Investigations of methane adsorption characteristics on marine-continental transitional shales and gas storage capacity models considering pore evolution

Methane adsorption is a critical assessment of the gas storage capacity(GSC)of shales with geological conditions.Although the related research of marine shales has been well-illustrated,the methane adsorption of marine-continental transitional(MCT)shales is still ambiguous.In this study,a method of combining experimental data with analytical models was used to investigate the methane adsorption characteristics and GSC of MCT shales collected from the Qinshui Basin,China.The Ono-Kondo model was used to fit the adsorption data to obtain the adsorption parameters.Subsequently,the geological model of GSC based on pore evolution was constructed using a representative shale sample with a total organic carbon(TOC)content of 1.71%,and the effects of reservoir pressure coefficient and water saturation on GSC were explored.In experimental results,compared to the composition of the MCT shale,the pore structure dominates the methane adsorption,and meanwhile,the maturity mainly governs the pore structure.Besides,maturity in the middle-eastern region of the Qinshui Basin shows a strong positive correlation with burial depth.The two parameters,micropore pore volume and non-micropore surface area,induce a good fit for the adsorption capacity data of the shale.In simulation results,the depth,pressure coefficient,and water saturation of the shale all affect the GSC.It demonstrates a promising shale gas potential of the MCT shale in a deeper block,especially with low water saturation.Specifically,the economic feasibility of shale gas could be a major consideration for the shale with a depth of<800 m and/or water saturation>60%in the Yushe-Wuxiang area.This study provides a valuable reference for the reservoir evaluation and favorable block search of MCT shale gas.

Structures and oxygen storage capacities of CeO_2-ZrO_2-Al_2O_3 ternary oxides prepared by a green route:supercritical anti-solvent precipitation

CeO2-ZrO2-Al2O3 ternary oxides were successfully prepared by a green route of supercritical anti-solvent precipitation with supercritical CO2 as anti-solvent and methanol as solvent. The structures and oxygen storage capacities of these ternary oxides were characterized by XRD, Raman spectra and oxygen storage capacity measurements. It was found that Al3＋ and Zr4＋ inserted into CeO2 lattice, forming CeO2-ZrO2-Al2O3 solid solution. The concentration of aluminium isopropoxide in the solution affected the concentration of oxygen vacancy and the distortion of oxygen sublattice which were responsible for the oxygen storage capacity. The rapidest oxygen uptake/release rate and maximum total oxygen storage capacity （122.0 mmolO2/molCeO2） were obtained with the aluminitun isopropoxide concentration at 0.2 wt.% in the solution.

Research on the feasibility of storage and estimation model of storage capacity of CO_(2)in fissures of coal mine old goaf

The concept of the carbon cycle in the old goaf of a coal mine based on CO_(2)utilization and storage was put forward adhering to the principle of low-carbon development,utilization of space resources in old goafs,and associated gas resources development.Firstly,the evolution characteristics of overburden fissures in the goaf of the case was studied using a two-dimensional physical similarity simulation test,the sealing performance of the caprocks after stabilization was analyzed,and the fissures were counted and classi-fied.Then,the process of gaseous CO_(2)injection in the connected fissure was simulated by Ansys Fluent software,and the migration law and distribution characteristics of CO_(2)under the condition of gaseous CO_(2)injection were analyzed.Finally,the estimation models of free CO_(2)storage capacity in the old goaf were constructed considering the proportion of connected fissure and the effectiveness of CO_(2)injection.The CO_(2)storage capacity in the old goaf of the case coal mine was estimated.The results showed that a caprock group of“hard-thickness low-permeability hard-thickness”was formed after the caprock-fissures system in the goaf of the case tended to be stable vertically.The connected fissure,occlude cracks,and micro-fractures in the goaf accounted for 85.5%,8.5%,and 6%of the total fissures,respectively.Gaseous CO_(2)first migrated to the bottom of the connected fissure after CO_(2)was injected into the goaf,then spread horizontally along the bottom of the connected fissure after reaching the bottom,and finally spread longitudinally after filling the bottom of the entire connected fissure.The theoretical and effective storage capacities of free CO_(2)at normal temperature and pressure in the old goaf of the case were 9757 and 7477 t,respectively.The effective storage capacity of free CO_(2)at normal temperature and pressure in the old goaf after all minefield mined was 193404 t.The research can provide some reference for the coal mining industry to help the goal of“carbon peaking and carbon neutrality”.

