Internal Force Distribution in Steel-Concrete Composite Structure for Pylon of Cable-Stayed Bridge

Adopting a steel-anchor beam and steel corbel composite structure in the anchor zone on pylon is one of the key techniques for the design of Jintang bridge, a cable-stayed bridge in Zhoushan, China. In order to ensure the safety of the steel-concrete composite structure, a stud connector model for the joint section was put forward. Experiments were conducted to obtain the relation between load and slip of specimen, the failure pattern of stud connector, the yield bearing capacity and ultimate bearing capacity of a single stud, etc. The whole process of the structural behavior of the specimen was comprehensively analyzed. The features of the internal force distribution in the steel-concrete composite structure and the strain distribution of stud connector under different loads were emphatically studied. The test results show that the stud connector is applicable for the steel-concrete composite structure for pylon of Jintang bridge. The stud has a good ductility performance and a obvious yield process before its destruction. The stud connector basically works in a state of elasticity under a load less than the yield load.

The Continuum Analytical Method of Steel Frame- Reinforced Concrete Shear Wall Mixed Structure

The inter-story drift stiffness considered the semirigidity of beam and column joints connection, and P-Delta second order effect of steel frame parts in the mixed structure is presented in the paper. After considering on the influence of semirigidity between steel beams and steel columns, second order effect of beam-column members for steel frame and structural second order effect, the traditional continuum analytial method used in RC shear-frames wall structure is developed to steel frames-reinforced concrete shear wall mixed structure subject to horizontal load in this paper. A continuum approach, which is suitable for analyzing steel frames-reinforced concrete shear wall mixed structure subject to horizontal load, is presented. The method is relatively simple and more practical. It will be referred to structural design for steel frames-reinforced concrete shear wall mixed structure.

Seismic behavior of concrete filled steel tubular arch structures

Shaking table tests of a 1:10 scale arch model performed to investigate the seismic behavior and resistance of concrete filled steel tubular (CFT) arch structures are described in this paper. The El-Centro record and Shanghai artificial wave were adopted as the input excitation. The entire test process can be divided into three stages depending on the lateral brace configurations, i.e., fully (five) braced, two braces removed, and all braces removed. A total of 46 tests, starting from the elastic state to failure condition, have been conducted. The natural vibration frequencies, responses of acceleration, displacement and strain were measured. From the test results, it is demonstrated that the CFT arch structures are capable of resisting severe ground motions and that CFT arches offer a credible alternative to reinforced concrete arches, especially in regions of high seismic intensity.

Flexural Capacity Formula of Diaphragm-Through Joints of Concrete-Filled Square Steel Tubular Columns

Finite element analysis and parametric studies were performed to investigate the flexural capacity of the panel zone of diaphragm-through joints between concrete-filled square steel tubular columns and H-shaped steel beams. Through the comparisons of failure modes, load–displacement curves, and bearing capacity, it was found that the flexural capacity of the panel zone of diaphragm-through joints was determined by the tensile action and influence of the web of H-shaped steel beams, and the axial load should be taken into account. The steel tube and the diaphragm were the major parts of the joint that resisted the bending moment. The contribution of in-filled concrete had little influence on the flexural capacity of the panel zone of the joint and could be neglected. According to the results of these numerical studies, a formula that considered the influence of the web of H-shaped steel beams and the axial load was developed based on the yield lines in the diaphragm and the steel tube. The results of the proposed formula were in good agreement with the numerical data of this investigation. © 2017, Tianjin University and Springer-Verlag Berlin Heidelberg.

Application of laminated vierendeel truss in high-position transfer story structure

To meet the demands for large space and flexible compartmentation ofbuildings, laminated vierendeel trasses are adopted in high-position transfer story structures.First the bearing characteristics are analyzed, in which reasonable stiffness ratio of the upperchord, middle chord, and lower chord is derived. Then combined with an actual engineering model (1:8similar ratio), the static loading and pseudo-dynamic tests of two models for laminated vierendeeltrass used in transfer story structures are conducted, in which one model adopts reinforcedconcrete, and the other adopts prestressed concrete and shape steel concrete. Seismic behaviors areanalyzed, including inter-story displacement, base shear-displacement skeleton curves, andequivalent viscosity-damping curves. A program is programmed to carry out the elasto-plastic dynamicanalysis, and displacement time-history curves of the two models are derived. The test and analysisresults show that the laminated vierendeel trass with prestressed concrete and shape steel concretehas excellent seismic behaviors. It can solve the disadvantages of laminated vierendeel trussesused in transfer story structures. Finally, some design suggestions are put forward, which can bereferenced by similar engineering.

