Temperature and stress fields in electron beam welded Ti-15-3 alloy to 304 stainless steel joint with copper interlayer sheet

Electron beam welding of Ti-15-3 alloy to 304 stainless steel （STS） using a copper filler metal was carried out. The temperature fields and stress distributions in the Ti/Fe and Ti/Cu/Fe joint during the welding process were numerically simulated and experimentally measured. The results show that the rotated parabola body heat source is fit for the simulation of the electron beam welding. The temperature distribution is asymmetric along the weld center and the temperature in the titanium alloy plate is higher than that in the 304 STS plate. The thermal stress also appears to be in asymmetric distribution. The residual tensile stress mainly exists in the weld at the 304 STS side. The copper filler metal decreases the peak temperature and temperature grade in the joint as well as the residual stress. The longitudinal and lateral residual tensile strengths reduce by 66 MPa and 31 MPa, respectively. From the temperature and residual stress, it is concluded that copper is a good filler metal candidate for the electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel.

Effect of Aging Temperature on Erosion-Corrosion Behavior of 17-4PH Stainless Steels in Dilute Sulphuric Acid Slurry

The effect of aging temperature on erosion corrosion （E-C） behavior of 17-4PH stainless steels in dilute sulphuric acid slurry containing solid particles was studied by using self-made rotating E-C apparatus. The effect of impact velocity on EC behavior of 17 4PH steels at different aging temperatures was analyzed. Surface micrographs of the specimens after E C test were observed by using scanning electron microscope （SEM）. The results showed that under the condition of the same solution heat treatment, when aging temperature ranged from 400 ℃ to 610℃, the hardness reached the highest value near the temperature 460℃. The characteristics of E-C for 17-4PH stainless steels at different aging temperatures were as follows： pure erosion （wear） was dominant, corrosion was subordinate and at the same time corrosion promoted erosion. The effect of aging temperature on E-C rate of 17-4PH steels was not significant at low impact velocity, but it was found that E-C resistance of 17-4PH steels aged near 460℃ was the most excellent due to the best precipitation strengthening effect of fine and dispersed e-Cu phase. With a prerequisite of appropriate corrosion resistance, the precipitation hardening could significantly improve the E-C resistance of the materials.

Deformation behaviors of 21-6-9 stainless steel tube numerical control bending under different friction conditions

For contact dominated numerical control(NC) bending process of tube, the effect of friction on bending deformation behaviors should be focused on to achieve precision bending forming. A three dimensional(3D) elastic-plastic finite element(FE) model of NC bending process was established under ABAQUS/Explicit platform, and its reliability was validated by the experiment. Then, numerical study on bending deformation behaviors under different frictions between tube and various dies was explored from multiple aspects such as wrinkling, wall thickness change and cross section deformation. The results show that the large friction of wiper die-tube reduces the wrinkling wave ratio η and cross section deformation degree ΔD and increases the wall thinning degree Δt. The large friction of mandrel-tube causes large η, Δt and ΔD, and the onset of wrinkling near clamp die. The large friction of pressure die-tube reduces Δt and ΔD, and the friction on this interface has little effect on η. The large friction of bending die-tube reduces η and ΔD, and the friction on this interface has little effect on Δt. The reasonable friction coefficients on wiper die-tube, mandrel-tube, pressure die-tube and bending die-tube of 21-6-9(0Cr21Ni6Mn9N) stainless steel tube in NC bending are 0.05-0.15, 0.05-0.15, 0.25-0.35 and 0.25-0.35, respectively. The results can provide a guideline for applying the friction conditions to establish the robust bending environment for stable and precise bending deformation of tube bending.

Relationship of microstructure transformation and hardening behavior of type 17-4 PH stainless steel

The relationship between the microstructure transformation of type 17-4 PH stainless steel and the aging hardening behavior was investigated. The results showed that, when 17-4 PH stainless steel aging at 595℃, the bulk hardness of samples attains its peak value （42.5 HRC） for about 20 min, and then decreases at all time. TEM revealed the microstructure corresponding with peak hardness is that the fine spheroid-shape copper with the fcc crystal structure and the fiber-shape secondary carbide M23C6 precipitated from the lath martensite matrix. Both precipitations of copper and M23C6 are the reasons for strengthening of the alloy at this temperature. With the extension of holding time at this temperature, the copper and secondary carbide grow and lose the coherent relationship with the matrix, so the bulk hardness of samples decreases.

Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with copper interlayer sheet

Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy(SEM) and X-ray diffractometry(XRD).In addition,the mechanical properties of the joint were evaluated by tensile test and the microhardness was measured.These two alloys were successfully welded by adding copper transition layer into the weld.Solid solution with a certain thickness was located at the interfaces between weld and base metal in both sides.Regions inside the weld and near the stainless steel were characterized by solid solution of copper with TiFe2 intermetallics dispersedly distributed in it.While weld near titanium alloy contained Ti-Cu and Ti-Fe-Cu intermetallics layer,in which the hardness of weld came to the highest value.Brittle fracture occurred in the intermetallics layer when the joint was stretched.

Microstructure and mechanical properties of similar and dissimilar metal gas tungsten constricted arc welds:Maraging steel to 13-8 Mo stainless steel

Maraging steel (250) and 13-8 Mo stainless steel plates were joined by gas tungsten constricted arc welding(GTCAW) process in similar and dissimilar metal combinations using 13-8 Mo stainless steel filler wire. The similar and dissimilar metal welds made in solutionized condition were subjected to standard post weld hardening treatments direct ageing at 485 ℃, soaking for 31/2 hours followed by air cooling(ageing treatment of maraging steel) and direct ageing at 510 ℃, soaking for 4 h followed by air cooling(ageing treatment of 13-8 Mo stainless steel). The joint characterization studies include microstructure examination, microhardness survey across the weldments and transverse weld tensile test.Similar and dissimilar metal weldments responded to both the post weld ageing treatment. After post weld aging, increase in yield strength, UTS and slight reduction in % elongation of similar and dissimilar metal were observed. The observed tensile properties were correlated with microstructure and hardness distribution across the welds.

EFFECT OF DYNAMIC STRAIN AGING ON LOW CYCLE FATIGUE BEHAVIOUR OF 18-8 AUSTENITIC STAINLESS STEEL

Studies were made of the symmetric tensile-compressive low cycle fatigue behaviour and the influence of dynamic strain aging(DSA)pre-treatment of 18-8 austenitic stainless steel. Within the testing amplitude range of strain.±0.5 % to±1.5 %,the three processes of cyclic hardening,cyclic saturation and cyclic softening were observed.In the same amplitude of strain,the peak stress of the samples pre-treated by DSA is higher than that of solid-solu- tion and cold working pre-treatment,but no remarkable differences of the fatigue lives of them were found.TEM observation shows that the uniform and stable dislocation networks with high density form after DSA pre-treatment,which increases the cyclic peak stress.The cyclic softening results from the low dislocation density and elongated cell structure with low energy.

Corrosive-wear resistance of stainless steels for the impeller of slurry pump used in zinc hydrometallurgy process

This paper presents corrosive-wear (C-W) behaviors of three kinds of steels under the simulating condition oftraditional zinc hydrometallurgy process by using a self-made rotating disk apparatus. Result shows that pure wear lossrate is significantly larger than pure corrosion loss rate. Under this C-W condition, the ranking of C-W resistance is S2 >S3 > S1 (S1: austenite stainless steel; S2: CD-4MCu duplex stainless steel; S3 :17-4PH stainless steel). S2 has excellentC-W resistance due to strong surface deformation strengthening effect of high-density dislocations of the γ phase. S3 alsohas excellent C-W resistance owing to high hardness and strength. However, S1 does not show good C-W resistanceunder strong erosion of liquid-solid slurry because of its single-phase austenitic structure and very low hardness. As aresult, duplex stainless steels as well as 17-4 PH stainless steel can be used as impeller candidate materials in the zinchydrometallurgy process due to their excellent C-W resistance and lower cost.

MIXED MODE SCC OF 18-8 STAINLESS STEEL IN BOILING 42% MgCl_2 SOLUTION

A series of mixed mode tests were carried out on 18-8 stainless steel in boiling 42% MgCl_2 solution.The results show that for any K_Ⅱ/K_Ⅰ ratio,the SCC direction coin- cides well with the crack tip maximum normal stress plane,while the SCC resistance of the material reduces as the ratio of K_Ⅱ/K_Ⅰ increases.The experimental results were discussed in the light of anode dissolving mechanism and the effect of mixed mode loading on crack tip stress and strain.It is concluded that for fracture analysis if mixed mode cracks were simply taken into account as mode Ⅰ cracks,and only mode Ⅰ testing results as mode Ⅰ fracture criter- ion were employed,it may not be safe.

Effect of Heat Treatment on Gradient Microstructure and Tensile Property of Laser Powder Bed Fusion Fabricated 15-5 Precipitation Hardening Stainless Steel

This work investigated the gradient microstructure evolution and tensile property of LPBF fabricated 15-5 precipitation hardening stainless steel in post-process direct ageing(DA)and solution treating&ageing(STA).The varied microstructures for austenite and small-sized oxide inclusions at different sample heights in the as-built(AB)condition was generally preserved after DA treatment.However,austenite was almost disappeared,and oxide particle grew significantly after the STA treatment.As a result,the tensile property differences in sample top and bottom for AB and DA conditions did not occur in the STA samples.For the influence of post-process heat treatment,the STA condition had the highest yield strength due to the highest volume fraction of nano-sized Cu precipitates.However,the DA specimen had the highest ultimate tensile strength and elongation owing to the considerable amount of austenite phase and associated transformation induced plasticity effect.

