Rheological properties and concentration evolution of thickened tailings under the coupling effect of compression and shear

Cemented paste backfill(CPB)is a key technology for green mining in metal mines,in which tailings thickening comprises the primary link of CPB technology.However,difficult flocculation and substandard concentrations of thickened tailings often occur.The rheological properties and concentration evolution in the thickened tailings remain unclear.Moreover,traditional indoor thickening experiments have yet to quantitatively characterize their rheological properties.An experiment of flocculation condition optimization based on the Box-Behnken design(BBD)was performed in the study,and the two response values were investigated:concentration and the mean weighted chord length(MWCL)of flocs.Thus,optimal flocculation conditions were obtained.In addition,the rheological properties and concentration evolution of different flocculant dosages and ultrafine tailing contents under shear,compression,and compression-shear coupling experimental conditions were tested and compared.The results show that the shear yield stress under compression and compression-shear coupling increases with the growth of compressive yield stress,while the shear yield stress increases slightly under shear.The order of shear yield stress from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Under compression and compression-shear coupling,the concentration first rapidly increases with the growth of compressive yield stress and then slowly increases,while concentration increases slightly under shear.The order of concentration from low to high under different thickening conditions is shear,compression,and compression-shear coupling.Finally,the evolution mechanism of the flocs and drainage channels during the thickening of the thickened tailings under different experimental conditions was revealed.

Study Two-Dimensional and Three-Dimensional of the Stress Concentration of the Traction Arm of the NEW HOLLAND TT75 Tractor in Service in CHAD

The New Holland TT75 tractors currently in service in Chad use a tractor arm with three holes, the middle one of which has recurrent failures due to traction. The purpose of this work is to use a finite element model to provide an improvement by modifying the geometric parameters to avoid premature failure of the tractor arms of the New Holland TT75. The ultimate force formula of Eurocode 3 was used to determine the maximum pressure to be applied and. A comparative traction study between the current arm and the proposed arm was performed, taking into account the variation in hole size, arm width and applied pressure for the determination of the stress concentration factor Kt. With the determination of Kt and for the arm width (w) less than or equal to 85 mm;the results showed that the proposed arm geometry is better.

SCATTERING OF FLEXURAL WAVES AND DYNAMIC STRESS CONCENTRATIONS IN MINDLIN'S THICK PLATES WITH A CUTOUT

Using the complex variable method and conformal mapping,scat- tering of flexural waves and dynamic stress concentrations in Mindlin's thick plates with a cutout have been studied.The general solution of the stress problem of the thick plate satisfying the boundary conditions on the contour of cutouts is obtained. Applying the orthogonal function expansion technique,the dynamic stress problem can be reduced into the solution of a set of infinite algebraic equations.As examples, numerical results for the dynamic stress concentration factor in Mindlin's plates with a circular,elliptic cutout are graphically presented in sequence.

Dynamic stress concentration and scattering of SH-wave by interface elliptic cylindrical cavity

In this paper,the dynamic stress concentration and scattering of SH-waves by bi-material structures that possess an interface elliptic cavity are investigated.First,by using the complex function method,the Green's function is constructed.This yields the solution of the displacement field for an elastic half space with a semi-elliptic canyon impacted by an anti-plane harmonic line source loading on the horizontal surface.Then,the problem is divided into an upper and lower half space along the horizontal interface,regarded as a harmony model.In order to satisfy the integral continuity condition, the unknown anti-plane forces are applied to the interface.The integral equations with unknown forces can be established through the continuity condition,and after transformation,the algebraic equations are solved numerically.Finally,the distribution of the dynamic stress concentration factor(DSCF)around the elliptic cavity is given and the effect of different parameters on DSCF is discussed.

