Three-Dimensional Analysis of Rolling by Twin Shear Stress Yield Criterion

Using the twin shear stress yield criterion, the surface integral of the co-line vectors, and the integration depending on upper limit, Kobayashi＇s three-dimensional velocity field of rolling was analyzed and an analytical expression of rolling torque and single force was obtained. Through redoing the same experiment of rolling pure lead as Sims, the calculated results by the above expression were compared with those of Kobayashi and Sims formulae. The results show that the twin shear stress yield criterion is available for rolling analysis and the calculated results by the new formula are a little higher than those by Kobayashi and Sims ones if the reduction ratio is less than 30%.

Estimating the yield stress of soft materials via laser-induced breakdown spectroscopy

Taking three typical soft samples prepared respectively by loose packings of 77-,95-,and 109-μm copper grains as examples,we perform an experiment to investigate the energy-dependent laser-induced breakdown spectroscopy(LIBS)of soft materials.We discovered a reversal phenomenon in the trend of energy dependence of plasma emission intensity:increasing initially and then decreasing separated by a well-defined critical energy.The trend reversal is attributed to the laser-induced recoil pressure at the critical energy just matching the sample's yield strength.As a result,a one-to-one correspondence can be well established between the samples'yield stress and the critical energy that is easily obtainable from LIBS measurements.This allows us to propose an innovative method for estimating the yield stress of soft materials via LIBS with attractive advantages including in-situ remote detection,real-time data collection,and minimal destructive to sample.

Stresses in the Scapular Fossa Do Not Exceed the Yield Stress When Elevated up to 135 Degrees of Abduction after Reverse Shoulder Arthroplasty

Reverse shoulder arthroplasty (RSA) is an effective treatment for rotator cuff tears. Despite its advantages, complications occur at a high rate. Complications requiring revision include a high rate of base plate failure, 38% of which are due to instability. The primary stability the base plate ensures is a crucial factor and, thus, is the subject of much debate in clinical studies and biomechanical research. This study is aimed to provide data that will contribute to the base plate’s pri-mary stability and glenoid longevity by clarifying the stresses at the scapular fossa and base plate interface associated with elevation after RSA. A 3D finite element model was created from the DICOM data for the scapulohumeral joint and SMR shoulder system. For loading conditions, 30 N was applied for each posi-tion with abduction angles of 0, 45, 90, and 135 degrees. A three-dimensional fi-nite element analysis was performed using the static implicit method with LS-DYNA. The von Mises stresses in the scapular fossa were found not to exceed the yield stress on the bone even after elevation to an abduction angle of 135 de-grees after RSA. It is rough to uniformly compare the yield stress and the von Mises stress, but it was inferred that the possibility of fracture is low unless a large external force is applied. A maximum von Mises stress showed 0 degrees of abduction, suggesting that the lowered position is in a more severe condition than the elevated position. If better improvement is desired, it may be necessary to devise ways to reduce the stress on the upper screw. .

Use of piezocone tests to predict consolidation yield stress and overconsolidation ratio of lagoonal deposit soil

Existing empirical methods for interpreting the consolidation yield stress and the overconsolidation ratio （OCR） in clays from piezocone tests are briefly reviewed. It can be seen that no universal correlation exists for all worldwide sites. However, for a given clay deposit, there does exist a most appropriate method to reflect the consolidation yield stress and the OCR based on piezocone test data. Three empirical methods are compared based on the piezocone test data collected on Lixia River lagoonal deposit soil sites in the north of Jiangsu province. The objective of this study is to evaluate the validity of the existing relationships linking the consolidation yield stress to piezocone test data and identify the appropriate method for Lixia River lagoonal deposit soil. It is shown that the correlation based on the net tip resistance has much higher accuracy for estimating the consolidation yield stress of lagoonal deposit soil than other methods.

