DISTRIBUTED MICROBEND FIBER-OPTIC STRAIN SENSOR

The distributed strain sensor has significant application in real time measurement of strain status for large and important engineering structures such as aircraft, bridge and dam. In this paper, a quasi distributed optical fiber strain sensor system is set up using optical time domain reflect technique. The local strain sensors based on a novel microbend configuration are designed and applied to measure local strains along the optical fiber. As the result of the experimental research, the microbend sensors show high sensitivity, good linearity and repeatability in certain operation range.

Stress and strain analysis on the anastomosis site sutured with either epineurial or perineurial sutures after simulation of sciatic nerve injury

The magnitude of tensile stress and tensile strain at an anastomosis site under physiological stress is an important factor for the success of anastomosis following suturing in peripheral nerve injury treatment. Sciatic nerves from fresh adult cadavers were used to create models of sciatic nerve injury. The denervated specimens underwent epineurial and perineurial suturing. The elastic modulus （40.96 ＋ 2.59 MPa） and Poisson ratio （0.37 ＋ 0.02） of the normal sciatic nerve were measured by strain electrical measurement. A resistance strain gauge was pasted on the front, back left, and right of the edge of the anastomosis site after suturing. Strain electrical measurement results showed that the stress and strain values of the sciatic nerve following perineurial suturing were lower than those following epineurial suturing. Scanning electron microscopy revealed that the sciatic nerve fibers were disordered following epineurial compared with perineurial suturing. These results indicate that the effect of perineurial suturing in sciatic nerve injury repair is better than that of epineurial suturing.

Wireless Strain Measurement Based on a Microstrip Patch Antenna

Wireless interrogation of a rectangular microstrip patch antenna for strain measurement is investigated by simulations.To analyze the antenna performance,a microstrip line-feeding patch antenna at 10 GHz is designed.A patch antenna wirelessly fed by a horn is proposed to measure the strain.The direction information of strain detected by the patch antenna is also considered.The strain can be detected both in the width and length directions.It is shown that the strain can be measured wirelessly using a standard horn antenna.This kind of wireless strain-sensing technique offers significant potential for wireless structural health monitoring(SHM),especially for high-end equipment.

Carrier fringe method of moire interferometry for tiny strain measurements in micro-field

In this paper, we demonstrate a new optical method for tiny strain measurements based on the principle of carrier fringes of moire interferometry. A cross-line grating with frequency of 1200 lp/mm is replicated on the specimen surface, and the strain can be deduced from the changes in carrier fringes before and after the deformation of an object. Four coherent laser beams are used to obtain the carrier fringe patterns of field U and V. Both theoretical analysis and numerical simulation indicate that the ideal accuracy of strain can be controlled within a range of ±1με. Case study of a plane extension experiment shows that the measurement accuracy of strain can be controlled within the range of ±10με. The average strain values of every row of field U and every column of field V can be obtained by using this method, and approximated strain of every pixel in the whole-field can be further acquired, and thus it is possible to measure tiny strains occurred in a micro-field. The technology in this paper can provide comprehensive information for analyzing related mechanical content in the field of MEMS.

Hydraulic bulging process with axial feedings and strain field of U-shaped metal bellows

Based on the traditional hydraulic bulging process,an improved hydraulic bulging process with axial feeding in the bulging process was proposed.The finite element simulation and experiment of bellows formed by the traditional and improved hydraulic bulging processes were conducted.The grid strain measurement system analysis results of strain and wall thickness distribution of the metal bellows,obtained from simulation and experiment,show that the maximum thinning rates of the wall thickness under the traditional and improved processes were 15%and 10%,respectively.And the wall thickness distribution of the metal bellows formed with improved process was more uniform.The strain values from the root to crown of the waveform increased gradually.However,the strain values were smaller than those of traditional process due to the axial feeding of the improved process in bulging process.

Strain Measurement on the Toroidal Field (TF) Coil Cases

The stress-strain state of the structure is a matter of interest to designer. The strain measurement of superconducting magnets at cryogenic temperature is a specific technique. Based on strain measurement of TF coil case for EAST, this paper presents a measuring technique at cryogenic temperature and on intense magnetic field. The compensation methods for both temperature and magnetic field effects of the gauges, together with the measured results are involved, and the discussions of the measured results are given in the paper.