Biomass Homogeneity Reinforced Carbon Aerogels Derived Functional Phase-Change Materials for Solar–Thermal Energy Conversion and Storage

We deviseda functional form stable compositephase-change materials(PCMs)toachieve a three-dimensional(3D)interconnectedporous carbon aerogel structure for encapsulating polyethyleneglycol(PEG).Anovelhomogeneity reinforced carbonaerogel witha well-interconnected porous structure was constructed bycombining a flexible carbonresource from biomass guar gum with hard-brittle carbonfrom polyimide,to overcome severeshrinkage andpoor mechanical performance of traditionalcarbon aerogel.Thesupportingcarbon aerogel-encapsulated PEG produced thenovel composite PCMswithgood structure stability andcomprehensive energy storage performance.Theresults showed thatthecomposite PCMsdisplayed awell-defined 3Dinterconnected structure,and theirenergy storage capacities were 171.5 and169.5 J/g,which changed onlyslightlyafter 100 thermalcycles,andthe compositescould maintainthe equilibrium temperature at50.0−58.1℃ for about 760.3 s.The thermal conductivityofthe compositescould reach0.62 W m^(−1) K^(−1),which effectively enhanced the thermalresponse rate.And thecomposite PCMs exhibited good leakage-proof performance andexcellent light–thermal conversion.The compressive strengthof thecomposite PCMscan improveupto 1.602 MPa.Results indicatethatthisstrategy canbe efficiently usedtodevelop novel composite PCMswithimproved comprehensive thermalperformance and high light–thermal conversion.

A CO_(2) storage potential evaluation method for saline aquifers in a petroliferous basin

According to the requirements for large-scale project implementation, a four-scale and three-level CO_(2)storage potential evaluation method is proposed for saline aquifers in a petroliferous basin in China, considering geological,engineering and economic factors. The four scales include basin scale, depression scale, play scale and trap scale, and the three levels include theoretical storage capacity, engineering storage capacity, and economic storage capacity. The theoretical storage capacity can be divided into four trapping mechanisms, i.e. structural & stratigraphic trapping, residual trapping, solubility trapping and mineral trapping, depending upon the geological parameters, reservoir conditions and fluid properties in the basin. The engineering storage capacity is affected by the injectivity, storage security pressure, well number, and injection time.The economic storage capacity mainly considers the carbon pricing yield, drilling investment, and operation cost, based on the break-even principle. Application of the method for saline aquifer in the Gaoyou sag of the Subei Basin reveals that the structural & stratigraphic trapping occupies the largest proportion of the theoretical storage capacity, followed by the solubility trapping and the residual trapping, and the mineral trapping takes the lowest proportion. The engineering storage capacity and the economic storage capacity are significantly lower than the theoretical storage capacity when considering the constrains of injectivity, security and economy, respectively accounting for 21.0% and 17.6% of the latter.

Some Indicators of the Water Regime in Some Varieties Belonging to the Monarda didyma L. Genus in the Conditions of Tashkent (Uzbekistan)

In this article, the names of 3 varieties of Monarda didyma L., which are considered to be introduced species, some indicators of the water regime in the climatic conditions of Uzbekistan: the amount of water in the leaves, water deficit, water storage capacity were studied in spring and summer, and seasonal changes were determined. According to these indicators of the water regime, the studied varieties belong to the labile water regime, high green mass (centner), seed yield (how many grams), resistance to diseases and pests have been determined, which shows that it is promising for introduction in the conditions of our republic. Therefore, it is recommended to breed these varieties in the foothills and hilly regions of Uzbekistan, where the amount of precipitation is more than 400 - 500 mm.

