Modeling and Simulation Study on Reverse Swirl of Secondary Air in Large Tangentially Fired Boiler

Based on the porosity method and the improved non uniform QUICK scheme, this paper describes a three dimensional computer simulation to predict the flow characteristics in a tangentially fired boiler. The model is applied to a 600?MW boiler modeling under different operating conditions of reverse swirl of secondary air. The numerical results achieve reasonable agreement with experimental data. The calculated results of flow field, the pressure distribution, the relative diameter of tangential circle, angular momentum flux in furnace and the velocity distribution index in horizontal gas pass are analyzed in detail. And then the effects of the reverse swirl of secondary air on flue gas imbalance are discussed. Finally a reasonable operating condition of the reverse swirl of secondary air is presented.

Sliding Mode Predictive Control of Main Steam Pressure in Coal-fired Power Plant Boiler

Since the combustion system of coal-fired boiler in thermal power plant is characterized as time varying, strongly coupled, and nonlinear, it is hard to achieve a satisfactory performance by the conventional proportional integral derivative (PID) control scheme. For the characteristics of the main steam pressure in coal-fired power plant boiler, the sliding mode control system with Smith predictive structure is proposed to look for performance and robustness improvement. First, internal model control (IMC) and Smith predictor (SP) is used to deal with the time delay, and sliding mode controller (SMCr) is designed to overcome the model mismatch. Simulation results show the effectiveness of the proposed controller compared with conventional ones.

INTRODUCTION TO INCONEL ALLOY 740: AN ALLOY DESIGNED FOR SUPERHEATER TUBING IN COAL-FIRED ULTRA SUPERCRITICAL BOILERS

Chinese utilities as well as those worldwide are facing increased demand for additional electricity, reduced plant emissions and greater efficiency. To meet this challenge will require increasing boiler temperature, pressure and coal ash corrosion resistance of the materials of boiler construction of future coal-fired boilers. A new nickel-based tube alloy, INCONEL^R alloy 740, is described aiming at meeting this challenge. Emphasis will be on describing the alloy＇ s mechanical properties, coal-ash and steam corrosion resistance. Microstructural stability as a function of temperature and time is addressed as well as some of the early methodology em- ployed to arrive at the current chemical composition.

Computational Modeling of Tangentially Fired Boiler(Ⅱ) NO_x Emissions

The paper describes numerical and experimental study on reduction of NOx emissions in a 600 MW tangentially fired boiler furnace under different operating conditions. A simplified NOX formation mechanism model, along with the gas-particle multiphase flow model, is adopted. The prediction yields encouraging results as compared to experimental data.

Feasibility Analysis on the Integrated Application of Solar Energy, Biogas, Coal-fired Boiler and Radiant Floor Heating for Rural Residence

The feasibility of adopting a balanced energy mix mode (domestic solar energy, biogas, coal-fired boiler and radiant floor heating) was proposed. Taking a typical rural residence in Zhengzhou City for example, the study through theoretical analysis and calculation showed that such a balanced energy mix is an economic way and efficient in saving energy and reducing air pollution, and elaborated the theoretical feasibility of popularizing such a heat supply mode in rural areas.

Computational Modeling of Tangentially Fired Boiler (I) Models, Flow Field and Temperature Profiles

In this work, an Eulerian/Lagrangian approach has been employed to investigate numerically the flow characteristics, heat transfer and combustion in a tangentially fired furnace. The RNG (Re-normalization group) k-ε model and a new method for cell face velocity interpolation based on a non-staggered grid system are employed. To avoid pseudo-diffusion that is significant in modeling tangentially fired furnaces, attempts are made at improving the differential volume scheme. Some new developments on turbulent diffusion of particles are also taken into account. Thus, computational accuracy is improved substantially.

Simulation on an optimal combustion control strategy for 3-D temperature distributions in tangentially pc-fired utility boiler furnaces

The control of 3-D temperature distribution in a utility boiler furnace is essential for the safe, economic and clean operation of pc-fired furnace with multi-burner system. The development of the visualization of 3-D temperature distributions in pc-fired furnaces makes it possible for a new combustion control strategy directly with the furnace temperature as its goal to improve the control quality for the combustion processes. Studied in this paper is such a new strategy that the whole furnace is divided into several parts in the vertical direction, and the average temperature and its bias from the center in every cross section can be extracted from the visualization results of the 3-D temperature distributions. In the simulation stage, a computational fluid dynamics(CFD) code served to calculate the 3-D temperature distributions in a furnace, then a linear model was set up to relate the features of the temperature distributions with the input of the combustion processes, such as the flow rates of fuel and air fed into the furnaces through all the burners. The adaptive genetic algorithm was adopted to find the optimal combination of the whole input parameters which ensure to form an optimal 3-D temperature field in the furnace desired for the operation of boiler. Simulation results showed that the strategy could soon find the factors making the temperature distribution apart from the optimal state and give correct adjusting suggestions.

