Numerical Simulation of a Two-Phase Flow with Low Permeability anda Start-Up Pressure Gradient

A new numerical model for low-permeability reservoirs is developed.The model incorporates the nonlinear characteristics of oil-water two-phase flows while taking into account the initiation pressure gradient.Related numerical solutions are obtained using a finite difference method.The correctness of the method is demonstrated using a two-dimensional inhomogeneous low permeability example.Then,the differences in the cumulative oil and water production are investigated for different starting water saturations.It is shown that when the initial water saturation grows,the water content of the block continues to rise and the cumulative oil production gradually decreases.

Rules Governing Pressure Distribution for a Traveling Charge Under the Condition of Lagrange Hypothesis

Aim To study the rules governing pressure distribution of traveling charge under the condition of Lagrange hypothesis. Methods\ The study is based on the laws of conservation of momentum and energy. Results\ The gas flow velocity distribution formula at the back of a projectile and the momentum equation of a traveling charge are deduced, and rules governing their pressure distribution under the Lagrange hypothesis conditions are established. The pressure distribution of a traveling charge is compared with that of a conventional charge. Conclusion\ The pressure distribution in the bore of a traveling charge can be accurately predicted. A parabolic pressure distribution type is revealed.

Effects of Hydrogen Charging Time and Pressure on the Hydrogen Embrittlement Susceptibility of X52 Pipeline Steel Material

The effects of hydrogen charging time and pressure on the hydrogen embrittlement(HE)susceptibility of X52 pipeline steel material are studied by slow strain rate tensile tests.The fracture morphologies of the specimens are observed by scanning electron microscopy.The HE susceptibility of the X52 pipeline steel material increases with an increase in both hydrogen charging time and hydrogen pressure.At a charging time of 96 h,the HE susceptibility index reaches 45.86%,approximately 3.6 times that at a charging time of 0 h.Similarly,a charging pressure of 4 MPa results in a HE susceptibility index of 31.61%,approximately 2.5 times higher than that at a charging pressure of 0.3 MPa.

Experimental research on characteristic of start-up pressure wave propagation in gelled crude oil by large-scale flow loop

In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-up pressure wave speeds under various operation conditions were measured,and effects of correlative factors on pressure wave were analyzed.The experimental and theoretical analysis shows that thermal shrinkage and structural properties of gelled crude oils are key factors influencing on start-up pressure wave propagation.The quantitative analysis for these effects can be done by using volume expansion coefficient and structural property parameter of gelled crude oil.A new calculation model of pressure wave speed was developed on the basis of Large-scale flow loop experiment and theoretical analysis.

Effect of Barrier Materials on Discharge Properties in Air at Low Pressure

Dielectric barrier discharge(DBD) is widely investigated in order to obtain uniform low-temperature plasma.Many studies have proved that some barrier materials,especially electrets,can improve the uniformity of discharge.It is regarded as an available way to get atmospheric pressure glow discharge(APGD).In this paper,discharge forms with 4 different barrier materials(alumina,quartz,PTFE and PET) are investigated,and the transition of discharge form depending on the air pressure are recorded to estimate the influence of barrier materials on discharge.By using electrets as barrier materials,homogeneous discharges can be obtained in a more wide pressure range.Under the same experimental conditions,discharges with electrets are more uniform or have larger uniform areas due to the storage and desorption of charges on the surface of electrets.The electrons deposited in the surface layer can be released on next half cycle when the polarity of the applied voltage changes,and provide a number of seed electrons,which makes the discharge more homogeneous.The capacitance and the permittivity of barrier materials have no effect on the discharge form directly.

HYDROGEN DISTRIBUTION AND DIFFUSION BEHAVIOUR IN HIGH PRESSURE HYDROGEN CHARGED AUSTENITIC STEEL BY IMMA

The hydrogen distribution curve along cross-section of high pressure hydrogen charged spec- imens of 21Cr-7Ni-9Mn-N austenitic steel was obtained quantitatively by IMMA(Ion Microprobe Mass Analyzer).Thus the hydrogen solubility and diffusivity may be measured, and the hydrogen permeability and other parameters may be calculated indirectly.The hydrogen distribution in specimens either long-term aged in air or in electron beam weld seam after high pressure hydrogen charging was also examined.