Research on energy storage capacity configuration for PV power plants using uncertainty analysis and its applications

Compensating for photovoltaic(PV)power forecast errors is an important function of energy storage systems.As PV power outputs have strong random fluctuations and uncertainty,it is difficult to satisfy the grid-connection requirements using fixed energy storage capacity configuration methods.In this paper,a method of configuring energy storage capacity is proposed based on the uncertainty of PV power generation.A k-means clustering algorithm is used to classify weather types based on differences in solar irradiance.The power forecast errors in different weather types are analyzed,and an energy storage system is used to compensate for the errors.The kernel density estimation is used to fit the distributions of the daily maximum power and maximum capacity requirements of the energy storage system;the power and capacity of the energy storage unit are calculated at different confidence levels.The optimized energy storage configuration of a PV plant is presented according to the calculated degrees of power and capacity satisfaction.The proposed method was validated using actual operating data from a PV power station.The results indicated that the required energy storage can be significantly reduced while compensating for power forecast errors.

Intensification of methane and hydrogen storage inclathrate hydrate and future prospect

Gas hydrate is a new technology for energy gas（methane/hydrogen）storage due to its large capacity of gas storage and safe.But industrial application of hydrate storage process was hindered by someproblems.For methane,the main problems are low formation rateand storage capacity,which can be solved by strengthening mass andheat transfer,such as adding additives,stirring,bubbling,etc.Onekind of additives can change the equilibrium curve to reduce the formation pressure of methane hydrate,and the other kind of additivesis surfactant,which can form micelle with water and increase the interface of water-gas.Dry water has the similar effects on the methanehydrate as surfactant.Additionally,stirring,bubbling,and sprayingcan increase formation rate and storage capacity due to mass transferstrengthened.Inserting internal or external heat exchange also canimprove formation rate because of good heat transfer.For hydrogen,the main difficulties are very high pressure for hydrate formed.Tetrahydrofuran（THF）,tetrabutylammonium bromide（TBAB） andtetrabutylammonium fluoride（TBAF） have been proved to be able todecrease the hydrogen hydrate formation pressure significantly.

Oxygen Storage Capacity of Pt-, Pd-, Rh/CeO_2-Based Oxide Catalyst

CZO （CeO2-ZrO2） and CZYO （CeO2-ZrO2-Y2O3） series of mixed oxides were prepared by coprecipitaion, and a part of these oxides were loaded with precious metals （PM）. XRD, BET, and oxygen storage capacity （OSC） investigations were performed on samples aged at 750, 900, and 1050 ℃. It was observed that BET surface area and OSC showed a marked decrease in CeO2 aged at high temperature, and the erystallite size showed an obvious increase. The CZO samples consist of cubic- and tetragonal crvstal phases, and their crystallite size increase rapidly when aged at high temperature. The CZYO samples consist of single crystal phase when the content of Y exceeds 0.15 mol, and their erystallite size increases slowly during high-temperature aging. It is concluded that additive Y can stabilize the performance of CZYO oxides. In the aged CZO and CZYO mixed-oxide systems, addition of a small amount of precious metals （Pt, Pd, Rh） increased the rate of reduction and led to an obvious improvement in OSC. OSC of CZO and CZYO with precious metals are related to their composition and the type of precious metal.

Hierarchical platinum–iridium neural electrodes structured by femtosecond laser for superwicking interface and superior charge storage capacity

