Time-sensitivity of the Kaiser effect of acoustic emission in limestone and its application to measurements of in-situ stress

Measuring in-situ stress by using the Kaiser effect in rocks has such advantages as timeefficiency, low cost and little limitation, but the precision of the method is dependent on rock properties and delay time of the measurement. In this paper, experiments on the Kaiser effect in limestones were performed, and it was found that the limestones had good ability to retain a memory of their recent stress history and high time-sensitivity. The longer the experiment was delayed from the extraction of the stone, the larger the Felicity ratio was. As the Felicity ratio approached l, significant Kaiser effect was observed. In-situ stress should be determined by the limestone measurements when the delay time was 40-120 days. Finally, the in-situ stress in a limestone formation could be successfully measured in practice.

TIME-TEMPERATURE-STRESS EQUIVALENCE AND ITS APPLICATION TO NONLINEAR VISCOELASTIC MATERIALS

Stress-dependence of the intrinsic time of viscoelastic materialsis investigated. The influence of stress level on the intrinsic timeis considered to be similar to that of temperature, pressure, solventcon- centration, damage and physical aging. Thetime-temperature-stress equivalence principle is proposed, byemploying which, the creep curves at different temperatures andstress level can be shifted into a master curve at referencetemperature and stress level.

Acoustic emission characteristics and stress release rate of coal samples in different dynamic destruction time

Considering the importance of the prediction of rock burst disasters, and in order to grasp the law of acoustic emission(AE) of coal samples in different dynamic destruction time, the SH-II AE monitoring system was adopted to monitor the failure process of coal samples. The study of the change rule of the AE numbers, energy, ‘b' value and spectrum in the micro crack propagation process of the coal samples shows that as dynamic damage time went by, AE presented high-energy counts and the accumulated counts increased during the compression phase. The AE energy and cumulative counts increased during the elastic stage. The AE blank area increased gradually and the blank lines were more and more obvious in the molding stage. The AE counts and energy showed a trend of decrease in the residual damage phase.AE ‘b' values gradually became sparse, and the large scale cracks percentage compared with micro cracks decreased and the degree of damage decreased. The AE frequency spectrum peak went from the residual damage phase to the molding phase, and finally it was nearly stable, besides the bandwidth of the main frequency is gradually narrowed. Also, the frequency peak changed from single peak frequency to bi-peak frequency and to the single peak frequency. Uniaxial compressive strength is more sensitive than the elastic modulus to dynamic damage time.

Stochastic transient analysis of thermal stresses in solids by explicit time-domain method

Stochastic heat conduction and thermal stress analysis of structures has received considerable attention in recent years.The propagation of uncertain thermal environments will lead to stochastic variations in temperature fields and thermal stresses.Therefore,it is reasonable to consider the variability of thermal environments while conducting thermal analysis.However,for ambient thermal excitations,only stationary random processes have been investigated thus far.In this study,the highly efficient explicit time-domain method(ETDM)is proposed for the analysis of non-stationary stochastic transient heat conduction and thermal stress problems.The explicit time-domain expressions of thermal responses are first constructed for a thermoelastic body.Then the statistical moments of thermal displacements and stresses can be directly obtained based on the explicit expressions of thermal responses.A numerical example involving non-stationary stochastic internal heat generation rate is investigated.The accuracy and efficiency of the proposed method are validated by comparison with the Monte-Carlo simulation.

Susceptible time window and endurable duration of cotton fiber development to high temperature stress

The development of the cotton fiber is very sensitive to temperature variation, and high temperature stress often causes reduced fiber yield and fiber quality. Short-term high temperature stress often occurs during cotton production, but little is known about the specific timing and duration of stress that affects fiber development. To make this clear, pot experiments were carried in 2014 and 2015 in a climate chamber using cotton cultivars HY370WR（less sensitive variety） and Sumian 15（heat sensitive variety）, which present different temperature sensitivities. Changes of the most important fiber quality indices（i.e., fiber length, fiber strength and marcironaire） and three very important fiber development components（i.e., cellulose, sucrose and callose） were analyzed to define the time window and critical duration to the high temperature stress at 34°C（max38°C/min30°C）. When developing bolls were subjected to 5 days of high temperature stress at different days post-anthesis（DPA）, the changes（Δ%） of fiber length, strength and micronire, as a function of imposed time followed square polynomial eq. as y=a＋bx＋cx^2, and the time around 15 DPA was the most sensitive period for fiber quality development in response to heat stress. When 15 DPA bolls were heat-stressed for different durations（2, 3, 4, 5, 6, 7 days）, the changes（Δ%） of fiber length, strength and micronire, as a function of stress duration followed logistic equations y=A_1-A_2/1＋（x/x_0）~p＋A_2. Referred to that 5, 10 and 15% are usually used as criteria to decide whether techniques are effective or changes are significant in crop culture practice and reguard to the fiber quality indices change range, we suggested that 5% changes of the major fiber quality indices（fiber length, fiber strength and micronaire） and 10% changes of fiber development components（cellulose, sucrose and callose） could be taken as criteria to judge whether fiber development and fiber quality have been significantly affected by high temperature stress. The key time window for cotton fiber development in response to the high temperature stress was 13–19 DPA, and the critical duration was about 5 days.