Identification of Connection Flexibility Effects Based on Load Testing of a Steel-Concrete Bridge

In the case of composite girders, an effective cooperation of both parts of the section is influenced by deformability of connectors. Limited flexural stiffness of welded studs, used commonly in bridge structures, does not provide full interaction of a steel beam and a concrete slab. This changes strain distribution in cross-sections of a composite girder and results in redistribution of internal forces in steel and concrete element. In the paper partial interaction index defined on the basis of a neutral axis position, which can be used for verification of steel-concrete interaction in real bridge structures rather than in specimens is proposed. The range of the index value changes, obtained during load testing of a typical steel-concrete composite beam bridge, is presented. The investigation was carried out on a motorway viaduct, consisting of two parallel structures. During the testing values of strains in girders under static and quasi-static loads were measured. The readings from the gauges were used to determine the index, characterizing composite action of the girders. Results of bridge testing under movable load, changing position along the bridge span is presented and obtained in-situ influence functions of strains and index values are commented in the paper.

Static behavior of semi-rigid thin-walled steel-concrete composite beam-to-column joints with bolted partial-depth flush end plate:experimental study

A new type of semi-rigid thin-walled steel-concrete composite beam-to-column joint has been proposed in this paper.Five semi-rigid composite beam-to-column joint specimens subjected to hogging moments under monotonic loading were tested to study the static behavior of this new type of joint.The main variable parameters for the five joint specimens were the longitudinal reinforcement ratio and the joint type.The experimental results designated that the magnitude of extension of the longitudinal reinforcement is the most important factor that influenced the moment-rotation characteristic of the new type of joint.The concrete slabs could resist 3.8%-19.1% of the total shear load applied to the cross-sections near the beam-to-column connection.The edge stiffened elements,such as the flange of the lipped I-section thin-walled steel beam,were capable of having considerable inelastic deformation capacity although they had comparatively large width-to-thickness ratios.The shear failure of the concrete cantilever edge strip must be taken into account in practical design because it has significant influence on the anchorage of the longitudinal reinforcement in the new type of external joints.

Evaluation of Current Design Practices on Estimation of Axial Capacity of Concrete Encased Steel Composite Stub Columns： A Review

This paper presents the design assessment of concrete encased I-sections composite column based approaches given in Eurocode, ACI Code, BS Code and AISC-LRFD. This study includes comparison of various design parameters and evaluation of design strength based on the procedures predicted in the various codes of practices. A practical example has been assumed and calculation has been shown to evaluate their potentiality in understanding in predicting the potentiality of various procedures. The obtained results based on the methods varies widely, because of the different design considerations adopted by the different codes. As such, they have hardly considered the effect of confinement of the concrete due to the presence of longitudinal reinforcements as well as lateral ties. The study has attempted to throw light on critical review and their potentiality in assessing the strength of such concrete encased composite column under purely axial loads.

A Comparative Analysis for Land Utilization: Steel and R/C Interlaced Structures

In architecture,interlace structural concept is considered as a new design approach for cosmopolitan cities with high density to minimize the land use and increase the interaction.With various architectural approach,land resources can be minimized by this interlace concept for residential complexes.Such buildings will eliminate the reduction of land resource problem and on the other side safety measures in structural design is incorporated by interlace concept of buildings.This new concept can be constructed steel or reinforced concrete.In this paper,an analytical approach has been presented for these buildings in architecture and structural design.In the research,design considerations were taken for interlaced structures with reinforced concrete and steel.Components of steel structure,isolated footing,and columns.This paper is presenting a step wise process for interlaced structures.They are identification of project area,layout and model preparation,analysis and design of concrete interlaced structure,analysis and design of steel interlaced structure,drafting of the plans and costing and estimation of the structures.Comparison of both reinforced concrete and steel structures were carried out.The main aim of the paper is to provide a comparison between steel and concrete interlaced structure.A cost estimation was carried out to determine optimum design and construction for interlaced structures.

