General displacement arch-cantilever element method for stress analysis of arch dam

Based on the general displacement method and the basic hypothesis of the trial load method, a new advanced trial load method, the general displacement arch-cantilever element method, was proposed to derive the transformation relation of displacements and loads between the surface nodes and middle plane nodes. This method considers the nodes on upstream and downstream surfaces of the arch dam to be exit nodes （master nodes）, and the middle plane nodes to be slave nodes. According to the derived displacement and load transformation matrices, the equilibrium equation treating the displacement of middle plane nodes as a basic unknown variable is transformed into one that treats the displacement of upstream and downstream nodes as a basic unknown variable. Because the surface nodes have only three degrees of freedom （DOF）, this method can be directly coupled with the finite element method （FEM）, which is used for foundation simulation to analyze the stress of the arch dam with consideration of dam-foundation interaction. Moreover, using the FEM, the nodal load of the arch dam can be easily obtained. Case studies of a typical cylindrical arch dam and the Wudongde arch dam demonstrate the robustness and feasibility of the proposed method.

Analysis of the Wenchuan Ms8.0 Earthquake's Co-seismic Stress and Displacement Change by Using the Finite Element Method

The variation of in situ stress before and after earthquakes is an issue studied by geologists. In this paper, on the basis of the fault slip dislocation model of Wenchuan Ms8.0 earthquake, the changes of co-seismic displacement and the distribution functions of stress tensor around the Longmen Shan fault zone are calculated. The results show that the co-seismic maximum surface displacement is 4.9 m in the horizontal direction and 6.5 m in the vertical direction, which is almost consistent with the on-site survey and GPS observations. The co-seismic maximum horizontal stress in the hanging wall and footwall decreased sharply as the distance from the Longmen Shan fault zone increased. However, the vertical stress and minimum horizontal stress increased in the footwall and in some areas of the hanging wall. The study of the co-seismic displacement and stress was mainly focused on the long and narrow region along the Longmen Shan fault zone, which coincides with the distribution of the earthquake aftershocks. Therefore, the co-seismic stress only affects the aftershocks, and does not affect distant faults and seismic activities. The results are almost consistent with in situ stress measurements at the two sites before and after Wenchuan Ms8.0 earthquake. Along the fault plane, the co-seismic shear stress in the dip direction is larger than that in the strike direction, which indicates that the faulting mechanism of the Longmen Shan fault zone is a dominant thrust with minor strike-slipping. The results can be used as a reference value for future studies of earthquake mechanisms.

An extended displacement discontinuity method for analysis of stress wave propagation in viscoelastic rock mass

An extended displacement discontinuity method (EDDM) is proposed to analyze the stress wave propagation in jointed viscoelastic rock mass (VRM).The discontinuities in a rock mass are divided into two groups.The primary group with an average geometrical size larger than or in the same order of magnitude of wavelength of a concerned stress wave is defined as 'macro-joints',while the secondary group with a high density and relatively small geometrical size compared to the wavelength is known as 'micro-defects'.The rock mass with micro-defects is modeled as an equivalent viscoelastic medium while the macro-joints in the rock mass are modeled explicitly as physical discontinuities.Viscoelastic properties of a micro-defected sedimentary rock are obtained by longitudinally impacting a cored long sedimentary rod with a pendulum.Wave propagation coefficient and dynamic viscoelastic modulus are measured.The EDDM is then successfully employed to analyze the wave propagation across macro-joint in VRM.The effect of the rock viscosity on the stress wave propagation is evaluated by comparing the results of VRM from the presented EDDM with those of an elastic rock mass (ERM) from the conventional displacement discontinuity method (CDDM).The CDDM is a special case of the EDDM under the condition that the rock viscosity is ignored.Comparison of the reflected and transmitted waves shows that the essential rock viscosity has a significant effect on stress wave attenuation.When a short propagation distance of a stress wave is considered,the results obtained from the CDDM approximate to the EDDM solutions,however,when the propagation distance is sufficiently long relative to the wavelength,the effect of rock viscosity on the stress wave propagation cannot be ignored.

Numerical analysis of loaded stress and central displacement of deep groove ball bearing

The aim of this work is to develop a three-dimensional model of deep groove ball bearing to investigate the loaded stresses and central displacements of bearing rings. The equivalent stresses and central displacements of bearing rings are obtained based on the simulated analysis. Moreover, several parameters, such as load magnitude, raceway groove curvature radius(RGCR), thicknesses of outer and inner rings, are varied to investigate their effects on the equivalent stresses and central displacements of bearing rings. Research results provide useful guidelines for determining the design parameters.