Analyzing the Interplay of Sintering Conditions on Microstructure and Hardness in Indirect Additive Manufacturing of 17-4PH Stainless Steel

Indirect additive manufacturing(AM)methods have recently attracted attention from researchers thanks to their great potential for cheap,straightforward,and small-scale production of metallic components.Atomic diffusion additive manufacturing(ADAM),a variant of indirect AM methods,is a layer-wise indirect AM process recently developed based on fused deposition modeling and metal injection molding.However,there is still limited knowledge of the process conditions and material properties fabricated through this process,where sintering plays a crucial role in the final consolidation of parts.Therefore,this research,for the first time,systematically investigates the impact of various sintering conditions on the shrinkage,relative density,microstructure,and hardness of the 17-4PH ADAM samples.For this reason,as-washed samples were sintered under different time-temperature combinations.The sample density was evaluated using Archimedes,computed tomography,and image analysis methods.The outcomes revealed that sintering variables significantly impacted the density of brown 17-4PH Stainless Steel samples.The results indicated more than 99% relative densities,higher than the value reported by Markforged Inc.(~96%).Based on parallel porosities observed in the computed tomography results,it can be suggested that by modifying the infill pattern during printing,it would be possible to increase the final relative density.The microhardness of the sintered samples in this study was higher than that of the standard sample provided by Markforged Inc.Sintering at 1330℃ for 4 h increased the density of the printed sample without compromising its mechanical properties.According to X-ray diffraction analysis,the standard sample provided by Markforged Inc.and“1330℃—4 h”one had similar stable phases,although copper-rich intermetallics were more abundant in the microstructure of reference samples.This study is expected to facilitate the adoption of indirect metal AM methods by different sectors,thanks to the high achievable relative densities reported here.

The effects of fabrication atmosphere condition on the microstructural and mechanical properties of laser direct manufactured stainless steel 17-4 PH

The effects of atmosphere conditions on microstructural and mechanical properties of stainless steel 17-4PH components fabricated by laser direct manufacturing (LDM) were investigated through mea-surements on phase constitution, porosity, tensile strength, fracture morphology, hardness and evolution of substrate temperature. Results showed that the samples produced in air atmosphere condition pos-sessed higher tensile strength and hardness for both as-deposited and heat-treated states than that in Ar chamber condition, due to dispersion strengthening effect of amorphous oxide particles and nitrogen solution strengthening as a result of higher content of oxygen and nitrogen. The temperature of substrate heat accumulation was higher in Ar chamber condition, leading to dramatically lower porosity and more reverse austenite, which also contributed to the lower strength and hardness.

Effect of Aging on Hardening Behavior of 15-5 PH Stainless Steel

Microstructure transformation and aging hardening behavior of 15-5 PH stainless steel were studied by optical microscopy （OM）, X-ray diffraction （XRD） and transmission electron microscopy （TEM）. The results showed that the 15-5 PH stainless steel consists of NbC precipitates and lath matensite with a high dislocation density after solution treatment. With increasing aging temperature and aging time, the martensitic laths were resolved gradually. Meanwhile, the nanometric-sized Cu precipitates gradually coarsened and lost their coherency with＇the martensite matrix, which exhibited an elliptical shape finally. Fine Cu precipitates can lead to significant dispersion hardening effect, while the coarsened Cu precipitates have no contribution to strengthening. The reversed austenite was observed in the speci- mens aged at 550 ℃ and above; moreover, the amount of reversed austenite increased as aging temperature in- creased. The precipitation hardening behavior of 15-5 PH stainless steel may depend on the balance between the softening caused by the formation of reversed austenite and the hardening caused by the precipitation of copper.

On the microstructure and texture evolution in 17-4 PH stainless steel during laser powder bed fusion: Towards textural design

Additive Manufacturing (AM) of metals allows the production of parts with complex designs, offeringadvanced properties if the evolution of the texture can be controlled. 17-4 precipitation hardening (PH)stainless steel is a high strength, high corrosion resistance alloy used in a range of industries suitable forAM, such as aerospace and marine. Despite 17-4 PH being one of the most common steels for AM, thereare still gaps in the understanding of its AM processing–structure relationships. These include the natureof the matrix phase, as well as the development of texture through AM builds under different processingconditions. We have investigated how changing the laser power and scanning strategy affects the microstructure of 17-4 PH during laser powder bed fusion. It is revealed that the matrix phase is δ-ferritewith a limited austenite presence, mainly in regions of the microstructure immediately below melt pools.Austenite fraction is independent of the printing pattern and laser power. However, reducing the timebetween adjacent laser passes during printing results in an increase in the austenite volume fraction.Another effect of the higher laser power, as well as additional remelting within the printing strategy, isan increase in the average grain size by epitaxial ferrite grain growth across multiple build layers andthe development of a mosaic type microstructure. Changes to the scanning strategy have significant impacts on the textures observed along the build direction, while (100) texture along the scanning directionis observed consistently. Mechanisms for texture formation and the mosaic structure are proposed thatpresents a pathway to the design of texture via AM process control.