装配式轻钢框架-轻钢骨架轻混凝土墙板结构抗震性能

为研究装配式轻钢框架-轻钢骨架轻混凝土墙板结构抗震性能,对1个足尺轻钢框架结构试件和3个足尺轻钢框架-轻钢骨架轻混凝土墙板结构试件进行了低周反复荷载下的抗震性能试验及理论分析,试件变量包括:2种装配构造,即内嵌式装配墙板、外贴式装配墙板;2种轻钢骨架轻混凝土墙板,即框架式轻钢骨架轻混凝土墙板、桁架式轻钢骨架轻混凝土墙板。研究了各试件的破坏特征和损伤演化过程,分析了结构滞回特性、承载力、变形能力、刚度退化、耗能性能和应变。结果表明:装配式轻钢框架-轻钢骨架轻混凝土墙板结构共同工作性能良好,其水平承载力相比轻钢框架提高了204.7%~210.4%,抗侧刚度提高了257.3%~512.5%,结构变形及耗能能力有显著提高;内嵌墙板的自攻钉连接构造以及外贴墙板的螺栓连接构造传力性能可靠,结构具备2道抗震防线的受力特征;基于简化塑性分析模型以及拉压杆软化桁架模型,对试件承载力进行了计算,计算结果与试验符合较好。

常泰长江大桥组合索塔锚固结构钢-混传剪构造足尺模型试验研究

常泰长江大桥索塔锚固结构采用钢箱-核芯混凝土组合结构,为研究该新型组合索塔锚固结构钢-混传剪构造的受力特性,进行钢-混传剪构造足尺模型试验研究。制作2个锚固结构足尺节段试验模型,通过压剪试验研究锚固结构的荷载~滑移曲线及应力、应变分布等受力特性,并通过有限元模型分析锚固结构的传力机理和各组件的内力分配比例,推导剪力钉剪力计算方法。结果表明:在2.14倍单索最大索力荷载作用下,锚固结构保持弹性状态,钢壁板未产生明显滑移,钢-混界面最大滑移不超过0.25 mm,该锚固结构中钢-混传剪构造至少具有2.14倍的安全系数;荷载作用下,剪力钉剪力从上至下逐渐增大,锚腹板附近底部3排剪力钉剪力较大,钢-混传剪构造至少存在剪力钉和界面摩擦力2种传剪机制,钢-混传剪构造的承载能力显著提高;钢-混传剪构造受力过程分为粘结力传力阶段和局部滑移阶段,剪力钉剪力分布不仅与沿剪切方向长度分布有关,也与荷载的大小线性相关。

钢-UHPC结合段PBL连接件和钢梁端面承压联合作用研究

钢-混结合段作为钢梁和混凝土连接为整体的核心部件,传力构件的受力性能对钢-混凝土结合段至关重要。为提高结合段的力学性能,进行了仅有钢梁端面承压、PBL连接件和两者联合作用3组推出试验。结果表明:3组试件最终破坏裂缝分布均为钢梁端面侧“八”字形分布;钢梁端面组(D组)试件破坏模式主要为UHPC的开裂破坏而失效,PBL连接件组(P组)和联合作用组(PD组)试件主要是贯穿钢筋的剪切破坏而失效;3组试件的荷载-滑移曲线均包含弹性、裂缝开展和屈服3个阶段,由于贯穿钢筋和UHPC榫具有抑制裂缝开展和提高试件延性的作用,P组和PD组试件裂缝开展阶段较D组更短,屈服阶段更长,延性更好。对荷载-滑移曲线进行拟合,提出了钢梁端面承压和PBL连接件承载力随滑移量变化的计算公式。引入滞后滑移差Δs_(j),当Δs_(j)=0~0.67 mm时,联合作用计算结果偏于安全。计算得到钢梁端面承压传力比例约为43%,PBL连接件传力比例约为57%,两者传力效果基本相当。利用UHPC作为外包混凝土时,建议采用承载能力更高的贯穿钢筋,以充分发挥UHPC的高强性能,从而提高结合段的承载能力。

波纹钢-混凝土复合结构高温压弯性态研究

波纹钢-混凝土复合结构因其强度较高且施工高效已逐渐应用于隧道支护中,但波纹钢板由于无混凝土的保护,在高温下性能劣化严重。依托云南省普洱市高山寨隧道,利用ABAQUS软件建立有限元模型进行数值模拟分析,研究波纹钢-混凝土复合结构在不同温度和不同偏心距正负弯矩作用下的多工况高温压弯性态。研究结果表明,随着温度的升高,波纹钢-混凝土复合结构中和轴逐渐上移,初始抗弯刚度和极限荷载逐渐下降;当温度>500℃时,结构性能降低幅度最大,宜将500℃作为结构重点关注温度。