Displacement-based back analysis of mitigating the effects of displacement loss in underground engineering

Displacement-monitoring-based back analysis is a popular method for geomechanical parameter estimation.However,due to the delayed installation of multi-point extensometers,the monitoring curve is only a part of the overall one,leading to displacement loss.Besides,the monitoring and construction time on the monitoring curve is difficult to determine.In the literature,the final displacement was selected for the back analysis,which could induce unreliable results.In this paper,a displacement-based back analysis method to mitigate the influence of displacement loss is developed.A robust hybrid optimization algorithm is proposed as a substitute for time-consuming numerical simulation.It integrates the strengths of the nonlinear mapping and prediction capability of the support vector machine(SVM)algorithm,the global searching and optimization characteristics of the optimized particle swarm optimization(OPSO)algorithm,and the nonlinear numerical simulation capability of ABAQUS.To avoid being trapped in the local optimum and to improve the efficiency of optimization,the standard PSO algorithm is improved and is compared with other three algorithms(genetic algorithm(GA),simulated annealing(SA),and standard PSO).The results indicate the superiority of OPSO algorithm.Finally,the hybrid optimization algorithm is applied to an engineering project.The back-analyzed parameters are submitted to numerical analysis,and comparison between the calculated and monitoring displacement curve shows that this hybrid algorithm can offer a reasonable reference for geomechanical parameters estimation.

Generalized response displacement methods for seismic analysis of underground structures with complex cross section

The response displacement method(RDM)is recommended for the seismic analysis of underground structures in the transverse direction for many codes,including bases for design of structures-seismic actions for designing geotechnical works(ISO 23469)and code for seismic design of urban rail transit structures(GB 50909-2014).However,there are some obvious limitations in the application of RDM.Springs and the shear stress of the soil could be approximately evaluated for the structures having a simple cross section,such as rectangular and circular structures.It is necessary to propose simplified seismic analysis methods for structures with complex cross sections.This paper refers to the idea of RDM and proposes three generalized response displacement methods(GRDM).In GRDM1,a part of the soil surrounding a structure is selected to generate a generalized underground structure with a rectangular cross section,and the same analysis model as RDM is applied to analyze the responses of the structure.In GRDM2,a hollow soil model without a generalized structure is used to compute the equivalent load caused by the relative displacement of the soil,and the soil-structure interaction model is applied to calculate the responses of the structure.In GRDM3,a continuous soil model is applied to compute the equivalent load caused by the relative displacement and shear stress of the soil,and the soil-structure interaction model is applied to analyze the responses of the structure,which is the same as the model used in GRDM2.The time-history analysis method(THAM)is used to evaluate the accuracy of the proposed simplified methods.Results show that the error of GRDM1 is about 20%,while the error is only 5%for GRDM2 and GRDM3.Among the three proposed methods,GRDM3 has obvious advantages regarding calculation efficiency and accuracy.Therefore,it is recommended to use GRDM3 for the seismic response analysis of underground structures that have conventional simple or complex cross sections.

Direct scaling of residual displacements for bilinear and pinching oscillators

The estimation of residual displacements in a structure due to an anticipated earthquake event has increasingly become an important component of performance-based earthquake engineering because controlling these displacements plays an important role in ensuring cost-feasible or cost-effective repairs in a damaged structure after the event.An attempt is made in this study to obtain statistical estimates of constant-ductility residual displacement spectra for bilinear and pinching oscillators with 5%initial damping,directly in terms of easily available seismological,site,and model parameters.None of the available models for the bilinear and pinching oscillators are useful when design spectra for a seismic hazard at a site are not available.The statistical estimates of a residual displacement spectrum are proposed in terms of earthquake magnitude,epicentral distance,site geology parameter,and three model parameters for a given set of ductility demand and a hysteretic energy capacity coefficient in the case of bilinear and pinching models,as well as for a given set of pinching parameters for displacement and strength at the breakpoint in the case of pinching model alone.The proposed scaling model is applicable to horizontal ground motions in the western U.S.for earthquake magnitudes less than 7 or epicentral distances greater than 20 km.

