Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifi...Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifications consisted in removing the frontal part of the grenade(fuse, ballistic cap and conductive cone) and introducing of the liner cavity filling made of polyacetal copolymer POM-C. The filings in the form of solid cones with three different heights(33%, 66% and 100% of H-the height of original PG-7VM liner) were placed inside of the hollow cone shaped charge liner. As opposed to the vast majority of previously published works(in which warhead optimization studies were focused on increasing of the depth of penetration in rolled homogeneous armor steel) the main aim of the presented modifications was to maximize the damage ratio(diameters of craters, inlet and outlet holes) of target perforated by shaped charge jet at the cost of the loss of part of the jet penetration capability. According to the best knowledge of the authors such approach to the use of the old PG-7VM warheads has not been analyzed so far. Taking into consideration high stock levels of PG-7VM warheads, and the fact that they are continuously being replaced by more efficient and more sophisticated high-explosive anti-tank warheads, it seems reasonable to look for alternate applications of the warheads withdrawn from the service. Thanks to the introduction of proposed modifications the warheads could be used by special forces or other assault units as directional mines or statically detonated cutting shaped charges as well as by combat engineers as universal charges used in various types of engineering or sapper works. The research included experimental penetration tests and their numerical reproduction in the LS-Dyna software with the simulation methodology defined and validated in previous works of the authors.Small differences(average error = 10-20%) were identified between the experimental and numerical results(dimensions of craters made in steel targets were compared) what confirmed the reliability of the modelling methodology and enabled its use for further optimization of the shapes of fillings. Within the analyzed variants of warheads modifications maximum diameters of penetration craters were obtained for the filling of the height of h = 2/3H. The diameters of holes in individual steel plates were increased by 164%, 70%, 65%(for the first, second and third plate, respectively) in relation to the variant without filling. The results of the study indicated that with the use of different materials of fillings and their various heights it is possible to control the shape of penetration craters pierced in the steel targets.展开更多
The story of iron and steel production in China is one of constant and spectacular rise,but no one seemns to know yet if the story will hawe a happy ending.
针对钢渣体积稳定性差、钢渣-沥青混合料道路过早开裂的问题,采用二氧化硅胶体溶液对钢渣进行浸泡改性处理,通过力学性能测试、扫描电子显微镜(scanning electron microscope,SEM)检测、路用性能测试等方法研究了改性钢渣的物理力学性...针对钢渣体积稳定性差、钢渣-沥青混合料道路过早开裂的问题,采用二氧化硅胶体溶液对钢渣进行浸泡改性处理,通过力学性能测试、扫描电子显微镜(scanning electron microscope,SEM)检测、路用性能测试等方法研究了改性钢渣的物理力学性能、改性钢渣-沥青混合料的性能和钢渣的改性机理,并引入灰靶理论决策方法,综合改性钢渣-沥青混合料的各项性能指标,确定钢渣的最佳改性方案。结果表明:钢渣改性后,物理力学性能明显提高;钢渣的改性浓度越大,沥青混合料的高温性能越佳;延长钢渣的改性时间,沥青混合料的低温抗裂性能提高;且钢渣改性之后,沥青混合料的水稳定性能显著提高。基于灰靶决策理论,最终确定钢渣的最佳改性方案是在改性浓度(溶液质量分数)为3%的溶液下浸泡24 h。展开更多
Gives a new technique to measure the dynamic deformation behavior and strain development of a hollow steel projectile during its penetration of concrete targets. Direct strain measurement was performed by applying str...Gives a new technique to measure the dynamic deformation behavior and strain development of a hollow steel projectile during its penetration of concrete targets. Direct strain measurement was performed by applying strain gages attached to the inner walls of the hollow projectile, linked with on-board testing and storage recorder. This on-board test-record system is easy to operate, cost-effective and can provide reasonable, accurate and detailed information. Obverse ballistic experiments were carried out on ogival-nose hollow projectiles normally impacting concrete targets at velocities from 150 m/s to 300 m/s. The deformation process of projectiles was measured, recorded and played back. Profiles of voltage-time relationship were successively obtained and transfered to strain-time relationship with the aid of calibration tables. It was found that projectiles go through a series of compression and tension deformations intermittently. Relationships between strain development and projectile deformation process were discussed.展开更多
Adopting the load and resistance factor design format, the design method for steel jaeket platform structures is developed. Firstly, the limit state equations and design format for steel jacket platform structures are...Adopting the load and resistance factor design format, the design method for steel jaeket platform structures is developed. Firstly, the limit state equations and design format for steel jacket platform structures are introduced. Then, the ratio of live load effect to dead load effect is estimated. The target reliabilities for design of offshore structures in China offshore area are calibrated by past practice in API RP2A-WSD code. The load and resistance factors are optimized by minimizing the difference within the target reliability and the resulting reliability over the range of load effect ratios. Considering the concurrence of different loads, load combination factors are obtained through an optimization process, and the relation between the load combination factor and load correlation coefficient is established. Finally, the design formulae for steel jacket structures in China offshore area are recommended.展开更多