Study on the Effects of Chinese Herb Additive on Milk Yield and Anti-heat Stress Ability of Holstein Cow

[Objective] The research aimed to explore the effects of Chinese herb additive on milk yield and anti-heat stress ability of Holstein cow.[Method] 36 Holstein cows with similar birth order and milk yield were equally and randomly divided into 3 groups which were control group, Chinese medicine Ⅰ group and Chinese medicine Ⅱ group. In control group, cows were fed with basic feed, while in Chinese medicine Ⅰ group, cows were fed with basic feed containing 4% compound Chinese herb additive and in Chinese medicine Ⅱ group, cows were fed with basic feed containing 3% compound Chinese herb additive.All cows in the 3 groups were analyzed comparatively.[Result] Adding some compound Chinese herb additive into basic feed would increase milk yield and anti-heat stress ability of Holstein cow,besides,it also could decrease cow diseases such as cow mastitis.Chinese medicine Ⅰ would generate the highest economic benefit of practical production.[Conclusion] Adding Chinese herb additive into basic feed is an effective way for reliefing heat stress and increasing milk yield.

Effect of particle gradation characteristics on yield stress of cemented paste backfill

Along with slurry concentration and particle density,particle size distribution(PSD)of tailings also exerts a significant influence on the yield stress of cemented paste,a non-Newtonian fluid.In this work,a paste stability coefficient(PSC)was proposed to characterize paste gradation and better reveal its connection to yield stress.This coefficient was proved beneficial to the construction of a unified rheological model,applicable to different materials in different mines,so as to promote the application of rheology in the pipeline transportation of paste.From the results,yield stress showed an exponential growth with increasing PSC,which reflected the proportion of solid particle concentration to the packing density of granular media in a unit volume of slurry,and could represent the properties of both slurry and granular media.It was found that slurry of low PSC contained extensive pores,generally around 20μm,encouraging free flow of water,constituting a relatively low yield stress.In contrast,slurry of high PSC had a compact and quite stable honeycomb structure,with pore sizes generally<5μm,causing the paste to overcome a higher yield stress to flow.

GENERALIZED TWIN SHEAR STRESS YIELD CRITERION AND ITS GENERALIZATION

Ⅰ. INTRODUCTION The yield criterion or' materials under combined stresses is the important foundation for the research of constitutive law of materials, and widely used in the mechanics of solids, the strength of structures and the elasto-plastic analysis of structures. The three present

Changes in underflow solid fraction and yield stress in paste thickeners by circulation

The trouble-free and efficient operation of paste thickeners requires an optimal design and the cooperation of each component.When underflow discharging is suspended,alleviating the vast torque that the remaining solids within the thickeners may place on rakes mainly lies in the circulation unit.The mechanism of this unit was analyzed,and a mathematical model was developed to describe the changes in underflow solid content and yield stress.The key parameters of the circulation unit,namely,the height and flow rate,were varied to test its performance in the experiments with a self-designed laboratorial thickening system.Results show that the circulation unit is valid in reducing underflow solid fraction and yield stress to a reasonable extent,and the model could be used to describe its efficiency at different heights and flow rates.A suitable design and application of the circulation unit contributes to a cost-effective operation of paste thickeners.

Evaluation of time-dependent rheological properties of cemented paste backfill incorporating superplasticizer with special focus on thixotropy and static yield stress

Superplasticizers are widely used to reduce the pipe flow resistance of cemented paste backfill(CPB), which is characterised by high concentration and high yield stress. This study aimed to assess the time-dependent rheological properties of CPB containing superplasticizer, with special focus on static yield stress and thixotropy. The results indicate that with the increase of the superplasticizer dosage, the static yield stress, dynamic yield stress and thixotropy of CPB decreased significantly, while the plastic viscosity decreased slightly. The curing time has a significant effect on the static yield stress, dynamic yield stress and thixotropy of CPB containing superplasticizer, which increase by 46.6%-87.1%,15.2%-35.6% and 79.4%-138.2%, respectively, within 2 h. The static yield stress, dynamic yield stress and thixotropy of CPB without superplasticizer only increase by 4.9%, 6.3% and 16.1%, respectively, within 2 h. The curing time has a significant influence on the plastic viscosity of CPB regardless of superplasticizer addition, the plastic viscosity increases by 13.2%-19.7% within 2 h. Regardless of superplasticizer dosage, plotting of both static yield stress and dynamic yield stress versus thixotropy produces clearly linear curves. The findings of this study are conducive to the design of pipe transportation of CPB containing superplasticizer.