Reciprocal Association between Psychological Distress and PTSD and Their Relationship with Pre-Displacement Stressors among Displaced Women

It is established in the psychological literature that pre-displacement stressors,PTSD symptoms,and psycholo-gical distress are associated among internally displaced persons.However,existing studies have not demonstrated the mechanism underlying these associations.This study compared two explanatory models;one with PTSD symptoms severity explaining the indirect association between pre-displacement stressors and psychological dis-tress,and the other with psychological distress explaining the indirect relationship between pre-displacement stressors and PTSD symptoms severity.In a cross-sectional design,631 women(Mean age=31.18±8.59)were conveniently and purposely selected from the displaced women harboured in two camps in Borno State,Nigeria,due to the Boko-Haram insurgency.Data were collected utilizing structured questionnaires and subjected to path analyses.Results demonstrated that PTSD symptoms severity and psychological distress indirectly explained their respective and independent association with pre-displacement stressors.However,PTSD symptoms had a statis-tically larger standardized indirect effect size,greater indirect effect percentage,and bigger kappa-squared(k2)effect size than psychological distress.PTSD symptoms and psychological distress may have a reciprocal influence on each other from pre-displacement stressors.However,PTSD symptoms can better explain the association between pre-displacement stressors and psychological distress than the other way around.These outcomes have important implications for the psychological treatment of displaced persons.

DISPLACEMENT CONTROL AND KINETIC ANALYSIS OF A NOVEL VARIABLE DISPLACEMENT COMPRESSOR FOR AUTOMOTIVE AIR CONDITIONER

A novel variable displacement compressor (VDC) for automotive air conditioner (AAC) is introduced, which inherits the advantages of common wobble plate type VDC. It has fewer parts and makes less noise, and instead of pneumatic valve the displacement is controlled by electronic control valve. In order to know the control mechanism well and get a good control effect, a mathematical model for the variable displacement mechanism is developed according to the geometrical and kinematical information of the compressor. Using the model, the effect of relevant parameters on variable displace control is estimated. It is helpful to make the optimum decision in the flow control of AAC. As the novel displacement control device, the structure and control rule of electronic control valve is introduced. It can get better effect than the conventional pneumatic valves. And by using this new electronic control device, the optimum systemic control of AAC is available.

Effects of displacement boundary conditions on thermal deformation in thermal stress problems

Most computational structural engineers are paying more attention to applying loads rather than to DBCs （Displacement Boundary Conditions） because most static stable mechanical structures are working under already prescribed displacement boundary conditions. In all of the computational analysis of solving a system of algebraic equations, such as FEM （Finite Element Method）, three translational and three rotational degrees of freedom （DOF） should be constrained （by applying DBCs） before solving the system of algebraic equation in order to prevent rigid body motions of the analysis results （singular problem）. However, it is very difficult for an inexperienced engineer or designer to apply proper DBCs in the case of thermal stress analysis where no prescribed DBCs or constraints exist, for example in water quenching for heat treatment. Moreover, improper DBCs cause incorrect solutions in thermal stress analysis, such as stress concentration or unreasonable deformation phases. To avoid these problems, we studied a technique which performs the thermal stress analysis without any DBCs; and then removes rigid body motions from the deformation results in a post process step as the need arises. The proposed technique makes it easy to apply DBCs and prevent the error caused by improper DBCs. We proved it was mathematically possible to solve a system of algebraic equations without a step of applying DBCs. We also compared the analysis results with those of a traditional procedure for real castings.

Finite Element Analysis of In-Plane Displacements and Von-Mises Stresses in Ellipsoidal and Circular Cylinderical Petroleum Tankers

Road tankers are the most used means of transporting petroleum product to end users due to its cost effectiveness and energy-efficiency. The cylindrical tank has been well designed for by ASME VIII divisions 1 and 2 using analytical equations. Petrol tankers are not circular but elliptical probably for stability during transportation. This paper has used the finite element method to investigate in-plane displacements and Von-Mises stresses in both circular and elliptical cylindrical tanks under full loading. An elliptical OANDO? tanker of 66.78 m3volume and shell thickness of0.2 mmand an equivalent volume circular cylindrical tank was used for the simulation. MATLAB? was used to generate geometrical mesh model of the petroleum tankers, extract element coordinates and conduct the finite element analysis. Plane strain condition was used in analyzing a section of the petroleum tanker. It was observed that an equivalent volume circular cylindrical tank was under a higher internal pressure (16,858 N/m2) compared to the elliptical cylinder (14,480 N/m2). Von-Mises stress and in-plane displacements showed direct linear relationships with internal fluid pressure. Von-Mises stress in the elliptical tank was found to be lower (5.7 × 106 N/m2) than for the circular tank (8 × 106 N/m2). In plane displacements was zero in the longitudinal direction for both tanks and of the order of 10-4 mm in the y-direction for both tanks with the circular larger by about 2.5 × 10-3 cm. So in addition to tank stability on the lorry, the Von-Mises stresses were lower as well for the elliptical tank. It was also observed that Von-Mises stresses were far below the yield stress of the steel plate. However, the effect of weldment area on lowering of yield stress was not studied. Stress values were validated using analytical method and found to be insignificantly different (P > 0.05).

