Research on Operation Optimization of Heating System Based on Electric Storage Coupled Solar Energy and Air Source Heat Pump

For heating systems based on electricity storage coupled with solar energy and an air source heat pump(ECSA),choosing the appropriate combination of heat sources according to local conditions is the key to improving economic efficiency.In this paper,four cities in three climatic regions in China were selected,namely Nanjing in the hot summer and cold winter region,Tianjin in the cold region,Shenyang and Harbin in the severe cold winter region.The levelized cost of heat(LCOH)was used as the economic evaluation index,and the energy consumption and emissions of different pollutants were analyzed.TRNSYS software was used to simulate and analyze the system performance.The Hooke-Jeeves optimization algorithm and GenOpt software were used to optimize the system parameters.The results showed that ECSA systemhad an excellent operation effect in cold region and hot summer and cold winter region.Compared with ECS system,the systemenergy consumption,and the emission of different pollutants of ECSA system can be reduced by a maximum of 1.37 times.In cold region,the initial investment in an air source heat pump is higher due to the lower ambient temperature,resulting in an increase in the LOCH value of ECSA system.After the LOCH value of ECSA system in each region was optimized,the heating cost of the system was reduced,but also resulted in an increase in energy consumption and the emission of different pollutant gases.

Enhancing Renewable Energy Integration:A Gaussian-Bare-Bones Levy Cheetah Optimization Approach to Optimal Power Flow in Electrical Networks

In the contemporary era,the global expansion of electrical grids is propelled by various renewable energy sources(RESs).Efficient integration of stochastic RESs and optimal power flow(OPF)management are critical for network optimization.This study introduces an innovative solution,the Gaussian Bare-Bones Levy Cheetah Optimizer(GBBLCO),addressing OPF challenges in power generation systems with stochastic RESs.The primary objective is to minimize the total operating costs of RESs,considering four functions:overall operating costs,voltage deviation management,emissions reduction,voltage stability index(VSI)and power loss mitigation.Additionally,a carbon tax is included in the objective function to reduce carbon emissions.Thorough scrutiny,using modified IEEE 30-bus and IEEE 118-bus systems,validates GBBLCO’s superior performance in achieving optimal solutions.Simulation results demonstrate GBBLCO’s efficacy in six optimization scenarios:total cost with valve point effects,total cost with emission and carbon tax,total cost with prohibited operating zones,active power loss optimization,voltage deviation optimization and enhancing voltage stability index(VSI).GBBLCO outperforms conventional techniques in each scenario,showcasing rapid convergence and superior solution quality.Notably,GBBLCO navigates complexities introduced by valve point effects,adapts to environmental constraints,optimizes costs while considering prohibited operating zones,minimizes active power losses,and optimizes voltage deviation by enhancing the voltage stability index(VSI)effectively.This research significantly contributes to advancing OPF,emphasizing GBBLCO’s improved global search capabilities and ability to address challenges related to local minima.GBBLCO emerges as a versatile and robust optimization tool for diverse challenges in power systems,offering a promising solution for the evolving needs of renewable energy-integrated power grids.

Electrically driven single-photon sources

Single-photon sources are building blocks for photonic quantum information processes. Of the many single-photon generation schemes, electrically driven single-photon sources have the advantages of realizing monolithic integration of quantum light sources and detectors without optical filtering, thus greatly simplify the integrated quantum photonic circuits. Here, we review recent advances on electrically driven single-photon sources based on solid-state quantum emitters, such as semiconductor epitaxial quantum dots, colloidal quantum dots, carbon nanotubes, molecules, and defect states in diamond, SiC and layered semiconductors. In particular, the merits and drawbacks of each system are discussed. Finally, the article is concluded by discussing the challenges that remain for electrically driven single-photon sources.

