MODELING THE STRESS-STRAIN CURVES UNDER DYNAMIC RECRYSTALLIZATION

An analytical model for dynamic recrystallization (DRX) is studied based on the relative grain size model proposed by Sakai and Jonas, and the characteristic flow behaviors under DRX are analyzed and simulated. Introducing the variation of dynamic grain size and the heterogeneous distribution of disolo- cation densities densities under DRX,a simple method for modeling and simulating DRX processes is developed by using Laplace transformation theory. The results derived from the present model agree well with the experimental results in literatures. This simulation can reproduce a number of features in DRX flow behaviors, for example,single and multiple peak flow behaviors followed by a steady state flow, the transition between them, and so on.

ISOCHRONOUS STRESS-STRAIN CURVES OF LOW ALLOY STEEL CROSS-WELD-SPECIMEN AT HIGH TEMPERATURE

In this work, a parametric approach is presented and utilized to determine the creep properties of weldments; then the model of creep strain for cross weld specimen is given. On the basis of the experimental results, attempt has been made to establish equations of the isochronous stress-strain for weld joint that can predict the function of loading and service time in use of the creep data of base metal and weld metal.

Numerical simulation of the stress-strain curve and the stress and strain distributions of the titanium-duplex alloy

The stress-strain curve of an α-β Ti-8Mn alloy was measured and then it was calculated with finite element method （FEM） based on the stress-strain curves of the single α and β phase alloys. By comparing the calculated stress-strain curve with the measured one, it can be seen that they fit each other very well. Thus, the FE model built in this work is effective. According to the above mentioned model, the distributions of stress and strain in the α and β phases were simulated. The results show that the stress gradients exist in both α and β phases, and the distributions of stress are inhomogeneous. The stress inside the phase is generally higher than that near the interface. Meanwhile, the stress in the α phase is lower than that in the β phase, whereas the strain in the α phase is higher than that in the β phase.

The Complete Stress-strain Curve of Recycled Aggregate Concrete under Uniaxial Compression Loading

The mechanical performance of recycled aggregate concrete （RAC） is investigated. An experiment on the complete stress-strain curve under uniaxial compression loading of RAC is carried out. The experimental results indicate that the peak stress, peak strain, secant modulus of the peak point and original point increase with the strength grade of RAC enhanced. On the contrary, the residual stress of RAC decreases with the strength grade enhancing, and the failure of RAC is often broken at the interface between the recycled aggregate and the mortar matrix. Finally, the constitutive model of stress-strain model of RAC has been constituted, and the results from the constitutive model of stress-strain meet the experiment results very well.

Charactersitics of Stress-strain Curve of High Strength Steel Fiber Reinforced Concrete under Uniaxial Tension

A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.

Relations of complete creep processes and triaxial stress-strain curves of rock

Based on the results of triaxial compressive creep tests for five kinds of rock under the different stress loading,unloading and cycle-loading-unloading conditions,the creep deformation is not only a function of stress and time,but also it has the corresponding relations to the triaxial stress-strain curves of rock.The deformation properties of soften-strain,harden-strain and ideal plasticity presented by conventional triaxial compressive test curves under the different stress states were utilized,and the creep characteristics,the creep starting stress and the different entire creep process curves of rock were studied systematically according to creep experiment results,and the relations of the triaxial stress-strain curves to the creeping starting stress,the terminating curve,the different creep processes,and the different creep fracture properties were established.The relations presented in this paper were verified partially by the creep experiment results of five types of rock.

MODELLING OF TENSILE STRESS-STRAIN CURVE OF WOVEN FABRICS

A general shape of tensile stress-strain curves of woven fabrics is first recognised by puttingtested and predicted results together.An exponential function with two parameters is then selectedfor the prediction of tensile stress-strain relationship.The predicted results by using the proposedfunction show excellent agreement with experimental data.