大跨度钢-混结合梁悬索桥涡激振动控制指标体系研究

为保证已建桥梁发生涡激振动后桥梁结构的安全以及桥上行车和行人安全,提出综合考虑人员舒适性、结构受力和停车线形三方面的大跨度钢-混结合梁悬索桥涡激振动控制指标体系。该体系包含9项指标,分别为驾乘人员舒适度、驾乘人员晕动症、行人舒适度(狄克曼指标)、加劲梁强度、加劲梁应力、加劲梁挠度、桥面纵坡、竖曲线半径和停车视距。以武汉鹦鹉洲长江大桥为背景,分别计算了“限速”和“封桥”2个交通管制措施下9项指标对应的涡激振动振幅限值。在此基础上,将9项指标对应的涡激振动振幅限值的最小值作为涡激振动限值建议取值。结果表明:当该桥发生低阶竖弯涡激振动(VS1、VAS1)时,涡激振动的控制因素为加劲梁挠度指标;当大桥发生VAS2模态的竖弯涡激振动时,涡激振动由驾乘人员晕动症指标和行人舒适度指标共同控制;当大桥发生高阶竖弯涡激振动(VAS3、VAS4)时,涡激振动由行人舒适度指标控制。涡激振动控制指标体系及限值标准的计算框架可适用于不同桥型涡激振动限值的计算。

深中通道钢壳-混凝土组合沉管浇筑变形研究

深中通道沉管管节采用钢壳-混凝土组合结构形式,通过向空钢壳浇筑混凝土预制而成。为评估沉管管节施工后的整体变形,建立了热-结构顺序耦合的分析框架,基于ANSYS APDL及UFPs二次开发模块,分别建立了考虑水化度、日照辐射、大气温度变化的精细温度场模型和考虑混凝土硬化及收缩特性的结构分析模型。通过对足尺管节的温度及应变模拟结果与监测数据的对比,验证了有限元模型的可靠性。在此基础上,分析了日照辐射、大气温度变化等对于管节温度场的影响,同时分析了管节的整体变形模式,以及温度效应、混凝土收缩及自重三种因素对管节整体横向、纵向及竖向变形的影响。结果表明:管节施工过程的温度场表现为时变和空间分布的特征,格仓边部温度受外界气温变化和日照辐射的影响存在周期性波动,而格仓中部温度峰值主要受混凝土自身水化放热特性的控制;管节最终表现为顶板横向及纵向内收,竖向下挠,底板横向及竖向变形不显著;太阳辐射对于结构温度场影响较日气温变化更显著,建议在混凝土温度峰值预测中予以考虑,而日气温变化可采用日平均气温值予以简化;温度效应及材料收缩对管节横向及纵向整体变形影响显著,自重因素导致的变形在横向及纵向的比例为44.3%、11.7%,而在竖向所占比例达92.5%,因而温度效应及材料收缩在管节横向及纵向变形分析中不可忽视;该分析方法可适用于大体积混凝土等结构的温度效应的预测和评估。

装配式带夹芯保温槽型玻璃钢-钢板-槽钢-混凝土组合剪力墙轴压性能研究

提出一种装配式带夹芯保温槽型玻璃钢-钢板-槽钢-混凝土组合剪力墙,设计3个具有不同配筋形式和混凝土种类的墙板试件进行轴心受压试验,获得墙板在轴压作用下的破坏模式、荷载-位移曲线、荷载-应变曲线、承载力储备系数、延性系数、材料利用率等性能指标。通过ABAQUS有限元分析软件对墙板进行参数化分析,研究内嵌钢板强度和厚度对其轴压性能的影响。结果表明,墙板具有良好的承载力储备能力和延性性能;混凝土中掺入1%体积比的钢纤维可显著提高墙板内混凝土的抗拉性能,使混凝土强度得到更加充分的利用,布置钢筋可以显著提高墙板延性;墙板的承载力和延性随内嵌钢板厚度和强度的增加而增大,强度为Q355、厚度为4、6mm时,墙板材料利用率更高。提出适用于该类墙板的轴压承载力设计公式,考虑钢板屈曲和截面组合效应的墙板轴心受压承载力设计公式计算结果较精确。

Technological development and engineering applications of novel steel-concrete composite structures