Three-dimensional forward modeling and inversion of borehole-to-surface electrical imaging with different power sources

Borehole-to-surface electrical imaging （BSEI） uses a line source and a point source to generate a stable electric field in the ground. In order to study the surface potential of anomalies, three-dimensional forward modeling of point and line sources was conducted by using the finite-difference method and the incomplete Cholesky conjugate gradient （ICCG） method. Then, the damping least square method was used in the 3D inversion of the formation resistivity data. Several geological models were considered in the forward modeling and inversion. The forward modeling results suggest that the potentials generated by the two sources have different surface signatures. The inversion data suggest that the low- resistivity anomaly is outlined better than the high-resistivity anomaly. Moreover, when the point source is under the anomaly, the resistivity anomaly boundaries are better outlined than when using a line source.

Recent Developments of Modulation and Control for High-Power Current-Source-Converters Fed Electric Machine Systems

The pulse-width-modulated(PWM)current-source converters(CSCs)fed electric machine systems can be considered as a type of high reliability energy conversion systems,since they work with the long-life DC-link inductor and offer high fault-tolerant capability for short-circuit faults.Besides,they provide motor friendly waveforms and four-quadrant operation ability.Therefore,they are suitable for high-power applications of fans,pumps,compressors and wind power generation.The purpose of this paper is to comprehensively review recent developments of key technologies on modulation and control of high-power(HP)PWM-CSC fed electric machines systems,including reduction of low-order current harmonics,suppression of inductor–capacitor(LC)resonance,mitigation of common-mode voltage(CMV)and control of modular PWM-CSC fed systems.In particular,recent work on the overlapping effects during commutation,LC resonance suppression under fault-tolerant operation and collaboration of modular PMW-CSCs are described.Both theoretical analysis and some results in simulations and experiments are presented.Finally,a brief discussion regarding the future trend of the HP CSC fed electric machines systems is presented.

Equivalent circuit model including magnetic and thermo sources for the thermo–magneto–electric coupling effect in magnetoelectric laminates

The nonlinear thermo–magneto–mechanical magnetostrictive constitutive and the linear thermo–mechanical-electric piezoelectric constitutive are adopted in this paper. The bias magnetic field and ambient temperature are equivalent to a magnetic source and a thermo source, respectively. An equivalent circuit, which contains a magnetic source and a thermo source at the input, for the thermo–magneto–electric coupling effect in magnetoelectric（ME） laminates, is established. The theoretical models of the output voltage and static ME coefficient for ME laminates can be derived from this equivalent circuit model. The predicted static ME coefficient versus temperature curves are in excellent agreement with the experimental data available both qualitatively and quantitatively. It confirms the validity of the proposed model. Then the models are adopted to predict variations in the output voltages and ME coefficients in the laminates under different ambient temperatures, bias magnetic fields, and the volume ratios of magnetostrictive phases. This shows that the output voltage increases with both increasing temperature and increasing volume ratio of magnetostrictive phases; the ME coefficient decreases with increasing temperature; the ME coefficient shows an initial sharp increase and then decreases slowly with the increase in the bias magnetic field, and there is an optimum volume ratio of magnetostrictive phases that maximize the ME coefficient.This paper can not only provide a new idea for the study of the thermo–magneto–electric coupling characteristics of ME laminates, but also provide a theoretical basis for the design and application of ME laminates, operating under different sensors.

Designing the cooling system of a hybrid electric vehicle with multi-heat source

In order to reduce the power consumption and meet the cooling demand of every heat source component, three kinds of multi-heat source cooling system schemes were designed base on the characteristic of power split hybrid electric vehicle （HEV）. Using the numerical simulation meth- od, the power system heat transfer model was built. By comparing the performance of three differ- ent schemes through the Simulink simulation, the best cooling system scheme was found. Base on characteristics of these cooling system structures, the reasonableness of the simulation results were analyzed and verified. The results showed that the cooling system designation based on the numerical simulation could describe the cooling system performance accurately. This method could simplify the design process, improve design efficiency and provide a new way for designing a multi-heat source vehicle cooling system.