Unified analytical stressstrain curve for quasibrittle geomaterial in uniaxial tension, direct shear and uniaxial compression

Considering strain localization in the form of a narrow band initiated just at peak stress, three analytical expressions for stressstrain curves of quasibrittle geomaterial (such as rock and concrete) in uniaxial tension, direct shear and uniaxial compression were presented, respectively. The three derived stressstrain curves were generalized as a unified formula. Beyond the onset of strain localization, a linear strain-softening constitutive relation for localized band was assigned. The size of the band was controlled by internal or characteristic length according to gradient-dependent plasticity. Elastic strain within the entire specimen was assumed to be uniform and decreased with the increase of plastic strain in localized band. Total strain of the specimen was decomposed into elastic and plastic parts. Plastic strain of the specimen was the average value of plastic strains in localized band over the entire specimen. For different heights, the predicted softening branches of the relative stressstrain curves in uniaxial compression are consistent with the previously experimental results for normal concrete specimens. The present expressions for the post-peak stressdeformation curves in uniaxial tension and direct shear agree with the previously numerical results based on gradient-dependent plasticity.

Investigation into the stress-strain curves of deformation-induced ferrite transformation in a low carbon steel

A series of tests of deformation-induced ferrite transformation （DIP-T） in a low carbon steel were carried out by the Gleeble-3500 hot simulation machine at a temperature range of Ae3-Ar3. The overall stress-strain curves during DIFT can be divided into three typical types： ＂double-humped＂,＂ single-humped＂ and ＂transitional＂. The peaks exhibited in the curve are involved with deformation-induced transformation which happened in grains or at the grain boundaries. According to the stress-time curve and strain-time curve, strain capacity dramatically postponed the strain-induced transformation, which leads to the start of the transformation right ahead of the finish of deformation and the majority of the ferrite transformation process mainly happened after the deformation. Deformation-induced transformation is a metadynamic transformation process with dynamic nucleation.

Analysis of plane strain bending of a strain hardening curved beam based on unified yield criterion

The analysis of plane strain elastic-plastic bending of a linear strain hardening curved beam with a narrow rectangular cross section subjected to couples at its end is conducted based on a unified yield criterion. The solutions for the mechanical properties of plane strain bending are derived, which are adapted for various kinds of non-strength differential materials and can be degenerated to those based on the Tresca, von Mises, and twin-shear yield criteria. The dependences of the two critical bending moments, the radii of the interfaces between the elastic and plastic regions and the radial displacements of the points at the symmetrical plane on different yield criteria and Poisson’s ratios are discussed. The results show that the influences of different yield criteria and Poisson’s ratio on the two critical bending moments, the radii of the interfaces between the elastic and plastic regions and the radial displacements of the points at the symmetrical plane of the curved beam are significant. Once the value of bis obtained by experiments, the yield criterion and the corresponding solution for the materials of interest are then determined.

Residual strain evaluation of curved surface by grating-transferring technique and GPA

This paper investigates an advanced grating-transferring technique combined with geometric phase analysis (GPA) for residual strain evaluation of curved surface.A standard holographic grating is first transferred to a pre-produced epoxy resin film and then consolidated to a test region of curved surface.With a rubber mold and silicone rubber the deformed grating is replicated to a sheet metal after hole-drilling for release of residual stress.After that the grating is transferred from the sheet metal to the glass plate,which would be served as an analyzer grating (specimen grating).By GPA the local strain distributions related to the phase difference between the reference grating and analyzer grating for the released stress can be evaluated.A validation test has been conducted on the weld joint of a stainless steel tube and the obtained results demonstrate the ability of the method in measuring the residual strain of curved surface.

