Effect of titanium on the sticking of pellets based on hydrogen metallurgy shaft furnace:Behavior analysis and mechanism evolution

Direct reduction based on hydrogen metallurgical gas-based shaft furnace is a promising technology for the efficient and low-carbon smelting of vanadium-titanium magnetite.However,in this process,the sticking of pellets occurs due to the aggregation of metal-lic iron between the contact surfaces of adjacent pellets and has a serious negative effect on the continuous operation.This paper presents a detailed experimental study of the effect of TiO2 on the sticking behavior of pellets during direct reduction under different conditions.Results showed that the sticking index(SI)decreased linearly with the increasing TiO2 addition.This phenomenon can be attributed to the increase in unreduced FeTiO3 during reduction,leading to a decrease in the number and strength of metallic iron interconnections at the sticking interface.When the TiO2 addition amount was raised from 0 to 15wt%at 1100°C,the SI also increased from 0.71%to 59.91%.The connection of the slag phase could be attributed to the sticking at a low reduction temperature,corresponding to the low sticking strength.Moreover,the interconnection of metallic iron became the dominant factor,and the SI increased sharply with the increase in re-duction temperature.TiO2 had a greater effect on SI at a high reduction temperature than at a low reduction temperature.

Effects of Plant Spacing and Finger Sticking Area Settings for Machine Transplanting on Yield of Double-season Early Rice

The effects of rice transplanters＇ transplanting settings（plant spacing and finger sticking area） on rice yield were investigated in two early-season rice cultivars：hybrid rice cultivar（Zhuliangyou 819） and conventional rice cultivar（Zhongjiazao 17）.The results showed that,different transplanting settings resulted in different numbers of transplanted basic seedlings,and the rice yield was significantly correlated with the number of transplanted basic seedlings.The number of transplanted basic seedlings increased with the decrease of plant spacing and the increase of finger sticking area.The rate of lost hills of machine transplanting decreased with the increase of finger sticking area.The leaf area index and amount of dry matter accumulation were highly correlated with the number of transplanted basic seedlings.The average yield of the rice transplanted with a plant spacing of11.5 cm was higher than that with a plant spacing of 13.8 cm.In the field transplanted with the rice under the plant spacing of 13.8 cm,the rice yield increased with the increase of finger sticking area,and the finger sticking area of 2.23 cm2 showed the highest rice yield of 8 174.16 kg/hm2 of Zhuliangyou 819 and 7 925.54kg/hm2 of Zhongjiaozao17.In the field transplanted with the rice under the plant spacing of 11.5 cm,the rice yield was the highest with the finger sticking area of 1.83 cm2,and then decreased with the large finger sticking area.Under the plant spacing of 11.5 cm,the highest rice yields of Zhuliangyou 819 and Zhongjiaozao17 were 8 492.94 kg/hm2 and 8 000.23 kg/hm2,respectively.Therefore,the preferred machine transplanting settings for double-season early rice are a plant spacing of11.5 cm and a finger sticking area of 1.83 cm2,while the finger sticking area should be increased to 2.23 cm2 for conventional rice cultivars.

APPLICATION OF 2-D MOIRE INTERFEROMETRYOF STICKING FILM IN HUMAN TIBIA MEASUREMENT

This paper makes use of the method of testing and measuring the human body tibia by using2-D moire interferometry of sticking film. hased on the J'--y direction moire patterns recorded synchronously by 2-D optical path,the elastic constant,strain and displacement of the tibia are measured.Compared with the electric measuring method the error is samll and the sensitivity is high.

Test research on sticking mechanism during hot rolling of SUS 430 ferritic stainless steel

The sticking phenomenon during hot rolling of SUS 430 ferritic stainless steel was investigated by means of a two-disc type high-temperature wear tester. The test results indicate that sticking particles on the surfaces of high chromium steel （HiCr） and high-speed steel （HSS） rolls undergo nucleation, growth, and saturation stages. Grooves on the roll surface generated by grinding provide nucleation sites for sticking particles. The number of sticking particles on the HiCr roll surface is greater than that on the HSS roll surface. The average surface roughnesses （Ra） of HiCr and HSS rolls change from 0.502 and 0.493 μm at the initial stage to 0.837 and 0.530 μm at the saturation stage, respectively. The test further proves that the sticking behavior is strongly dependent on roll materials, and the HSS roll is more benefi- cial to prevent particles sticking compared with the HiCr roll under the same hot-rolling conditions.