Electric Potential in Surface Produced Negative Ion Source with Magnetic Field Increasing Toward a Wall

Electric potential near a wall for plasma with the surface produced negative ions with magnetic field increasing toward a wall is investigated analytically. The potential profile is derived analytically by using a plasma-sheath equation, where negative ions produced on the plasma grid （PG） surface are considered in addition to positive ions and electrons. The potential profile depends on the amount and the temperature of the surface produced negative ions and the profile of the magnetic field. The negative potential peak is formed in the sheath region near the PG surface for the case of strong surface production of negative ions or low temperature negative ions. As the increase rate of the magnetic field near the wall becomes large, the negative potential peak becomes small.

Optimal Operation of Electric Vehicles and Distributed Generation Resources in Smart Grid Considering Load Management

Technology advancement and the global tendency to use renewable energy in distributed generation units in the distribution network have been proposed as sources of energy supply.Despite the complexity of their protection,as well as the operation of distributed generation resources in the distribution network,factors such as improving reliability,increasing production capacity of the distribution network,stabilizing the voltage of the distribution network,reducing peak clipping losses,as well as economic and environmental considerations,have expanded the influence of distributed generation(DG)resources in the distribution network.The location of DG sources and their capacity are the key factors in the effectiveness of distributed generation in the voltage stability of distribution systems.Nowadays,along with the scattered production sources of electric vehicles with the ability to connect to the network,due to having an energy storage system,they are known as valuable resources that can provide various services to the power system.These vehicles can empower the grid or be used as a storage supply source when parked and connected to the grid.This paper introduces and studies a two-stage planning framework for the concurrent management of many electric vehicles and distributed generation resources with private ownership.In the first stage,the aim is to increase the profit of electric vehicles and distributed generation sources;finally,the purpose is to reduce operating costs.The proposed scheduling framework is tested on a distribution network connected to bus 5 of the RBTS sample network.Besides distributed generation sources and electric vehicles,we integrate time-consistent load management into the system.Due to distributed generation sources such as photovoltaic systems and wind turbines and the studied design in the modeling,we use the Taguchi TOAT algorithm to generate and reduce the scenario to ensure the uncertainty in renewable energy.MATLAB software is used to solve the problem and select the optimal answer.

Forward simulation of coal fire model by transient electromagnetic method with electrical source

Uncontrolled coal fires are natural disasters that may cause mineral loss and environmental damage.The traditional loop source transient electromagnetic method can effectively detect the low-resistivity region of coal fires,but its detection efficiency is not so good for high-resistivity regions.In view of this limitation,a technique based on electrical source transient electromagnetics is proposed in this paper to detect high-resistivity regions in the spontaneous combustion process of coal.Considering the complex geometry of the coal fire area,an unstructured tetrahedral grid is used in this study to realize the spatial discretization of the model,and solve the electromagnetic field based on a vector finite element algorithm.Numerical analysis is used to investigate methods for detecting coal fires and the characteristics of effective anomalies are further examined to provide guidance for practical detection.

Research Reports on the 12^(th) Five-Year Plan for Electric Power Industry Power Sources

China Electricity Council organized competent authorities across the industry of electric power to work out the ＂Research Reports on the 12th Five-Year Plan for Electric Power Industry＂ in nearly one year,which provides a reference for governmental departments to formulate the 12th Five-Year Plan on energy and electric power industry.The magazine will publish the serial reports including power sources,power grids,equipment manufacture,energy and environment,and power economics.This paper presents the part of ＂power sources,＂ in which the strategies of developing various kinds of power sources are put forward.

Control Power Source of PV-10 Piezoelectric Crystal Valve

Parameters of the power source used to control PV-10 piezoelectric crystal valve are following DC output voltage： 0 - 120 V, continuously controllable, linear enlargement factor of input direct current voltage： approximate 25 times, the accuracy of DC output voltage： ±5%, manual control and automatic control.