Evaluating instrumented Charpy impact strain signals using curve fitting equations

An effective and simple way to develop equations from impact strain signals was proposed.Little research has been performed in this area,but this equation is very important for evaluating input signals in finite element analysis impact tests and for obtaining additional information on material deformation and fracture processes under impact loading.For this purpose,dynamic impact responses were examined through signals obtained from a strain gauge installed on an impact striker connected to a data acquisition system.Aluminium 6061-T6 was used to extract strain responses on the striker during Charpy impact testing.Statistical analysis was performed using the I-kaz method,and curve fitting equations based on the equation for vibration response under a non-periodic force were used to evaluate the Charpy impact signals.The I-kaz coefficients and curve fitting equations were then compared and discussed with related parameters,such as velocities and thicknesses.Velocity and thickness were found to be related to the strain signal patterns,curve fitting equations and I-kaz coefficients.The equations developed using this method had R2 values greater than 97.7%.Finally,the constructed equations were determined to be suitable for evaluating Charpy impact strain signal patterns and obtaining additional information on fracture processes under impact loading.

Ground reaction curves for circular excavations in non-homogeneous,axisymmetric strain-softening rock masses

Fast methods to solve the unloading problem of a cylindrical cavity or tunnel excavated in elasto-perfectly plastic, elasto-brittle or strain-softening materials under a hydrostatic stress feld can be derived based on the self-similarity of the solution. As a consequence, they only apply when the rock mass is homogeneous and so exclude many cases of practical interest. We describe a robust and fast numerical technique that solves the tunnel unloading problem and estimates the ground reaction curve for a cylindrical cavity excavated in a rock mass with properties depending on the radial coordinate, where the solution is no longer self-similar. The solution is based on a continuation-like approach(associated with the unloading and with the incremental formulation of the elasto-plastic behavior), fnite element spatial discretization and a combination of explicit sub-stepping schemes and implicit techniques to integrate the constitutive law, so as to tackle the diffculties associated with both strong strain-softening and elasto-brittle behaviors. The developed algorithm is used for two practical ground reaction curve computation applications. The frst application refers to a tunnel surrounded by an aureole of material damaged by blasting and the second to a tunnel surrounded by a ring-like zone of reinforced(rock-bolted) material.

Planar Cardinal Spline Curves with Minimum Strain Energy

In this paper, we focus on how to use strain energy minimization to obtain the optimal value of the fl＇ee parameter of the planar Cardinal spline curves. The unique solution can be easily obtained by minimizing an appropriate approximation of the strain energy. An example is presented to illustrate the effectiveness of our method.

Finite Element Modeling of Stress Strain Curve and Micro Stress and Micro Strain Distributions of Titanium Alloys— A Review

Most of the alloys like titanium, steel, brass, copper, etc., are used in engineering applications like automobile, aero- space, marine etc., consist of two or more phases. If a material consists of two or more phases or components it is very difficult to predict the properties like mechanical and other properties based on simple laws such as rule of mixtures. Titanium alloys are capable of producing different microstructures when it subjected to heat treatments, so much of money and time are squandering to study the effect of microstructure on mechanical properties of titanium alloys. This squandering can be reduced with the help of modeling and optimization techniques. There are many modeling tech- niques like Finite element method, Mat lab, Mathematical modeling etc. are available. But Finite element method is widely used for prediction because of capable of producing distributions of stresses and strains at any different loads. From the literature it is observed that there is a good agreement between the calculated and measured stress strain curves. This review paper describes the effect of volume fraction and grain size of alpha phase on the stress strain curve of the titanium alloys. It also can predict the effect of strength ratio on stress strain curve by using FEM. This informa- tion will be of great use in designing and selecting the titanium alloys for various engineering applications.

Stress—strain curves for different loading paths and yield loci of aluminum alloy sheets

To carry out biaxial tensile test in sheet metal, the biaxial tensile testing system was established. True stress—true strain curves of three kinds of aluminum alloy sheets for loading ratios of 4:1, 4:2, 4:3, 4:4, 3:4, 2:4 and 1:4 were obtained by conducting biaxial tensile test in the established testing systems. It shows that the loading path has a significant influence on the stress—strain curves and as the loading ratio increases from 4:1 to 4:4, the stress—strain curve becomes higher and n-value becomes larger. Experimental yield points for three aluminum alloy sheets from 0.2% to 2% plastic strain were determined based on the equivalent plastic work. And the geometry of the experimental yield loci were compared with the yield loci calculated from several existing yield criteria. The analytical result shows that the Barlat89 and Hosford yield criterion describe the general trends of the experimental yield loci of aluminum alloy sheets well, whereas the Mises yield criterion overestimates the yield stress in all the contours.