Synergistic effect of magnetic field and nanocomposite pour point depressant on the yield stress of waxy model oil

Yield stress,as the key parameter to characterize the network strength of waxy oil,is important to the petroleum pipeline safety.Reducing the yield stress of waxy oil is of great significance for flow assurance.In this study,the effect of alternating magnetic field(intensity,frequency)on the yield stress of a waxy model oil with nanocomposite pour point depressant(NPPD)is systematically investigated.An optimum magnetic field intensity and frequency is found for the reduction in yield stress.When adding with NPPD,the heterogeneous nucleation of NPPD contributes to the reduction in yield stress for waxy model oil.Interestingly,the magnetic field is helpful for the modification of yield stress at a lower frequency and intensity before the optimal value;however,the modification is found to be weakened when the magnetic field is further increased after the optimal value.Possible explanation is proposed that the aggregation morphology of wax crystal would be altered and results in the release of wrapped oil phase from the network structure under the magnetic field.

Influence of chemical reaction on heat and mass transfer of non-Newtonian fluid with yield stress by free convection from vertical surface in porous medium considering Soret effect

The effect of chemical reaction on free convection heat and mass transfer for a non-Newtonian power law fluid over a vertical flat plate embedded in a fluid-saturated porous medium has been studied in the presence of the yield stress and the Soret effect. The governing boundary layer equations and boundary conditions are cast into a dimen- sionless form by similarity transformations, and the resulting system of equations is solved by a finite difference method. The results are preSented and discussed for concentration profiles, as well as the Nusselt number and the Sherwood number for various values of the parameters, which govern the problem. The results obtained show that the flow field is influenced appreciably by the presence of the chemical reaction parameter γ the order of.the chemical reaction parameter m, the Soret number St, the buoyancy ratio N, the Lewis number Le, and the dimensionless rheological parameter Ω.

Characterization of Yield Stress Development of Cement Paste by Electrical Resistivity

Yield stress development of cement paste is potentially governed by percolation of 3-dimensional links formed by hydration products on the surface of the particles. It rises steadily at a gradual rate before a sudden increase in rate of growth. In this study, a method was proposed to predict the yield stress development based on the diameter of spread（D） of mini slump cone test and gradient from electrical resistivity measurement（Km）. To evaluate the significance of（D） and（Km） in terms of yield stress, they were quantitatively compared to the initial yield stress（τ0） and rate of yield stress growth（K） obtained from a rheometer. A mathematical relationship between the yield stress of cement paste, diameter of spread and electrical resistivity characteristic gradient was developed. The equation developed can be used as an alternative method to estimate yield stress of cement paste.

Stacking fault energy,yield stress anomaly, and twinnability of Ni_3Al:A first principles study

Using first principles calculations combined with the quasiharmonic approach, we study the effects of temperature on the elastic constants, generalized stacking fault energies, and generalized planar fault energies of Ni3Al. The antiphase boundary energies, complex stacking fault energies, superlattice intrinsic stacking fault energies, and twinning energies decrease slightly with temperature. Temperature dependent anomalous yield stress of Ni3Al is predicted by the energybased criterion based on elastic anisotropy and antiphase boundary energies. It is found that p increases with temperature and this can give a more accurate description of the anomalous yield stress in Ni3Al. Furthermore, the predicted twinnablity of Ni3Al is also decreasing with temperature.

Inherent relations between yield stress and stability of bubble petroleum coke water slurry

The stability of petroleum coke water slurry（PCWS） is currently a hot topic. The inherent relationship between yield stress and stability of bubble-PCWS was studied through orthogonal experiments and range analysis in this work. The results showed that the stability of bubble-PCWS was positively related to the yield stress and that the yield stress could be greatly impacted by the operation conditions during preparation of bubble-PCWS. The main factors affecting the yield stress of bubble-PCWS were solid concentration, aeration time and dosage of frother. However, the effects of aperture size of air distribution plates and type of frother on the yield stress were slight within the experimental range. The optimal conditions for the greatest yield stress were as follows： aeration time of 30 min, solid concentration of 65 wt%, frother dosage of0.030 wt% of the air-dried pulverized petroleum coke, aperture size of air distribution plate of 2-5 lm and AOS frother.The yield stress and the pour rate of bubble-PCWS under this optimum operation condition could reach maxima of more than 0.4 Pa and 96%, respectively.