The interfacial performance of implanted neural electrodes is crucial for stimulation safety and the recording quality of neuronal activity.This paper proposes a novel surface architecture and optimization strategy for the platinum–iridium(Pt–Ir)electrode to optimize electrochemical performance and wettability.A series of surface micro/nano structures were fabricated on Pt–Ir electrodes with different combinations of four adjustable laser-processing parameters.Subsequently,the electrodes were characterized by scanning electron microscopy,energy-dispersive X-ray spectroscopy,cyclic voltammetry,electrochemical impedance spectroscopy,and wetting behavior.The results show that electrode performance strongly depends on the surface morphology.Increasing scanning overlap along with moderate pulse energy and the right number of pulses leads to enriched surface micro/nano structures and improved electrode performance.It raises the maximum charge storage capacity to 128.2 mC/cm^(2) and the interface capacitance of electrodes to 3.0×10^(4)μF/cm^(2) for the geometric area,compared with 4.6 mC/cm^(2) and 443.1μF/cm2,respectively,for the smooth Pt–Ir electrode.The corresponding optimal results for the optically measured area are 111.8 mC/cm^(2) and 2.6×10^(4)μF/cm^(2),which indicate the contribution of fner structures to the ablation profle.The hierarchical structures formed by the femtosecond laser dramatically enhanced the wettability of the electrode interface,giving it superwicking properties.A wicking speed of approximately 80 mm/s was reached.Our optimization strategy,leading to superior performance of the superwicking Pt–Ir interface,is promising for use in new neural electrodes.

Heteroatom Doped Multi-Layered Graphene Material for Hydrogen Storage Application

A variety of distinctive techniques have been developed to produce graphene sheets and their functionalized subsidiaries or composites. The production of graphene sheets by oxidative exfoliation of graphite can be a suitable route for the preparation of high volumes of graphene derivatives. P-substituted graphene material is developed for its application in hydrogen sorption in room temperature. Phosphorous doped graphene material with multi-layers of graphene shows a nearly ~2.2 wt% hydrogen sorption capacity at 298 K and 100 bar. This value is higher than that for reduced graphene oxide (RGO without phosphorous).

Oxygen Storage Capacity and Adsorptive Property of Praseodymium Oxides

Oxygen storage and adsorptive properties of praseodymium oxides were investigated by pulse experiments and temperature - programmed desportion/reduction (TPD/TPR) experiments. Pr2O3 possesses the similar oxygen storage properties to CeO2, and its dynamic oxygen storage capacity is 14.9 mumol.g(-1). The studies on TPD Of O-2, H2O and CO and TPR show that Pr2O3 provides more active surface oxygen species and at a lower temperature than CeO2. It is suggested that Pr2O3 can be a well candidate as an oxygen storage component in automobile three-way catalyst.

Role of Surface Adsorption in Fast Oxygen Storage/Release of CeO_2-ZrO_2 Mixed Oxides

Four kinds of CeO2-ZrO2 mixed oxides, i.e., a physical mixture of ceria and zirconia （CZP）, zirconia-coated ceria （ZCC）, ceria-coated zirconia （CCZ） and a chemical mixture of celia and zirconia （CZC）, were prepared. The oxygen storage capacity （OSC） measurements at 500℃ were performed under transient and stationary reaction conditions. All the curves of CO2 evolution during CO-O2 cycles presented a bimodal shape. The fast peak was primarily the result of the reaction of CO with the oxygen from the oxides, which was mainly determined by the nature of the material The sec- ond peak was mostly related to the CO2 adsorption behavior and was highly influenced by the surface area and the number of surface active sites. As a result, OSC activity of the samples followed in the order of CZC 〉 CCZ 〉 ZCC=CZP.

Dynamic Oxygen Storage Capacity Measurements on Ceria-Based Material

Dynamic oxygen storage and release capability （OSC） measurement apparatus was designed to evaluate the OSC performance of ceria-based oxygen storage material. The optimum measurement condition was at a frequency of 0.1 Hz with the inlet gas-flow sequence CO （5S）→O2（5S）→CO→O2 and a flow rate of 300 ml·min^-1. Under this condition, similar regular square wave in the inlet and outlet of the reactor was obtained to guarantee the reliability of the dynamic OSC results. The dynamic OSC performance of the CeO2 and Ce0.67Zr0.33O2 mixed oxide prepared using the citric sol-gel method was studied at the optimum measurement condition with focus on both quantitative and qualitative analyses, The results reveal distinctly that Ce0.67Zr0.33O2 had better dynamic OSC performance because of its higher oxygen migration rate than CeO2. Under dynamic conditions, two CO2 production peaks occurred corresponding to the CO pulse and the O2 pulse, respectively, during the entire cycle. The intensity and ratio between the two CO2 productions were highly influenced by temperature and frequency indicating complex surface phenomena during the oxygen storage/release process, As a result, this set-up can be applied to the evaluation of ceria-based material on the OSC performance.