Development of 600 MW Class Coal Fired Boilers in China

This article introduces the present status anddevelopment of 600 MW class boilers in China. The statisticaldata indicate that most 600 MW generating units experiencedrelatively length" growing up" period. In this period, unitscould not operate stably , their unplanned outage times weremany and durations long, and availabilities low. On the basis oftesting and research and the summing-up of practice, it wasindicated slagging in the furnace, deviation of tine gas energy atthe exit of furnace, and overheating bursting of superheater andreheater etc, endangering the safety and economics ofoperation,main problems could be completely alleviated oravoided through design and type selection of boiler furnace andburners, coal characteristics and coal handling management,and optimization management of operation conditions etc.

System Performance and Pollution Emission of Biomass Gas Co-Firing in a Coal-Fired Boiler

To reduce greenhouse gases emission and increase the renewable energy utilization portion in the world, the biomass gasification coupled with a coal-fired boiler power generation system is studied. It is a challenge to achieve optimum performance for the coupled system. The models of biomass gasification coupled with co-firing of coal in a boiler have been established. A comparative study of three kinds of biomass (Food Rubbish, Straw and Wood Pellets) has been done. The syngas produced in a 10 t/h gasifier is fed to a 330 MWe coal-fired boiler for co-combustion, and the co-firing performances have been compared with pure coal combustion case under the conditions of constant boiler load. Results show that co-firing decreases the furnace combustion temperature and raises the flue gas temperature for Food Rubbish and Straw, while, flue gases temperature decrease in case of Wood Pellets. At the same time NOx and SOx emissions have reduced. The system efficiencies at constant load for Food Rubbish, Straw and Wood Pellets are 83.25%, 83.88% and 82.56% when the optimum conditions of gasification and co-firing process are guaranteed.

Corrosion control experience and water chemistry studies on fossil-fired plants

BackgroundThe power industry has long been plagued with complicationsand outages related to corrosion of plant components.Prior to the mid-sixties,corrosion of boiler water-wall tubeswas one of the prominent problems in power plants.Water-walltubes corrosion proceeding under iron oxide deposit caused causticgouging or acidic embrittlement of tube metal.Many boiler tubesfailed by sudden rupture.Field and laboratory studies showed that,carbonate alkalinity and neutral salt in boiler make up water

燃用高碱煤锅炉受热面结焦及其防治研究概述

以准东煤为代表的高碱煤虽储量巨大,但火电机组掺烧高碱煤过程中造成锅炉受热面结焦问题突出,不仅降低锅炉热效率,而且严重威胁机组安全、稳定、经济运行。为解决结焦技术难题,促进高碱煤掺烧利用,对燃用高碱煤锅炉受热面结焦及其防治研究进行了综述。截至目前,国内外围绕燃煤锅炉受热面结焦特征、结焦机理、影响因素、防治措施等已经开展了广泛研究并取得了丰硕的研究成果。在控制燃煤质量、改善锅炉结构、优化锅炉运行等措施基础上,在锅炉受热面制备涂层成为防治结焦的重要技术途径。在未来研究过程中,涂层在具备突出抗结焦性能的同时,须兼具优良的耐高温、抗腐蚀、耐磨损、导热性、热疲劳等综合性能,且具有良好的制备经济性、制备效率,特别是现场适用性。

某660 MW超临界锅炉深度调峰过程中分隔屏超温计算分析及改造方案研究

针对660 MW超临界褐煤锅炉分隔屏实炉数据分析发现,在175 MW负荷下,分隔屏的超温报警主要发生在屏3、屏4靠近炉内的管子。为解决分隔屏超温报警问题,采用流动网络系统法,结合质量、能量和动量守恒方程建立了分隔屏水动力计算数学模型,提出添加节流圈以及升级管子材料两种改造方案。对分隔屏进行回路及管段划分,采用175 MW负荷实炉测量数据反推计算得到炉内实际热偏差,对低、中、高负荷下添加节流圈与升级材料为Super304H的分隔屏出口汽温进行计算。计算结果表明:添加节流圈后分隔屏出口汽温偏差变小,且屏3、屏4出口汽温降低至材料TP347H报警温度以下;升级材料为Super304H后分隔屏出口汽温均小于材料的报警温度,分隔屏可安全运行。对添加节流圈以及将材料升级为Super304H两种方案进行壁温计算及强度校核,结果显示两种改造方案在各个负荷下,壁温以及强度均是安全的。为给锅炉运行留出更大的安全裕度,建议在分隔屏最后一片屏上添加节流圈的同时将材料由TP347H升级为Super304H。