Strain data recorded in Xinjiang and their bearing on Tianshan’s uplift/shortening and Tarim basin’s rotation

Based on the continuous strain data recorded in Xinjiang since 1985, we discuss the mechanisms of Tianshan＇ s uplift and Tarim basin＇ s clockwise rotation. The results indicate ： 1 ） The principal - compression directions in Tianshan are nearly NS, and their intersection angles with regional structures and mountains are nearly perpendicular, which is in accordance with Tianshan＇ s uplift and crustal shortening. 2）The principal compressions around Tarim basin tend to facilitate the regional faults＇ left-lateral strike-slip movements and the basin＇ s clockwise rotation. These phenomena of uplift/shortening and rotation are fundamentally the re- suits of India plate＇ s northward push on Euro-Asia plate, and the associated Pamir arc ＇ s rapid northward movement and regional blocks＇ interaction.

In-situ strain measurement and error analysis of arc welding with 2D digital image correlation

The deformation and residual stress generated by the welding process can seriously affect the use of components.As a result,it is very important to understand the evolution of stress and strain during the welding process.The strain measurement method based on digital image correlation(DIC)is an excellent method to detect welding strain and residual stress.The out-of-plane translation and out-of-plane rotation introduce errors to the two-dimensional DIC.In this paper,the causes of errors are analyzed theoretically,and the formulas of errors caused by the out-of-plane displacement and the out-of-plane rotation are derived.The out-of-plane translation experiment and the out-of-plane rotation experiment were carried out to verify the theory,and the experimental results are consistent with the theoretical analysis results.The error caused by the out-of-plane translation can be reduced by increasing the object distance;the error caused by the out-of-plane rotation is greatly affected by the rotation angle.

Strain Measurement for Hollow Projectiles During Its Penetration of Concrete Targets

Gives a new technique to measure the dynamic deformation behavior and strain development of a hollow steel projectile during its penetration of concrete targets. Direct strain measurement was performed by applying strain gages attached to the inner walls of the hollow projectile, linked with on-board testing and storage recorder. This on-board test-record system is easy to operate, cost-effective and can provide reasonable, accurate and detailed information. Obverse ballistic experiments were carried out on ogival-nose hollow projectiles normally impacting concrete targets at velocities from 150 m/s to 300 m/s. The deformation process of projectiles was measured, recorded and played back. Profiles of voltage-time relationship were successively obtained and transfered to strain-time relationship with the aid of calibration tables. It was found that projectiles go through a series of compression and tension deformations intermittently. Relationships between strain development and projectile deformation process were discussed.

STRAIN MEASUREMENT IN THE SMART COMPOSITE

The smart composite structure is a new type of structure developed in recent years. It can be used in aircraft or some other important devices. The smart composite structure in which some sensors, actuators and other components are embedded can perform the tasks such damage evaluation, strain measurement, changing stress and suppressing vibration by itself. In the Performance of the tasks above, many parameters must be measured, among which the measurement of strain field is very important. In this paper, some distributed and quasi-distributed embedding optic fiber strain sensors are introduced, and their specialities are discussed.

DETERMINATION OF INTERNAL STRAIN IN 3-D BRAIDED COMPOSITES USING OPTIC FIBER STRAIN SENSORS

A reliable understanding of the properties of 3-D braided composites is of primary importance for proper utilization of these materials. A new method is introduced to study the mechanical performance of braided composite materials using embedded optic fiber sensors. Experimental research is performed to devise a method of incorporating optic fibers into a 3-D braided composite structure. The efficacy of this new testing method is evaluated on two counts. First, the optical performance of optic fibers is studied before and after incorporated into 3-D braided composites, as well as after completion of the manufacturing process for 3-D braided composites, to validate the ability of the optic fiber to survive the manufacturing process. On the other hand, the influence of incorporated optic fiber on the original braided composite is also researched by tension and compression experiments. Second, two kinds of optic fiber sensors are co-embedded into 3-D braided composites to evaluate their respective ability to measure the internal strain. Experimental results show that multiple optic fiber sensors can be co-braided into 3-D braided composites to determine their internal strain which is difficult to be fulfilled by other current existing methods.

APPLICATION OF GRATING DIFFRACTION IN STRAIN MEASUREMENT

In this paper a new technique for measuring strain is presented. Using grating as the strain sensor, we can obtain strain and stress components by measuring the deformation of the space position of diffraction spots. The cost of the holographic grating by embossing is much reduced. By using the video and computer techniques the strain and stress values can be obtained automatically.