Sticking of iron ore pellets in direct reduction with hydrogen and carbon monoxide:Behavior and prevention

A series of reduction experiments of iron ore pellets with hydrogen,carbon monoxide and their mixture were carried out in a laboratory scale shaft furnace.The sticking behavior accompanying reduction of iron ore pellets was investigated.And morphology of the sticking interface forming during reduction was analyzed by SEM equipped with EDS.In order to evaluate the effects of the temperature and gas composition on sticking properties,reduction of iron ore pellets were conducted at 800-1000 ℃.The results show that the sticking strength of the pellets increases with temperature,however,decreases with hydrogen content in reducing gas.For an efficient shaft furnace operation in direct reduction(DR),relative prevention of sticking such as coating of pellets was also developed to solve sticking problem.The results show that CaO is a suitable material for the coating method.

A New Method for Predicting Wall Sticking Occurrence Temperature of High Water Cut Crude Oil

In crude oil transportation, adhesion of oil on pipe wall can cause partial or total blockage of the pipe. This process is significantly affected by wall sticking occurrence temperature(WSOT). In this work, an efficient approach for estimating WSOT of high water-cut oil, which can agree well with the actual environment of multiphase transportation pipeline, is proposed. Based on the energy dissipation theory, it is possible to make comparison of average shear rates between the stirred vessel and the flow loop. The impacts of water content and shear rate on WSOT are investigated using the stirred vessel and the flow loop. Good agreement has been observed between the stirred vessel and the flow loop results with the maximum and the average absolute deviations equating to 3.30 °C and 2.18 °C, respectively. The development of gathering scheme can enjoy some benefits from this method.

Wall Sticking of High Water-Cut, Highly Viscous and High Gel-Point Crude Oil Transported at Low Temperatures

Some crude oils with high water cut have the capability to flow below the oil gel point, while the oil particles adhere to the pipe wall in the form of paste, also called "wall sticking". Wall sticking is a serious problem during the pipeline transportation, leading to partial or total blockage of the pipeline and energy wastage. In this paper, a series of laboratory flow loop experiments were conducted to observe the wall sticking characteristics of crude oil with high water cut, high viscosity and high gel point at low transportation temperatures. The effects of shear stress and water cut on the wall sticking rate and occurrence temperature were investigated. Experimental results indicated that the wall sticking rate and occurrence temperature were lower under stronger shear stress and higher water cut conditions. A criterion of wall sticking occurrence temperature(WSOT) and a regression model of wall sticking rate were then established. Finally, the software was developed to calculate the pressure drop along the pipelines of crude oils with high water-cut. It was able to predict the wall sticking thickness of gelled oil and then calculate the pressure drop along the pipelines. A typical case study indicated that the prediction results obtained from the software were in agreement with actual measured values.

Influence of Oil and Water Components on Wall-sticking Occurrence Temperature in High Water-cut Crude Oil Pipeline

To study the wall-sticking phenomenon and prevent pipeline blockage accidents,two analytical methods are used to evaluate the influence of different crude oil components on the wall-sticking occurrence temperature(WSOT).The WSOT and the interactions among oil,water,and surface solids are measured and calculated by various devices under different values of the wax content,water pH,and salinity.The results show that there is greater correlation between the wax content and WSOT than between resins/asphaltenes and WSOT.Furthermore,the wax content,water pH,and salinity have different effects on WSOT.There is generally a positive correlation between wax content and WSOT,whereas the maximum WSOT occurs when the water pH is in the range 5.7–6.5,and decreases under more acidic or alkaline conditions.As the salinity increases,WSOT decreases slightly,but quickly becomes saturated.In terms of interactions,variations in the interfacial tension and adhesion work with pH and salinity are consistent with that of WSOT,while the contact angle exhibits the opposite relation.

Operational procedures of auricular point sticking technology

As an external treatment technique of traditional Chinese medicine(TCM),auricular point sticking,which is rooted in holographic biology theory and TCM viscera and meridian theory,is a safe and effective treatment method.This article introduces the technology overview and development process.The auricular point sticking technique for constipation is taken as an example to specify the basic requirements,assessment,operational points,acupoint selection and matters needing attention during the implementation of the auricular acupressure technique,providing a reference for the operating procedures of this technique in the clinical treatment of other diseases such as insomnia,diarrhea,colds,hypertension,headache,and dysmenorrhea.

Numerical Simulation and Prediction for Sticking Type Breakout Behavior in Slab Contiuous Casting

A two-dimensional heat transfer model was developed to calculate the mould wall temperature field under normal operations condition and to determine its changing behavior when breakout occured. On the numerical simulation of sticking type breakout process and the breakout related wall temperature evolution, parameters of prediction were suggested.