Numerical Analysis of Stress Concentration in Non-uniformly Corroded Small-Scale Specimens

A numerical evaluation of stress concentrations of corroded plate surfaces of small-scale corroded steel specimens is compared with the experimentally estimated ones.Eleven specimens were cut from a steel box girder,which was initially corroded in real seawater conditions.The surface of all corroded specimens was analysed applying photogrammetry techniques,and a statistical description of an idealised corroded surface of each specimen was established.Fatigue lives of specimens are determined from the fatigue tests.Based on experimentally obtained fatigue lives,the stress concentration factors are calculated concerning the ideally smooth specimens.The correlation between the statistical parameters of the corroded specimen surfaces and the estimated stress concentration factors is analysed.Idealised corroded surfaces,converted in graphical format,are then used for the finite element modelling in ABAQUS software,and stress concentration factors are estimated from the finite element results.A convergence study is performed to determine the appropriate finite element mesh density.Comparison between experimentally obtained and numerically estimated stress concentration factors is performed as well as correlation analysis between actual and finite element predicted crack locations.

Elastic Wave Scattering and Dynamic Stress Concentrations around Double Holes in Piezoelectric Media

In this paper, on the basis of Liu’s complex function and conformal mapping methods, supplemented by local coordinate system method, e-type piezoelectric material and elastic wave scattering and dynamic stress concentrations problems with double holes question are studied, and an analytical solution is given to the problems. On the basis of multiple scattering of elastic wave theory, put forward the study about microscopic dynamics model to dynamic stress in the structure of piezoelectric composites as well as dynamic playing field. As an example, the numerical results of the dynamic stress distribution around the hole in case double equal diameter holes are given in the paper, and the influence of incident wave number and hole-spacing parameters on the dynamic stress concentration factor is analyzed.

Using Refined Theory to Studied Elastic Wave Scattering and Dynamic Stress Concentrations in Plates with Two Cutouts

In this paper, based on complex variables and conformal mapping methods, using the refined dynamic equation of plates, elastic wave scattering and dynamic stress concentrations in plates with two cutouts were studied. Applying the orthogonal function expansion method, the problem to be solved can be reduced into the solution of a set of infinite algebraic equations. According to free boundary conditions, numerical results of dynamic moment concentration factors in thick plates with two circular cutouts analyze that: there will be more complex interaction changes between two-cutout situation than single cutout situation. In the case of low frequency or high frequency and thin plate, the hole-spacing in the absence of coupling interactions was larger or smaller. The numerical results and method can be used to analyze the dynamics and strength of plate-like structures.

ANALYTICAL SOLUTIONS TO STRESS CONCENTRATION PROBLEM IN PLATES CONTAINING RECTANGULAR HOLE UNDER BIAXIAL TENSIONS

The stress concentration problem in structures with a circular or elliptic hole can be investigated by analytical methods. For the problem with a rectangular hole, only approximate results are derived. This paper deduces the analytical solutions to the stress concentration problem in plates with a rectangular hole under biaxial tensions. By using the U-transformation technique and the finite element method, the analytical displacement solutions of the finite element equations are derived in the series form. Therefore, the stress concentration can then be discussed easily and conveniently. For plate problem the bilinear rectangular element with four nodes is taken as an example to demonstrate the applicability of the proposed method. The stress concentration factors for various ratios of height to width of the hole are obtained.

Characterization of Stress Concentration by Tangential Component Hp(x) of Metal Magnetic Memory Signals

The correlation between the stress concentration and the spontaneous magnetic signals of metal magnetic memory(MMM) was investigated via tensile tests. Sheet specimens of the Q235 steel were machined into standard bars with rectangular holes to obtain various stress concentration factors. The tangential component Hp(x) of MMM signals and its related magnetic characteristic parameters throughout the loading process were presented and analyzed. It is found that the tangential component Hp(x) is sensitive to the abnormal magnetic changes caused by the local stress concentration in the defect area. The minimum magnetic field is positively correlated to the magnitude of the load and the distance from the notch. The tangential magnetic stress concentration factor presents good numerical stability during the entire loading process, and can be used to evaluate the stress concentration factor. The results obtained will be a complement to the MMM technique.