Nonlinear Static Finite Element Stress Analysis of Pipe-in-Pipe Risers

Owing to the complexity of the pipe-in-pipe (PIP) riser system in structure, load and restraint, many problems arise in the structural analysis of the system. This paper presents a new method for nonlinear static finite element stress analysis of the PIP riser system. The finite element (FE) model of the PIP riser system is built via software AutoPIPE 6.1. According to the specialties of a variety of components in the PIP riser system, different elements are used so as to model the system accurately. Allowing for the complication in modeling the effects of seabed restraint, a technique based on the bilinear spring concept is developed to calculate the soil properties. Then, based on a pipeline project, the entire procedure of stress analysis is discussed in detail, including creation of an FE model, processing of input data and analysis of results. A wide range of loading schemes is investigated to ascertain that the stresses remain within the acceptable range of the pipe material strength. Finally, the effects of the location of flanges, the thermal expansion of submarine pipelines and the seabed restraint on stress distribution in the riser and expansion loop are studied, which are valuable for pipeline designers.

Effect of stress sensitivity on displacement efficiency in CO_2 flooding for fractured low permeability reservoirs

Carbon dioxide flooding is an effective means of enhanced oil recovery for low permeability reservoirs. If fractures are present in the reservoir, CO2 may flow along the fractures, resulting in low gas displacement efficiency. Reservoir pore pressure will fluctuate to some extent during a CO2 flood, causing a change in effective confining pressure. The result is rock deformation and a reduction in permeability with the reduction in fracture permeability, causing increased flow resistance in the fracture space. Simultaneously, gas cross flowing along the fractures is partially restrained. In this work, the effect of stress changes on permeability was studied through a series of flow experiments. The change in the flowrate distribution in a matrix block and contained fracture with an increase in effective pressure were analyzed. The results lead to an implicit comparison which shows that permeability of fractured core decreases sharply with an increase in effective confining pressure. The fracture flowrate ratio declines and the matrix flowrate ratio increases. Fracture flow will partially divert to the matrix block with the increase in effective confining pressure, improving gas displacement efficiency.

Earthquake-induced landslide displacement attenuation models and application in probabilistic seismic landslide displacement analysis

A landslide displacement (DLL) attenuation model has been developed using spectral intensity and a ratio of critical acceleration coefficient to ground acceleration coefficient. In the development of the model,a New Zealand earthquake record data set with magnitudes ranging from 5.0 to 7.2 within a source distance of 175 km is used. The model can be used to carry out deterministic landslide displacement analysis,and readily extended to carry out probabilistic seismic landslide displacement analysis. DLL attenuation models have also been developed by using earthquake source terms,such as magnitude and source distance,that account for the effects of earthquake faulttype,source type,and site conditions. Sensitivity analyses show that the predicted DLL values from the new models are close to those from the Romeo model that was developed from an Italian earthquake record data set. The proposed models are also applied to an analysis of landslide displacements in the Wenchuan earthquake,and a comparison between the predicted and the observed results shows that the proposed models are reliable,and can be confidently used in mapping landslide potential.

Mechanical mechanism analysis of tension type anchor based on shear displacement method

Based on the fact that the shear stress along anchorage segment is neither linearly nor uniformly distributed, the load transfer mechanism of the tension type anchor was studied and the mechanical characteristic of anchorage segment was analyzed. Shear stress?strain relationship of soil surrounding anchorage body was simplified into three-folding-lines model consisting of elastic phase, elasto-plastic phase and residual phase considering its softening characteristic. Meanwhile, shear displacement method that has been extensively used in the analysis of pile foundation was introduced. Based on elasto-plastic theory, the distributions of displacement, shear stress and axial force along the anchorage segment of tension type anchor were obtained, and the formula for calculating the elastic limit load was also developed accordingly. Finally, an example was given to discuss the variation of stress and displacement in the anchorage segment with the loads exerted on the anchor, and a program was worked out to calculate the anchor maximum bearing capacity. The influence of some parameters on the anchor bearing capacity was discussed, and effective anchorage length was obtained simultaneously. The results show that the shear stress first increases and then decreases and finally trends to the residual strength with increase of distance from bottom of the anchorage body, the displacement increases all the time with the increase of distance from bottom of the anchorage body, and the increase of velocity gradually becomes greater.