Structural and electrical transport properties of charge density wave material LaAgSb_(2)under high pressure

Layered lanthanum silver antimonide LaAgSb_(2)exhibits both charge density wave(CDW)order and Dirac-cone-like band structure at ambient pressure.Here,we systematically investigate the pressure evolution of structural and electronic properties of LaAgSb_(2)single crystal.We show that the CDW order is destabilized under compression,as evidenced by the gradual suppression of magnetoresistance.At P_(C)~22 GPa,synchrotron x-ray diffraction and Raman scattering measurements reveal a structural modification at room-temperature.Meanwhile,the sign change of the Hall coefficient is observed at 5 K.Our results demonstrate the tunability of CDW order in the pressurized LaAgSb_(2)single crystal,which can be helpful for its potential applications in the next-generation devices.

Spectroscopic Study of a Radio-Frequency Atmospheric Pressure Dielectric Barrier Discharge with Anodic Alumina as the Dielectric

This paper presents the fabrication and a spectroscopic study of a stable radio- frequency dielectric barrier discharge （RF DBD） in Ar with a novel dielectric, anodic alumina, at atmospheric pressure. Dielectric electrodes are fabricated from commercially available low cost impure aluminum strips by a two-step anodization process in 0.3 M solution of oxalic acid. The discharge is found to be stable with excellent spatial uniformity for the RF input power range of 30～80 W. Excitation and rotational temperatures measured in the experiment range of 1472～3255 K and 434～484 K, respectively, as the input power changes from 30 W to 80 W. These temperature ranges are suitable for surface modification applications.

Pressure Effects on the Charge Carrier Transportation of BaF_2 Nanocrystals

The charge transport behavior of barium fluoride nanocrystals is investigated by in situ impedance measurement up to 35 GPa. It is found that the parameters change discontinuously at about 6.9 GPa, corresponding to the phase transition of BaF2 nanocrystals under high pressure. The charge carriers in BaF2 nanocrystals include both Fions and electrons. Pressure makes the electronic transport more difficult. The defects at grains dominate the electronic transport process. Pressure could make the charge-discharge processes in the Fm3m phase more difficult.

Flow-rate Characteristics Measurement of Regulators Based on the Pressure Response in an Isothermal Tank

Regulators are important components in pneumatic system, and their flow-rate characteristics are the key parameters for designers. According to the correlatively international standard and national standard of China, which describe the flow-rate characteristics measurement method of pneumatic regulators, the pressure and the flow are measured point by point, and then the flow-rate characteristics curve is plotted point to point. This method has some disadvantages, such as equipment complexity, much air consumption, and low efficiency. To settle the problems presented above, this paper puts forward a new high efficient and energy saving flow-rate characteristics measurement method of regulators, which is based on the pressure response when charging and discharging to an isothermal tank without any flow meters. The measurement principle, the system and the steps are introduced. And the tracking differentiator is used for the data processing of the pressure difference. Two typical kinds of regulators were experimentally investigated, and their flow-rate characteristics curves were obtained with the new and the conventional method, respectively. Comparatively, it＇s proved that this new method is feasible because it is not only able to meet the demand of the measurement precision, but also to save energy and improve efficiency. Compared to the conventional method, the new method takes only about 1/10 amount of time and consumes about only 1/30 amount of air. Hopefully it will be able to serve as an international standard of flow-rate characteristics measurement method of regulators.

A Flexible Pressure Sensor Based on Poly(dimethylsiloxane) Nanostructures Film

This paper proposed a flexible pressure sensor based on poly(dimethylsiloxane) nanostructures film and report an efficient,simple,and low-cost fabrication strategy via soft nanoimprint lithography.The pressure sensor can convert external pressure or mechanical deformation into electrical signal to detect pressure and strain changes based on the coupling of triboelectrification and electrostatic induction.To enhance the performance of the pressure sensor,it consists of sub-500 nm resolution on the surface of elastic poly(dimethylsiloxane) sensitive layer and an indium tin oxide electrode thin film.When the pressure applied on the nanostructures layer,triboelectrostatic charges are induced.In the experiment,it measures up to sensitivity of 0.8 V/kPa at frequency of 5 Hz.This study results in potential applications such as wearable smart devices and skin-attachable diagnostics sensing systems.