Application of spatially varying storage capacity model for runoff parameterization in semi-arid catchment

This paper introduces the method of designation of water storage capacity for each grid cell within a catchment, which considers topography, vegetation and soil synthetically. For the purpose of hydrological process simulation in semi-arid regions, a spatially varying storage capacity （VSC） model was developed based on the spatial distribution of water storage capacity and the vertical hybrid runoff mechanism. To verify the applicability of the VSC model, both the VSC model and a hybrid runoff model were used to simulate daily runoff processes in the catchment upstream of the Dianzi hydrological station from 1973 to 1979. The results showed that the annual average Nash-Sutcliffe coefficient was 0.80 for the VSC model, and only 0.67 for the hybrid runoff model. The higher annual average Nash-Sutcliffe coefficient of the VSC model means that this hydrological model can better simulate daily runoff processes in semi-arid regions. Furthermore, as a distributed hydrological model, the VSC model can be applied in regional water resource management.

Effect of VFe addition on hydrogen storage behavior of TiMn_(1.5)-based alloys

The hydrogen absorption and desorption behavior of TiMn_(1.25)Cr_(0.25)alloys with VFe substitution for partial Mn was investigated at 273, 293 and 313 K. It is found thatVFe substitution increases their hydrogen storage capacity, decreases the plateau pressure and thehysteresis factor of their pressure-composition-temperature (PCT) curves. After annealing treatmentat 1223 K for 6 h, TiMn_(0.95)Cr_(0.25)(VFe)_(0.3) alloy exhibits a lower hydrogen desorptionplateau pressure (0.27 MPa at 313 K) and a smaller hysteresis factor (0.13 at 313 K); the maximumand effective hydrogen storage capacities (mass fraction) are 2.03% and 1.12% respectively, whichcan satisfy the demand of hydrogen storage tanks for proton exchange membrane fuel cells (PEMFC).

Research on VSG Frequency Characteristics and Energy Storage Device Capacity and Charge-Discharge Characteristics Based on Feedforward Branch

Renewable energy is connected to the grid through the inverter,which in turn reduces the inertia and stability of the power grid itself.The traditional grid-connected inverter does not have the function of voltage regulation and frequency regulation and can therefore no longer adapt to the new development.The virtual synchronous generator(VSG)has the function of voltage regulation and frequency regulation,which has more prominent advantages than traditional inverters.Based on the principle of VSG,the relationship between the frequency characteristics and the energy storage capacity of the feedforward branch-based virtual synchronous machine(FVSG)is derived when the input power and grid frequency change.Reveal the relationship between the virtual inertia coefficient,damping coefficient,and frequency characteristics of VSG and energy storage capacity.An energy storage configuration method that meets the requirements of frequency variation characteristics is proposed.A mathematical model is established,and the Matlab/Simulink simulation software is used for modeling.The simulation results verify the relationship between the inertia coefficient,damping coefficient,and energy storage demand of the FVSG.