Magnetic field properties caused by stress concentration

Measurements of the effects of tensile stress on magnetic field properties, infrared thermography and (acoustic) emission of a cuboid sample with an elliptical hole in its center were presented. The tensile stress was applied perpendicularly to the sample by electro-tension machine according to a step-loading curve. The changes of the sample temperature was recorded by an infrared thermography system and the noise of domain reversal was inspected by two acoustic probes, which were placed on each end of the sample near the collets of the electro-tension machine, when the sample was in loading process. The magnetic fields on the surface of the sample were inspected with 8 mm lift-off when the loads were held. Valuable information about the changes of domains was obtained from analysis of acoustic emission signals in loading process. Infrared images of the sample provided complementary information about the state of the sample. The results show that stress concentration in ferromagnetic material affects the direction and structure of domain and generates net magnetic moment on its surface. The distribution and magnitude of the net magnetic moment are correlative with those of stress.

Coupling control on pillar stress concentration and surface cracks in shallow multi-seam mining

In order to ensure safe mining and reduce surface damage in shallow multi-seam mining,the failure characteristics of interburden strata with different coal pillars offset distances between pillars in the upper and lower seams,the distribution characteristics of stress concentration in coal pillars,and the development characteristics of stratum cracks and subsidence were investigated by physical and UDEC2D simulation.Meanwhile,the effect of different coal pillar offset distances on stress concentration of coal pillar and development of stratum cracks were studied.Based on those results,a formula for safe mining and reducing surface damage was established,which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seam.According to the results,the optimal coal pillar offset distance(the side to side horizontal distance of the upper and lower coal pillars)between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage.The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

ANALYTICAL VARIATIONAL METHOD OF SOLUTION FOR STRESS CONCENTRATION FACTORS OF FINITE PLATES WITH A PIN HOLE

First of all, Laurent series expansions of stress and displacement fields satisfying all the governing equations of plane problems in theory of elasticity are derived. Next, the variational method is applied to satisfy the boundary conditions of a plate with a pin hole. Then, the coefficients in Laurent series and the stress concentration factor can be determined. Finally, the convergency tests and systematical results are given for engineering applications.

STUDY ON STRESS CONCENTRATIONS IN AN INTRAPLY HYBRID COMPOSITE SHEET

A reasonably, simply and accurately modified shear-lag model was proposed. Based on the model, the stress redistributions due to the failure of some fibers in an intraply hybrid composite under tension were analyzed. The results show that the present calculating stress concentration factors very coincide with Fukuda and Chou's results, thus verifying the reasonableness and correctness of the present model and methods.

A biarc-based shape optimization approach to reduce stress concentration effects

In order to avoid stress concentration, the shape boundary must be properly designed via shape optimiza- tion. Traditional shape optimization approach eliminates the stress concentration effect by using free-form curve to present the design boundaries without taking the machin- ability into consideration. In most numerical control （NC） machines, linear as well as circular interpolations are used to generate the tool path. Non-circular curves, such as non- uniform rotational B-spline （NURBS）, need other more ad- vanced interpolation functions to formulate the tool path. Forming the circular tool path by approximating the opti- mal free curve boundary with arcs or biarcs is another op- tion. However, these two approaches are both at a cost of sharp expansion of program code and long machining time consequently. Motivated by the success of recent researches on biarcs, a reliable shape optimization approach is pro- posed in this work to directly optimize the shape boundaries with biarcs while the efficiency and precision of traditional method are preserved. Finally, the approach is validated by several illustrative examples.

Research on stress concentration factor of tube joints under pure bending and torsion loading

For fatigue strength design and evaluation as well as for multiaxial fatigue tests analysis of welded structures, the stress concentration factor(SCF) at the weld must be known. In the present study, two common models of multiaxial fatigue tests, tube-plate(TP) model and tube-tube(TT) model are selected as the research objects. SCFs of the two models with various geometric parameters under pure bending and pure torsion loading have been investigated by conducting a series of three-dimensional(3 D) finite element models based on linear elasticity theory. The effect of weld width(w), plate thickness(t), weld toe notch radius(r), and reinforcement angle(θ) on SCF is assessed. The quadratic parametric equations based on t/r are proposed to predict SCFs of the two models, which reveal satisfactory accuracy.