径向不耦合装药孔壁冲击压力特性

径向不耦合装药结构广泛应用于实际爆破工程中,为探究径向不耦合装药孔壁冲击压力的变化规律,基于冲击波理论,利用激波管模型对径向不耦合装药条件下孔内波系作用过程进行简化分析。研究了孔内爆炸冲击波在各介质面的冲击压力,获得了径向不耦合装药条件下孔壁初始冲击压力的计算表达式,模拟了径向不耦合装药时冲击波的作用过程。研究结果表明:径向空气层的存在极大削减了爆炸冲击波压力,孔壁峰值压力在不耦合系数1~2时发生指数型衰减,在不耦合系数大于2时,其衰减速度较缓慢。冲击波作用在孔壁处时存在多个波峰,且初始峰值压力最大,后续峰值压力随时间的延长逐渐减小;随着不耦合系数的增大,初始峰值压力逐渐减小且到达峰值压力的出现时间也逐渐延后;不耦合系数越大,多波峰特性越明显,不耦合系数较小时峰值压力较大,会对围岩产生较大的破坏。为减小对围岩的破坏且满足相应的爆破要求,应充分利用不耦合系数较大时的多波峰特性,根据岩石性质选择合理的径向装药系数。

3种现场混装炸药耦合装药炮孔壁峰值压力计算

炮孔壁峰值压力是产生炮孔周围应力场的源头,是造成孔壁附近岩石破坏的强动载荷。对于耦合装药,炮孔壁峰值压力是由爆轰波碰撞孔壁而生产的,通常这种碰撞是斜碰撞,并不是正碰撞。基于这样的物理事实,通过对现有耦合装药孔壁压力计算方法行了评述,并提出斜碰撞的炮孔壁峰值压力计算方法。结果表明,爆轰冲击理论计算结果接近实测值和数值模拟值;引入斜入射系数可计算爆轰波斜入射时孔壁压力,爆轰波碰撞在炸药与孔壁的分界面上,在不同的入射角度下,作用在孔壁的压力是不同的。孔壁压力与炸药特性、岩体特性、爆轰波曲率半径、爆轰波入射角等有关。

高海拔环境下运动装药的爆炸冲击波特性

为了研究高海拔环境下运动装药的爆炸冲击波传播特性,利用AUTODYN有限元软件,研究了不同海拔高度及其解耦对应的低温条件和低压条件对运动装药爆炸冲击波超压场的影响规律;建立了预测低温环境和低压环境下运动装药爆炸冲击波超压的理论计算模型,并通过试验数据和数值模拟进行了对比验证。结果表明,该计算模型可以有效预测不同低温、低压以及低温和低压耦合的高海拔环境下运动装药的爆炸冲击波超压;海拔高度从0升至10000 m,冲击波超压峰值平均减小35.6%,冲击波作用范围增加62.0%;随着环境温度降低,冲击波超压峰值平均增加0.43%,冲击波作用范围减小11.9%;随着环境压力降低,冲击波超压峰值平均减小36.4%,冲击波作用范围增加83.5%;不同海拔高度下装药运动速度引起的冲击波超压增大系数变化规律与解耦对应的低压条件影响规律基本相似;高海拔环境对运动装药爆炸冲击波的作用范围及超压的影响主要取决于低压条件,低温条件的影响程度较小。

致密砂岩气运移的临界动力学条件探讨

物理模拟是认识地下油气运移和聚集机理的重要方法和手段,为了更深入地认识深层条件下致密储层天然气运移的机理,以延安气田上古生界山西组致密砂岩气为例,设计了实验模型和边界条件。基于超低渗岩石多相渗流核磁共振在线模拟实验,探讨致密砂岩中天然气运移的临界压力、临界物性动力学条件,进而分析影响天然气运聚的控制因素。选取山西组不同砂岩类型包括石英净砂岩、富石英低塑性颗粒岩屑石英砂岩、富塑性颗粒岩屑砂岩和富凝灰质杂基石英砂岩样品,代表不同孔渗分布区间的岩石相储层,进行了恒定低注入流量、不同流速(流量)和不同压差充注实验。结果表明,致密砂岩储层的临界充注压力主要受岩石相和渗透率控制,渗透率较高的优势岩石相具有更低的临界充注压力,石英净砂岩天然气临界注入压力一般小于1.2 MPa,即使是物性很差的富塑性颗粒岩屑砂岩和富凝灰质杂基石英砂岩的天然气临界注入压力一般也小于1.5 MPa。同时,致密砂岩也没有绝对的天然气充注物性下限,但致密砂岩的充注效率、含气饱和度与储层物性,尤其是渗透率呈正相关,优势岩石相越发育、渗透率越高,充注效率和含气饱和度也越高。