Design of a Prognostics and Health Management System for Electromechanical Equipment Through Time Stress Analysis

Time stress includes all kinds of environment and operating stress such as shock, vibration, temperature and electric current that the electromechanical system suffers in the manufacture, transport and operating process. In this paper, the conception of time stress and prognostics and health management （ PHM） system are introduced. Then, in order to improve the false alarm recognition and fault prediction capabilities of the electromechanical equipment, a novel PHM architecture for electromechanical equipment is put forward based on a built-in test （BIT） system design technology and time stress analysis method. Finally, the structure, the design and implementing method and the functions of each module of this PHM system are described in detail.

TECHNOLOGY OF QUANTITATIVE ANALYSIS ON VIBRATORY STRESS RELIEF BASED ON ULTRASONIC TIME-OF-ARRIVAL METHOD

The effect of vibratory stress relief （VSR） is usually evaluated with the indirect method of observing the change of amplitude frequency response characteristics of structures. A new kind of evaluating method of VSR based on the ultrasonic time-of-arrival method （UTM）, which can obtain the residual stress directly through measuring the propagation time of ultrasonic wave in the material, is presented. At first, the principle of the measuring method of residual stress based on UTM is analyzed. Then the measuring system of the method is described, which is in virtue of ultrasonic flaw detector and high-sampling-rate digital oscillograph. And a set of calibration system that contains a piece of standard specimen is also introduced. Experimental results prove the relation between the residual stress and the propagation time of ultrasonic in workpieces. Finally, the measuring and calibration systems are applied in evaluating the effect of VSR. The final test results show that the method is effective.

Reference genes for quantitative real-time PCR analysis and quantitative expression of P5CS in Agropyron mongolicum under drought stress

Reference genes, stably expressing in different tissues and cells, are commonly used as the references in expression analysis. Selecting the optimum reference gene is crucial to the success of experiments. In this study, the expression stabilities of nine common reference genes, including ACT2, 18 S r RNA, APRT, EF-1α, RNA POL II, TUBα, TUBβ, GAPDH and TLF of Agropyron mongolicum, were studied under drought condition. Among them, 18 S r RNA was found to be the most optimum reference gene under drought stress by the analyzing of ge Norm and Norm Finder software. Quantitative expression levels of P5 CS using 18 S r RNA as the reference gene, and proline contents under drought stress in A. mongolicum were further operated, and we found the expression level of P5 CS gene and proline content had a significantly positive relationship（R^2=0.7763, P〈0.05）. This study established and validated 18 S r RNA as the reference genes in A. mongolicum under drought stress, providing a powerful tool for the quantitative expression analysis of drought genes in A. mongolicum.

The Effect of Unloading Positions and Times on Sheet Metal’s Stress-Strain Curve

The loading-unloading-reloading process could affect the tensile deformation of metals with the combined function of stress relaxation and work hardening, which has been reported in multiple experiments. Nevertheless, the effects of different unloading positions and unloading times have not been investigated. In this study, unloading-reloading tests on three materials (AL6061, HSLA and Q195) were conducted. The stress exhibits a rapid rise momentarily upon reloading and stabilizes afterward while the post stress-strain curve deviates up or down from the monotonic tensile curve. The ductility is enhanced by the unloading-reloading process in general. Different unloading positions and unloading times have different degrees of influence on the stretching of these metals. The effect of loading conditions on a medium manganese steel was further studied. The functions to modify the post stress-strain relationship after unloading-reloading were established.

Methods for Reliability Assessment under Irregular Time-Varying-Stress Degradation Testing

Degradation tests are often used to assess the reliability of products with long failure-time or few test units. Much of the previous work on reliability assessment methods has focused on constant-stress degradation test( CSDT) and accelerated degradation test( ADT), mainly under the constant, step or progressive stresses. However,in actual testing environments,some stresses are difficult to control and vary with time irregularly,which are quite different from the three stresses mentioned above. In this paper a new approach was presented for reliability assessment with degradation data under irregular time-varying-stress( ITVS).Firstly,the conventional degradation path modeling method was improved by taking into account the influences of the variable stress on the degradation variable. Then,an example was conducted to show the effectiveness of our improved model.