In view of China's development trend of green building and building industrialization,based on the emerging requirements of the structural engineering community,the development and proposition of novel resourcesaving high-performance steel-concrete composite structural systems with adequate safety and durability has become a kernel development trend in structural engineering.This paper provides a state of the art review of China's cutting-edge research and technologies in steel-concrete composite structures in recent years,including the building engineering,the bridge engineering and the special engineering.This paper summarizes the technical principles and applications of the long-span bi-directional composite structures,the long-span composite transfer structures,the comprehensive crack control technique based on uplift-restricted and slip-permitted (URSP)connectors,the steel plate concrete composite (SPCC)strengthen technique,and the innovative composite joints.By improving and revising traditional structure types, the comprehensive superiority of steel-concrete composite structures is well elicited.The research results also indicate that the high-performance steel-concrete composite structures have a promising popularizing prospect in the future.

书夹型钢-混组合结构在桥梁加宽中的应用研究

为避免桥梁加宽时下部结构拓宽,减少新旧桥面纵向裂缝及铺装层损伤,提出一种以钢结构立柱及护栏、书夹式钢板、高强度螺栓为主要构件,超高性能混凝土(UHPC)为铺装层的书夹型钢-混组合结构进行桥梁加宽。为评估该组合结构在运营条件下的安全性,以厦门官浔溪大桥加宽工程为背景,通过实桥现场静载试验研究水平荷载作用下书夹型钢-混组合结构的力学性能,并与数值仿真结果进行对比,验证试验结果的可靠性。结果表明:实测结果与数值仿真结果吻合良好;书夹型钢-混组合结构关键部位荷载~位移曲线、荷载~应力曲线呈线性变化,钢结构最大拉应力约为材料屈服强度的75%,整体结构处于弹性工作阶段;螺栓预紧力有效减少了高强度螺栓的直剪作用,降低了剪切疲劳破坏风险;采用书夹型钢-混组合结构进行桥梁加宽可有效避免下部结构拓宽,改善新旧桥面纵向裂缝及铺装层损伤,具有较好的加宽效果。

斜拉桥V形钢塔-混凝土基座结合构造方式比选

某人行景观桥为空间异型钢塔斜拉桥,主塔中2根箱型钢柱在四棱台混凝土基座上方交汇呈非对称V形,钢柱轴线与其底端钢-混连接面不垂直,基座尺寸严格受制于河道防洪要求,使塔根-基座结合部构造方式设计具有挑战性。按照造价相当的标准初步拟定3种结合方案,采用ABAQUS软件分别建立相应的有限元模型,选取塔底支座反力中平面内外弯矩绝对值相加最大的组合进行模拟计算及其结果比较和对标检验。研究结果表明:承压-传剪组合式结合部可以大幅度减小桥塔根部、基座及其中锚箱的应力,使其合理满足相关规范要求。就塔根最大位移和应力幅而言,均为传剪式最大、组合式最小。组合式方案中承压板厚度较承压式减小1/3,应力虽有上升却未超限,材料利用率提高。承压式、特别是传剪式构造方案中,混凝土基座最大主拉应力远超规范限值,无法满足抗裂要求。传剪式方案中锚箱钢板Mises应力也超限22%,且与其竖向压应力和混凝土主拉应力的最大值处于同一位置。传剪式方案不适用的原因是,锚箱中侧面竖板间距太小,矩形板与柱壁连接屈从于不利构造特点,形成大转折。无论应力大小还是变形控制,组合式方案都值得优先选择。研究成果直接服务于本工程,对类似工程也有一定的参考价值。

Shear Behavior of Novel Prestressed Concrete Beam Subjected to Monotonic and Cyclic Loading

Prestressed steel ultrahigh-strength reinforced concrete(PSURC) beam is a new type of prestressed concrete beam, which not only has a considerable compressive strength attributed to the ultrahigh strength concrete, but also ensures a certain degree of ductility at failure due to the existence of structural steel. Five of these beams were monotonically tested until shear failure to investigate the static shear performance including the failure pattern, loaddeflection behavior, shear capacity, shear crack width and shear ductility. The experimental results show that these beams have superior shear capacity, crack control ability and shear ductility. To study the shear performance under repeated overloading, seven PSURC beams were loaded in cyclic test simultaneously. The overall shear performance of cycled beams is similar to that of uncycled beams at low load level but different at high load level. The shear capacity and crack control ability of cycled beams at high load level are reduced, whereas the shear ductility is improved. In addition, the influences of variables including the degree of prestress, stirrup ratio and load level on the shear performance of both uncycled and cycled beams were also discussed and compared, respectively.