A位有序四重钙钛矿氧化物:结构、物性和展望

A位有序四重钙钛矿氧化物AA′3B4O12具有丰富的物理性质和优异的材料性能,是当今凝聚态物理和材料科学的重要研究对象。相较于简单的ABO3型钙钛矿,在A位有序四重钙钛矿氧化物中,3/4的A位离子被过渡金属离子A′所取代,形成了1∶3的A/A′有序结构。因此,A位有序四重钙钛矿氧化物中的磁-电相互作用不再局限于B位子晶格内部,新颖的A′-A′、A′-B等磁-电相互作用也随之产生,从而展现出许多新现象和新物理机制,并为未来的实际应用提供了材料基础。围绕几种具有代表性的A位有序四重钙钛矿氧化物,回顾其研究脉络,对其晶体结构、物理性质和内在机理进行简单介绍,并对这类材料体系的研究方向和应用前景做出一些展望。

输氢管线钢氢脆敏感性影响因素综述

随着新能源产业的发展,采用大直径、高强度钢管输送氢气是未来氢能发展的必然趋势。分析了输氢管线钢在氢相容性试验中不同试验参数、输氢介质压力及组分、管线钢组织及强度、夹杂物和残余应力等对管线钢在高压氢气环境下的氢脆敏感性,讨论了降低输氢管线钢的氢脆敏感性的方法,提出了需要进一步重点研发的方向。

深孔轴向多段间隔装药孔壁冲击压力分布

为确定地下垂直长深孔爆破时合理的空气间隔长度,基于爆轰波理论,分析了多段间隔装药爆破条件下孔壁冲击压力随间隔长度变化的内在分布规律函数;依据Mises准则,得出了不同岩性时合理的间隔长度参考值,并通过数值模拟和现场爆破试验进行了验证。结果表明,空气间隔段孔壁冲击压力沿炮孔轴线从两端向中间骤降,但在中点周围略微增大,压力曲线呈两端大、中间小、中点周围略微凸起的“W”形对称分布。

中压补气对R404A冷冻系统性能特性研究

针对纯电动冷藏车冷冻系统在低温工况下出现的排气温度过高、制冷效能较低等问题,研发并搭建了一套采用变频换热风机的微通道换热器新型冷冻系统,研究车厢外环境温度持续增长时,中压补气技术对冷冻系统性能的影响。结果表明:当压缩机转速为4200r/min,库外温度为32℃,库内温度为-15℃,车内换热器风量为80%时,通过试验数据对比分析发现主阀的过热度和补阀的开度分别为5K和25%时冷冻系统制冷性能最佳;当冷冻系统主补阀开度为最佳时,变化库外环境温度发现,与不补气系统对比,系统采用中压补气时,排气温度降低了12.53%~33.80%,制冷量提高了8.38%~16.73%,压缩机功率增加了5.71%~13.07%,COP值上升了2.94%~4.17%。

深孔聚能预裂爆破切顶卸压机理与应用

为解决悬顶导致的煤柱及邻近巷道高应力和大变形问题,结合工作面顶板地质条件,提出深孔聚能预裂爆破切顶卸压专项方案,采用数值模拟及现场试验对卸压效果开展综合研究。研究结果表明,煤层顶板在切顶后垂直应力减幅为21.62%,预裂切顶措施可显著降低煤柱及邻近巷道围岩应力水平。试验发现,炮孔内轴向贯穿裂缝明显,可实现采空区顶板及时垮落。顶底板在切顶后累计位移量减幅达59.27%,巷道两帮及顶底板移近变形得到有效控制,煤柱垂直应力增量显著降低。实践证明,采用深孔聚能预裂爆破切顶卸压效果显著,可大幅提高作业效率,为类似矿压防治工程提供借鉴。