Experimental study on time-dependent stress and strain of in-plane shear(ModeⅡ) fracture process of rock

Shear-box test with strain measurement was used to study time-dependent stress and strain of in-plane shear(Mode Ⅱ) fracture process of rock and to reveal the mechanism of Mode Ⅱ fracture.Numerical results show that the maximum shear stress τmax at the crack tip is much larger than the maximum tensile stress σ1 and the ratio of τmax/σ1 is about 5,which favors Mode Ⅱ fracture of rock.Test results indicate that the strain-time curve comprises three stages:the linear deformation stage,the micro-cracking stage and the macroscopic crack propagation.The strain in the direction of the original notch plane is negative,due to restraining effect of compressive loading applied to the original notch plane.Both σ1 and τmax are increased as the load increases,but the slope of τmax is larger than that of σ1 and the value of τmax is always larger than that of σ1.Therefore,τmax reaches its limited value at peak load before σ1 and results in Mode Ⅱ fracture of rock.Shear-box(i.e.compression-shear) test becomes a potential standard method for achieving the true Mode Ⅱ fracture and determining Mode Ⅱ fracture toughness of rock.

Modeling of Surface Waves in a Fluid Saturated Poro-Elastic Medium under Initial Stress Using Time-Space Domain Higher Order Finite Difference Method

In this present context, mathematical modeling of the propagation of surface waves in a fluid saturated poro-elastic medium under the influence of initial stress has been considered using time dependent higher order finite difference method (FDM). We have proved that the accuracy of this finite-difference scheme is 2M when we use 2nd order time domain finite-difference and 2M-th order space domain finite-difference. It also has been shown that the dispersion curves of Love waves are less dispersed for higher order FDM than of lower order FDM. The effect of initial stress, porosity and anisotropy of the layer in the propagation of Love waves has been studied here. The numerical results have been shown graphically. As a particular case, the phase velocity in a non porous elastic solid layer derived in this paper is in perfect agreement with that of Liu et al. (2009).

Development of a time-dependent energy model to calculate the mining-induced stress over gates and pillars

Generally, longwall mining-induced stress results from the stress relaxation due to destressed zone that occurs above the mined panel. Knowledge of induced stress is very important for accurate design of adjacent gateroads and intervening pillars which helps to raise the safety and productivity of longwall mining operations. This study presents a novel time-dependent analytical model for determination of the longwall mining-induced stress and investigates the coefficient of stress concentration over adjacent gates and pillars. The model is developed based on the strain energy balance in longwall mining incorporated to a rheological constitutive model of caved materials with time-varying parameters. The study site is the Tabas coal mine of Iran. In the proposed model, height of destressed zone above the mined panel, total longwall mining-induced stress, abutment angle, induced vertical stress, and coefficient of stress concentration over neighboring gates and intervening pillars are calculated. To evaluate the effect of proposed model parameters on the coefficient of stress concentration due to longwall mining, sensitivity analysis is performed based on the field data and experimental constants. Also, the results of the proposed model are compared with those of existing models. The comparative results confirm a good agreement between the proposed model and the in situ measurements. According to the obtained results, it is concluded that the proposed model can be successfully used to calculate the longwall mining-induced stress. Therefore, the optimum design of gate supports and pillar dimensions would be attainable which helps to increase the mining efficiency.

The Mathematical Modelling for Studying the Influence of the Initial Stresses and Relaxation Times on Reflection and Refraction Waves in Piezothermoelastic Half-Space

The present paper concentrates on the study of reflection and refraction phenomena of waves in pyroelectric and piezo-electric media under initial stresses and two relaxation times influence by apply suitable conditions. The generalized theories of linear piezo-thermoelasticity have been employed to investigate the problem. In two-dimensional model of transversely isotropic piezothermoelastic medium, there are four types of plane waves quasi-longitudinal (qP), quasi-transverse (qSV), thermal wave (T-mode), and potential electric waves (φ-mode) The amplitude ratios of reflection and refraction waves have been obtained. Finally, the results in each case are presented graphically.

THE ANALYSIS OF DYNAMIC STRESS INTENSITY FACTOR FOR SEMI-CIRCULAR SURFACE CRACK USING TIME-DOMAIN BEM FORMULATION

The time-domain BEM was developed to analyze the dynamic stress intensity factor ( DSIF) of 3-D elastodynamic crack problems. To simulate the stress singularity along the front of a crack, eight-node isoparametric singular elements were used, and the DSIF for a semi-circular surface crack was firstly calculated based on displacement equation using the time-domain BEM formulation. The new scheme to determine the time step was brought forward. By the dynamic analysis program of time-domain BEM compiled by its, several numerical examples are presented, which demonstrate the unconditional stability and high accuracy of time-domain BEM applied to 3-D elastodynamic crack problems.