An Artificial Intelligence Algorithm for the Real-Time Early Detection of Sticking Phenomena in Horizontal Shale Gas Wells

Sticking is the most serious cause of failure in complex drilling operations.In the present work a novel“early warning”method based on an artificial intelligence algorithm is proposed to overcome some of the known pro-blems associated with existing sticking-identification technologies.The method is tested against a practical case study(Southern Sichuan shale gas drilling operations).It is shown that the twelve sets of sticking fault diagnostic results obtained from a simulation are all consistent with the actual downhole state;furthermore,the results from four groups of verification samples are also consistent with the actual downhole state.This shows that the pro-posed training-based model can effectively be applied to practical situations.

CLINICAL EFFECTS ON 149 CASES OF INFANTILE DIARRHEA TREATED WITH RAPID-STICKING MOXATHERAPY Attaching 35 contrasted cases with western medicine

Of 149 cases.infantile diarrhea were treated with Zhou’s multiapplied rapid-sticking herbomoxa-pen.The main acupoints selected were Auriculoapex,Tianshu(ST 25),Zusanli(ST 36),Shenshu(BL 23),etc.TWO groups were observed,32 cases from the 149 cases as therapid-sticking moxatherapy(RSMT)group who suffered from the acute diarrhea without any thera-peutics before,and the other 35 cases with western medicine as the control group.Results showedthat the recovering rate and the average therapeutic course of healing in RSMT group were higher andshorter than that in control one(P【0.05;P【0.01),even without marked difference of the total ef-fective rates between the two groups(P】0.05).Of 149 cases with RSMT,the therapeutic effect onacute ones was better than those on delayed and chronic ones(P【0.05),yet the difference was notmarked in therapeutic effects between the etiological causes of infections and non-infections(P】 0.0.5).It is therefore worthy of popularizing RSMT due to its remarked curative results without anyside-effect,simply-manipulated and well-accepted features.

Assessment of Knowledge, Attitude and Practices among Healthcare Workers in a Tertiary Care Hospital on Needle Stick Injury

Purpose: Needle-stick injury (NSI) is one of the most potential occupational hazards for healthcare workers because of the transmission of blood-borne pathogens. As per recent data, around 30 lakh healthcare workers sustain Needle stick injuries each year. This study was conducted to assess healthcare workers’ knowledge, attitude and practices regarding needle stick injury. Materials & Methods: A cross-sectional study was conducted in a Tertiary Care Hospital over the period of 3 months. The study population consisted of Intern Doctors, Post Graduate resident Doctors, Staff Nurses, laboratory technicians of Government Medical College and New Civil Hospital, Surat (n = 300). The data were collected using a self-administered questionnaire via the means of Google Forms. Questionnaire was made with prior review literature. The data obtained were entered and analysed in Microsoft Excel. Results: The prevalence of NSI in our study was 46%, with a higher prevalence among the PG residents (72%). Overall scores regarding knowledge and attitude were better in PG residents (knowledge score > 7 in 71% and Attitude Score > 7 in 68% of PG Residents). Even though the PG residents scored highest in the knowledge category, the majority of them suffered needle stick injuries as a result of poor practice scores. Among those who had NSI (n = 139/300), 70% of study participants had superficial injuries, only 9% reported the incident, 18% got medical attention within 2 hours of the incident, and 7% followed up to recheck their viral markers status. Most incidents of NSI were due to hypodermic needles while recapping needles. Conclusion: Exposure to needle stick injuries and their underreporting remains a common problem. It is imperative that healthcare workers receive regular training on the proper handling of sharp objects. We can also draw the conclusion that preventing NSIs requires putting knowledge into practice.

双摩擦块制动系统不同相对位置分布对stick-slip振动的影响

利用定制试验装置,研究圆形双摩擦块不同相对位置分布对制动系统摩擦学行为和动力学行为的影响,并采用有限元方法分析了摩擦块表面接触应力分布特点,探讨了不同相对位置分布与界面接触行为、摩擦磨损以及stick-slip振动之间的关联。综合试验结果和仿真分析结果表明:双摩擦块制动系统不同相对位置分布显著影响了制动系统界面接触压力分布及摩擦块表面磨损特性,使系统产生不同形式的stick-slip振动。在该试验下,沿摩擦盘径向分布的两个摩擦块表面磨损轻微,接触压力分布相对均匀和具有较小的stick-slip振动幅度。因此,合理设计摩擦块间的排布可以有效抑制盘块摩擦界面stick-slip振动,减轻摩擦块的磨损,减小系统部件振荡,从而提高摩擦系统稳定性。研究结果对汽车和火车(特别是高速列车)制动器的设计有较重要的参考价值。

Characteristics of Water Absorption and the Loss of Dust-Sticking Agent

The development of NCZ-1 dust-sticking agent was first intreduced in china. The speed of water absorption of dust-stick-ing agent was measured and studied on mining site and in laboratory, and then the law of water absorption of dust-sticking agent was analyzed. In addition, the mathematical model of the loss rate of dust-sticking agent was established by the application of fluid mechanics theory, and the method of determining the sprinkle parameters of dust-sticking agent was obtained. Through practical verifi-cation, it is found that the error of this mathematical model is less than 10%. So it can be used in the field.