燃煤机组锅炉负荷偏差分析模型与评价系统

“双碳”大背景下我国上网新能源装机发展十分迅速。为了加大电网对新能源发电的消纳,燃煤发电机组频繁参与深度调峰导致了机组实际负荷与自动发电控制(AGC)指令负荷出现较大偏差。针对这一技术难题,以锅炉及其辅助设备为对象,研究构建了锅炉机组本体及其辅助设备的实际出力模型、应有出力模型和最大出力模型,建立了用以分析评价锅炉机组负荷偏差原因及诊断与预警的分析评价系统,并将该系统在电厂中进行了验证。结果表明:该分析评价系统可有效地对锅炉及其辅助设备的出力故障进行早期预警和诊断,可有效提高机组运行的可靠性、安全性与经济性。

宽负荷下切圆燃煤锅炉H_(2)S分布特性的数值模拟

锅炉采用空气分级燃烧降低NO_(x)排放的同时也提高了主燃区H_(2)S体积分数。炉墙壁面过高的H_(2)S体积分数是加剧水冷壁高温腐蚀的重要因素。为保障新能源并网发电,大型燃煤机组灵活调峰的需求增加,不同负荷下的水冷壁近壁面H_(2)S分布特性值得关注。通过正交试验分析了切圆燃煤锅炉运行参数对水冷壁近壁面H_(2)S体积分数分布的影响。选取一台超临界600 MW切圆燃煤锅炉建立数值模型,设计L_(16)(4^(5))正交工况,覆盖100%BMCR、75%THA,50%THA以及35%BMCR四种负荷。建立了自定义SO_(x)生成模型以确定燃料硫的析出和转化路径,模型包含多表面反应子模型以描述焦炭与O_(2)/CO_(2)/H_(2)O等3种气体的异相反应,并确定焦炭气化反应消耗量占总消耗量的比例,进而对炉膛H_(2)S空间分布进行了模拟计算。研究表明,近壁面高体积分数H_(2)S区域主要位于投运燃烧器层中最下层燃烧器以下以及最上层燃烧器以上至SOFA层之间,烟气切圆沿炉膛高度增加逐渐增大是造成后一区域H_(2)S体积分数较高的重要原因。35%BMCR负荷下水冷壁重点区域的H_(2)S平均体积分数为364μL/L,明显低于其他负荷。锅炉运行参数对重点区域H_(2)S体积分数影响程度的排序为:锅炉负荷>一次风率>主燃区空气过量系数>假想切圆直径>燃烧器竖直摆角。

氨煤混燃气相中NO生成的化学反应动力学分析

氨煤混燃涉及复杂的化学反应过程,是否会加剧氮氧化物的生成是倍受关注的问题。通过化学反应动力学计算方法,研究了氨煤混合燃烧的气相反应中NO生成和还原的反应路径,以及不同因素对NO生成的影响。结果表明:温度T=1300℃、过量空气系数α=0.84时,相较于纯煤燃烧,掺氨比例为0.3时能够降低反应器出口NO体积分数96.5%,原因是此工况下氨分解产生大量的NH_(2)和NH等自由基,其还原反应的反应速率更快,从而使含N基元向N_(2)转化;T=1300℃下,掺氨比例为0.3时较为合适,此时反应器出口的NO和NH_(3)体积分数均较低;小比例掺氨燃烧会增大NO的生成速率和NH_(3)的分解速率,导致反应器出口NO体积分数增大,且温度越高,该现象越明显;α<1的还原性气氛和较低的温度(T≤1300℃)能够有效降低NO的排放。