地应力影响下的五孔掏槽爆破岩石损伤效应研究

在地下矿山开采过程中,地应力对巷道掘进效率的影响日益显著。本研究以某地下铁矿为研究对象,采用有限元软件LS-DYNA模拟不同地应力条件下五孔掏槽爆破掏槽孔孔间延期时间对岩石损伤程度的影响。通过现场爆破实验和块度识别软件验证模拟结果,探究了地应力、孔间延期时间与岩石损伤程度之间的关系。研究结果表明,地应力由0 MPa增加到10 MPa,五孔掏槽爆破掏槽孔最佳延期时间由60 ms减少为10 ms,相应的岩石损伤程度降低79%。地应力对爆破远区岩石裂纹的发育影响较大,而对近区影响较小。现场实验进一步证实了数值模拟的结论,表明可以根据实际地应力大小合理设置延期时间,有效降低大块率,提高爆破效率。

Evaluation of Stress among 100 Moroccan Orthodontists

Stress is associated with many professions including dental surgery. It has been the subject of several studies. However, its evaluation in orthodontics has not been sufficiently studied. Some studies that have described the stressful aspects of dentistry have reported the involvement of orthodontists, but no studies have been conducted in Morocco. The purpose of this study is to evaluate professional stress in orthodontics in Morocco. We conducted a descriptive and sectional study through a survey distributed to one hundred private orthodontist practitioners in Casablanca, Morocco. Stress signs were observed in 44% of the orthodontists. The most prominent factors of stress in orthodontics are related to patients and time. Experience of practitioners has been identified as the only factor significantly influencing their perception of stress. Thus, clinical competence and proper management of practice are the best ways to deal with daily stress in orthodontic practice.

A Simplified Nonlinear Generalized Maxwell Model for Predicting the Time Dependent Behavior of Viscoelastic Materials

In this paper, a simple nonlinear Maxwell model consisting of a nonlinear spring connected in series with a nonlinear dashpot obeying a power-law with constant material parameters, for representing successfully the time-dependent properties of a variety of viscoelastic materials, is proposed. Numerical examples are performed to illustrate the sensitivity of the model to material parameters.

5-hydroxymethyl-2-furfural prolongs survival and inhibits oxidative stress in a mouse model of forebrain ischemia

In the present study, we hypothesized that 5-hydroxymethyl-2-furfural could attenuate ischemic brain damage by reducing oxidative injury. Thus, mice were subjected to bilateral common carotid artery occlusion to establish a model of permanent forebrain ischemia. The mice were intraperitoneally injected with 5-hydroxymethyl-2-furfura130 minutes before ischemia or 5 minutes after ischemia. The survival time of mice injected with 5-hydroxymethyl-2-furfural was longer compared with untreated mice. The mice subjected to ischemia for 30 minutes and reperfusion for 5 minutes were intraperitoneally injected with 5-hydroxymethyl-2-furfural 5 minutes prior to reperfusion, which increased superoxide dismutase content and reduced malondialdehyde content, similar to the effects of Edaravone, a hydroxyl radical scavenger used for the treatment of stroke. These findings indicate that intraperitoneal injection of 5-hydroxymethyl-2-furfural can prolong the survival of mice with permanent forebrain ischemia. This outcome may be mediated by its antioxidative effects.

Effects of stress and physical ageing on nonlinear creep behavior of poly(methyl methacrylate)

The effects of stress,ageing time and ageing temperature on creep behavior of poly(methyl methacrylate) were studied.After annealing above its glass transition temperature for a period of time to eliminate the stress and thermal history,the specimens were quenched and aged at various ageing temperatures for different ageing time,and then the short-term creep tests under different stress levels were carried out at room temperature.The creep strains were modeled by means of time-ageing time equivalence and time-stress equivalence,and the master creep curves were constructed via ageing time shift factors and stress shift factors.The results indicate that the creep rate increases with stress,while decreases with ageing time,and the ageing temperature history obviously affects the creep rate.For linear viscoelastic material,the ageing shift rate is independent on imposed stress,while for nonlinear viscoelastic material,the ageing shift rate decreases with increasing stress.The unified master creep curve up to 540 d at reference state was constructed by shifting the creep curves horizontally along the logarithmic time axis to overlap each other.It is demonstrated that the time-stress equivalence,united with the time-ageing time equivalence,provides an effective accelerated characterization technique in the laboratory to evaluate the long-term creep behavior of physical ageing polymers.