Instantaneous Creep in Face-centered Cubic Metals at Ultra- low Strain Rates by a High-resolution Strain Measurement

Instantaneous creep in face-centered cubic metals, 5N Al（99.999%）, 2N Al （99%） and 4N Cu （99.99%） with different grain sizes, was firstly investigated by sudden stress-change experiments at ultra- low strain rates ε ≤10-10 s-1 and temperature T 〈 0.32 Tn. The experimental results indicate that the observed instantaneous creep is strongly dependent on grain size, the concentration of impurity, and stacking fault energy. Creep in high-purity aluminum, 5N Al, with a very large grain size, d 〉 1600μm, shows non-viscous behavior, and is controlled by the recovery of dislocations in the boundary of dislocation cells. On the other hand, for 5N A1 with a small grain size, d=30μm, and low-purity aluminum, 2N A1, with d8= 25μm, creep shows viscous behavior and may be related to ＇low temperature grain boundary sliding＇. For high-purity copper, 4N Cu, with d= 40 grn and lower stacking fault energy, creep shows a non-viscous behavior, and is controlled by the recovery process of dislocations. For all of the samples, creep shows anelastic behavior.

LASER SPECTRAL ANALYSIS OF STRAIN MEASUREMNT

Modern opticai theory has shown that the far field or Fraunbofer diffraction equipment is identical to the Fourier spectral analyzer. In the Fourier speetral analyzer the Fourier spectra or the Fraunhofer diffaction pattern of a graph is formed on the back focal plane when a laser beam is directed on the graph lying on the front foeal plane ; the Fourier spectra of the graph is also subjected to change during the deformation of the graph. Through analyzing the change of Fourier spectra the deformation of the graph can be obtained. A few years ago,based on the above principles the authors proposed a new technique of strain measurement by laser spectral analysis. Demonstration and discussion will be made in detail in this paper.

Fiber optic sensing and performance evaluation of a water conveyance tunnel with composite linings under super-high internal pressures

For long-distance water conveyance shield tunnels in operation,the high internal water pressure may cause excessive deformation of composite linings,affecting their structural integrity and serviceability.However,the deformation and failure characteristics of lining structures under internal water pressure are not well investigated in the literature,particularly for three-layer composite linings.This study presents an in situ experimental investigation on the response of two types of composite linings(i.e.separated and combined lining structures)subjected to internal pressures,in which a fiber optic nerve system(FONS)equipped with distributed strain and displacement sensing nerves was employed to monitor the performance of the two composite linings during testing.The experimental results clearly show that the damage of the tunnel lining under different internal pressures was mainly located in the self-compaction concrete layer.The separated lining structure responded more aggressively to the variations in internal pressures than the combined one.Moreover,two evaluation indices,i.e.radial displacement and effective stiffness coefficient,are proposed for describing the changes in the structural bearing performance.The effective stiffness coefficients of the two types of lining structures were reduced by 39.4%and 29.5%,respectively.Considering the convenience of field monitoring,it is suggested that the average strains at different layers can be used as characteristic parameters for estimating the health conditions of lining structures in service.The analysis results provide a practical reference for the design and health evaluation of water conveyance shield tunnels with composite linings.

In-site health monitoring of cement concrete pavements based on optical fiber sensing technology

Premature stress of cement concrete pavements i the coupled action of construction technique,structural ma-terial and environmental action.It is quite diffiault to accurately get the actual stress distribution merely based on the theoretical or simulation analysis.Ther efore,in-situ health monitoring is particularly si gnificant to obtain the stress or strain information for the assessment on structural perfor mance of cement concrete pavements.To contribute this topic,different kinds of FBG based sensors have been specially designed to measure the tem-perature,pressure and deformation in cement concrete pavements.A relatively long-term monitoring has been aonducted to collect the effective data after the solidification of the pavement lasts for about 15 d.Data analysis indicates that the temperature variation inside the pavement was very stable,with maximum ampltude smaller than 2.25°C in Sep.2020.The longitudinal,transverse and ver tical deformations of the pavement behaved in non-umniform distribution,and partial me asuring points suffered from large tensile force.The concrete course had better deformation resi stance than that of the soil base,and local interfacial micro void defects existed in the soil base.The preliminary results can help to understand the actual structural performance of cement concrete pavements based on the optical fiber sensing sys tem.