Optimization of the Placement and Size of Photovoltaic Source

This paper presents a new optimization study of the placement and size of a photovoltaic source(PVS)in a distribution grid,based on annual records of meteorological parameters(irradiance,temperature).Based on the recorded data,the production output as well as the daily average power(24-h vector)of the PVS is extracted over the year.When a power vector is available,it can be used as an input when searching for the optimal size of the PVS.This allows to take into account the constraint of the variation of the power generated by this source considering the variation of the power consumed by the electrical loads during the whole day.A multi-objective fitness function has been considered.The latter minimizes the active losses and maximizes the voltage stability index during the day,while considering the constraints of the system,that is,the security,technical,geographical,and meteorological constraints.This problem was solved using the Non-dominated Sorting Genetic Algorithm NSGA-II optimization technique under MATLAB 2021.It was applied to the distribution network of Ghardaïa of 59 nodes.

Negative Corona Discharge Ion Source Under Ambient Conditions with Mini Line-cylinder Electrodes

A novel ambient negative corona discharge ion source with mini line-cylinder electrodes is designed. The diameters of inner and outer electrode are 0.16 and 4 mm respectively. With a special assembly method, a perfect coaxiality of the two electrodes is obtained. An injection system utilizing a temperature control technique, achieves a constant and stable concentration of the sample, which is critical to the experiment. The formulas of the corona onset voltage of line-cylinder electrodes are also introduced. The experiment results show that negative substances such as formic acid and acetic acid can be ionized under ambient conditions. When combined with micro electrical mechanical system fabricationprocess, the volume of the ion source can be reduced dramatically, but there is an undesirable surface discharge. To solve the surface discharge problem, an improved structure was designed and tested. The simplicity of the interface of the ion source makes it suitable for mass spectrometer, micro mass spectrometer, ion mobility spectrometer, and high-field asymmetric waveform ion mobility spectrometer applications.

Analysis, Sources and Study of the Biological Consequences of Electromagnetic Pollution

The actions and health effects of electromagnetic fields in the radio frequency (RF) domains, referred to as radio frequencies and HV transmission networks have been studied for several decades. Following the appearance of questions and debates within the population, the actions and potential effects of radiofrequency and HV transport networks on health, in connection with the development of new wireless technologies, are generating a certain revival of interest. Thus, the increasing exposure to electromagnetic fields and the concerns of the public have led health organizations to undertake large-scale research programs to respond to the concerns expressed. These research programs have contributed to significantly increasing the number of studies on the actions and effects of electromagnetic pollution as well as their consequences on living beings. The objective of our research is focused on the analysis, sources, and study of the biological consequences of electromagnetic pollution. To do this, we have used physical laws and theorems, in particular Maxwell-Ampère, Maxwell-Gauss, Maxwell-Faraday, and Ohm’s law, to model the interactions between electromagnetic fields and living matter. In this article we have chosen the approach based on the electrical model of human biological tissue, taking into account on the one hand the physical phenomena of the propagation of an electromagnetic microwave plane wave in the range from 0 to 300GHz and on the other hand, the experimental values to simulate the relaxations α, β and γ and the impedance of the biological tissue faced with the variation of the frequency of propagation of the electromagnetic waves to identify the biological consequences relating thereto. The results obtained in the literature show the linear dependence of bio-impedance on frequency, these observations suggest that the tissue can be physiologically stressed at high frequencies. This can cause biological consequences for humans. The 2D simulation based on the proposed model has been developed as well as the verification of the consistency of the different mathematical models, by comparing the fractal dimensions of the results of the program with those of the figures obtained experimentally.