A new analytical solution for calculation the displacement and shear stress of fully grouted rock bolts and numerical verifications

In presence of difficult conditions in coal mining roadways, an adequate stabilization of the excavation boundary is required to ensure a safe progress of the construction. The stabilization of the roadways can be improved by fully grouted rock bolt, offering properties optimal to the purpose and versatility in use. Investigations of load transfer between the bolt and grout indicate that the bolt profile shape and spacing play an important role in improving the shear strength between the bolt and the surrounding strata. This study proposes a new analytical solution for calculation displacement and shear stress in a fully encapsulated rock bolt in jointed rocks. The main characteristics of the analytical solution consider the bolt profile and jump plane under pull test conditions. The performance of the proposed analytical solution, for three types of different bolt profile configurations, is validated by ANSYS software. The results show there is a good agreement between analytical and numerical methods. Studies indicate that the rate of displacement and shear stress from the bolt to the rock exponentially decayed. This exponential reduction in displacement and shear stress are dependent on the bolt characteristics such as: rib height, rib spacing, rib width and grout thickness, material and joint properties.

STRESS ANALYSIS OF INJECTION MOLDED PARTS IN POST-FILLING STAGE

The linear isothermo-viscoelastic constitutive equation is established according to the principle of viscoelastic mechanics. Given the boundary conditions of the temperature field, the linear thermo-viscoelastic constitutive equation is established acording to the analysis of the thermorheologically simple. The stress analysis model is constructed on the base of some reasonable hypotheses which consider the restraint conditions of mold and the characteristics of injection molding in the post-filling stage. The mathematical model is calculated by the finite difference method. The results can help to predict the warpage of plastic products.

Algebraic Solution for the Forward Displacement Analysis of the General 6-6 Stewart Mechanism

The solution for the forward displacement analysis（FDA） of the general 6-6 Stewart mechanism（i.e., the connection points of the moving and fixed platforms are not restricted to lying in a plane） has been extensively studied, but the efficiency of the solution remains to be effectively addressed. To this end, an algebraic elimination method is proposed for the FDA of the general 6-6 Stewart mechanism. The kinematic constraint equations are built using conformal geometric algebra（CGA）. The kinematic constraint equations are transformed by a substitution of variables into seven equations with seven unknown variables. According to the characteristic of anti-symmetric matrices, the aforementioned seven equations can be further transformed into seven equations with four unknown variables by a substitution of variables using the Grobner basis. Its elimination weight is increased through changing the degree of one variable, and sixteen equations with four unknown variables can be obtained using the Grobner basis. A 40th-degree univariate polynomial equation is derived by constructing a relatively small-sized 9 × 9 Sylvester resultant matrix. Finally, two numerical examples are employed to verify the proposed method. The results indicate that the proposed method can effectively improve the efficiency of solution and reduce the computational burden because of the small-sized resultant matrix.

Stress analysis of functionally graded rotating discs: analytical and numerical solutions

This study deals with stress analysis of annular rotating discs made of functionally graded materials（FGMs）.Elasticity modulus and density of the discs are assumed to vary radially according to a power law function,but the material is of constant Poisson＇s ratio.A gradient parameter n is chosen between 0 and 1.0.When n = 0,the disc becomes a homogeneous isotropic material.Tangential and radial stress distributions and displacements on the disc are investigated for various gradient parameters n by means of the diverse elasticity modulus and density by using analytical and numerical solutions.Finally,a homogenous tangential stress distribution and the lowest radial stresses along the radius of a rotating disc are approximately obtained for the gradient parameter n = 1.0 compared with the homogeneous,isotropic case n = 0.This means that a disc made of FGMs has the capability of higher angular rotations compared with the homogeneous isotropic disc.

Evaluation of stress intensity factors for bi-material interface cracks using displacement jump methods

The aim of the present work is to investigate the numerical modeling of interfacial cracks that may appear at the interface between two isotropic elastic materials. The extended finite element method is employed to analyze brittle and bi-material interfacial fatigue crack growth by computing the mixed mode stress intensity factors(SIF). Three different approaches are introduced to compute the SIFs. In the first one, mixed mode SIF is deduced from the computation of the contour integral as per the classical J-integral method,whereas a displacement method is used to evaluate the SIF by using either one or two displacement jumps located along the crack path in the second and third approaches. The displacement jump method is rather classical for mono-materials,but has to our knowledge not been used up to now for a bimaterial. Hence, use of displacement jump for characterizing bi-material cracks constitutes the main contribution of the present study. Several benchmark tests including parametric studies are performed to show the effectiveness of these computational methodologies for SIF considering static and fatigue problems of bi-material structures. It is found that results based on the displacement jump methods are in a very good agreement with those of exact solutions, such as for the J-integral method, but with a larger domain of applicability and a better numerical efficiency(less time consuming and less spurious boundary effect).