide film forms on the substrate during annealing prior to hot dipping, thus preventing the formation of the Fe2Al5 inhibition layer during hot dipping. This causes spot defects on high Si AHSS sheets.
文摘The response of three-dimensional sample of Al, containing vacancy complex, under shear loading was simulated. The molecular dynamics method was used and interaction between atoms was described on the base of pseudopotential theory Solitary waves were generated in the sample under mechanical loading. Their interaction with the vacancy complexes was shown to be able to initiate hot spot in that local region of the complexes. Some parameters of the hot spot as well as solitary waves were calculated. The initiation of the hot spot is accompanied with sufficient local structural relaxation.