Revealing sodium storage mechanism of hard carbon anodes through in-situ investigation of mechano-electrochemical coupling behavior

Hard carbon(HC)is considered a promising anode material for sodium-ion batteries due to its relatively low price and high specific capacity.However,HC still suffers from unclear reaction mechanisms and unsatisfactory cycling stability.The study of mechano-electrochemical coupling behavior by in-situ measurement techniques is expected to understand the sodium storage and degradation mechanisms.In this paper,the strain and stress evolution of HC anodes at different sodiation/desodiation depths and cycles are investigated by combining electrochemical methods,digital image correlation,and theoretical equations.The observation by monitoring the in-situ strain evolution during the redox process supports the“adsorption-intercalation/filling”mechanism in reduction and the“de-filling/de-intercalation-deso rption”mechanism in oxidation.Further studies have demonstrated that the strain and stress of the electrode show periodic changes accompanied by a continuous accumulation of residual stress during cycles,explaining the capacity degradation mechanism of HC from a mechanical perspective.In addition,when the higher current density is applied,the electrodes experience greater strain and stress associated with the Na+insertion rate.This work clarifies the Na-storage mechanism and the mechano-electrochemical coupling mechanism of HC anodes by in-situ strain measurement,which helps optimize and design the anode materials of sodium-ion batteries from the perspective of interface microstructure and multi-field coupling,such as in situ integrated interface structure design.

DEVELOPMENT OF EXTRINSIC FABRY PEROT FIBER SENSOR AND ITS APPLICATION TO SMART MATERIALS

In the work of developing extrinsic fabry perot interferometric (EFPI), the key technology of polishing fiber optic endfaces and coating the multilayer of dielectric films on them is raised and resolved to settle the disturbance and stability problem of EFPI, which simplifies the sensing system, improves the sensor performance and reduces the cost. In this paper, the relations between the output interferential light intensity and the F P cavity length are calculated based on the theory of mode field coupling. The EFPI fiber optic sensor is adhered to a distributed smart laminate beam to detect vibration frequency and axial strain value, the results coincident with the results tested by PZT.

Review of Electronic Speckle Pattern Interferometry(ESPI) for Three Dimensional Displacement Measurement

Three dimensional（3D） displacements, which can be translated further into 3D strain, are key parameters tor design, manufacturing and quality control. Using different optical setups, phase-shift methods, and algorithms, several different 3D electronic speckle pattern interferometry（ESPl） systems for displacement and strain measurements have been achieved and commercialized. This paper provides a review of the recent developments in ESPI systems for 3D displacement and strain measurement. After an overview of the fundamentals of ESP! theory, temporal phase-shift, and spatial phase-shift techniques, 3D deformation measurements by the temporal phase-shift ESPI system, which is suited well for static measurement, and by the spatial phase-shift ESPI system, which is particularly useful for dynamic measurement, are discussed. For each method, the basic theory, a brief derivation and different optical layouts are presented. The state of art application, potential and limitation of the ESPI systems are shown and demonstrated.

Effect of asymmetric rolling under high friction coefficient on recrystallization texture and plastic anisotropy of AA1050 alloy

In asymmetric rolling(ASR) the circumferential velocities of the working rolls are different. This yields a complex deformation mode with shear, compression and rigid body rotation components. The main microstructural modification is on crystallographic texture, and, for aluminium alloys, this may improve the deformability after recrystallization. This work correlated the process variables, thickness reduction per pass(TRP) and velocity ratio between the upper and bottom rolls, with the texture development and the plastic properties after annealing. Finite element(FE) simulations were performed to quantify the influence of the strain components. Experimental data on texture, and plastic anisotropy were analyzed. In the sheet centre a crystallographic rotation of the compression components about the TD(transverse direction) axis was obtained, which yielded the development of {111}//ND(normal direction) texture components. On the surfaces the local variation of the velocity gradients caused an extra rotation component about ND. This yielded the increment of rotated cube components. After annealing the main texture components at the sheet centre were maintained and the texture intensity decreased. The planar anisotropy(△r) was reduced but the normal anisotropy and deep drawability obtained by the Erichsen test were similar for all conditions. The most favourable reduction of △r was obtained at a velocity ratio of 1.5 and TRP of 10%.