Principle and practice of coupling support of double yielding shell of soft rock roadway under high stress

In order to ensure the safety and stability of the soft rock roadway under high stress, based on the char- acteristics of the surrounding rock deformation and failure, this paper presented the support technology“coupling support of double yielding shell”, then gave the design method of inner and outer shells and analyzed the principle and requirements of the support technology by taking the -850 meast belt mad-way of Qujiang coal mine as the background. The field application results show that the support technol- ogy can control the soft rock roadway deformation better under high stress. The displacement between roadway sides was 851 mm, the displacement of the roof was 430 mm, and the displacement of the floor was 510 mm.

Influence of pre- plastic deformation on thermal residual stress and yield strength of SiC_w/Al composites

With a micro mechanical model, the feasibility of modification of thermal residual stress of the composites treated by tensile pre plastic deformation was analyzed. The relationship between pre plastic strain and variation of thermal residual stress was established. By using the method of tensile pre plastic deformation, the thermal residual stress in 20%SiC w/6061Al composites was modified. The results show that, with increasing tensile pre plastic strain, the tensile residual stress in the matrix was decreased to zero gradually, and then it was turned into compressive stress. By comparison, it was found that the changing tendency of the test results is similar to that of theoretical analysis. In addition, due to pre plastic deformation, the dislocation density in the matrix was increased, and the yield strength of the composites was improved. The increasing yield strength is mainly due to the decreasing tensile residual stress and the changing of distribution of dislocation in the matrix.

Interactive effects of drought stress and chitosan application on physiological characteristics and essential oil yield of Thymus daenensis Celak

Thymus daenensis, a perennial herb, is often grown in areas that experience drought conditions during its growing period. Application of chitosan may compensate for the negative impact of drought stress on the yield of oil and secondary metabolites in Thymus.The interactive effects of foliar application of chitosan and drought stress on dry matter,essential oil yield, and selected physiological characteristics including photosynthetic pigments, osmotic adjustment, and lipid peroxidation of Thymus were investigated in a two-year study from 2014 to 2015. Treatments consisted of 0, 200, and 400(iL L'1 chitosan applied to plants grown under field capacity, mild drought stress(50% field capacity), and severe drought stress(25% field capacity). Dry matter yield decreased substantially as drought stress intensified. However, essential oil content increased under stress conditions,with the highest essential oil yield obtained from plants under mild drought stress. Foliar application of chitosan compensated to some extent for dry matter and oil yield reduction of plants grown under drought stress. The highest essential oil yield(1.52 g plant-1) was obtained by application of 400 \iL L_1 chitosan under the mild stress condition in 2015 when plants were mature. The compensatory effect of chitosan in reducing the negative impact of stress conditions on dry matter and oil yield was due mainly to stimulation of osmotic adjustment through proline accumulation and reduction of lipid peroxidase level, which increased the integrity of cell membranes of thyme leaves.

Effects of UV-B Radiation and Water Stress on Soybean Yield

Soybean Dongnong 47 was subjected to the experiments of increasing UV-B radiation and water stress on soybean yield components in different growth periods. The results showed that 100-seed weight greatly increased during the early stage of pod filling in the treatment of weak UV-B radiation, seed number per plant as well as seed weight per plant and Dongnong47 yield also increased, while the yield and yield components of Dongnong47 during the blossom to mature period were negatively affected in the treatment of intensive UV-B radiation. 100-seed weight of Dongnong47 all increased in the double factor treatments of UV-B radiation and water stress, with the drought intensified, seed number per plant, seed weight per plant and yield of Dongnong47 decreased, the change of 100-seed weight were various and the antagonistic action of UV-B radiation and water stress were related with their intensity.

Effect of thermal residual stresses on yielding behavior under tensile or compressive loading of short fiber reinforced metal matrix composite

Using large strain two dimension axisymmetric elasto plastic finite element method and the modified law of mixture, the effects of thermal residual stresses on the yielding behavior of short fiber reinforced metal matrix composite and their dependencies on the material structure parameters (fiber volume fraction, fiber aspect ratio and fiber end distance) were studied. It is demonstrated that the stress strain partition parameter can be used to describe the stress transfer from the matrix to the fiber. The variation of the second derivation of the stress strain partition parameter can be used to determine the elastic modulus, the proportion limit, the initial and final yield strengths. In the presence of thermal residual stress, these yielding properties are asymmetric and are influenced differently by the material structure parameters under tensile and compressive loadings.