Parametric Equation of Stress Concentration Factor for Circular X-Joints Under Axial Loads

In engineering practice, tubular X-joints have been widely used in offshore structures. The fatigue failure of tubular X-joints in offshore engineering is mainly caused by axial tensile stress. In this study, the stress concentration factor distribution along the weld toe in the hot spot stress region for tubular X-joints subject to axial loads have been analyzed by use of finite element method. Through numerical analysis, it has been found that the peak stress concentration factor is located at the saddle position. Thereafter, 80 models have been analyzed, and the effect of the geometric parameters of a tubular X-joint on the stress concentration factor has been investigated. Based on the experimental values of the numerical stress concentration factor, a parametric equation to calculate the stress concentration factor of tubular X-joints has been proposed. The accuracy of this equation has been verified against the requirement of the Fatigue Guidance Review Panel, and the proposed equation is found capable of producing reasonably accurate stress concentration factor values for tubular X-joints subject to axial loads.

Effect of Surface Topography on Stress Concentration Factor

Neuber rule and Arola-Ramulu model are widely used to predict the stress concentration factor of rough specimens. However, the height parameters and effective valley radius used in these two models depend strongly on the resolution of the roughness-measuring instruments and are easily introduce measuring errors. Besides, it is difficult to find a suitable parameter to characterize surface topography to quantitatively describe its effect on stress concentration factor. In order to overcome these disadvantages, profile moments are carried out to characterize surface topography, surface topography is simulated by superposing series of cosine components, the stress concentration factors of different micro cosine-shaped surface topographies are investigated by finite element analysis. In terms of micro cosine-shaped surface topography, an equation using the second profile moment to estimate the stress concentration factor is proposed, predictions for the stress concentration factor using the proposed expression are within 10% error compared with the results of finite element analysis, which are more accurate than other models. Moreover, the proposed equation is applied to the real surface topography machined by turning. Predictions for the stress concentration factor using the proposed expression are within 10% of the maximum stress concentration factors and about 5% of the effective stress concentration factors estimated from the finite element analysis for three levels of turning surface topographies under different simulated scales. The proposed model is feasible in predicting the stress concentration factors of real machined surface topographies.

Influence of Soft Filler on Stress Concentration Factor of Elliptic Holes in a Rectangular Plate

Finite element models were established to analyze the influence of soft filler on stress concentration for a rectangular plate with an elliptic hole in the center. The influence was quantified by means of stress concentration factor (SCF). Seven shape factors of the elliptic hole and three levels of elasticity modulus of the soft filler were considered. The reduction coefficient and sensitivity index of SCF are the two indicators in evaluating the influence of soft filler. It was found that the reduction coefficient of SCF increases significantly as the shape factor and the elasticity modulus of the filler increase, indicating that soft filler can reduce the concentrated stress effectively, especially when the shape factor is great. Analysis for the sensitivity index of SCF indicates that SCF is more sensitive to materials with small elasticity modulus than to materials with large one.

AN ANALYSIS FOR DIFFRACTION OF FLEXURAL WAVES AND DYNAMIC STRESS CONCENTRATIONS IN THICK PLATES WITH A CAVITY

By using the complex variable method and conformal mapping, the diffraction of flexural waves and dynamic stress concentrations in thick plates with a cavity have been studied. A general solution of the stress problem of the thick plate satisfying the boundary conditions on the contour of an arbitrary cavity is obtained. By employing the orthogonal function expansion technique, the dynamic stress problem can be reduced to the solution of an infinite algebraic equation series. As an example, the numerical results for the dynamic stress concentration factor in thick plates with a circular, elliptic cavity are graphically presented. The numerical results are discussed.

DYNAMIC STRESS CONCENTRATIONS IN AMBARTSUMIAN'S PLATE WITH A CUTOUT

Based on the motion equations of flexural wave in Ambartsumian' s plates including the effects of transverse shear deformations,by using perturbation method of small parameter,the scatter- ing of flexural waves and dynamic stress concentrations in the plate with a cutout have been studied. The asypmtotic solution of the dynamic stress problem is obtained.Numerical results for the dynamic stress concentration factor in Ambartsumian's plates with a circular cutout are graphically presented and discussed.