Discussion on relationship between minimal energy and curve shapes

Energy minimization has been widely used for constructing curve and surface in the fields such as computer-aided geometric design, computer graphics. However, our testing examples show that energy minimization does not optimize the shape of the curve sometimes. This paper studies the relationship between minimizing strain energy and curve shapes, the study is carried out by constructing a cubic Hermite curve with satisfactory shape. The cubic Hermite curve interpolates the positions and tangent vectors of two given endpoints. Computer simulation technique has become one of the methods of scientific discovery, the study process is carried out by numerical computation and computer simulation technique. Our result shows that： （1） cubic Hermite curves cannot be constructed by solely minimizing the strain energy; （2） by adoption of a local minimum value of the strain energy, the shapes of cubic Hermite curves could be determined for about 60 percent of all cases, some of which have unsatisfactory shapes, however. Based on strain energy model and analysis, a new model is presented for constructing cubic Hermite curves with satisfactory shapes, which is a modification of strain energy model. The new model uses an explicit formula to compute the magnitudes of the two tangent vectors, and has the properties： （1） it is easy to compute; （2） it makes the cubic Hermite curves have satisfactory shapes while holding the good property of minimizing strain energy for some cases in curve construction. The comparison of the new model with the minimum strain energy model is included.

Sheet metal hardening curve determined by laminated sample and its adaptability to sheet forming processes

The hardening curve for sheet metal can be determined from the load-displacement curve of tensile specimen with rectangular cross-section. Therefore,uniaxial compression test on cylinder specimen made from laminated sample is put forward. Considering the influence of anisotropy on hardening properties and the stress state in popular forming process,plane strain compression test on cubic specimen made from laminated sample was advanced. Results show that the deformation range of hardening curves obtained from the presented methods is wide,which meets the need for the application in sheet metal forming processes. In view of the characteristics of methods presented in the paper and the stress strain state of various forming processes,the adaptability of the two methods presented in this paper is given.

On the plastic buckling of curved carbon nanotubes

This research,for the first time,predicts theoretically static stability response of a curved carbon nanotube(CCNT)under an elastoplastic behavior with several boundary conditions.The CCNT is exposed to axial compressive loads.The equilibrium equations are extracted regarding the Euler–Bernoulli displacement field by means of the principle of minimizing total potential energy.The elastoplastic stress-strain is concerned with Ramberg–Osgood law on the basis of deformation and flow theories of plasticity.To seize the nano-mechanical behavior of the CCNT,the nonlocal strain gradient elasticity theory is taken into account.The obtained differential equations are solved using the Rayleigh–Ritz method based on a new admissible shape function which is able to analyze stability problems.To authorize the solution,some comparisons are illustrated which show a very good agreement with the published works.Conclusively,the best findings confirm that a plastic analysis is crucial in predicting the mechanical strength of CCNTs.

BUCKLING OF SPATIAL CURVED RODS WITH CIRCULAR CROSS-SECTIONS

Formulae for determining Green strain of an initially curved and twisted rod with circular cross-sections are derived by using the natural (curvilinear) coordinate system. Finite element analyses are performed for the flexural buckling of initially curved and twisted thin rods under simultaneous action of axial force and torque. Numerical examples demonstrate that the given formulae are correcte. Some numerical results are compared with existing analytical solutions and data obtained by commercial FE software. The convergence of the proposed curved element is better than that of elements in the commercial FE software. It is shown that good accuracy and convergency are achieved by solving three-dimensional problems.