燃煤锅炉温度场与高温腐蚀气氛场同步在线检测装置开发及应用

燃煤锅炉主燃区燃烧场的经济性、安全性和环保性对于智慧电厂建设具有重要意义。其中,水冷壁近壁面高温腐蚀H_(2)S和CO气体浓度的实时在线监测尤为重要。为实现燃煤锅炉主燃区温度场和高温腐蚀气氛场的同步测量,基于红外热成像原理,采用Optris-PI1M小型红外热成像仪,基于LabVIEW温度实时采集应用软件,在炉膛的观察口对主燃区温度场进行连续监测。以低成本1.5μm附近的通信波段激光器作为测量高温腐蚀气体H_(2)S和CO的激光光源,并结合波长调制光谱技术和频分复用技术,以实现H_(2)S和CO气体浓度的同步检测。线性度实验表明,其线性拟合相关系数为0.9995。将研制的同步检测仪器对某300 MW四角切圆燃煤锅炉的主燃区的温度场和气氛场进行了现场应用试验。现场测试结果表明,锅炉主燃区温度主要分布范围在1300~1400℃,最高温度达到了1500℃;同时得到了锅炉主燃区的H_(2)S和CO浓度分布,H_(2)S浓度在12~125 mg/m^(3)的范围内波动,而CO浓度主要分布在10%~20%之间,最高可达22%;炉内H_(2)S和CO的浓度呈正相关,氧气浓度保持在1%以下,由于厌氧燃烧会导致两种气体的含量增加,从而造成对水冷壁近壁面的高温腐蚀。

基于改进Node2vec算法的锅炉温度场分割方法研究

针对温度场特征参数差异引发的锅炉温度场分割准确性的问题,以维持温度场特征为目标,引入图结构表达场数据,通过改进Node2vec算法进行聚类分析,进而实现锅炉温度场的最佳分割。该方法基于多维度的特征信息对锅炉温度场实现分割,能够更准确地保留流场特征。在标准数据集上进行了实验验证,结果表明在具有多维度特征的数据集上,所提方法相比其他对比算法在分割效果方面有提升显著。最后将提出的方法用于分割电站锅炉温度场,结果表明该方法可以很好地捕捉温度场数据中的局部和全局特征,且结果具有较好的精确性。

供热锅炉选型与经济性分析

循环流化床锅炉、煤粉工业锅炉因能效高、环保性能好,是燃煤工业锅炉的重要发展方向,为满足锅炉选型需要,从技术性能、运行维护、经济、环保等方面对两种炉型对比分析,并结合项目案例进行实践比选。项目案例表明:因所在地周边无集中制粉厂家,该案例煤粉工业锅炉需要炉前制粉,煤粉工业锅炉方案建设投资比循环流化床锅炉方案高626万元,蒸汽生产成本比循环流化床锅炉方案低33.6万元/a;由于煤粉工业锅炉附属制粉工艺安全隐患较多,因此,从经济性和安全性考虑,项目案例选用循环流化床锅炉方案。两种炉型没有绝对的优劣,循环流化床锅炉适应煤质范围宽,煤粉工业锅炉更适应周边环境要求高、自动化水平高的区域,要根据具体场景、条件,选择最适宜的炉型。

层燃锅炉横向空气分级脱硝技术的试验研究

与大多数燃煤层燃锅炉炉膛装有纵向空气分级脱硝工艺不同,尝试在炉排上实现横向的空气分级技术,即使用一次风不均匀配置,减少中心火焰段的供风量,减少量补充到炉床后段,在高温火焰段创造深度还原性气氛,再通过侧壁上的烟气循环射流,让热解气与燃料层有更长的接触停留时间,实现燃料型NO_(x)排放的降低。该技术在某46 MW燃煤层燃锅炉上进行尝试,试验结果展示:燃烧室中炉排上火焰被拉长,火焰峰值温度的位置由距前墙2.62 m延后至3.52 m处,火焰中出现高CO浓度的还原区。炉排上NO_(x)的峰值浓度从改造前的535 mg/m^(3)降低至322 mg/m^(3)。尾部烟气中NO_(x)浓度从350 mg/m^(3)左右降低至260~290 mg/m^(3),实现脱硝效率17.1%~25.7%。改造对大渣燃尽率、锅炉功率、炉内烟气温度等没有影响。该技术对于层燃锅炉实现炉内火焰脱硝有一定的工业指导意义。

燃气锅炉振动问题探究

本文对燃气锅炉运行期间存在的振动问题进行了研究。对于对冲燃气燃烧器的典型锅炉,在50%负荷以上,前墙单只燃烧器的燃气开度为后墙燃气开度的一半时,振动明显减弱。