Stress corrosion cracking behavior of PH13-8Mo stainless steel in Cl^- solutions

The stress corrosion cracking（ SCC） behavior of PH13-8Mo precipitation hardening stainless steel（ PHSS） in neutral NaCl solutions was investigated through slow-strain-rate tensile（ SSRT） test at various applied potentials. Fracture morphology,elongation ratio,and percentage reduction of area were measured to evaluate the SCC susceptibility. A critical concentration of 1. 0 mol / L neutral NaCl existed for SCC of PH13-8Mo steel. Significant SCC emerged when the applied potential was more negative than -0. 15 VSCE,and the SCC behavior was controlled by an anodic dissolution（ AD） process.When the applied potential was lower than -0. 55 VSCE,an obvious hydrogen-fracture morphology was observed,which indicated that the SCC behavior was controlled by hydrogen-induced cracking（ HIC）.Between -0. 15 and -0. 35 VSCE,the applied potential exceeded the equilibrium hydrogen evolution potential in neutral NaCl solutions and the crack tips were of electrochemical origin in the anodic region; thus,the SCC process was dominated by the AD mechanism.

Microstructure characteristics of segregation zone in 17-4PH stainless steel piston rod

The segregation of Cu and Ni in a 17-4PH stainless steel piston rod has been confirmed to be responsible for the cracking after heat treatment.Further investigation showed that the segregation zone was composed of three layers,namely the fine grain martensitic layer,the coarse grain martensitic layer and the coarse grain austenitic layer from the matrix to the crack surface.Three button ingots with the same chemical compositions as those three layers have been prepared to evaluate the grain size distribution,microstructure and mechanical properties.The effects of Cu and Ni segregation on the microstructures of those three layers have been explored by thermodynamic calculation.Based on the microstructure and mechanical properties results,an intensive understanding of the cracking in the segregation zone was therefore reached.

Effect of Aging Temperature on Stress Corrosion Cracking of 17-4 PH Stainless Steel in Wet H_2S Environment

The effect of aging temperature on stress corrosion crocking of 17-4 precipitation-hardened(PH)stainless steel in simulated stimulant oil well environment was studied by the method B-NACE standard bent-beam test.It is found that when aging temperature ranges from 480 to 610℃,the sensitivity of hydrogen embrittlement decreases significantly.

Homogenization on solution treatment and its effects on the precipitation-hardening of selective laser melted 17-4PH stainless steel

17-4 precipitation-hardened(PH)stainless steel(SS)exhibits high strength and good corrosion resistance via Cu-precipitation hardening.Unlike conventional wrought 17-4PH SS,Cu segregation andε-Cu pre-cipitates are observed in additively manufactured(AM)17-4PH SS owing to the repeated rapid cooling after heating,which characterizes the AM process.In this study,solution treatment was conducted under various temperatures(1,000,1,050,1,100,and 1,200℃)and durations(1,2,4,and 8 h)to minimize the negative effects of Cu segregation andε-Cu precipitates on precipitation hardening.The mechanical prop-erties and microstructures of each condition for the Cu precipitation behavior were examined.Although theε-Cu precipitates did not disappear after solution treatment,the average diameter of theε-Cu precipi-tates tended to decrease with increasing solution treatment temperature and duration.Therefore,solution treatment at a temperature of 1,200℃ for 8 h was the best,resulting in improved strength compared to the conventional solution treatment at 1,050℃.Solution treatment on at least 1,100℃ is effective in AM.

不锈钢厂除尘灰的回收利用

介绍了回收利用不锈钢厂烟道灰和氧化铁皮中铬的前期试验研究。在烟道灰和氧化铁皮中配入水和焦粉等物质,在不同的配比下,对样品压块并测定和分析了其抗压强度。找出了样品块强度能够满足冶炼要求的合适工艺参数。根据所用的烟道灰、氧化铁皮和焦粉条件,为达到较高的抗压强度,烟道灰单独压块的原料合适含水量为12%;氧化铁皮与烟道灰的合适配比为1∶4;烟道灰与焦粉配合时,合适的焦粉含量为12%,相应的合适含水量为14%。