文摘Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifications consisted in removing the frontal part of the grenade(fuse, ballistic cap and conductive cone) and introducing of the liner cavity filling made of polyacetal copolymer POM-C. The filings in the form of solid cones with three different heights(33%, 66% and 100% of H-the height of original PG-7VM liner) were placed inside of the hollow cone shaped charge liner. As opposed to the vast majority of previously published works(in which warhead optimization studies were focused on increasing of the depth of penetration in rolled homogeneous armor steel) the main aim of the presented modifications was to maximize the damage ratio(diameters of craters, inlet and outlet holes) of target perforated by shaped charge jet at the cost of the loss of part of the jet penetration capability. According to the best knowledge of the authors such approach to the use of the old PG-7VM warheads has not been analyzed so far. Taking into consideration high stock levels of PG-7VM warheads, and the fact that they are continuously being replaced by more efficient and more sophisticated high-explosive anti-tank warheads, it seems reasonable to look for alternate applications of the warheads withdrawn from the service. Thanks to the introduction of proposed modifications the warheads could be used by special forces or other assault units as directional mines or statically detonated cutting shaped charges as well as by combat engineers as universal charges used in various types of engineering or sapper works. The research included experimental penetration tests and their numerical reproduction in the LS-Dyna software with the simulation methodology defined and validated in previous works of the authors.Small differences(average error = 10-20%) were identified between the experimental and numerical results(dimensions of craters made in steel targets were compared) what confirmed the reliability of the modelling methodology and enabled its use for further optimization of the shapes of fillings. Within the analyzed variants of warheads modifications maximum diameters of penetration craters were obtained for the filling of the height of h = 2/3H. The diameters of holes in individual steel plates were increased by 164%, 70%, 65%(for the first, second and third plate, respectively) in relation to the variant without filling. The results of the study indicated that with the use of different materials of fillings and their various heights it is possible to control the shape of penetration craters pierced in the steel targets.
文摘The story of iron and steel production in China is one of constant and spectacular rise,but no one seemns to know yet if the story will hawe a happy ending.
文摘针对钢渣体积稳定性差、钢渣-沥青混合料道路过早开裂的问题,采用二氧化硅胶体溶液对钢渣进行浸泡改性处理,通过力学性能测试、扫描电子显微镜(scanning electron microscope,SEM)检测、路用性能测试等方法研究了改性钢渣的物理力学性能、改性钢渣-沥青混合料的性能和钢渣的改性机理,并引入灰靶理论决策方法,综合改性钢渣-沥青混合料的各项性能指标,确定钢渣的最佳改性方案。结果表明:钢渣改性后,物理力学性能明显提高;钢渣的改性浓度越大,沥青混合料的高温性能越佳;延长钢渣的改性时间,沥青混合料的低温抗裂性能提高;且钢渣改性之后,沥青混合料的水稳定性能显著提高。基于灰靶决策理论,最终确定钢渣的最佳改性方案是在改性浓度(溶液质量分数)为3%的溶液下浸泡24 h。
文摘Gives a new technique to measure the dynamic deformation behavior and strain development of a hollow steel projectile during its penetration of concrete targets. Direct strain measurement was performed by applying strain gages attached to the inner walls of the hollow projectile, linked with on-board testing and storage recorder. This on-board test-record system is easy to operate, cost-effective and can provide reasonable, accurate and detailed information. Obverse ballistic experiments were carried out on ogival-nose hollow projectiles normally impacting concrete targets at velocities from 150 m/s to 300 m/s. The deformation process of projectiles was measured, recorded and played back. Profiles of voltage-time relationship were successively obtained and transfered to strain-time relationship with the aid of calibration tables. It was found that projectiles go through a series of compression and tension deformations intermittently. Relationships between strain development and projectile deformation process were discussed.
文摘Adopting the load and resistance factor design format, the design method for steel jaeket platform structures is developed. Firstly, the limit state equations and design format for steel jacket platform structures are introduced. Then, the ratio of live load effect to dead load effect is estimated. The target reliabilities for design of offshore structures in China offshore area are calibrated by past practice in API RP2A-WSD code. The load and resistance factors are optimized by minimizing the difference within the target reliability and the resulting reliability over the range of load effect ratios. Considering the concurrence of different loads, load combination factors are obtained through an optimization process, and the relation between the load combination factor and load correlation coefficient is established. Finally, the design formulae for steel jacket structures in China offshore area are recommended.