Impact of the Three Gorges Dam on Regulation and Storage Capacity of Poyang Lake

The regulation and storage capacity of Poyang Lake is infl uenced by the fl ow from the main stream of the Yangtze River and the fi ve rivers in the Poyang Lake basin.After the operation of the Three Gorges Dam(TGD),hydrological changes in the main stream of the Yangtze River impact water exchange between the Yangtze River and Poyang Lake.Based on the analysis of measured data and factors infl uencing outfl ow at Hukou station,a new empirical formula describing outfl ow at Hukou station and critical water level for lake storage capacity is established.The change in monthly storage capacity of Poyang Lake before and after the construction of the TGD is analyzed quantitatively.The results show that the fl ows from the main stream of the Yangtze River and the fi ve rivers in the Poyang Lake basin affect outfl ow and water storage capacity by changing the water level difference between Xingzi and Hukou stations and by changing the water level at Hukou station.But the Yangtze River and the fi ve rivers in the Poyang Lake basin differ in process and degree.If the water level at Hukou station remains consistent,when the fl ow from the fi ver rivers increases by 1,000 m3/s,the outfl ow at Hukou station increases by 304 m3/s.When the fl ow from the main stream of the Yangtze River increases by 1,000 m3/s,the outfl ow at Hukou station decreases by 724 m3/s.In addition,the operation of the TGD affects the water storage capacity of Poyang Lake.The water volume of Poyang Lake decreases by 49.4%in September,but increases by 47.7%in May.

Canopy Storage Implications on Interception Loss Modeling

A rainfall interception methodology was implemented in a deciduous Ficus benjamina (L.) tree to evaluate the interception loss, as well as the dynamics on canopy storage capacity (S) and free through fall (ρ). Measurements of gross precipitation (Pg), through fall and meteorological data were recorded every 5 minutes. Nineteen individual storms from summer to autumn 2005, and twenty one in spring to autumn, 2006 were analyzed. For the studied period, 151.59 mm and 203.35 mm of rainfall occurred on 2005 and 2006 respectively. Canopy interception was 59.46% and 70.98% of Pg for the first and second year. Throughfall data recorded during 2005 were ?38.14% (of Pg) and 27.21% (of Pg) for 2006. The throughfall and gross precipitation relationship yielded S = 1.50 mm for the 2005 data. In 2006 storms were analyzed in detail, where ρ and S varied in a range from 0.10 to 0.64 and from 1.00 to 2.03 mm, respectively. Moreover, application of the Rutter and Gash models with two years of rainfall data (2005-2006) from the study area indicated an underestimation and overestimation of 69% and 88%, respectively. The slightly best prediction of the interception loss was obtained with the Gash model. Yet S and ρ change significantly due to wind speed, temperature, rainfall intensity and seasonal vegetation development.

Optimizing groundwater recharge plan in North China Plain to repair shallow groundwater depression zone, China

The North China Plain is one of the main grain producing areas in China. However, overexploitation has long been unsustainable since the water supply is mainly from groundwater. Since 2014,the South-to-North Water Diversion Project's central route has been charted to the integrated management of water supply and over-exploitation, which has alleviated the problem to a certain extent. Although the Ministry of Water Resources has made many efforts on groundwater recharge since 2018 most of which have been successful, the recharge has not yet been sufficiently focused on the repair of shallow groundwater depression zones. It still needs further optimization. This paper discusses this particular issue,proposes optimized recharge plan and provides the following recommendations:(1) Seven priority target areas are selected for groundwater recharge in alluvial and proluvial fans in the piedmont plain, and the storage capacity is estimated to be 181.00×10~8 m~3;(2) A recharge of 31.18×10~8 m~3/a is required by 2035 to achieve the repair target;(3) It is proposed to increase the recharge of Hutuo River, Dasha River and Tanghe River to 19.00×10~8 m~3/a and to rehabilitate Gaoliqing-Ningbailong Depression Zone;increase the recharge of Fuyang River, Zhanghe River and Anyang River to 7.05×10~8 m~3/a and rehabilitate Handan Feixiang-Guangping Depression Zone;increase the recharge of Luanhe River by 0.56×10~8 m~3/a and restore Tanghai Depression Zone and Luanan-Leting Depression Zone;moderately reduce the amount of water recharged to North Canal and Yongding River to prevent excessive rebound of groundwater;(4) Recharge through well is implemented on a pilot basis in areas of severe urban ground subsidence and coastal saltwater intrusion;(5) An early warning mechanism for groundwater quality risks in recharge areas is established to ensure the safety. The numerical groundwater flow model also proves reasonable groundwater level restoration in the depression zones by 2035.