Experimental Study of a Minitype Atmospheric Non-equilibrium Plasma Source

A mini-type of plasma source was studied experimentally. The results showed that the plasma density, which was generated by an atmospheric non-equilibrium plasma source, rises with the increase in driving electric-field and the momentum of gas particles. For a driving electricfield of 56 kV/cm and a gas particles＇ momentum of 10^9 × 10^-22 g·m/s, the ion density can exceed 10^10/cm^3 while the effective volume of the plasma source is only 2.5 cm^2. This study may help develop a method to generate a minitype plasma source with low energy consumption but high ion concentration. This source can be used in chemical industry, environmental engineering and military applications.

The Background Variation of Natural Source ELF and Its EM Abnormal Phenomena in Yunnan Earthquakes

In order to add earthquake monitoring methods and develop new method research,the ELF Network for Earthquake Monitoring selected 30 stations in the Capital Circle and the Sichuan-Yunnan region. Finding electromagnetic field background variation is the basis of distinguishing the seismic electromagnetic anomalies. This paper introduces the data acquisition and selection of the Shexian,Anqiu,Lijiang and Dali stations which have recorded for longer time with better data and are located on the similar latitude. Then we use the natural source electromagnetic field's auto-power spectrum to express the intensity of the electromagnetic field. By using power spectral data of many frequencies in the observation frequency band,after the data pre-processing and sliding average noising,the background variation of extremely low frequency stations and the range ability were acquired.Taking the Baoshan M5. 1 earthquake on October 30,2015 and Dali M5. 0 earthquake on May 18,2016 as examples,the authors analyzed the earthquake electromagnetic anomaly characteristic of ELF stations around the earthquakes.

Influence of heat loss through probe electrical leads on thermal conductivity measurement with TPS method

The transient plane source(TPS)method is developed recently to measure the thermal conductivity of materials.In the measurement,the heating power is influenced by the heat which is transferred via the probe electrical leads.This fact further influences the measurement accuracy of thermal conductivity.To solve this problem,the influence of heat loss through the electrical leads on the heating power is studied theoretically.The mathematical formula of heat loss is deduced,and the corresponding correction model is presented.A series of measurement experiments on different materials have been conducted by using the hot disk thermal constant analyzer.The results show that the influence of the heat loss on the measurement is sensitive to different test materials and probes with different sizes.When the thermal conductivity of the material is greater than 0.2 W/(m·K),the influence of the heat loss is less than 0.16%,which can be ignored.As to the lower thermal conductivity materials,it is necessary to compensate the heat loss through the electrical leads,and the accuracy of thermal conductivity measurement can be effectively improved.

High Accurate Howland Current Source: Output Constraints Analysis

Howland circuits have been widely used as powerful source for exciting tissue over a wide frequency range. When a Howland source is designed, the components are chosen so that the designed source has the desired characteristics. However, the operational amplifier limitations and resistor tolerances cause undesired behaviors. This work proposes to take into account the influence of the random distribution of the resistors in the modified Howland circuit over the frequency range of 10 Hz to 10 MHz. Both output current and impedance of the circuit are deduced either considering or the operational amplifiers parameters. The probability density function due to small changes in the resistors of the circuit was calculated by using the analytical modeling. Results showed that both output current and impedance are very sensitive to the resistors variations. In order to get higher output impedances, high operational amplifier gains are required. The operational amplifier open-loop gain increases as increasing the sensitivity of the output impedance. The analysis done in this work can be used as a powerful co-adjuvant tool when projecting this type of circuit in Spice simulators. This might improve the implementations of practical current sources used in electrical bioimpedance.

Study on Ultracapacitors Parameter Design and Control Strategy of Electric Bus

Based on the analysis of ultracapacitors efficiency and vehicle driving character, three conditions restricting the ultracapacitors charge/discharge time are derived. The study focuses on ultracapacitors specific design rules decided by charge/discharge time and how to integrate with battery packs and converter through ultracapacitors＇voltage and current double regulators. Through BFC6100-EV electric bus test, it is shown that the proposed method and control strategy are feasible and the system can effectively improve the bus dynamic performance and ability to receive braking energy effectively.