Clinical Effect of Auricular Point Sticking in Patients with Lung Cancer Receiving Chemotherapy

Objective:To discuss and analyze the clinical effect of auricular point sticking in lung cancer chemotherapy.Methods:Sixty-two patients with lung cancer treated with chemotherapy in Suqian Traditional Chinese Medicine Hospital of Jiangxi Province were selected for case evaluation and analysis.The time span of the research was from June 2020 to June 2021.The patients were divided into two groups:a study group(n=31)and a control group(n=31)based on their medical record numbers.All the patients were treated with conventional western medicine before and after chemotherapy to prevent adverse reactions;however,the patients in the study group were also treated with auricular point sticking in addition to the fonner.The relevant indexes of the two groups were compared.Results:The incidence of adverse reactions was significantly lower in the study group compared to the control group(P<0.05);the rate of symptomatic relief of the patients in the study group was higher than that of the control group(P<0.05);the stress response indexes toward chemotherapy of the study group were better than those of the control group(P<0.05)・Conclusion:Auricular point sticking for patients with lung cancer who are receiving chemotherapy can reduce the incidence of adverse reactions,alleviate clinical symptoms,such as chest distress,asthma,and poor appetite,significantly alleviate stress response caused by chemotherapy,as well as promote the treatment effect;thus,it is worthy of promotion.

Effect of Mouth Opening Training Stick Combined with Oral Massage on Mouth Opening Difficulty in Head and Neck Cancer Patients after Treatment

Objective: To study the application effect of mouth-opening training sticks combined with oral massage on patients with mouth-opening difficulty after treatment for head and neck cancer. Methods: Using convenient sampling, 60 patients with mouth-opening difficulty after treatment for head and neck cancer admitted to the Oncology Department from February 2022 to October 2023 were selected for a 2-week exercise and nursing program. The patients were divided into a control group (February 1, 2022 to November 30, 2022) and an observation group (December 1, 2022 to October 31, 2023), with 30 patients in each group. The control group underwent routine mouth-opening functional exercises combined with cork for oral support training, while the observation group underwent routine mouth-opening functional exercises combined with oral massage and mouth-opening training sticks for oral support training. The mouth-opening degree, mouth-opening difficulty level, comfort level, compliance, and quality of life were observed in both groups. Results: Before the intervention, there were no statistically significant differences in mouth-opening degree and mouth-opening difficulty level between the two groups (P > 0.05). After the intervention, the mouth-opening degree, mouth-opening difficulty level, oral comfort level, compliance, and QLICP-HN scores in the observation group were all better than those in the control group, with statistically significant differences (P < 0.05). Conclusion: The combination of mouth-opening training sticks and oral massage with mouth-opening functional exercises can effectively improve the degree of mouth-opening difficulty, enhance oral comfort, increase compliance with mouth-opening exercises, and improve quality of life.

供需中的Hockey-stick现象分析及对策研究

许多公司的产品需求在连续而固定的周期会出现前低后高,即 Hockey-stick 现象,这种现象普遍存在于供应链之中并困扰着许多的企业管理者.不认为其产生的原因是公司对销售人员的周期性考评的传统观点,并以快速消费品行业为背景,通过建立模型,得出了这种现象主要是公司普遍采用的总量折扣(Volume Discounts)价格政策导致的结论,并提出了公司可以通过多产品组合定价等方法缓和这个问题,最后通过一个实例证实了文章的观点.

STUDY ON SLAG DETACHABILITY AND STICK SLAG MECHANISM OF SSFCE

In the paper, the effects of linear expansion coefficient and basic index of melting slag on the detachability of self shielded flux cored electrode (SSFCE) are investigated. An equation is obtained on the principles of ceramics and mineralography which predict the detachability of basic SSFCE. In addition, stick slag mechanism of SSFCE is analyzed.

带基础隔震器结构的Stick-slip运动模型

带基础隔振器结构的Ｓｔｉｃｋ－ｓｌｉｐ运动研究是一个很年轻的课题．有关文献指出：带可滑动基础的结构存在Ｓｔｉｃｋ－ｓｌｉｐ运动的可能，它将导致结构失稳以及由此引起疲劳破坏，因此该类结构的Ｓｔｉｃｋ－ｓｌｉｐ运动研究是有价值的．据此，调查了在地震作用下带滑动基础或基础隔振器结构，并建立其Ｓｔｉｃｋ－ｓｌｉｐ运动的离散动力学模型，指出了系统的复杂的非线性特性．